Change to follow the Kconfig style guide. This patch fixes to use tab
rather than space to indent, while help text is indented an additional
two spaces.
Link: https://lore.kernel.org/r/20220815025006.48167-1-mie@igel.co.jp
Fixes: e35f56bb03 ("PCI: endpoint: Support NTB transfer between RC and EP")
Signed-off-by: Shunsuke Mie <mie@igel.co.jp>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
On Qualcomm platforms like SC8280XP and SA8540P, interconnect bandwidth
must be requested before enabling interconnect clocks.
Add basic support for managing an optional "pcie-mem" interconnect path
by setting a low constraint before enabling clocks and updating it after
the link is up.
Note that it is not possible for a controller driver to set anything but
a maximum peak bandwidth as expected average bandwidth will vary with
use case and actual use (and power policy?). This very much remains an
unresolved problem with the interconnect framework.
Also note that no constraint is set for the SC8280XP/SA8540P "cpu-pcie"
path for now as it is not clear what an appropriate constraint would be
(and the system does not crash when left unspecified).
Link: https://lore.kernel.org/r/20221102090705.23634-3-johan+linaro@kernel.org
Fixes: 70574511f3 ("PCI: qcom: Add support for SC8280XP")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
MSI remapping is disabled by VMD driver for Intel's Icelake and
newer systems in order to improve performance by setting
VMCONFIG_MSI_REMAP. By design VMCONFIG_MSI_REMAP register is cleared
by firmware during boot. The same register gets cleared when system
is put in S3 power state. VMD driver needs to set this register again
in order to avoid interrupt issues with devices behind VMD if MSI
remapping was disabled before.
Link: https://lore.kernel.org/r/20221109142652.450998-1-nirmal.patel@linux.intel.com
Fixes: ee81ee84f8 ("PCI: vmd: Disable MSI-X remapping when possible")
Signed-off-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Francisco Munoz <francisco.munoz.ruiz@linux.intel.com>
Set RCB_MPS mode bit so that data for PCIe read requests up to the size of
the Maximum Payload Size (MPS) are returned in one completion, and data for
PCIe read requests greater than the MPS are split at the specified Read
Completion Boundary setting.
Set RCB_64B so that the Read Compeletion Boundary is 64B.
Link: https://lore.kernel.org/r/20221011184211.18128-6-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
A number of inline functions are called rarely and/or are not
time-critical. Take out the "inline" and let the compiler do its work.
Link: https://lore.kernel.org/r/20221011184211.18128-5-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
It would be nice to replace the PCIe link-up loop as well but
there are too many uses of this that do not poll (and the
read_poll_timeout uses "timeout==0" to loop forever).
Link: https://lore.kernel.org/r/20221011184211.18128-4-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Be prudent and give some time for power and clocks to become stable. As
described in the PCIe CEM specification sections 2.2 and 2.2.1; as well as
PCIe r5.0, 6.6.1.
Link: https://lore.kernel.org/r/20221011184211.18128-3-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
We always wanted to enable Multi-MSI but didn't have a test device until
recently. In addition, there are some devices out there that will ask for
multiple MSI but refuse to work if they are only granted one.
Link: https://lore.kernel.org/r/20221011184211.18128-2-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Many host controller drivers #include <linux/of_irq.h> even though they
don't need it. Remove the unnecessary #includes.
Link: https://lore.kernel.org/r/20221031153954.1163623-6-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Roy Zang <roy.zang@nxp.com>
pci-xgene-msi.c uses irq_domain_add_linear() and related interfaces, so it
needs <linux/irqdomain.h> but doesn't include it directly; it relies on the
fact that <linux/of_irq.h> includes it.
But pci-xgene-msi.c *doesn't* need <linux/of_irq.h> itself. Include
<linux/irqdomain.h> directly to remove this implicit dependency so a future
patch can drop <linux/of_irq.h>.
Link: https://lore.kernel.org/r/20221031153954.1163623-5-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci-mvebu.c uses irq_domain_add_linear() and related interfaces but relies
on <linux/irqdomain.h> but doesn't include it directly; it relies on the
fact that <linux/of_irq.h> includes it.
Include <linux/irqdomain.h> directly to remove this implicit dependency.
Link: https://lore.kernel.org/r/20221031153954.1163623-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
pcie-microchip-host.c uses irq_domain_add_linear() and related interfaces,
so it needs <linux/irqdomain.h> but doesn't include it directly; it relies
on the fact that <linux/of_irq.h> includes it.
But pcie-microchip-host.c *doesn't* need <linux/of_irq.h> itself. Include
<linux/irqdomain.h> directly to remove this implicit dependency so a future
patch can drop <linux/of_irq.h>.
Link: https://lore.kernel.org/r/20221031153954.1163623-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
pcie-altera-msi.c uses irq_domain_add_linear() and related interfaces, so
it needs <linux/irqdomain.h> but doesn't include it directly; it relies on
the fact that <linux/of_irq.h> includes it.
But pcie-altera-msi.c *doesn't* need <linux/of_irq.h> itself. Include
<linux/irqdomain.h> directly to remove this implicit dependency so a future
patch can drop <linux/of_irq.h>.
Link: https://lore.kernel.org/r/20221031153954.1163623-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some of the platforms (like Tegra194 and Tegra234) have open slots and
not having an endpoint connected to the slot is not an error.
So, changing the macro from dev_err to dev_info to log the event.
Link: https://lore.kernel.org/r/20220913101237.4337-1-vidyas@nvidia.com
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
When pci_create_attr() fails, pci_remove_resource_files() is called which
will iterate over the res_attr[_wc] arrays and frees every non NULL entry.
To avoid a double free here set the array entry only after it's clear we
successfully initialized it.
Fixes: b562ec8f74 ("PCI: Don't leak memory if sysfs_create_bin_file() fails")
Link: https://lore.kernel.org/r/20221007070735.GX986@pengutronix.de/
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Replace assignment of PCI domain IDs from atomic_inc_return() to
ida_alloc().
Use two IDAs, one for static domain allocations (those which are defined in
device tree) and second for dynamic allocations (all other).
During removal of root bus / host bridge, also release the domain ID. The
released ID can be reused again, for example when dynamically loading and
unloading native PCI host bridge drivers.
This change also allows to mix static device tree assignment and dynamic by
kernel as all static allocations are reserved in dynamic pool.
