The V4L2 sub-device API does not support the crop default target. A number
of drivers apparently still did support this, likely as it was needed by
the SoC camera framework. Drop support for the default crop rectaingle in
sub-device drivers, and use the bounds rectangle in SoC camera instead.
Reported-by: Helmut Grohne <h.grohne@intenta.de>
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If ov772x_power_on() is unable to get GPIO rstb,
the clock is left undisabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Set the V4L2_SUBDEV_FL_HAS_DEVNODE flag for the subdevice so that the
subdevice device node is created.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver is going to offer a V4L2 sub-device interface, so
changing the output data format and the frame interval on this sub-device
can be made anytime. However, these requests are preferred to fail while
the video stream on the device is active.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The set_fmt() in subdev pad ops, the s_ctrl() for subdev control handler,
and the s_frame_interval() in subdev video ops could be called when the
device is under power saving mode. These callbacks for ov772x driver
cause updating H/W registers that will fail under power saving mode.
This avoids it by not apply any changes to H/W if the device is not powered
up. Instead the changes will be restored right after power-up.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver provides three V4L2 controls and the current value of
each control is saved as a variable in the private data structure.
We don't need to keep track of the current value by ourself, if we use
v4l2_ctrl returned from v4l2_ctrl_new_std() instead.
This is a preparatory change to avoid accessing registers under power
saving mode. This simplifies s_ctrl() by making it just return without
saving the current control value in private area when it is called under
power saving mode.
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This splits the s_frame_interval() in subdev video ops into selecting the
frame interval and setting up the registers.
This is a preparatory change to avoid accessing registers under power
saving mode.
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Depending on the v4l2 driver, calling s_power() could be nested. So the
actual transitions between power saving mode and normal operation mode
should only happen at the first power on and the last power off.
This adds an s_power() nesting counter and updates the power state if the
counter is modified from 0 to != 0 or from != 0 to 0.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver currently only supports legacy platform data probe.
This change enables device tree probing.
Note that the platform data probe can select auto or manual edge control
mode, but the device tree probling can only select auto edge control mode
for now.
[Sakari Ailus: Remove direct OF dependencies from device ID table]
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently the ov772x driver obtains a clock with a specific consumer ID.
As there's a single clock for this driver, we could omit clock-names
property in device tree by passing NULL as a consumer ID to clk_get().
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver uses "rstb-gpios" and "pwdn-gpios" for reset and
powerdown pins. However, using generic names for these gpios is
preferred. ("reset-gpios" and "powerdown-gpios" respectively)
There is only one mainline user for these gpios, so rename to generic
names.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Create a source pad and set the media controller type to the sensor.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver only works when the i2c controller have
I2C_FUNC_PROTOCOL_MANGLING. However, many i2c controller drivers don't
support it.
The reason that the ov772x requires I2C_FUNC_PROTOCOL_MANGLING is that
it doesn't support repeated starts.
This changes the reading ov772x register method so that it doesn't
require I2C_FUNC_PROTOCOL_MANGLING by calling two separated i2c messages.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The banding filter ON/OFF is controlled via bit 5 of COM8 register. It
is attempted to be enabled in ov772x_set_params() by the following line.
ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, 1);
But this unexpectedly results disabling the banding filter, because the
mask and set bits are exclusive.
On the other hand, ov772x_s_ctrl() correctly sets the bit by:
ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, BNDF_ON_OFF);
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As the media subdevice is registered with 'v4l2_async_register_subdev()'
unregister it at module removal time with
'v4l2_async_unregister_subdev()'
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
msleep() can sleep up to 20ms.
As suggested by Documentation/timers/timers_howto.txt replace it with
usleep_range() with up to 5ms delay.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add an empty line before return at the end of functions.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A lot of comments that would fit a single line were spread on two or
more lines. Also fix capitalization and punctuation where appropriate.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Align all function parameters to first open brace when declaring
functions.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we're adding this as a new driver, make checkpatch happier by
solving some whitespace issues, using --fix-inplace.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support to ov772x driver for frame intervals handling and enumeration.
Tested with 10MHz and 24MHz input clock at VGA and QVGA resolutions for
10, 15 and 30 frame per second rates.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove soc_camera framework dependencies from ov772x sensor driver.
- Handle clock and gpios
- Register async subdevice
- Remove soc_camera specific g/s_mbus_config operations
- Change image format colorspace from JPEG to SRGB as the two use the
same colorspace information but JPEG makes assumptions on color
components quantization that do not apply to the sensor
- Remove sizes crop from get_selection as driver can't scale
- Add kernel doc to driver interface header file
- Adjust build system
This commit does not remove the original soc_camera based driver as long
as other platforms depends on soc_camera-based CEU driver.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Copy the soc_camera based driver in v4l2 sensor driver directory.
This commit just copies the original file without modifying it.
No modification to KConfig and Makefile as soc_camera framework
dependencies need to be removed first in next commit.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
