The bounce buffer is gone from the MMC core, and now we found out
that there are some (crippled) i.MX boards out there that have broken
ADMA (cannot do scatter-gather), and also broken PIO so they must
use SDMA. Closer examination shows a less significant slowdown
also on SDMA-only capable Laptop hosts.
SDMA sets down the number of segments to one, so that each segment
gets turned into a singular request that ping-pongs to the block
layer before the next request/segment is issued.
Apparently it happens a lot that the block layer send requests
that include a lot of physically discontiguous segments. My guess
is that this phenomenon is coming from the file system.
These devices that cannot handle scatterlists in hardware can see
major benefits from a DMA-contiguous bounce buffer.
This patch accumulates those fragmented scatterlists in a physically
contiguous bounce buffer so that we can issue bigger DMA data chunks
to/from the card.
When tested with a PCI-integrated host (1217:8221) that
only supports SDMA:
0b:00.0 SD Host controller: O2 Micro, Inc. OZ600FJ0/OZ900FJ0/OZ600FJS
SD/MMC Card Reader Controller (rev 05)
This patch gave ~1Mbyte/s improved throughput on large reads and
writes when testing using iozone than without the patch.
dmesg:
sdhci-pci 0000:0b:00.0: SDHCI controller found [1217:8221] (rev 5)
mmc0 bounce up to 128 segments into one, max segment size 65536 bytes
mmc0: SDHCI controller on PCI [0000:0b:00.0] using DMA
On the i.MX SDHCI controllers on the crippled i.MX 25 and i.MX 35
the patch restores the performance to what it was before we removed
the bounce buffers.
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Benoît Thébaudeau <benoit@wsystem.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Benjamin Beckmeyer <beckmeyer.b@rittal.de>
Cc: stable@vger.kernel.org # v4.14+
Fixes: de3ee99b09 ("mmc: Delete bounce buffer handling")
Tested-by: Benjamin Beckmeyer <beckmeyer.b@rittal.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that sdhci_enable_irq_wakeups() is a local function, change it to
return whether the IRQ wakeup was successfully enabled. This is in
preparation for adding more conditions for whether IRQ wakeup is enabled.
Note it is assumed, for SDHCI devices, that suspend is more important than
wakeup, so we continue to suspend regardless.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that it is not being used by any drivers, stop exporting it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
TI's implementation of sdhci controller used in DRA7 SoC's has
CRC in responses with length 136 bits. Add quirk to indicate
the controller has CRC in MMC_RSP_136. If this quirk is
set sdhci library shouldn't shift the response present in
SDHCI_RESPONSE register.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds sdma_boundary member to struct sdhci_host to give more
flexibility to drivers to control the sdma boundary buffer value and
also to fix issue on some sdhci controllers which are broken when
HOST SDMA Buffer Boundary is programmed in Block Size Register (0x04)
when using ADMA. Qualcomm sdhci controller is one of such type, writing
to this bits is un-supported.
Default value of sdma_boundary is set to SDHCI_DEFAULT_BOUNDARY_ARG.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The delay between tuning commands for SD cards is not part of the
specification. A driver that needs it probably needs it for eMMC
too, whereas most drivers would probably like to set it to 0. Make
it a host member (host->tuning_delay) that defaults to the existing
behaviour. Drivers can set it to zero to eliminate the delay, or
set it to a positive value to always have a delay.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Export sdhci_start_signal_voltage_switch() from sdhci.c.
Thus vendor sdhci driver can implement its own signal voltage
switch routine.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Export sdhci_set_ios() in sdhci.c.
Thus vendor sdhci driver can implement its own set_ios() routine.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the get_timeout_clock callback doesn't clearly
have a statement that it needs the variant drivers to return
the timeout clock rate in kHz if the SDHCI_TIMEOUT_CLK_UNIT
isn't present, otherwise the variant drivers should return it
in MHz. It's also very likely that further variant drivers which
are going to use this callback will be confused by this situation.
Given the fact that moderm sdhci variant hosts are very prone to get
the timeout clock from common clock framework (actually the only three
users did that), it's more natural to return the value in Hz and we
make an explicit comment there. Then we put the unit conversion inside
the sdhci core. Thus will improve the code and prevent further misuses.