[bhelgaas: set "err" if "bus->domain_nr < 0"]
Link: https://lore.kernel.org/r/20220714184130.5436-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe r2.0, sec 7.8 added Link Capabilities/Status/Control 2 registers to
the PCIe Capability with Capability Version 2.
Previously we assumed these registers were implemented for all PCIe
Capabilities of version 2 or greater, but in fact they are only
implemented for devices with Links.
Update pcie_capability_reg_implemented() to check whether the device has
a Link.
[bhelgaas: commit log, squash export]
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209100057070.2275@angie.orcam.me.uk
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209100057300.2275@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pci_epf_test_notifier function should be installed also if only
core_init_notifier is enabled. Fix the current logic.
Link: https://lore.kernel.org/r/20220825090101.20474-1-hayashi.kunihiko@socionext.com
Fixes: 5e50ee27d4 ("PCI: pci-epf-test: Add support to defer core initialization")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Om Prakash Singh <omp@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
[devm_]gpiod_get_from_of_node in drivers usage should be limited
so that gpiolib can be cleaned up; let's switch to the generic device
property API.
It may even help with handling secondary fwnodes when gpiolib is taught
to handle gpios described by swnodes.
Link: https://lore.kernel.org/r/20220903-gpiod_get_from_of_node-remove-v1-1-b29adfb27a6c@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[lpieralisi@kernel.org: commit log]
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Since there is no release callback defined for the PCI EPC device,
the below warning is thrown by driver core when a PCI endpoint driver is
removed:
Device 'e65d0000.pcie-ep' does not have a release() function, it is broken and must be fixed. See Documentation/core-api/kobject.rst.
WARNING: CPU: 0 PID: 139 at drivers/base/core.c:2232 device_release+0x78/0x8c
Hence, add the release callback and also move the kfree(epc) from
pci_epc_destroy() so that the epc memory is freed when all references are
dropped.
Link: https://lore.kernel.org/r/20220623003817.298173-1-yoshihiro.shimoda.uh@renesas.com
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Dual mode DesignWare PCIe IP has PTM capability enabled (if supported) even
in the EP mode. The PCIe compliance for the EP mode expects PTM
capabilities (ROOT_CAPABLE, RES_CAPABLE, CLK_GRAN) be disabled.
Hence disable PTM for the EP mode.
Link: https://lore.kernel.org/r/20220919143340.4527-3-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
commit aeaa0bfe89 ("PCI: dwc: Move N_FTS setup to common setup")
incorrectly uses pci->link_gen in deriving the index to the
n_fts[] array also introducing the issue of accessing beyond the
boundaries of array for greater than Gen-2 speeds. This change fixes
that issue.
Link: https://lore.kernel.org/r/20220926111923.22487-1-vidyas@nvidia.com
Fixes: aeaa0bfe89 ("PCI: dwc: Move N_FTS setup to common setup")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
1a1daf097e ("PCI/PM: Remove unused pci_driver.suspend_late() hook")
removed the legacy .suspend_late() hook, which was the only user of the
"state" parameter to pci_legacy_suspend_late(), but it neglected to remove
the parameter.
Remove the unused "state" parameter to pci_legacy_suspend_late().
Link: https://lore.kernel.org/r/20221025193502.669091-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pcie_port_service_register() and pcie_port_service_unregister() are used
only by the pciehp, aer, dpc, and pme PCIe port service drivers, none of
which can be modules. Unexport pcie_port_service_register() and
pcie_port_service_unregister(). No functional change intended.
Link: https://lore.kernel.org/r/20221019204127.44463-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Previously several things used by portdrv_core.c and portdrv_pci.c were
shared by defining them in portdrv.h. Now that portdrv_core.c and
portdrv_pci.c have been squashed, move things that can be private into
portdrv.c. No functional change intended.
Link: https://lore.kernel.org/r/20221019204127.44463-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Squash portdrv_core.c and portdrv_pci.c into portdrv.c to make it easier to
find things. The whole thing is less than 1000 lines, and it's a pain to
bounce back and forth between two files.
Several portdrv_core.c functions were non-static because they were
referenced from portdrv_pci.c. Make them static since they're now all in
portdrv.c.
No functional change intended.
Link: https://lore.kernel.org/r/20221019204127.44463-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
-----BEGIN PGP SIGNATURE-----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=gs3v
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.1-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci fix from Bjorn Helgaas:
"Revert the attempt to distribute spare resources to unconfigured
hotplug bridges at boot time.
This fixed some dock hot-add scenarios, but Jonathan Cameron reported
that it broke a topology with a multi-function device where one
function was a Switch Upstream Port and the other was an Endpoint"
* tag 'pci-v6.1-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: Distribute available resources for root buses, too"
This reverts commit e96e27fc6f.
Jonathan reported that this commit broke this topology, where all the space
available on bus 02 was assigned to the 02:00.0 bridge window, leaving none
for the e1000 device at 02:00.1:
pci 0000:00:04.0: bridge window [mem 0x10200000-0x103fffff] to [bus 02-04]
pci 0000:02:00.0: bridge window [mem 0x10200000-0x103fffff] to [bus 03-04]
pci 0000:02:00.1: BAR 0: failed to assign [mem size 0x00020000]
e1000 0000:02:00.1: can't ioremap BAR 0: [??? 0x00000000 flags 0x0]
Link: https://lore.kernel.org/r/20221014124553.0000696f@huawei.com
Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCY0ZjFAAKCRCAXGG7T9hj
vjEsAP4rFMnqc6AXy4Mpvv8cxBtEuQZbwEqgBrMJUvK1jZQrBQD/dOJK2GBCVcfD
2yaVlefFiJGTw5WUlbPeohUlTZ8pJwg=
=xsHV
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.1-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- Some minor typo fixes
- A fix of the Xen pcifront driver for supporting the device model to
run in a Linux stub domain
- A cleanup of the pcifront driver
- A series to enable grant-based virtio with Xen on x86
- A cleanup of Xen PV guests to distinguish between safe and faulting
MSR accesses
- Two fixes of the Xen gntdev driver
- Two fixes of the new xen grant DMA driver
* tag 'for-linus-6.1-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Kconfig: Fix spelling mistake "Maxmium" -> "Maximum"
xen/pv: support selecting safe/unsafe msr accesses
xen/pv: refactor msr access functions to support safe and unsafe accesses
xen/pv: fix vendor checks for pmu emulation
xen/pv: add fault recovery control to pmu msr accesses
xen/virtio: enable grant based virtio on x86
xen/virtio: use dom0 as default backend for CONFIG_XEN_VIRTIO_FORCE_GRANT
xen/virtio: restructure xen grant dma setup
xen/pcifront: move xenstore config scanning into sub-function
xen/gntdev: Accommodate VMA splitting
xen/gntdev: Prevent leaking grants
xen/virtio: Fix potential deadlock when accessing xen_grant_dma_devices
xen/virtio: Fix n_pages calculation in xen_grant_dma_map(unmap)_page()
xen/xenbus: Fix spelling mistake "hardward" -> "hardware"
xen-pcifront: Handle missed Connected state
-----BEGIN PGP SIGNATURE-----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=pOqY
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Resource management:
- Distribute spare resources to unconfigured hotplug bridges at
boot-time (not just when hot-adding such a bridge), which makes
hot-adding devices to docks work better.
