Be more accurate about number of transmit list elements required.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs,serial_cs:
add cis of Linksys lan&modem mulitifunction pcmcia card
and some modem card(MT5634ZLX, RS-COM-2P).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes commit e36b9d16c6. The approach
there is to call dev_close()/dev_open() whenever the device type is changed in
order to remap the device IP multicast addresses to HW multicast addresses.
This approach suffers from 2 drawbacks:
*. It assumes tha the device is UP when calling dev_close(), or otherwise
dev_close() has no affect. It is worth to mention that initscripts (Redhat)
and sysconfig (Suse) doesn't act the same in this matter.
*. dev_close() has other side affects, like deleting entries from the routing
table, which might be unnecessary.
The fix here is to directly remap the IP multicast addresses to HW multicast
addresses for a bonding device that changes its type, and nothing else.
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using nanosleep() in an userspace application we get a ratelimit warning
NOHZ: local_softirq_pending 08
for 10 times.
The echo of CAN frames is done from process context and softirq context only.
Therefore the usage of netif_rx() was wrong (for years).
This patch replaces netif_rx() with netif_rx_ni() which has to be used from
process/softirq context. It also adds a missing comment that can_send() must
no be used from hardirq context.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Urs Thuermann <urs@isnogud.escape.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (257 commits)
[ARM] Update mach-types
ARM: 5636/1: Move vendor enum to AMBA include
ARM: Fix pfn_valid() for sparse memory
[ARM] orion5x: Add LaCie NAS 2Big Network support
[ARM] pxa/sharpsl_pm: zaurus c3000 aka spitz: fix resume
ARM: 5686/1: at91: Correct AC97 reset line in at91sam9263ek board
ARM: 5640/1: This patch modifies the support of AC97 on the at91sam9263 ek board
ARM: 5689/1: Update default config of HP Jornada 700-series machines
ARM: 5691/1: fix cache aliasing issues between kmap() and kmap_atomic() with highmem
ARM: 5688/1: ks8695_serial: disable_irq() lockup
ARM: 5687/1: fix an oops with highmem
ARM: 5684/1: Add nuc960 platform to w90x900
ARM: 5683/1: Add nuc950 platform to w90x900
ARM: 5682/1: Add cpu.c and dev.c and modify some files of w90p910 platform
ARM: 5626/1: add suspend/resume functions to amba-pl011 serial driver
ARM: 5625/1: fix hard coded 4K resource size in amba bus detection
MMC: MMCI: convert realview MMC to use gpiolib
ARM: 5685/1: Make MMCI driver compile without gpiolib
ARM: implement highpte
ARM: Show FIQ in /proc/interrupts on CONFIG_FIQ
...
Fix up trivial conflict in arch/arm/kernel/signal.c.
It was due to the TIF_NOTIFY_RESUME addition in commit d0420c83f ("KEYS:
Extend TIF_NOTIFY_RESUME to (almost) all architectures") and follow-ups.
In the case of fiber and serdes adapters we were seeing issues with ethtool
-t causing kernel panics due to null function pointers. To prevent this we
need to exit out of the phy reset code in the event that we do not have a
valid phy.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our SGMII phy code was incomplete in that it was not actually placing the
phy in SGMII mode and as a result the PHY was not able to establish a link
when connected to a non serdes link partner. This patch updates the code
to combine the SGMII/serdes PCS init and to add the necessary reset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the media type detection for CX4 adapters lumps them into a
type of fiber. This causes some strange fallout when firmware verification
is done on the NIC, and certain fiber NIC rules get enforced incorrectly.
This patch introduces a new media type for CX4, and puts both 82598 and
82599 CX4 adapters into this bucket.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for CX4 adapters based on 82599.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet split feature was recently moved out of the adapter-wide flags
feature field and into a per-Rx ring feature field. In the process, packet
split isn't properly disabled in the Rx ring if the adapter has it globally
disabled, followed by a device reset.
This won't impact the driver today, since it's always in packet split mode.
However, this will prevent any pitfalls if someone disables packet split on
the adapter in the future and doesn't disable it in each ring.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all Blackfin boards are using the board resources, we don't need
to keep the arch/board specific crap in the driver header.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a bug in 4965 powersave that appears to
be related to the way it keeps track of its data
during sleep, but we haven't found it yet. Due to
that, using powersave may spontaneously cause the
device to SYSASSERT when transitioning from sleep
to wake. Therefore, disable powersave for 4965,
until (if ever, unfortunately) we can identify
and fix the problem.