Reported-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add an interrupt hook and helper functions for enabling, disabling and
delivering interrupts to a CQE.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Get rid of unnecessary 'extern' in header file.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Export sdhci_dumpregs so that it can be called by drivers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Drivers can use the host operation directly, so remove this now unused
callback.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
An mmc host driver shouldn't rely on interrupt.h being included by another
public mmc header. Instead make that dependency explicit by including
interrupt.h in those host drivers that depends on it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Don't rely on host.h to include the leds.h header, but instead include it
explicitly because the driver depends on it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Some SDHCI-compat controllers support not only SD, but also eMMC,
but they use different commands for tuning: CMD19 for SD, CMD21 for
eMMC.
Due to the difference of the underlying mechanism, some controllers
(at least, the Cadence IP is the case) provide their own registers
for the eMMC tuning.
This commit will be useful when we want to override .execute_tuning
callback (for eMMC HS200 tuning), but still let it fall back to
sdhci_execute_tuning() for SD timing.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out sdhci_enable_clk from sdhci_set_clock
and make it EXPORT_SYMBOL so that it can be called.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The type of host->private is (unsigned long *). No cast is needed
to return an opaque pointer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit 87a18a6a56 ("mmc: mmc: Use ->card_busy() to detect busy
cards in __mmc_switch()") the ESDHC driver is broken:
mmc0: Card stuck in programming state! __mmc_switch
mmc0: error -110 whilst initialising MMC card
Since this commit __mmc_switch() uses ->card_busy(), which is
sdhci_card_busy() for the esdhc driver. sdhci_card_busy() uses the
PRESENT_STATE register, specifically the DAT0 signal level bit. But the
ESDHC uses a non-conformant PRESENT_STATE register, thus a read fixup is
required to make the driver work again.
Signed-off-by: Michael Walle <michael@walle.cc>
Fixes: 87a18a6a56 ("mmc: mmc: Use ->card_busy() to detect busy cards in __mmc_switch()")
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Unlike other cases, sdhci_set_power() does not reflect the default
implementation of the ->set_power() callback. Rename it and create
sdhci_set_power() that is the default implementation.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci controller on xilinx zynq devices will not function unless
the CD bit is provided. http://www.xilinx.com/support/answers/61064.html
In cases where it is impossible to provide the CD bit in hardware,
setting the controller to test mode and then setting inserted to true
will get the controller to function without the CD bit.
When the device has the property xlnx,fails-without-test-cd the driver
changes the controller to test mode and sets test inserted to true to
make the controller function.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 1ef5e49e46 ("mmc: sdhci-of-esdhc: add/remove some quirks
according to vendor version") moved sdhci-of-esdhc away from using the
->platform_init() callback.
As it was the only user of it and that it seems reasonable to believe that
it won't be needed again, let's just remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
If HW supports SDHCI_TUNING_MODE_3 which is auto retuning, we won't
retune during runtime suspend and resume, instead we use Re-tuning
Request signaled via SDHCI_INT_RETUNE interrupt to do retuning and
hw auto retuning during data transfer to guarantee the signal sample
window correction.
This can avoid a mass of repeatedly retuning during small file system
data access and improve the performance.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds the missing define for the suspend/resume
capability (according to SD Host Controller spec).
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to support commands during data transfer, there will have to be up
to two active requests (mrqs) at a time, instead of just one. That means
recording which request is finished. Doing that obsoletes host->mrq which
is therefore removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to support commands during data transfer, there will have to be up
to two active requests (mrqs) at a time, instead of just one. Provide two
timers instead of just one. One of the timers is for requests that do not
use the data lines, and the other one is for requests that do.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI recovers from errors by resetting the cmd and data circuits. Until
that is done, there very well might be more interrupts, so ignore them in
that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that there is host->data_cmd to record the command for which a data
interrupt is expected, it is possible to determine whether a command with
busy signaling has completed without an extra flag. So host->busy_handle
is not needed. Remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to support commands during data transfer, there must be a
distinction between the command that is using the command line (and
for which a command interrupt is expected) and the command that is
using the data lines (for which a data interrupt is expected).