- Revert to a BAR assignment inherited from firmware only when the
address is actually reachable via any upstream bridges, which fixes
some cases where firmware doesn't configure all devices.
- Add a sysfs interface to resize BARs so this can be done before
assigning devices to a VM through VFIO.
Power management:
- Disable Precision Time Management for all devices on suspend to
enable lower-power PM state. We previously did this just for Root
Ports, which isn't enough because downstream devices can still
generate PTM messages, which cause errors if it's disabled in the
Root Port.
- Save and restore the ASPM L1 PM Substates configuration for
suspend/ resume. Previously this configuration was lost, so L1.x
states likely stopped working after resume.
- Check whether the L1 PM Substates Capability exists. If it didn't
exist, we previously read junk and tried to configure L1 Substates
based on that.
- Fix the LTR_L1.2_THRESHOLD computation, which previously set a
threshold for entering L1.2 that was too low in some cases.
- Reduce the delay after transitions to or from D3cold by using
usleep_range() rather than msleep(), which often slept for ~19ms
instead of the 10ms normally required. The spec says 10ms is
enough, but it's possible we could trip over devices that need a
little more.
Error handling:
- Work around a BIOS bug that caused Intel Root Ports to advertise a
Root Port Programmed I/O (RP PIO) log size of zero, which caused
annoying warnings and prevented the kernel from dumping log
registers for DPC errors.
Qualcomm PCIe controller driver:
- Add support for SC8280XP and SA8540P host controllers and SM8450
endpoint controller.
- Disable Master AXI clock on endpoint controllers to save power when
link is idle or in L1.x.
- Expose link state transition counts via debugfs to help debug
issues with low-power states.
- Add auto-loading module support.
Synopsys DesignWare PCIe controller driver:
- Remove a dependency on ZONE_DMA32 by allocating the MSI target page
differently. There's more work to do related to eDMA controllers,
so it's not completely settled"
* tag 'pci-v6.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (71 commits)
PCI: qcom-ep: Check platform_get_resource_byname() return value
PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Define clocks per platform
PCI: qcom-ep: Make PERST separation optional
dt-bindings: PCI: qcom-ep: Make PERST separation optional
PCI: qcom-ep: Disable Master AXI Clock when there is no PCIe traffic
PCI: Expose PCIe Resizable BAR support via sysfs
PCI/ASPM: Correct LTR_L1.2_THRESHOLD computation
PCI/ASPM: Ignore L1 PM Substates if device lacks capability
PCI/ASPM: Factor out L1 PM Substates configuration
PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SS
PCI: qcom-ep: Expose link transition counts via debugfs
PCI: qcom-ep: Disable IRQs during driver remove
PCI/ASPM: Save L1 PM Substates Capability for suspend/resume
PCI/ASPM: Refactor L1 PM Substates Control Register programming
PCI: qcom-ep: Make use of the cached dev pointer
PCI: qcom-ep: Rely on the clocks supplied by devicetree
PCI: qcom-ep: Add kernel-doc for qcom_pcie_ep structure
phy: freescale: imx8m-pcie: Fix the wrong order of phy_init() and phy_power_on()
...
pcifront_try_connect() and pcifront_attach_devices() share a large
chunk of duplicated code for reading the config information from
Xenstore, which only differs regarding calling pcifront_rescan_root()
or pcifront_scan_root().
Put that code into a new sub-function. It is fine to always call
pcifront_rescan_root() from that common function, as it will fallback
to pcifront_scan_root() if the domain/bus combination isn't known
yet (and pcifront_scan_root() should never be called for an already
known domain/bus combination anyway). In order to avoid duplicate
messages for the fallback case move the check for domain/bus not known
to the beginning of pcifront_rescan_root().
While at it fix the error reporting in case the root-xx node had the
wrong format.
