* pci/host-imx6:
PCI: imx6: Fix bugs in PCIe startup code
PCI: imx6: Start link in Gen1 before negotiating for Gen2 mode
PCI: imx6: Factor out link up wait loop
PCI: imx6: Factor out PHY reset
PCI: imx6: Report "link up" only after link training completes
PCI: imx6: Make reset-gpio optional
pp->io_base, which is the input of the outbound IO address translation
unit, should be the CPU address. It was incorrectly programmed to the
realio address.
We should pass global_io_offset rather than sys->io_offset to
pci_ioremap_io(), so we map the new window into the first available spot in
the Linux view of the I/O space.
We must also pass CPU address instead of realio address to pci_ioremap_io().
This patch fixes above issue. It has been tested with Lecroy PTC in AIC
mode and Pericom PI7C9X2G303EL PCIe switch, which does not work otherwise.
Tested-by: Mohit Kumar <mohit.kumar@st.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marek Vasut <marex@denx.de
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Zhu <Hong-Xing.Zhu@freescale.com>
The cfg_read/write functions are DesignWare-specific. Add dw_pcie prefix
to avoid collision in global name space.
Tested-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
The interrupts were cleared after the IRQ handler was called. This means
that new interrupts that occur after the handler handled the previous IRQ
but before the interrupt is cleared will be missed.
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Matthias Mann <m.mann@arkona-technologies.de>
Signed-off-by: Harro Haan <hrhaan@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mohit Kumar <mohit.kumar@st.com>
Cc: Richard Zhu <hong-xing.zhu@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Juergen Beisert <jbe@pengutronix.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Sean Cross <xobs@kosagi.com>
Previously pcie_device_init() called get_device() if device_register() for
the new pcie_device succeeded, and remove_iter() called put_device() when
removing before unregistering the device.
But device_register() already increments the reference count in
device_add(), so we don't need to do it again here.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This is required so that we give up the last reference to the device.
Removed the kfree() as put_device will result in release_pcie_device()
being called and hence the container of the device will be kfree'd.
[bhelgaas: fix conflict after my previous cleanup]
Signed-off-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make the straightline path the normal no-error path. Check for errors and
return them directly, instead of checking for success and putting the
normal path in an "if" body.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
mvebu_pcie_of_match_table is always compiled in. Hence of_match_ptr is not
required.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch first forces the link into Gen1 mode before starting up the link
and, only after the link is up, start negotiating possible Gen2 mode
operation. This is because without such sequence, some PCIe switches are
not detected at all.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Split the function that waits for the PCIe link to come up from the rest if
the host init function. We will find this change useful in the subsequent
patch, since this will be called twice then.
No functional change.
[bhelgaas: remove useless "return;"]
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Split the PCIe PHY reset from the link up function to make the code a
little more structured.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
While waiting for the PHY to report the PCIe link is up, we might hit a
situation where the link training is still in progress, while the PHY
already reports the link is up. Add additional check for this condition.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Some boards do not have a PCIe reset GPIO. To avoid probe failure on these
boards, make the reset GPIO optional as well.
[bhelgaas: whitespace fixes]
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
* pci/vc:
PCI: Rename PCI_VC_PORT_REG1/2 to PCI_VC_PORT_CAP1/2
PCI: Add Virtual Channel to save/restore support
PCI: Add support for save/restore of extended capabilities
PCI: Add pci_wait_for_pending() (refactor pci_wait_for_pending_transaction())
* pci/host-mvebu:
PCI: mvebu: Remove duplicate of_clk_get_by_name() call
PCI: mvebu: Support a bridge with no IO port window
PCI: mvebu: Obey bridge PCI_COMMAND_MEM and PCI_COMMAND_IO bits
PCI: mvebu: Drop writes to bridge Secondary Status register
* pci/deletion:
PCI: Remove from bus_list and release resources in pci_release_dev()
PCI: Move pci_proc_attach_device() to pci_bus_add_device()
PCI: Use device_release_driver() in pci_stop_root_bus()
PCI: Move device_del() from pci_stop_dev() to pci_destroy_dev()
Conflicts:
drivers/pci/remove.c
Previously we removed the pci_dev from the bus_list and released its
resources in pci_destroy_dev(). But that's too early: it's possible to
call pci_destroy_dev() twice for the same device (e.g., via sysfs), and
that will cause an oops when we try to remove it from bus_list the second
time.
We should remove it from the bus_list only when the last reference to the
pci_dev has been released, i.e., in pci_release_dev().
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
4f535093cf ("PCI: Put pci_dev in device tree as early as possible")
moved pci_proc_attach_device() from pci_bus_add_device() to
pci_device_add().
This moves it back to pci_bus_add_device(), essentially reverting that
part of 4f535093cf. This makes it symmetric with pci_stop_dev(),
where we call pci_proc_detach_device() and pci_remove_sysfs_dev_files()
and set dev->is_added = 0.