There is host->cmd for the command line, but there is only host->data
for the data lines, which is a different structure, does not represent
the command in use, and is anyway NULL in the case of commands that use
the data lines for busy signalling instead of data transfer.
Introduce host->data_cmd to record what command is using the data lines,
and use that instead of host->cmd when referring to the data command.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add sdhci_read_caps() and __sdhci_read_caps() to make it easier for drivers
to fix the version and capabilities registers.
Pedantically, the SDHCI specification states that the capabilities
registers are valid when the host controller resets the Software Reset For
All bit. That requirement has always been satisfied by performing a reset
at the start of initialization, and consequently that is now part of the
new functions.
Although the SDHCI_QUIRK_MISSING_CAPS quirk has not yet been removed,
drivers that want to provide their own caps can now use these functions
instead of that quirk.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for adding a function to read the capability registers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signal voltage support is not a quirk, it is a capability. According to the
SDHCI specification, support for 1.8V signaling is determined by the
presence of one of the capability bits SDHCI_SUPPORT_SDR50,
SDHCI_SUPPORT_SDR104, or SDHCI_SUPPORT_DDR50. This is complicated by also
supporting eMMC which has 1.8V modes and 1.2V modes. It would be possible
to use the transfer mode to determine signal voltage support, except for
eMMC DDR52 mode which uses the same capability (MMC_CAP_1_8V_DDR) for 1.8V
signaling and 3V signaling.
In addition, the mmc core will fail over from one signaling voltage to the
next (refer mmc_power_up()) which means SDHCI really needs to validate
which voltages are actually supported.
Introduce SDHCI flags for signal voltage support and set them based on the
supported transfer modes. In general, drivers should prefer to set the
supported transfer modes correctly rather than change the signal voltage
capability, except in the case where 3V DDR52 is supported but 1.8V is
not.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Split sdhci-add_host() in order to further our objective to make
sdhci into a library.
The split divides code that sets up mmc and sdhci parameters, from
code that actually activates things - such as tasklet initialization,
requesting the irq, and adding (and starting) the host.
This gives drivers an opportunity to change various settings before
committing to start the host.
Drivers can continue to call sdhci_add_host() but drivers that want
to take advantage of the split instead call sdhci_setup_host() followed
by __sdhci_add_host().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI_SDR104_NEEDS_TUNING was originally named SDHCI_HS200_NEEDS_TUNING
and was added in commit 069c9f1428 ("mmc: host: Adds support for eMMC
4.5 HS200 mode").
That commit conflated SDHCI_SDR50_NEEDS_TUNING and SDHCI_HS200_NEEDS_TUNING
due to what appears to be misplaced parentheses.
Commit 156e14b126 ("mmc: sdhci: fix caps2 for HS200") made HS200
configuration equivalent to SDR104 configuration, renaming
SDHCI_HS200_NEEDS_TUNING to SDHCI_SDR104_NEEDS_TUNING despite tuning for
HS200 now being non-optional.
The mix-up with SDHCI_SDR50_NEEDS_TUNING remained and became more obvious
after commit 4b6f37d3a3 ("mmc: sdhci: clean up sdhci_execute_tuning()
decision") where the author noted the patch was "reflecting what the
original code was doing, it shows that it may not be what the author
actually intended."
The way the code is currently written, SDHCI_SDR104_NEEDS_TUNING
causes tuning to be done always for SDR50 mode if SDR104 mode is
also supported by the host controller. That makes no sense because
we already have capabilities bit SDHCI_USE_SDR50_TUNING and
corresponding flag SDHCI_SDR50_NEEDS_TUNING for that purpose.
Given the dubious origins of SDHCI_SDR104_NEEDS_TUNING, it seems
reasonable to remove it. The benefit being SDR50 mode will now not
un-nessessarily do tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST quirk is not used anymore so
remove it.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to remove the SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST and to
reduce code duplication, put the code relative to the SD clock
configuration in a function which can be used by hosts for the
implementation of the ->set_clock() callback.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit d31911b937 ("mmc: sdhci: fix dma memory leak in sdhci_pre_req()")
added a complicated method to manage the DMA map state for the data
transfer, but this complexity is not required.