As the return value of pcifront_try_connect() and
pcifront_attach_devices() are not used anywhere make those functions
return void. As an additional bonus this removes the dubious return
of -EFAULT in case of an unexpected driver state.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
- Add macros for PCI Configuration Mechanism #1 and use them in the
ftpci100, mt7621, and tegra drivers (Pali Rohár)
* remotes/lorenzo/pci/misc:
PCI: tegra: Use PCI_CONF1_EXT_ADDRESS() macro
PCI: mt7621: Use PCI_CONF1_EXT_ADDRESS() macro
PCI: ftpci100: Use PCI_CONF1_ADDRESS() macro
PCI: Add standard PCI Config Address macros
- List platforms that use a single MSI host interrupt in qcom DT (Johan
Hovold)
- Add SC8280XP, SA8540P support to qcom DT binding and driver(Johan Hovold)
- Make all optional clocks truly optional in the driver (Johan Hovold)
- Rename per-IP structs to reflect the IP version (Johan Hovold)
- Sort device ID match table by compatible string (Johan Hovold)
- Add MODULE_DEVICE_TABLE to enable module autoloading (Dmitry Baryshkov)
- Drop the unused .post_deinit() callback (Johan Hovold)
- Rely on DT for clock information instead of hard-coding it in the driver
(Manivannan Sadhasivam)
- Disable IRQs when removing driver to avoid spurious IRQs later
(Manivannan Sadhasivam)
- Expose link transition counts via debugfs to help debug issues with
low-power states (Manivannan Sadhasivam)
- Gate Master AXI clock to the MHI bus while in L1 substates to save power
(Manivannan Sadhasivam)
- Disable Master AXI clock to save power when there is no traffic on PCIe
(Manivannan Sadhasivam)
- Make the "PERST separation" debug feature optional in the DT and the
driver (Manivannan Sadhasivam)
- Define clocks to be per-platform in DT to prepare for future SoCs
(Manivannan Sadhasivam)
- Add SM8450 SoC support (Manivannan Sadhasivam)
- Check for platform_get_resource_byname() to avoid a NULL pointer
dereference (Yang Yingliang)
* pci/qcom:
PCI: qcom-ep: Check platform_get_resource_byname() return value
PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Define clocks per platform
PCI: qcom-ep: Make PERST separation optional
dt-bindings: PCI: qcom-ep: Make PERST separation optional
PCI: qcom-ep: Disable Master AXI Clock when there is no PCIe traffic
PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SS
PCI: qcom-ep: Expose link transition counts via debugfs
PCI: qcom-ep: Disable IRQs during driver remove
PCI: qcom-ep: Make use of the cached dev pointer
PCI: qcom-ep: Rely on the clocks supplied by devicetree
PCI: qcom-ep: Add kernel-doc for qcom_pcie_ep structure
PCI: qcom: Rename host-init error label
PCI: qcom: Drop unused post_deinit callback
PCI: qcom-ep: Add MODULE_DEVICE_TABLE
PCI: qcom: Sort device-id table
PCI: qcom: Clean up IP configurations
PCI: qcom: Make all optional clocks optional
PCI: qcom: Add support for SA8540P
PCI: qcom: Add support for SC8280XP
dt-bindings: PCI: qcom: Add SA8540P to binding
dt-bindings: PCI: qcom: Add SC8280XP to binding
dt-bindings: PCI: qcom: Enumerate platforms with single msi interrupt
- Rename the pcie-mediatek-gen3 driver from 'mtk-pcie' to 'mtk-pcie-gen3'
so it can coexist with the pcie-mediatek driver, which also uses
'mtk-pcie' (Felix Fietkau)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek-gen3: Change driver name to mtk-pcie-gen3
- Use dmam_alloc_coherent() instead of dma_map_page() to allocate the MSI
target page, which means dwc drivers will work even when ZONE_DMA32 is
disabled (Will McVicker)
- If we can't allocate an MSI target page with a 32-bit address, try
allocating one with a 64-bit address (Will McVicker)
- Switch from of_gpio_named_count() to generic gpiod_count() (Andy
Shevchenko)
- Add support for i.MX8MP PCIe (Richard Zhu)
- Fix the Freescale i.MX8 PHY driver, which had interchanged the phy_init()
and phy_power_on() interfaces (Richard Zhu)
* remotes/lorenzo/pci/dwc:
phy: freescale: imx8m-pcie: Fix the wrong order of phy_init() and phy_power_on()
PCI: imx6: Add i.MX8MP PCIe support
PCI: dwc: Replace of_gpio_named_count() by gpiod_count()
PCI: dwc: Drop dependency on ZONE_DMA32
- In an emulated PCI bridge, set Capability offsets so they match the
hardware offsets shown by U-Boot (Pali Rohár)
* remotes/lorenzo/pci/bridge-emul:
PCI: pci-bridge-emul: Set position of PCI capabilities to real HW value
- Switch from gpiod_get_from_of_node() to generic devm GPIO API (Dmitry
Torokhov)
* remotes/lorenzo/pci/apple:
PCI: apple: Do not leak reset GPIO on unbind/unload/error
- Emulate the PCI Bridge Subsystem Vendor ID (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Add support for PCI Bridge Subsystem Vendor ID on emulated bridge
- Distribute resources to unconfigured hotplug bridges at boot-time (not
just when hot-adding such a bridge), which makes hot-adding devices to
docks work (Mika Westerberg)
- Fix the "revert to firmware assignment" code so we do the revert only if
the address is actually reachable. Previously we sometimes assigned
addresses that could not be reached via upstream bridges (Maciej W.
Rozycki)
* pci/resource:
PCI: Sanitise firmware BAR assignments behind a PCI-PCI bridge
PCI: Fix typo in pci_scan_child_bus_extend()
PCI: Fix whitespace and indentation
PCI: Distribute available resources for root buses, too
PCI: Move pci_assign_unassigned_root_bus_resources()
PCI: Pass available buses even if the bridge is already configured
PCI: Fix used_buses calculation in pci_scan_child_bus_extend()
- Expose a sysfs interface for configuring Resizable BARs so we can resize
BARs before assigning devices to a VM through VFIO (Alex Williamson)
* pci/rebar:
PCI: Expose PCIe Resizable BAR support via sysfs
- Cache the PTM capability offset instead of searching for it every time
(Bjorn Helgaas)
- Separate PTM configuration from PTM enable (Bjorn Helgaas)
- Add pci_suspend_ptm() and pci_resume_ptm() to disable and re-enable PTM
on suspend/resume so some Root Ports can safely enter a lower-power PM
state (Bjorn Helgaas)
- Disable PTM for all devices during suspend; previously we only did this
for Root Ports and even then only in certain cases (Bjorn Helgaas)
- Simplify pci_pm_suspend_noirq() (Rajvi Jingar)
- Reduce the delay after transitions to/from D3hot by using usleep_range()
instead of msleep(), which reduces the typical delay from 19ms to 10ms
(Sajid Dalvi, Will McVicker)
* pci/pm:
PCI/PM: Reduce D3hot delay with usleep_range()
PCI/PM: Simplify pci_pm_suspend_noirq()
PCI/PM: Always disable PTM for all devices during suspend
PCI/PTM: Consolidate PTM interface declarations
PCI/PTM: Reorder functions in logical order
PCI/PTM: Preserve RsvdP bits in PTM Control register
PCI/PTM: Move pci_ptm_info() body into its only caller
PCI/PTM: Add pci_suspend_ptm() and pci_resume_ptm()
PCI/PTM: Separate configuration and enable
PCI/PTM: Add pci_upstream_ptm() helper
PCI/PTM: Cache PTM Capability offset
- Correct a typo in 71020a3c0d ('PCI/MSI: Use msi_add_msi_desc()') that
reversed the sense of 'can_mask' in msi_add_msi_desc() (Josef Johansson)
* pci/msi:
PCI/MSI: Correct 'can_mask' test in msi_add_msi_desc()
- Work around a BIOS defect that makes some Intel Root Ports report an RP
PIO log size of zero (Mika Westerberg)
* pci/dpc:
PCI/DPC: Quirk PIO log size for certain Intel Root Ports
If platform_get_resource_byname() fails, 'mmio_res' will be set to NULL
pointer, which causes a NULL pointer dereference when it is used in
qcom_pcie_perst_deassert().
