As reported by Ben Greer and Froncois Romieu. The code path in
the netif_carrier code leads it to try and disable
a late workqueue to reenable it immediately
netif_carrier_on
-> linkwatch_fire_event
-> linkwatch_schedule_work
-> cancel_delayed_work
-> del_timer_sync
If __cancel_delayed_work is used instead then there is no
problem of waiting for running linkwatch_event.
There is a race between linkwatch_event running re-scheduling
but it is harmless to schedule an extra scan of the linkwatch queue.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor cleanups that won't impact code:
1. Remove inline from non-critical functions; compiler will most
likely inline them anyway.
2. Make function args const where possible.
3. Whitespace cleanup
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When STP changes state of interface need to send a new link
message to reflect that change.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a new device is added to a bridge, the ethernet address of the
bridge network device may change. When the address changes, the
appropriate callback is called, but with the wrong device argument.
The address of the bridge device (ie br0) changes not the address
of the device being passed to add_if (ie eth0).
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the message_age is already greater than the max_age, then the
BPDU is bogus. Linux won't generate BPDU, but conformance tester
or buggy implementation might.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bridge topology with three systems:
+------+ +------+
| A(2) |--| B(1) |
+------+ +------+
\ /
+------+
| C(3) |
+------+
What is supposed to happen:
* bridge with the lowest ID is elected root (for example: B)
* C detects that A->C is higher cost path and puts in blocking state
What happens. Bridge with lowest id (B) is elected correctly as
root and things start out fine initially. But then config BPDU
doesn't get transmitted from A -> C. Because of that
the link from A-C is transistioned to the forwarding state.
The root cause of this is that the configuration messages
is generated with bogus message age, and dropped before
sending.
In the standardmessage_age is supposed to be:
the time since the generation of the Configuration BPDU by
the Root that instigated the generation of this Configuration BPDU.
Reimplement this by recording the timestamp (age + jiffies) when
recording config information. The old code incorrectly used the time
elapsed on the ageing timer which was incorrect.
See also:
https://bugzilla.vyatta.com/show_bug.cgi?id=7164
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
icmp_route_lookup() uses the wrong flow parameters if the reverse
session route lookup isn't used.
So do not commit to the re-decoded flow until we actually make a
final decision to use a real route saved in 'rt2'.
Reported-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the ip fragment offset field counts 8-byte chunks, ip
fragments other than the last must contain a multiple of 8 bytes of
payload. ip_ufo_append_data wasn't respecting this constraint and,
depending on the MTU and ip option sizes, could create malformed
non-final fragments.
Google-Bug-Id: 5009328
Signed-off-by: Bill Sommerfeld <wsommerfeld@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 fragment identification generation is way beyond what we use for
IPv4 : It uses a single generator. Its not scalable and allows DOS
attacks.
Now inetpeer is IPv6 aware, we can use it to provide a more secure and
scalable frag ident generator (per destination, instead of system wide)
This patch :
1) defines a new secure_ipv6_id() helper
2) extends inet_getid() to provide 32bit results
3) extends ipv6_select_ident() with a new dest parameter
Reported-by: Fernando Gont <fernando@gont.com.ar>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently cow metrics a bit too soon in IPv6 case : All routes are
tied to a single inetpeer entry.
Change ip6_rt_copy() to get destination address as second argument, so
that we fill rt6i_dst before the dst_copy_metrics() call.
icmp6_dst_alloc() must set rt6i_dst before calling dst_metric_set(), or
else the cow is done while rt6i_dst is still NULL.
If orig route points to readonly metrics, we can share the pointer
instead of performing the memory allocation and copy.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers (ab)use the ethtool_ops::get_regs operation to expose
only a hardware revision ID. Commit
a77f5db361 ('ethtool: Allocate register
dump buffer with vmalloc()') had the side-effect of breaking these, as
vmalloc() returns a null pointer for size=0 whereas kmalloc() did not.
For backward-compatibility, allow zero-length dumps again.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org [2.6.37+]
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two problems:
1) "n" was allocated with alloc_skb() so we should free it with
kfree_skb() instead of regular kfree().
2) We return the freed pointer instead of NULL.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since vlan_group_get_device and vlan_group is not going to be accessible
from device drivers, introduce function which substitutes it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If overlapping networks with different interfaces was added to
the set, the type did not handle it properly. Example
ipset create test hash:net,iface
ipset add test 192.168.0.0/16,eth0
ipset add test 192.168.0.0/24,eth1
Now, if a packet was sent from 192.168.0.0/24,eth0, the type returned
a match.
In the patch the algorithm is fixed in order to correctly handle
overlapping networks.
Limitation: the same network cannot be stored with more than 64 different
interfaces in a single set.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
commit 58389c69150e6032504dfcd3edca6b1975c8b5bc
Author: Johannes Berg <johannes.berg@intel.com>
Date: Mon Jul 18 18:08:35 2011 +0200
cfg80211: allow userspace to control supported rates in scan
made single-band cards crash since it would always
access all wiphy->bands[]. Fix this and reject any
attempts in the new helper ieee80211_get_ratemask()
to do the same, rejecting rates configuration for
unsupported bands.
Reported-by: Pavel Roskin <proski@gnu.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_stop_rx_ba_session() was calling sta_info_get()
without rcu locking, and the return value was not
checked.