[bhelgaas: changelog, create sysfs then attach proc for symmetry]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
To be consistent with 4bff674990 ("PCI: Move device_del() from
pci_stop_dev() to pci_destroy_dev()", this changes pci_stop_root_bus()
to use device_release_driver() instead of device_del().
This also changes pci_remove_root_bus() to use device_unregister()
instead of put_device() so it corresponds with the device_register()
call in pci_create_root_bus().
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit bcdde7e221 (sysfs: make __sysfs_remove_dir() recursive)
I'm seeing traces analogous to the one below in Thunderbolt testing:
WARNING: CPU: 3 PID: 76 at /scratch/rafael/work/linux-pm/fs/sysfs/group.c:214 sysfs_remove_group+0x59/0xe0()
sysfs group ffffffff81c6c500 not found for kobject '0000:08'
Modules linked in: ...
CPU: 3 PID: 76 Comm: kworker/u16:7 Not tainted 3.13.0-rc1+ #76
Hardware name: Acer Aspire S5-391/Venus , BIOS V1.02 05/29/2012
Workqueue: kacpi_hotplug acpi_hotplug_work_fn
0000000000000009 ffff8801644b9ac8 ffffffff816b23bf 0000000000000007
ffff8801644b9b18 ffff8801644b9b08 ffffffff81046607 ffff88016925b800
0000000000000000 ffffffff81c6c500 ffff88016924f928 ffff88016924f800
Call Trace:
[<ffffffff816b23bf>] dump_stack+0x4e/0x71
[<ffffffff81046607>] warn_slowpath_common+0x87/0xb0
[<ffffffff810466d1>] warn_slowpath_fmt+0x41/0x50
[<ffffffff811e42ef>] ? sysfs_get_dirent_ns+0x6f/0x80
[<ffffffff811e5389>] sysfs_remove_group+0x59/0xe0
[<ffffffff8149f00b>] dpm_sysfs_remove+0x3b/0x50
[<ffffffff81495818>] device_del+0x58/0x1c0
[<ffffffff814959c8>] device_unregister+0x48/0x60
[<ffffffff813254fe>] pci_remove_bus+0x6e/0x80
[<ffffffff81325548>] pci_remove_bus_device+0x38/0x110
[<ffffffff8132555d>] pci_remove_bus_device+0x4d/0x110
[<ffffffff81325639>] pci_stop_and_remove_bus_device+0x19/0x20
[<ffffffff813418d0>] disable_slot+0x20/0xe0
[<ffffffff81341a38>] acpiphp_check_bridge+0xa8/0xd0
[<ffffffff813427ad>] hotplug_event+0x17d/0x220
[<ffffffff81342880>] hotplug_event_work+0x30/0x70
[<ffffffff8136d665>] acpi_hotplug_work_fn+0x18/0x24
[<ffffffff81061331>] process_one_work+0x261/0x450
[<ffffffff81061a7e>] worker_thread+0x21e/0x370
[<ffffffff81061860>] ? rescuer_thread+0x300/0x300
[<ffffffff81068342>] kthread+0xd2/0xe0
[<ffffffff81068270>] ? flush_kthread_worker+0x70/0x70
[<ffffffff816c19bc>] ret_from_fork+0x7c/0xb0
[<ffffffff81068270>] ? flush_kthread_worker+0x70/0x70
(Mika Westerberg sees them too in his tests).
Some investigation documented in kernel bug #65281 led me to the
conclusion that the source of the problem is the device_del() in
pci_stop_dev() as it now causes the sysfs directory of the device to be
removed recursively along with all of its subdirectories. That includes
the sysfs directory of the device's subordinate bus (dev->subordinate) and
its "power" group.
Consequently, when pci_remove_bus() is called for dev->subordinate in
pci_remove_bus_device(), it calls device_unregister(&bus->dev), but at this
point the sysfs directory of bus->dev doesn't exist any more and its
"power" group doesn't exist either. Thus, when dpm_sysfs_remove() called
from device_del() tries to remove that group, it triggers the above
warning.
That indicates a logical mistake in the design of
pci_stop_and_remove_bus_device(), which causes bus device objects to be
left behind their parents (bridge device objects) and can be fixed by
moving the device_del() from pci_stop_dev() into pci_destroy_dev(), so
pci_remove_bus() can be called for the device's subordinate bus before the
device itself is unregistered from the hierarchy. Still, the driver, if
any, should be detached from the device in pci_stop_dev(), so use
device_release_driver() directly from there.