Check the return value to prevent it.
Link: https://lore.kernel.org/r/20220429080740.1294797-1-yangyingliang@huawei.com
Fixes: f55fee56a6 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Add support for SM8450 SoC to the Qualcomm PCIe Endpoint Controller
driver. The driver uses the same config as the existing SDX55 chipset,
so additional settings are not required.
Link: https://lore.kernel.org/r/20220914075350.7992-13-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PERST separation is an optional debug feature used to collect the crash
dump from the PCIe endpoint devices by the PCIe host when the endpoint
crashes. This feature keeps the PCIe link up by separating the PCIe IP
block from the SoC reset logic.
Make the property optional in the driver.
Link: https://lore.kernel.org/r/20220914075350.7992-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Master AXI clock can be disabled when it is not used i.e., when there
is no traffic on the PCIe bus. This helps to save power during idle state.
[bhelgaas: tidy and wrap comment]
Link: https://lore.kernel.org/r/20220914075350.7992-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a simple sysfs interface to Resizable BAR support, largely for the
purposes of assigning such devices to a VM through VFIO. Resizable BARs
present a difficult feature to expose to a VM through emulation, as
resizing a BAR is done on the host. It can fail, and often does, but we
have no means via emulation of a PCIe REBAR capability to handle the error
cases.
A vfio-pci specific ioctl interface is also cumbersome as there are often
multiple devices within the same bridge aperture and handling them is a
challenge. In the interface proposed here, expanding a BAR potentially
requires such devices to be soft-removed during the resize operation and
rescanned after, in order for all the necessary resources to be released.
A pci-sysfs interface is also more universal than a vfio specific
interface.
Please see the ABI documentation update for usage.
Link: https://lore.kernel.org/r/166336088796.3597940.14973499936692558556.stgit@omen
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: Krzysztof Wilczyński <kw@linux.com>
80d7d7a904 ("PCI/ASPM: Calculate LTR_L1.2_THRESHOLD from device
characteristics") replaced a fixed value (163840ns) with one computed from
T_POWER_OFF, Common_Mode_Restore_Time, etc., but it encoded the
LTR_L1.2_THRESHOLD value incorrectly.
This is especially a problem for small thresholds, e.g., 63ns fell into the
"threshold_ns < 1024" case and was encoded as 32ns:
LTR_L1.2_THRESHOLD_Scale = 1 (multiplier is 32ns)
LTR_L1.2_THRESHOLD_Value = 63 >> 5 = 1
LTR_L1.2_THRESHOLD = multiplier * value = 32ns * 1 = 32ns
Correct the algorithm to encode all times of 1023ns (0x3ff) or smaller
exactly and larger times conservatively (the encoded threshold is never
smaller than was requested). This reduces the chance of entering L1.2
when the device can't tolerate the exit latency.
Fixes: 80d7d7a904 ("PCI/ASPM: Calculate LTR_L1.2_THRESHOLD from device characteristics")
Link: https://lore.kernel.org/r/20221005025809.2247547-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
187f91db82 ("PCI/ASPM: Remove struct aspm_register_info.l1ss_cap")
inadvertently removed a check for existence of the L1 PM Substates (L1SS)
Capability before reading it.
If there is no L1SS Capability, this means we mistakenly read PCI_COMMAND
and PCI_STATUS (config address 0x04) and interpret that as the PCI_L1SS_CAP
register, so we may incorrectly configure L1SS.
Make sure the L1SS Capability exists before trying to read it.
Fixes: 187f91db82 ("PCI/ASPM: Remove struct aspm_register_info.l1ss_cap")
Link: https://lore.kernel.org/r/20221005025809.2247547-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Qualcomm PCIe controllers have debug registers in the MMIO region
that count PCIe link transitions. Expose them over debugfs to
userspace to help debug the low power issues.
Link: https://lore.kernel.org/r/20220914075350.7992-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Disable the Global and PERST IRQs during driver remove to avoid getting
spurious IRQs after resource deallocation.
Link: https://lore.kernel.org/r/20220914075350.7992-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Previously the L1 PM Substates Control Registers (CTL1 and CTL2) weren't
saved and restored during suspend/resume leading to the L1 PM Substates
configuration being lost post-resume.
Save the L1 PM Substates Control Registers so that the configuration is
retained post-resume.
[bhelgaas: drop pci_is_pcie() testing; we can rely on pci_configure_ltr()
having already done that]
Link: https://lore.kernel.org/r/20220913131822.16557-3-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
An HVM guest with linux stubdomain and 2 PCI devices failed to start as
libxl timed out waiting for the PCI devices to be added. It happens
intermittently but with some regularity. libxl wrote the two xenstore
entries for the devices, but then timed out waiting for backend state 4
(Connected) - the state stayed at 7 (Reconfiguring). (PCI passthrough
to an HVM with stubdomain is PV passthrough to the stubdomain and then
HVM passthrough with the QEMU inside the stubdomain.)
The stubdomain kernel never printed "pcifront pci-0: Installing PCI
frontend", so it seems to have missed state 4 which would have
called pcifront_try_connect() -> pcifront_connect_and_init_dma()
Have pcifront_detach_devices() special-case state Initialised and call
pcifront_connect_and_init_dma(). Don't use pcifront_try_connect()
because that sets the xenbus state which may throw off the backend.
After connecting, skip the remainder of detach_devices since none have
been initialized yet. When the backend switches to Reconfigured,
pcifront_attach_devices() will pick them up again.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220829151536.8578-1-jandryuk@gmail.com
Signed-off-by: Juergen Gross <jgross@suse.com>
In the qcom_pcie_ep_get_resources() function, dev pointer is already
cached in a local variable. So let's make use of it instead of getting
the dev pointer again from pdev struct.
Link: https://lore.kernel.org/r/20220914075350.7992-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Generally, device drivers should just rely on the platform data like
devicetree to supply the clocks required for the functioning of the
peripheral. There is no need to hardcode the clk info in the driver.
So get rid of the static clk info and obtain the platform supplied
clks.
The total number of clocks supplied is obtained using the
devm_clk_bulk_get_all() API and used for the rest of the clk_bulk_ APIs.