This resulted in the following panic:
[<bf05726c>] (ieee80211_stop_rx_ba_session+0x0/0x60 [mac80211])
[<bf0abd94>] (wl1271_event_handle+0x0/0xdc8 [wl12xx])
[<bf0a7308>] (wl1271_irq+0x0/0x4a0 [wl12xx])
[<c00c40a8>] (irq_thread+0x0/0x254)
[<c00a7398>] (kthread+0x0/0x8c)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_netdev_notifier_call() is configuring psm in case
of NL80211_IFTYPE_STATION interface type (on NETDEV_UP).
do the same for NL80211_IFTYPE_P2P_CLIENT interface type.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In P2P client mode, the GO (AP) to connect to might
have periods of time where it is not available due
to powersave. To allow the driver to sync with it
and send frames to the GO only when it is available
add a new callback tx_sync (and the corresponding
finish_tx_sync). These callbacks can sleep unlike
the actual TX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Scanning currently uses the TX rate mask to
restrict the rate set, which is bogus. Make
it use the new set of rates from userspace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some P2P scans are not allowed to advertise
11b rates, but that is a rather special case
so instead of having that, allow userspace
to request the rate sets (per band) that are
advertised in scan probe request frames.
Since it's needed in two places now, factor
out some common code parsing a rate array.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
open(2) must always include one of O_RDONLY, O_WRONLY, or O_RDWR. No need
for any O_APPEND special case.
Passing O_WRONLY|O_RDWR is undefined according to the man page, but the
Linux VFS interprets this as O_RDWR, so we'll do the same.
This fixes open(2) with flags O_RDWR|O_APPEND, which was incorrectly being
translated to readonly.
Reported-by: Fyodor Ustinov <ufm@ufm.su>
Signed-off-by: Sage Weil <sage@newdream.net>
Introduces a new nfnetlink type that applies a given
verdict to all queued packets with an id <= the id in the verdict
message.
If a mark is provided it is applied to all matched packets.
This reduces the number of verdicts that have to be sent.
Applications that make use of this feature need to maintain
a timeout to send a batchverdict periodically to avoid starvation.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Packet identifier is currently setup in nfqnl_build_packet_message(),
using one atomic_inc_return().
Problem is that since several cpus might concurrently call
nfqnl_enqueue_packet() for the same queue, we can deliver packets to
consumer in non monotonic way (packet N+1 being delivered after packet
N)
This patch moves the packet id setup from nfqnl_build_packet_message()
to nfqnl_enqueue_packet() to guarantee correct delivery order.
This also removes one atomic operation.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Florian Westphal <fw@strlen.de>
CC: Pablo Neira Ayuso <pablo@netfilter.org>
CC: Eric Leblond <eric@regit.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Add tx_conf array to save the current tx queues
configuration, and reconfig it on resume (ieee80211_reconfig).
On resume, the driver is being reconfigured. Without
reconfiguring the tx queues as well, the driver might
configure the device to use wrong ac params (e.g. ps-poll
instead of uapsd).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Compiler is not smart enough to avoid double BSWAP instructions in
ntohl(inet_make_mask(plen)).
Lets cache this value in struct leaf_info, (fill a hole on 64bit arches)
With route cache disabled, this saves ~2% of cpu in udpflood bench on
x86_64 machine.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nenetlink_queue operations on SMP are not efficent if several queues are
used, because of nfnl_mutex contention when applications give packet
verdict.
Use new call_rcu field in struct nfnl_callback to advertize a callback
that is called under rcu_read_lock instead of nfnl_mutex.
On my 2x4x2 machine, I was able to reach 2.000.000 pps going through
user land returning NF_ACCEPT verdicts without losses, instead of less
than 500.000 pps before patch.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Florian Westphal <fw@strlen.de>
CC: Eric Leblond <eric@regit.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Goal of this patch is to permit nfnetlink providers not mandate
nfnl_mutex being held while nfnetlink_rcv_msg() calls them.
If struct nfnl_callback contains a non NULL call_rcu(), then
nfnetlink_rcv_msg() will use it instead of call() field, holding
rcu_read_lock instead of nfnl_mutex
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Florian Westphal <fw@strlen.de>
CC: Eric Leblond <eric@regit.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
In the future dst entries will be neigh-less. In that environment we
need to have an easy transition point for current users of
dst->neighbour outside of the packet output fast path.
Signed-off-by: David S. Miller <davem@davemloft.net>
It just makes it harder to see 1) what the code is doing
and 2) grep for all users of dst{->,.}neighbour
Signed-off-by: David S. Miller <davem@davemloft.net>
This will get us closer to being able to do "neigh stuff"
completely independent of the underlying dst_entry for
protocols (ipv4/ipv6) that wish to do so.
We will also be able to make dst entries neigh-less.
Signed-off-by: David S. Miller <davem@davemloft.net>
there is only one user of vlan_find_dev outside of the actual vlan code:
qlcnic uses it to iterate over some VLANs it knows.
let's just make vlan_find_dev private to the VLAN code and have the
iteration in qlcnic be a bit more direct. (a few rcu dereferences less
too)
Signed-off-by: David Lamparter <equinox@diac24.net>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Amit Kumar Salecha <amit.salecha@qlogic.com>
Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Cc: linux-driver@qlogic.com
Signed-off-by: David S. Miller <davem@davemloft.net>
It's just taking on one of two possible values, either
neigh_ops->output or dev_queue_xmit(). And this is purely depending
upon whether nud_state has NUD_CONNECTED set or not.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that hh_cache entries are embedded inside of neighbour
entries, their lifetimes and accesses are now synchronous
to that of the encompassing neighbour object.
Therefore we don't need to hook up the blackhole op to
hh_output on destroy.
Signed-off-by: David S. Miller <davem@davemloft.net>
