32bpp means ARGB 8888 in the driver, therfore the transparency length
and offset should be 8 and 24 respectively. However, the transparency
length and offset were previously 0, which means that the driver supports
RGB 888 without alpha blending when 32bpp is used.
So, the transparency checking in 32bpp is corrected so that the
transparency length and offset are 8 and 24 respectively.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds gpio setup function to resume function to ensure
gpio used by FIMD IP and LCD panel during a resume.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Compared to s3c64xx, S5P series such as S5PC100 and S5PV210 have
the different window features including valid bpp, palette size
and palette bpp. Therefore, window variant information for S5P
should be added.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Additional validate bpps are added to windows as follows:
window0: 18 bpp for RGB666
window1, 2 and 3: 28 bpp for ARGB4888
window4: 19 bpp for ARGB1666, 28 bpp for ARGB4888
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Offset values for OSD size registers of window 1 and 2 are corrected.
The offset values of OSD size registers are as follows:
window0: VIDOSDC (0x8)
window1 and 2: VIDOSDD (0xc)
window3 and 4: not present
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Request_mem_region should be used with release_mem_region, not
release_resource.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@s exists@
expression e1,e2,e3,e4,e;
@@
*e4 = request_mem_region(e1,e2,e3)
... when != e4 = e
*release_resource(e4);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The spinlock is added to interrupt routine to ensure that the driver
is protected against multiple accesses.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the checkpatch errors listed below:
ERROR: space required before the open parenthesis '('
ERROR: need consistent spacing around '+' (ctx:WxV)
ERROR: space prohibited before that close parenthesis ')'
Also, following warning is fixed by adding 'platid' variable
which can reduce number of lines exceeding 80 characters.
WARNING: line over 80 characters
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Return PTR_ERR(sfb->bus_clk) instead of 0 if clk_get fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for runtime pm using the functions.
- pm_runtime_get_sync()
- pm_runtime_put_sync()
pm_runtime_get_sync() and pm_runtime_put_sync() are called when
open or release function of framebufer driver is called to inform
the system if hardware is idle or not.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a simple algorithm which calculates the pixel clock based on the video
mode parameters. This is only done when no pixel clock is supplied
through the platform data.
This allows drivers to omit the pixel clock data and thus share the
algorithm used for calculating it.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Cc: Pawel Osciak <p.osciak@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Tested-by: Donghwa Lee <yiffie9819@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
S5PV210 SoCs allow enabling/disabling DMA channels per window. For a
window to display data from framebuffer memory, its channel has to be
enabled.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the following section mismatch errors:
WARNING: vmlinux.o(.data+0x20b40): Section mismatch in reference from the variable s3c_fb_driver_ids to the (unknown reference) .devinit.data:(unknown)
The variable s3c_fb_driver_ids references
the (unknown reference) __devinitdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0x20b58): Section mismatch in reference from the variable s3c_fb_driver_ids to the (unknown reference) .devinit.data:(unknown)
The variable s3c_fb_driver_ids references
the (unknown reference) __devinitdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0x20b70): Section mismatch in reference from the variable s3c_fb_driver_ids to the (unknown reference) .devinit.data:(unknown)
The variable s3c_fb_driver_ids references
the (unknown reference) __devinitdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Newer hardware (S3C6410, S5P) have the ability to block updates from
shadow registers during reconfiguration. Add protect calls for set_par
and clear protection when resetting.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
S3C64xx and S5P OSD registers for OSD size and alpha are as follows:
VIDOSDC: win 0 - size, win 1-4: alpha
VIDOSDD: win 1-2 - size; not present for windows 0, 3 and 4
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add VSYNC interrupt support and an ioctl that allows waiting for it.
Interrupts are turned on only when needed.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Supports all bpp modes.
The PRTCON register is used to disable in-hardware updates of registers
that store start and end addresses of framebuffer memory. This prevents
display corruption in case we do not make it before VSYNC with updating
them atomically. With this feature there is no need to wait for a VSYNC
interrupt before each such update.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
S5PC100 and S5PV210 framebuffer devices differ slightly in terms of
available registers and their driver data structures have to be separate.
Those differences include dissimilar ways to control shadow register
updates.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following problems were found in the above situation:
sfb->windows[win] was being assigned at the end of s3c_fb_probe_win only.
This resulted in passing a NULL to s3c_fb_release_win if probe_win
returned early and a memory leak.
dma_free_writecombine does not allow its third argument to be NULL.
fb_dealloc_cmap does not verify whether its argument is not NULL.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the palette setup code from the header files and put it into the
main driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: KyungMin Park <kyungmin.park.samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the variant and window variant structures with the necessary
changes to support the older style of hardware where these are not in the
same place.
Add the support for the s3c2443/s3c2416 hardware by using the
platform-device s3c2443 to cover both, and add the initialisation data for
these.