Cf. http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1982
which was closed, but now has re-appeared with
IDLE mode, which probably means we never really
fixed it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can not assume antenna "A" is the first valid anttena for
all the NIC. Need to make sure choice the correct antenna based on
h/w configuration for transmit to avoid sending frame on invalid
antenna
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX handling maintains a few lists that keep track of the RX buffers.
Buffers move from one list to the other as they are used, replenished, and
again made available for usage. In one such instance, when a buffer is used
it enters the "rx_used" list. When buffers are replenished an skb is
attached to the buffer and it is moved to the "rx_free" list. The problem
here is that the buffer is first removed from the "rx_used" list _before_ the
skb is allocated. Thus, if the skb allocation fails this buffer remains
removed from the "rx_used" list and is thus lost for future usage.
Fix this by first allocating the skb before trying to attach it to a list.
We add an additional check to not do this unnecessarily.
Reported-by: Rick Farrington <rickdic@hotmail.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we cleaned up the driver to properly tell mac80211 about HT rates
("iwlwifi: use iwl_hwrate_get_mac80211_idx where appropriate"), we broke
internal rate indexing in 2.4 GHz band.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Tested-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a resume failure where a signal is pending on resume
so the firmware upload fails.
This removes the interruptible sleep, because we don't really need it.
In the worst case (with broken firmware) the sleep loop will take 1 second.
In the common case (working firmware), it will only take a few milliseconds.
So we don't really need to be interruptible.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When this was added no defaults were set and it seems
this implies n. Default this to y.
Reported-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When processing MIB interrupts, OFDM and CCK error
handling routines for low RSSI values have to be invoked
only when the channel mode is 11G/11B. Since HT channels
will also fall under the bands 2Ghz/5Ghz, check appropriately.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Force wake the mac80211 queues on init.
Under rare circumstances they may be stopped, if a DMA error or
something else causes a device reset while a queue was stopped.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the hostap driver was converted to use net_device_ops, a mistake was
made in hostap_main.c (commit 5ae4efbcd2).
Originally, the tx_queue_len was set to 0 for every other interface than
HOSTAP_INTERFACE_MASTER, but the new fragment of code sets tx_queue_len to
0 only for HOSTAP_INTERFACE_MASTER. The opposite of the previous
behavior makes the driver to drop all packets in AP mode.
Change the way 0 is assigned to tx_queue_len according to the original
logic.
Signed-off-by: Martin Decky <martin@decky.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
o Add QLogic copyright, add linux-driver@qlogic.com to
MAINTAINERS.
o Delete old contact information.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redesign tx timeout handling in line with new firmware
reset design that co-ordinates with other PCI function
drivers.
o For NX3031, first try to reset PCI function's own
context before requesting firmware reset.
o For NX2031, since firmware heartbit is not supported
directly request firmware reset.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Release file firmware when no firmware reset is required.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Access on card memory through memory controller (agent)
rather than moving small pci window around. Clean up the
code for moving windows around.
o Restrict memory accesss to 64 bit, currently only firmware
download uses this.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 8 byte strides for firmware download into card
memory since oncard memory controller needs 8 byte
(64 bit) accesses. This avoids unnecessary rmw cycles.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f6eb9b1fc1, "tg3: Add 5717 asic
rev" changed how the rx return ring size operations are done. It
effectively inverts the sense of the previous test, but it failed to
also invert the resulting sizes. This patch corrects that error.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_INET is disabled, netxen has a build failure:
netxen_nic_main.c:(.text+0x118fd1): undefined reference to `netxen_config_indev_addr'
so make that function just an empty stub when CONFIG_INET=n.
(not "inline" since that conflicts with other declarations of it)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet framing is used for a lot of devices these days. Most
prominent are WiFi and WiMAX based devices. However for userspace
application it is important to classify these devices correctly and
not only see them as Ethernet devices. The daemons like HAL, DeviceKit
or even NetworkManager with udev support tries to do the classification
in userspace with a lot trickery and extra system calls. This is not
good and actually reaches its limitations. Especially since the kernel
does know the type of the Ethernet device it is pretty stupid.
