Due to a hardware bug, the originally assigned range cannot reliably
be used for boot configuration and must not be modifiable through
ethtool.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
FALCON_SPI_MAX_LEN has type size_t while other SPI lengths have type
unsigned int. This results in warnings from min() on 64-bit
architectures where they are different. Add a cast to make it match.
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For some buffers we use a starting offset of either NET_IP_ALIGN or 0
depending on whether we believe the architecture supports efficient
access to unaligned words. There is now a config macro specifying
whether this is the case, so check that rather than checking for
specific architectures.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This should avoid an interrupt storm, which has been observed in the
field with one faulty board.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This prevents speculative reading of the statistics before the
completion flag.
From: Neil Turton <nturton@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
mdio_clause45_links_ok() correctly checks efx_phy_mode_disabled(), so
tenxpress_link_ok() doesn't need to.
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Increase the potential retry count for RX flushes from 5 to 100.
Stop polling the RX_DESC_PTR_TBL to infer that a flush might have
happened. Instead absolutely rely on the flush events, unless bug 7803
applies (Falcon rev A only).
To keep things quick, request flushes for every TX and RX queue up
front, and match up the events to requests.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On some boards 10Xpress feeds a 156 MHz clock to the Falcon XMAC. MAC
statistics DMA can fail while this clock is stopped during a PHY reset.
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There was a bug in XAUI synchronisation in early 10Xpress firmware
versions. This is fixed in released firmware and we do not need to
work around it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Match pci_request_region() with pci_release_region(), not
release_mem_region().
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When !port_enabled, defer the write to reconfigure_mac_wrapper.
Whilst here, simplify the logic now that efx_start_port() always calls
efx_reconfigure_port().
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This was originally a kludge to fix broken locking, which has since
been fixed properly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Include PMA/PMD in loopback self-tests as intended.
Add NVRAM checksum validation and include it in self-tests.
Add register self-tests.
Run PHY self-tests where available.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This will support register self-tests.
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Move more code from efx_reset() into efx_reset_down() and efx_reset_up().
Stop propagating MAC/PHY setting failures from efx_reset_down() and
efx_reset_up() as these should not be fatal.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some functions return an error code which is always 0. Change their
return types to void and simplify their callers accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Update comment on the dummy operation implementations.
Line up the board operation initialisers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This allows updating PHY firmware for one interface without removing
all other interfaces handled by the driver.
Replace tx_disabled flags and 10Xpress status enumeration with flags in
enum efx_phy_mode.
Prevent an interface from being brought up while in PHY flash mode.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make efx_process_channel() and falcon_process_eventq() return the
number of packets received rather than updating the quota, consistent
with new NAPI.
Since channels and RX queues are mapped one-to-one, remove return
value from falcon_handle_rx_event() and add a warning for events
with the wrong RX queue number.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently each channel can have at most one RX queue, so go straight to
that one.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We have long since given up doing RSS on Falcon A1 and therefore we
would always write the default value of 0.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rename efx_nic::rss_queues to the more obvious n_rx_queues
Remove efx_rx_queue::used and other stuff that's redundant with it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
efx_channel::has_interrupt is redundant with efx_channel::used_flags.
Remove efx_test_eventq() because it is now obviously unreachable.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Extend the SPI device setup code to support this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
gcc will automatically inline static functions with only one caller, and
may inline other functions depending on the kernel configuration and size
of the intermediate code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Squashed nested structures.
Renamed remaining_len to out_len, ifc.len to in_len, header_length to
header_len.
Moved ipv4_id into the group of output variables where it belongs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Replace (cond ? 1 : 0) with cond or !!cond as appropriate, and
(cond ? 0 : 1) with !cond.
Remove some redundant boolean temporaries.
Rename one field that looks like a flag but isn't.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove unmap_addr since it can be calculated from dma_addr, len and
unmap_len. This saves 4-16 bytes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add efx_poll_loopback() function to test for successful completion of test.
Change efx_test_loopback() to end the test after 1 ms if
efx_poll_loopback() indicates success, and otherwise to wait for 100 ms
as before.
While we're here, rename efx_{rx,tx}_loopback() to
efx_{begin,end}_loopback() which more accurately reflect their
purpose.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Removed log messages that are redundant with calling functions.
Fixed bitwise or-ing of return codes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This was making noise during 10Xpress self-test.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
These were clearly bogus.
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Exclude assumed size of RX control frames from rx_bad_bytes.
Exclude assumed size of TX control frames from tx_good_bytes for
consistency with rx_good_bytes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We believed that some valid SNAP frames were being marked as invalid.
In fact this is not the case and no workaround is needed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently the board initialisation includes 2 delays of 1 second each.
Usually it is unnecessary to wait that long, so check before doing so.
Correct some of the comments and log messages while we're here.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
efx_test_loopback() used "|" to combine the results of the RX and TX
phases. If both phases fail with different error codes, this results
in a bogus error code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