There are three states:
* Unmapped
* Mapped by sdhci_pre_req()
* Mapped by sdhci_prepare_data()
sdhci_prepare_data() needs to know when the data buffers have been
successfully mapped by sdhci_pre_req(), and if so, there is no need to
map them a second time.
When we come to tear down the mapping, we want to know whether
sdhci_post_req() will be called (which is determined by sdhci_pre_req()
having been previously called) so that we can postpone the unmap
operation.
Hence, it makes sense to simply record when the successful DMA map
happened (via COOKIE_PRE_MAPPED vs COOKIE_MAPPED) rather than having
the complex mechanics involving COOKIE_MAPPED vs COOKIE_GIVEN.
If a mapping is created by sdhci_prepare_data(), we must tear it down
ourselves, without waiting for sdhci_post_req() (hence, the new
COOKIE_MAPPED case). If the mapping is created by sdhci_pre_req()
then sdhci_post_req() is responsible for tearing the mapping down.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the past, fixes for specific hardware devices were implemented
in sdhci using quirks. That approach is no longer accepted because
the growing number of quirks was starting to make the code difficult
to understand and maintain.
One alternative to quirks, is to allow drivers to override the default
mmc host operations. This patch makes it easy to do that, and it is
needed for a subsequent bug fix, for which separate patches are
provided.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The version 3.00 SDHCI spec. was a bit unclear about the
required data alignment for 64-bit DMA, whereas the version
4.10 spec. uses different language and indicates that only
4-byte alignment is required rather than the 8-byte alignment
currently implemented. That make no difference to SD and EMMC
which invariably transfer data in sector-aligned blocks.
However with SDIO, it results in using more DMA descriptors
than necessary. Theoretically that slows DMA slightly although
DMA is not the limiting factor for throughput, so there is no
discernable impact on performance. Nevertheless, the driver
should follw the spec unless there is good reason not to, so
this patch corrects the alignment criterion.
There is a more complicated criterion for the DMA descriptor
table itself. However the table is allocated by dma_alloc_coherent()
which allocates pages (i.e. aligned to a page boundary).
For simplicity just check it is 8-byte aligned, but add a comment
that some Intel controllers actually require 8-byte alignment
even when using 32-bit DMA.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Atmel sdhci device needs a new quirk. sdhci_set_clock set the Clock
Control Register to 0 before computing the new value and writing it.
It disables the internal clock which causes a reset mecanism. If we
write the new value before this reset mecanism is done, it will prevent
the stabilisation of the internal clock, so a delay is needed. This
delay is about 2-3 cycles of the base clock. To be safe, a 1 ms delay is
used.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently one mrq->data maybe execute dma_map_sg() twice
when mmc subsystem prepare over one new request, and the
following log show up:
sdhci[sdhci_pre_dma_transfer] invalid cookie: 24, next-cookie 25
In this condition, mrq->date map a dma-memory(1) in sdhci_pre_req
for the first time, and map another dma-memory(2) in sdhci_prepare_data
for the second time. But driver only unmap the dma-memory(2), and
dma-memory(1) never unmapped, which cause the dma memory leak issue.
This patch use another method to map the dma memory for the mrq->data
which can fix this dma memory leak issue.
Fixes: 348487cb28 ("mmc: sdhci: use pipeline mmc requests to improve performance")
Reported-and-tested-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
adds quirk for controllers whose clock divider zero is broken,
sdhci_set_clock function will incorporate this modification.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a callbak to let host drivers select drive
strength.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of mmc core support for re-tuning instead
of doing it all in the sdhci driver.
This patch also changes to flag the need for re-tuning
always after runtime suspend when tuning has been used
at initialization. Previously it was only done if
the re-tuning timer was in use.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since there no users of the struct sdhci_host, but the shdci host
drivers themselves, let's move the definition of it to the local sdhci
header.
The exported sdhci header then becomes empty, so let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a callback function to do
controller-specific actions when switching voltages.
It is a preparation and will be used by Fujitsu
SDHCI controller f_sdh30 driver.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