To solve this problem the underlying device type needs to be set and
then the value will be exported as DEVTYPE via uevents and available
within udev.
# cat /sys/class/net/wlan0/uevent
DEVTYPE=wlan
INTERFACE=wlan0
IFINDEX=5
This is similar to subsystems like USB and SCSI that distinguish
between hosts, devices, disks, partitions etc.
The new SET_NETDEV_DEVTYPE() is a convenience helper to set the actual
device type. All device types are free form, but for convenience the
same strings as used with RFKILL are choosen.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The txq_set_wrr() function in drivers/net/mv643xx_eth.c is
unused, not even referenced under #if 0 or something like that,
which results in a compile-time warning:
drivers/net/mv643xx_eth.c:1070: warning: 'txq_set_wrr' defined but not used
Fix: remove it.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPC8360 QE UCC ethernet controllers hang when changing link duplex
under a load (a bit of NFS activity is enough).
PHY: mdio@e0102120:00 - Link is Up - 1000/Full
sh-3.00# ethtool -s eth0 speed 100 duplex half autoneg off
PHY: mdio@e0102120:00 - Link is Down
PHY: mdio@e0102120:00 - Link is Up - 100/Half
NETDEV WATCHDOG: eth0 (ucc_geth): transmit queue 0 timed out
------------[ cut here ]------------
Badness at c01fcbd0 [verbose debug info unavailable]
NIP: c01fcbd0 LR: c01fcbd0 CTR: c0194e44
...
The cure is to disable the controller before changing speed/duplex
and enable it afterwards.
Though, disabling the controller might take quite a while, so we
better not grab any spinlocks in adjust_link(). Instead, we quiesce
the driver's activity, and only then disable the controller.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll need ugeth_disable() and ugeth_enable() calls earlier in the
file, so rearrange some code to avoid forward declarations.
The patch doesn't contain any functional changes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to specs, when auto-negotiation is disabled, Marvell PHYs need
a software reset after changing speed/duplex forcing bits. Otherwise,
the modified bits have no effect.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error handling code following a kzalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
And also do a better job of returning proper NET_{RX,XMIT}_ values.
Based on a patch and suggestions by Mark Smith.
This fixes CVE-2009-2903
Reported-by: Mark Smith <lk-netdev@lk-netdev.nosense.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (48 commits)
RDMA/iwcm: Reject the connection when the cm_id is destroyed
RDMA/cxgb3: Clean up properly on FW mismatch failures
RDMA/cxgb3: Don't ignore insert_handle() failures
MAINTAINERS: InfiniBand/RDMA mailing list transition to vger
IB/mad: Allow tuning of QP0 and QP1 sizes
IB/mad: Fix possible lock-lock-timer deadlock
RDMA/nes: Map MTU to IB_MTU_* and correctly report link state
RDMA/nes: Rework the disconn routine for terminate and flushing
RDMA/nes: Use the flush code to fill in cqe error
RDMA/nes: Make poll_cq return correct number of wqes during flush
RDMA/nes: Use flush mechanism to set status for wqe in error
RDMA/nes: Implement Terminate Packet
RDMA/nes: Add CQ error handling
RDMA/nes: Clean out CQ completions when QP is destroyed
RDMA/nes: Change memory allocation for cqp request to GFP_ATOMIC
RDMA/nes: Allocate work item for disconnect event handling
RDMA/nes: Update refcnt during disconnect
IB/mthca: Don't allow userspace open while recovering from catastrophic error
IB/mthca: Distinguish multiple devices in /proc/interrupts
IB/mthca: Annotate CQ locking
...
and convert PXA-based devices to gpio_pwdown where possible.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The macro res_size in drivers/net/dm9000.c is a copy of resource_size in
linux/ioport.h. Remove the function and use resource_size instead.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory for the private data is allocated using kzalloc in
alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to
set it to 0 again.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the offset of vlan_TCI field in cmd_desc_type0.
Signed-off-by: Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typo in checking dest ip has support before
programming destip addresses.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oops, a stupid mistake in the original patch which adds coex 3-wire
support. Bluetooth priority gpio needs to be gpio 7.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This subsystem id will be used later to turn on the btcoex
support.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The preferred module is p54pci which also supports FullMAC
PCI / Cardbus devices. We schedule removal for 2.6.34. Reason
to remove this is no one really is testing prism54 anymore,
and while it works p54pci provides support for the same hardware.