Link: https://lore.kernel.org/r/20220914075350.7992-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Refer to phy_core driver, phy_init() must be called before phy_power_on().
Fix the wrong order of phy_init() and phy_power_on() here.
Link: https://lore.kernel.org/r/1662344583-18874-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 1aa97b0022 ("phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Add i.MX8MP PCIe support.
To avoid codes duplication when find the syscon regmap, add the iomux
gpr syscon compatible into drvdata.
Link: https://lore.kernel.org/r/1662109086-15881-8-git-send-email-hongxing.zhu@nxp.com
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
As a preparation to unexport of_gpio_named_count(), convert the
driver to use gpiod_count() instead.
Link: https://lore.kernel.org/r/20220830183310.48541-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
PCIe r6.0, sec 5.9, requires a 10ms delay between programming a device to
change to or from D3hot and the time the device is next accessed (unless
Readiness Notifications are used).
The 10ms value (PCI_PM_D3HOT_WAIT) doesn't appear directly here because
some chipsets require 120ms for devices *below* them (pci_pm_d3hot_delay)
and some devices require more or less than 10ms (dev->d3hot_delay).
But msleep(10) typically waits about *20*ms, which is more than we need.
Switch to usleep_range() to improve the delay accuracy.
Based on a commit from Sajid in the Pixel 6 kernel tree [1]. On a Pixel 6,
the 10ms delay for the Exynos PCIe device delayed for an average of 19ms.
Switching to usleep_range() decreased the resume time by about 9ms.
[1] 18a8cad68d
[bhelgaas commit log, add timers-howto.rst link]
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/timers/timers-howto.rst?id=v5.19#n73
Link: https://lore.kernel.org/r/20220921212735.2131588-1-willmcvicker@google.com
Signed-off-by: Sajid Dalvi <sdalvi@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Drop the unused and confusingly named post_deinit callback that was
added for the now removed pipe clock handling.
If ever needed we can add back a callback named pre_deinit (or perhaps
rather pre_phy_power_off) instead.
Link: https://lore.kernel.org/r/20220928155421.21660-2-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Some Root Ports on Intel Tiger Lake and Alder Lake systems support the RP
Extensions for DPC and the RP PIO Log registers but incorrectly advertise
an RP PIO Log Size of zero. This means the kernel complains that:
DPC: RP PIO log size 0 is invalid
and if DPC is triggered, the DPC driver will not dump the RP PIO Log
registers when it should.
This is caused by a BIOS bug and should be fixed the BIOS for future CPUs.
Add a quirk to set the correct RP PIO Log size for the affected Root Ports.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209943
Link: https://lore.kernel.org/r/20220816102042.69125-1-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Simplify pci-ftpci100.c driver code and use new PCI_CONF1_ADDRESS() macro
for accessing PCI config space.
Link: https://lore.kernel.org/r/20220924092404.31776-3-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Lot of PCI and PCIe controllers are using standard Config Address for PCI
Configuration Mechanism #1 (as defined in PCI Local Bus Specification) or
its extended version.
So introduce new macros PCI_CONF1_ADDRESS() and PCI_CONF1_EXT_ADDRESS() in
include file drivers/pci/pci.h which can be suitable for PCI and PCIe
controllers which uses this type of access to PCI config space.
Link: https://lore.kernel.org/r/20220924092404.31776-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
When pci_assign_resource() is unable to assign resources to a BAR, it uses
pci_revert_fw_address() to fall back to a firmware assignment (if any).
Previously pci_revert_fw_address() assumed all addresses could reach the
device, but this is not true if the device is below a bridge that only
forwards addresses within its windows.
This problem was observed on a Tyan Tomcat IV S1564D system where the BIOS
did not assign valid addresses to several bridges and USB devices:
pci 0000:00:11.0: PCI-to-PCIe bridge to [bus 01-ff]
pci 0000:00:11.0: bridge window [io 0xe000-0xefff]
pci 0000:01:00.0: PCIe Upstream Port to [bus 02-ff]
pci 0000:01:00.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:02:02.0: PCIe Downstream Port to [bus 05-ff]
pci 0000:02:02.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:05:00.0: PCIe-to-PCI bridge to [bus 06-ff]
pci 0000:05:00.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:06:08.0: USB UHCI 1.1
pci 0000:06:08.0: BAR 4: [io 0xfce0-0xfcff] # unreachable
pci 0000:06:08.1: USB UHCI 1.1
pci 0000:06:08.1: BAR 4: [io 0xfce0-0xfcff] # unreachable
pci 0000:06:08.0: can't claim BAR 4 [io 0xfce0-0xfcff]: no compatible bridge window
pci 0000:06:08.1: can't claim BAR 4 [io 0xfce0-0xfcff]: no compatible bridge window
During the first pass of assigning unassigned resources, there was not
enough I/O space available, so we couldn't assign the 06:08.0 BAR and
reverted to the firmware assignment (still unreachable). Reverting the
06:08.1 assignment failed because it conflicted with 06:08.0:
pci 0000:00:11.0: bridge window [io 0xe000-0xefff]
pci 0000:01:00.0: no space for bridge window [io size 0x2000]
pci 0000:02:02.0: no space for bridge window [io size 0x1000]
pci 0000:05:00.0: no space for bridge window [io size 0x1000]
pci 0000:06:08.0: BAR 4: no space for [io size 0x0020]
pci 0000:06:08.0: BAR 4: trying firmware assignment [io 0xfce0-0xfcff]
pci 0000:06:08.1: BAR 4: no space for [io size 0x0020]
pci 0000:06:08.1: BAR 4: trying firmware assignment [io 0xfce0-0xfcff]
pci 0000:06:08.1: BAR 4: [io 0xfce0-0xfcff] conflicts with 0000:06:08.0 [io 0xfce0-0xfcff]
A subsequent pass assigned valid bridge windows and a valid 06:08.1 BAR,
but left the 06:08.0 BAR alone, so the UHCI device was still unusable:
pci 0000:00:11.0: bridge window [io 0xe000-0xefff] released
pci 0000:00:11.0: bridge window [io 0x1000-0x2fff] # reassigned
pci 0000:01:00.0: bridge window [io 0x1000-0x2fff] # reassigned
pci 0000:02:02.0: bridge window [io 0x2000-0x2fff] # reassigned
pci 0000:05:00.0: bridge window [io 0x2000-0x2fff] # reassigned
pci 0000:06:08.0: BAR 4: assigned [io 0xfce0-0xfcff] # left alone
pci 0000:06:08.1: BAR 4: assigned [io 0x2000-0x201f]
...
uhci_hcd 0000:06:08.0: host system error, PCI problems?
uhci_hcd 0000:06:08.0: host controller process error, something bad happened!
uhci_hcd 0000:06:08.0: host controller halted, very bad!
uhci_hcd 0000:06:08.0: HCRESET not completed yet!
uhci_hcd 0000:06:08.0: HC died; cleaning up
If the address assigned by firmware is not reachable because it's not
within upstream bridge windows, fail instead of assigning the unusable
address from firmware.