Also change to including just the v4 header files for the moment until the
last of the merging of these is sorted out.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: KyungMin Park <kyungmin.park.samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the various header files that configure this driver and use the
platform device name to select the correct configuration at probe time.
Currently this does not remove the header files, only updates the driver
and the relevant platform files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: KyungMin Park <kyungmin.park.samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver clears all windows, but also sets the windows' colour key
controls at the same time. However, the last window does not have these
registers as it is always blended into the previous window.
Move the colour key initialisation into the probe, and run it for only
nr_win-1 windows.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: KyungMin Park <kyungmin.park.samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It has been working fine at 16bpp but in case of pixel format more then
24bpp it would occur distortedness situation on that mode. so this patch
set the word swap control bit of WINCONx to 1 as default value. but it
should be set to 0 in case that each ENLOCAL bit of WINCON0 ~ 2 registers
is enabled. this issue would be solved with local path feature soon.
Signed-off-by: InKi Dae <inki.dae@samsung.com>
Reviewed-by: KyungMin Park <kyungmin.park.samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
s5pv210 has five window layers (window0 ~ 4), among them, window0 ~ 2
could be used for local path with fimc(capture device) and fimd writeback
feature so this patch makes default window layer for UI to be set at
machine code.
Signed-off-by: InKi Dae <inki.dae@samsung.com>
Reviewed-by: KyungMin Park <kyungmin.park.samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Fix divide by zero and broken output. Commit 600ce1a0fa ("fix clock
setting for Samsung SoC Framebuffer") introduced a mandatory refresh
parameter to the platform data for the S3C framebuffer but did not
introduce any validation code, causing existing platforms (none of which
have refresh set) to divide by zero whenever the framebuffer is
configured, generating warnings and unusable output.
Ben Dooks noted several problems with the patch:
- The platform data supplies the pixclk directly and should already
have taken care of the refresh rate.
- The addition of a window ID parameter doesn't help since only the
root framebuffer can control the pixclk.
- pixclk is specified in picoseconds (rather than Hz) as the patch
assumed.
and suggests reverting the commit so do that. Without fixing this no
mainline user of the driver will produce output.
[akpm@linux-foundation.org: don't revert the correct bit]
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes `s3c_fb_remove' referenced in section `.data' of
drivers/built-in.o: defined in discarded section `.devexit.text' of
drivers/built-in.o
With CONFIG_HOTPLUG=n, functions marked with __devexit gets removed,
so make sure we use __devexit_p when referencing pointers to them.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixed off-by-one bug in loop indexes - some elements beyond windows' array
were accessed, which might result in memory access violations when
removing/suspending the device.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All resources are released in s3c_fb_win_release so remove other places of
resources releasing. Add releasing of an allocated fb_info structure as
well.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the ARGB1888 and ARGB4888 hardware to the Samsung SoC
Framebuffer driver (s3c-fb.c).
ARGB1888 and ARGB4888 is decided by var->transp.length and this variable
is set by s3c_fb_check_var().
In s3c_fb_check_var(), if var->vits_per_pixel is 25 or 28, then
var->transp.length would be 1 or 3.
Therefore alpha mode(ARGB1888 or ARGB4888) could be decided through that
variable.
For using alpha mode, you need to set the following: This code should be
added to your machine code as platform data.
static struct s3c_fb_pd_win xxx_fb_win0 = {
/* this is to ensure we use win0 */
.win_mode = {
.pixclock = (8+8+8+240)*(38+4+38+400),
.left_margin = 8,
.right_margin = 8,
.upper_margin = 38,
.lower_margin = 38,
.hsync_len = 8,
.vsync_len = 4,
.xres = 240,
.yres = 400,
},
.max_bpp = 32,
.default_bpp = 24,
};
static struct s3c_fb_pd_win xxx_fb_win1 = {
.win_mode = {
.pixclock = (8+8+8+240)*(38+4+38+400),
.left_margin = 8,
.right_margin = 8,
.upper_margin = 38,
.lower_margin = 38,
.hsync_len = 8,
.vsync_len = 4,
.xres = 240,
.yres = 400,
},
.max_bpp = 32,
.default_bpp = 28,
};
static struct s3c_fb_platdata xxx_lcd_pdata __initdata = {
.win[0] = &ncp_fb_win0,
.win[1] = &ncp_fb_win1,
.vidcon0 = VIDCON0_VIDOUT_RGB | VIDCON0_PNRMODE_RGB,
.vidcon1 = VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC,
.setup_gpio = xxx_fb_gpio_setup,
};
s3c_fb_set_platdata(&xxx_lcd_pdata);
The above code sets pixelformat for window0 layer to RGB888 and window1
layer to ARGB4888.
Signed-off-by: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correctly restore the FrameBuffer register state in the resume function.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the newer Samsung devices, such as found in the S3C2443,
S3C6400 or S3C6410 series SoC.
It currently does not support all the alpha- or chroma-key options but it
will support more exporting more than one framebuffer ready for adding
overlay and blending functions.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