References: https://bugzilla.kernel.org/show_bug.cgi?id=65281#c6
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These are set of two capability registers, it's pretty much given that
they're registers, so reflect their purpose in the name.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
While we don't really have any infrastructure for making use of VC
support, the system BIOS can configure the topology to non-default
VC values prior to boot. This may be due to silicon bugs, desire to
reserve traffic classes, or perhaps just BIOS bugs. When we reset
devices, the VC configuration may return to default values, which can
be incompatible with devices upstream. For instance, Nvidia GRID
cards provide a PCIe switch and some number of GPUs, all supporting
VC. The power-on default for VC is to support TC0-7 across VC0,
however some platforms will only enable TC0/VC0 mapping across the
topology. When we do a secondary bus reset on the downstream switch
port, the GPU is reset to a TC0-7/VC0 mapping while the opposite end
of the link only enables TC0/VC0. If the GPU attempts to use TC1-7,
it fails.
This patch attempts to provide complete support for VC save/restore,
even beyond the minimally required use case above. This includes
save/restore and reload of the arbitration table, save/restore and
reload of the port arbitration tables, and re-enabling of the
channels for VC, VC9, and MFVC capabilities.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Current save/restore is specific to standard capabilities.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We currently have two instance of this loop which waits for a pending bit
to clear in a status dword. Generalize the function for future users.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously, the caller checked ATTN_LED() or PWR_LED() to see whether the
slot has indicators before setting the indicator state. That clutters the
caller unnecessarily, so this moves the test inside the callees. The test
may not even be necessary; per spec it should be harmless to try to turn on
a non-existent LED. But checking first does avoid unnecessary hotplug
commands.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add symbolic constants for the PCIe Slot Control indicator and power
control fields defined by spec and use them instead of open-coded hex
constants.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It's simpler to test the PCI_EXP_SLTSTA_PFD bit directly and to write the
constant back to PCI_EXP_SLTSTA.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We already have the vendor/device IDs from pci_setup_device(), so drop that
info and print things that will be more useful for debugging: the slot
number and presence of button/indicators/link active reporting/etc.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These functions:
pcie_enable_notification()
pciehp_power_off_slot()
pciehp_get_power_status()
pciehp_get_attention_status()
pciehp_set_attention_status()
pciehp_get_latch_status()
pciehp_get_adapter_status()
pcie_write_cmd()
now always return success, so this patch makes them void and drops the
error-checking code in their callers.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There's not much point in checking the return value from every config space
access because the only likely errors are design-time things like unaligned
accesses or invalid register numbers. The checking clutters the code
significantly, so this patch removes it.
No functional change.
Reference: http://lkml.kernel.org/r/CA+55aFzP4xEbcNmZ+MS0SQ3LrULzSq+dBiT_X9U-bPpR-Ukgrw@mail.gmail.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pciehp_readw() and pciehp_writew() wrappers only look up the pci_dev
and call the PCIe Capability accessors, so we can make things a little
more straightforward by just using the PCIe Capability accessors directly.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
aer_hest_parse() and aer_hest_parse_aff() are almost identical. We use
aer_hest_parse() to check the ACPI_HEST_FIRMWARE_FIRST flag for a specific
device, and we use aer_hest_parse_aff() to check to see if any device sets
the flag.
This drops aer_hest_parse_aff() and enhances aer_hest_parse() so it
collects the union of the PCIe ACPI_HEST_FIRMWARE_FIRST flag settings when
no specific device is supplied.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Betty Dall <betty.dall@hp.com>
aer_set_firmware_first() searches the HEST for an error source descriptor
matching the specified PCI device. It uses the apei_hest_parse() iterator
to call aer_hest_parse() for every descriptor in the HEST.
Previously, aer_hest_parse() incorrectly assumed every descriptor was for a
PCIe error source. This patch adds a check to avoid that error.
[bhelgaas: factor check into helper, use in aer_hest_parse_aff(), changelog]
Signed-off-by: Betty Dall <betty.dall@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Save one indentation level in aer_print_error() for the generic case where
we have info->status of an error, disregard 80 cols rule a bit for the sake
of better readability, fix alignment.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
... and call it instead of duplicating the large printk format
statement.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We need to give up the last reference to edev->dev, so we need to call
put_device().
Signed-off-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/yijing-dev_is_pci:
alpha/PCI: Use dev_is_pci() to identify PCI devices
arm/PCI: Use dev_is_pci() to identify PCI devices
arm/PCI: Use dev_is_pci() to identify PCI devices
parisc/PCI: Use dev_is_pci() to identify PCI devices
sparc/PCI: Use dev_is_pci() to identify PCI devices
ia64/PCI: Use dev_is_pci() to identify PCI devices
x86/PCI: Use dev_is_pci() to identify PCI devices
PCI: Use dev_is_pci() to identify PCI devices
* pci/misc:
PCI: Stop clearing bridge Secondary Status when setting up I/O aperture
PCI: Prevent bus conflicts while checking for bridge apertures
PCI: Drop "irq" param from *_restore_msi_irqs()
PCI/portdrv: Remove superfluous name cast
PCI: Clear NumVFs when disabling SR-IOV in sriov_init()