[bhelgaas: commit log, use pci_upstream_bridge()]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=16263
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2203012338460.46819@angie.orcam.me.uk
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209211921250.29493@angie.orcam.me.uk
Fixes: 58c84eda07 ("PCI: fall back to original BIOS BAR addresses")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.35+
Drop two empty lines from pci_scan_child_bus_extend() and correct
indentation in pci_bridge_distribute_available_resources() to better
follow the kernel coding style.
No functional impact.
Link: https://lore.kernel.org/r/20220905080232.36087-6-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Previously we distributed spare resources only upon hot-add, so if the
initial root bus scan found devices that had not been fully configured by
the BIOS, we allocated only enough resources to cover what was then
present. If some of those devices were hotplug bridges, we did not leave
any additional resource space for future expansion.
Distribute the available resources for root buses, too, to make this work
the same way as the normal hotplug case.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216000
Link: https://lore.kernel.org/r/20220905080232.36087-5-mika.westerberg@linux.intel.com
Reported-by: Chris Chiu <chris.chiu@canonical.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We need to be able to call pci_bridge_distribute_available_resources()
from this function so move it accordingly to avoid need for forward
declaration.
No functional impact.
Link: https://lore.kernel.org/r/20220905080232.36087-4-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
If some part of the PCI topology is already configured (by the boot
firmware) but not all, and it includes hotplug bridges, we may need to
extend the bus resources of those bridges to accommodate any future
hotplugs, in the same way we already do with the normal hotplug case.
Pass the available buses to pci_scan_child_bus_extend() even when the
bridge in question is already configured so the bus allocation code can use
these available buses to extend the possible hotplug bridges below.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216000
Link: https://lore.kernel.org/r/20220905080232.36087-3-mika.westerberg@linux.intel.com
Reported-by: Chris Chiu <chris.chiu@canonical.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
pci_scan_bridge_extend() returns the subordinate bus number needed to cover
all the buses below a bridge. pci_scan_child_bus_extend() computes the
number of buses to reserve by comparing that with the current max bus
number. Previously it did the subtraction in the wrong order, so
'used_buses' was nonsense.
Subtract 'max' from 'cmax' as is done for the similar
pci_scan_bridge_extend() call in the following block.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216000
Fixes: 3374c545c2 ("PCI: Account for all bridges on bus when distributing bus numbers")
Link: https://lore.kernel.org/r/20220905080232.36087-2-mika.westerberg@linux.intel.com
Reported-by: Chris Chiu <chris.chiu@canonical.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Use for_each_pci_dev() instead of open-coding it. No functional change.
Link: https://lore.kernel.org/r/20220916140329.679633-1-yangyingliang@huawei.com
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Register with Subsystem Device/Vendor ID is at offset 0x2c.
Export it via the emulated bridge to enable support for the Subsystem
Device/Vendor ID - by reading it in the PCI controller config space and
storing it in the emulated bridge control structures, so that it is
exposed in the respective PCI capability.
After this change Subsystem ID is visible in lspci output at line:
Capabilities: [40] Subsystem
Link: https://lore.kernel.org/r/20220711225915.13896-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
The driver allocates reset GPIO in apple_pcie_setup_port() but neither
releases the resource, nor uses devm API to have it released
automatically.
Let's fix this by switching to devm API. While at it let's use generic
devm_fwnode_gpiod_get() instead of OF-specific gpiod_get_from_of_node()
- this will allow us top stop exporting the latter down the road.
Link: https://lore.kernel.org/r/YxatO5OaI2RpxQ2M@google.com
Fixes: 1e33888fbe ("PCI: apple: Add initial hardware bring-up")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Hector Martin <marcan@marcan.st>
Acked-by: Marc Zyngier <maz@kernel.org>
We always want to save the device state unless the driver has already done
it. Rearrange the checking in pci_pm_suspend_noirq() to make this more
clear. No functional change intended.
[bhelgaas: commit log, rewrap comment]
Link: https://lore.kernel.org/r/20220830104913.1620539-1-rajvi.jingar@linux.intel.com
Signed-off-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We want to disable PTM on Root Ports because that allows some chips, e.g.,
Intel mobile chips since Coffee Lake, to enter a lower-power PM state.
That means we also have to disable PTM on downstream devices. PCIe r6.0,
sec 2.2.8, recommends that functions support generation of messages in
non-D0 states, so we have to assume Switch Upstream Ports or Endpoints may
send PTM Requests while in D1, D2, and D3hot. A PTM message received by a
Downstream Port (including a Root Port) with PTM disabled must be treated
as an Unsupported Request (sec 6.21.3).
PTM was previously disabled only for Root Ports, and it was disabled in
pci_prepare_to_sleep(), which is not called at all if a driver supports
legacy PM or does its own state saving.
Instead, disable PTM early in pci_pm_suspend() and pci_pm_runtime_suspend()
so we do it in all cases.
Previously PTM was disabled *after* saving device state, so the state
restore on resume automatically re-enabled it. Since we now disable PTM
*before* saving state, we must explicitly re-enable it in pci_pm_resume()
and pci_pm_runtime_resume().
Here's a sample of errors that occur when PTM is disabled only on the Root
Port. With this topology:
0000:00:1d.0 Root Port to [bus 08-71]
0000:08:00.0 Switch Upstream Port to [bus 09-71]
Kai-Heng reported errors like this:
pcieport 0000:00:1d.0: [20] UnsupReq (First)
pcieport 0000:00:1d.0: AER: TLP Header: 34000000 08000052 00000000 00000000
Decoding TLP header 0x34...... (0011 0100b) and 0x08000052:
Fmt 001b 4 DW header, no data
Type 1 0100b Msg (Local - Terminate at Receiver)
Requester ID 0x0800 Bus 08 Devfn 00.0
Message Code 0x52 0101 0010b PTM Request
The 00:1d.0 Root Port logged an Unsupported Request error when it received
a PTM Request with Requester ID 08:00.0.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=215453
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=216210
Fixes: a697f072f5 ("PCI: Disable PTM during suspend to save power")
Link: https://lore.kernel.org/r/20220909202505.314195-10-helgaas@kernel.org
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Consolidate all the PTM-related declarations in drivers/pci/pci.h. No
functional change intended.
Link: https://lore.kernel.org/r/20220909202505.314195-9-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
pci_enable_ptm() and pci_disable_ptm() were separated.
pci_save_ptm_state() and pci_restore_ptm_state() dangled at the top. Move
them to logical places. No functional change intended.
Link: https://lore.kernel.org/r/20220909202505.314195-8-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Even though only the low 16 bits of PTM Control are currently defined, the
register is 32 bits wide and the unused bits are RsvdP ("Reserved and
Preserved"), so software must preserve the values of those bits when
writing the register.
Update PTM Control reads and writes to use 32-bit accesses and preserve the
reserved bits on writes.
Link: https://lore.kernel.org/r/20220909202505.314195-7-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
pci_ptm_info() is simple and is only called by pci_enable_ptm(). Move the
entire body there. No functional change intended.
Link: https://lore.kernel.org/r/20220909202505.314195-6-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We disable PTM during suspend because that allows some Root Ports to enter
lower-power PM states, which means we also need to disable PTM for all
downstream devices. Add pci_suspend_ptm() and pci_resume_ptm() for this
purpose.
pci_enable_ptm() and pci_disable_ptm() are for drivers to use to enable or
disable PTM. They use dev->ptm_enabled to keep track of whether PTM should
be enabled.
pci_suspend_ptm() and pci_resume_ptm() are PCI core-internal functions to
temporarily disable PTM during suspend and (depending on dev->ptm_enabled)
re-enable PTM during resume.
Enable/disable/suspend/resume all use internal __pci_enable_ptm() and
__pci_disable_ptm() functions that only update the PTM Control register.
Outline:
pci_enable_ptm(struct pci_dev *dev)
{
__pci_enable_ptm(dev);
dev->ptm_enabled = 1;
pci_ptm_info(dev);
}
pci_disable_ptm(struct pci_dev *dev)
{
if (dev->ptm_enabled) {
__pci_disable_ptm(dev);
dev->ptm_enabled = 0;
}
}
pci_suspend_ptm(struct pci_dev *dev)
{
if (dev->ptm_enabled)
__pci_disable_ptm(dev);
}
pci_resume_ptm(struct pci_dev *dev)
{
if (dev->ptm_enabled)
__pci_enable_ptm(dev);
}
Nothing currently calls pci_resume_ptm(); the suspend path saves the PTM
state before disabling PTM, so the PTM state restore in the resume path
implicitly re-enables it. A future change will use pci_resume_ptm() to fix
some problems with this approach.
Link: https://lore.kernel.org/r/20220909202505.314195-5-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
PTM configuration and enabling were previously mixed together:
pci_ptm_init() collected granularity info and enabled PTM for Root Ports
and Switch Upstream Ports; pci_enable_ptm() did the same for Endpoints.
Move everything related to the PTM Capability register to pci_ptm_init()
for all devices, and everything related to the PTM Control register to
pci_enable_ptm().
Link: https://lore.kernel.org/r/20220909202505.314195-4-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
PTM requires an unbroken path of PTM-supporting devices between the PTM
Root and the ultimate PTM Requester, but if a Switch supports PTM, only the
Upstream Port can have a PTM Capability; the Downstream Ports do not.
Previously we copied the PTM configuration from the Switch Upstream Port to
the Downstream Ports so dev->ptm_enabled for any device implied that all
the upstream devices support PTM.
Instead of making it look like Downstream Ports have their own PTM config,
add pci_upstream_ptm(), which returns the upstream device that has a PTM
Capability (either a Root Port or a Switch Upstream Port).
Link: https://lore.kernel.org/r/20220909202505.314195-3-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cache the PTM Capability offset instead of searching for it every time we
enable/disable PTM or save/restore PTM state. No functional change
intended.
Link: https://lore.kernel.org/r/20220909202505.314195-2-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Re-work the msi_msg DMA allocation logic to use dmam_alloc_coherent() which
uses the coherent DMA mask to try to return an allocation within the DMA
mask limits. With that, we now can drop the msi_page parameter in struct
dw_pcie_rp. This allows kernel configurations that disable ZONE_DMA32 to
continue supporting a 32-bit DMA mask. Without this patch, the PCIe host
device will fail to probe when ZONE_DMA32 is disabled.
Link: https://lore.kernel.org/r/20220825235404.4132818-2-willmcvicker@google.com
Fixes: 35797e672f ("PCI: dwc: Fix MSI msi_msg DMA mapping")
Reported-by: Isaac J. Manjarres <isaacmanjarres@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
71020a3c0d ("PCI/MSI: Use msi_add_msi_desc()") inadvertently reversed
the sense of "msi_attrib.can_mask" in one use:
- if (entry->pci.msi_attrib.can_mask) {
- addr = pci_msix_desc_addr(entry);
- entry->pci.msix_ctrl = readl(addr + PCI_MSIX_ENTRY_VECTOR_CTRL);
+ if (!desc.pci.msi_attrib.can_mask) {
+ addr = pci_msix_desc_addr(&desc);
+ desc.pci.msix_ctrl = readl(addr + PCI_MSIX_ENTRY_VECTOR_CTRL);
Restore the original test.
[bhelgaas: commit log]
Fixes: 71020a3c0d ("PCI/MSI: Use msi_add_msi_desc()")
Link: https://lore.kernel.org/r/d818f9c9-a432-213e-4152-eaff3b7da52e@oderland.se
Signed-off-by: Josef Johansson <josef@oderland.se>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
mvebu and aardvark HW have PCIe capabilities on different offset in PCI
config space. Extend pci-bridge-emul.c code to allow setting custom driver
custom value where PCIe capabilities starts.
With this change PCIe capabilities of both drivers are reported at the same
location as where they are reported by U-Boot - in their real HW offset.
Link: https://lore.kernel.org/r/20220824112124.21675-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