It should be noted I have been told some FullMAC devices may not
have worked with the SoftMAC driver but to date we have yet to
recieve a single bug report regarding this. If there are users
out there please let us know!
Cc: aquilaver@yahoo.com
Cc: linux-kernel@vger.kernel.org
Cc: Dan Williams <dcbw@redhat.com>
Cc: Kai Engert <kengert@redhat.com>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Cc: Tim de Waal<tim.dewaal@yahoo.com>
Cc: Roy Marples <uberlord@gentoo.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Christian Lamparter <chunkeey@web.de>
Cc: Björn Steinbrink <B.Steinbrink@gmx.de>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes some gcc warnings for switch statements.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a sparse warning in the hardware-TKIP code:
drivers/net/wireless/b43/xmit.c:272:18: warning: incorrect type in assignment (different base types)
drivers/net/wireless/b43/xmit.c:272:18: expected unsigned short [unsigned] [short] <noident>
drivers/net/wireless/b43/xmit.c:272:18: got restricted unsigned short [usertype] <noident>
The code should work correctly with and without this patch applied.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when QoS-disable is requested, we would leave QoS enabled
in firmware, but only queue frames on one queue.
Change that and also tell firmware about disabled QoS, so it
completely ignores all the QoS parameters. Also don't upload the parameters,
if QoS is disabled.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calculated values for the ACK timeout and ACK
consume time are different then the values as
used by the Legacy drivers.
After testing from James Ledwith it appeared that
the calculated values caused a high amount of TX
failures, and the values from the Legacy drivers
were the most optimal to prevent TX failure due to
excessive retries.
The symptoms of this problem:
- Rate control module always falls back to 1Mbs
- Low throughput when bitrate was fixed
Possible side-effects (not confirmed but highly likely)
- Problems with DHCP
- Broken connections due to lack of probe response
This should fix at least:
Kernel bugzilla reports: [13362], [13009], [9273]
Fedora bugzilla reports: [443203]
but possible some additional bugs as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function res_size in drivers/net/niu.c is a copy of resource_size in
linux/ioport.h. Remove the function and use resource_size instead.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCMCIA support works well and is not experimental anymore.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
apply the conformance test limits (CTL) stored in the eeprom upon
the values calculated for the tx power (ar->power_*).
This is based on the implementation in the vendor driver
(hal/hpmain.c, line 3700 ff.) with one difference:
If any ctl mode isn't found in the eeprom, we fall back to the "lower",
legacy modes (5GHT20,11A or 2GHT20,11G,11B). Otus only did 5GHT20->11A.
Currently CTL are applied for the FCC group only.
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ar9170 driver needs the defines for conformance test limit groups
and cannot include regd_common.h
Signed-off-by: Joerg Albert <jal2@gmx.de>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the SHM spinlock.
SHM is protected by wl->mutex.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the PIO RX work. It's not needed anymore, because
we can sleep in the threaded interrupt handler.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the DMA/PIO queue locks. Locking is handled by
wl->mutex now.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the TX spinlock and defers TX to a workqueue to allow
locking wl->mutex instead and to allow sleeping for register accesses.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a threaded IRQ handler to allow locking the mutex and
sleeping while executing an interrupt.
This removes usage of the irq_lock spinlock, but introduces
a new hardirq_lock, which is _only_ used for the PCI/SSB lowlevel
hard-irq handler. Sleeping busses (SDIO) will use mutex instead.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ports some code from the vendor driver, which is
supposed to upload the right calibration values for the
chosen frequency.
In theory, this should give a better range and throughput
for all users with the open, or one-stage firmware.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHANNEL_G has to be set for 2GHZ channels since
IS_CHAN_G() checks for this in channelFlags and not in
chanmode. To make things messier, ath9k_hw_process_ini()
checks for CHANNEL_G in chanmode and not in channelFlags.
The supreme, brain-searing fix is to set the
flag in both cases.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BAR frames have to be sent to mac80211 only if the
current channel is HT. Also, move the macro to
enum ath9k_rx_filter.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k ahb requests an IRQ and indicates 'ath9k' claimed it,
ath9k pci requests an IRQ and indicates 'ath' claims it;
since 'ath' is another module sync both ahb and pci to claim
the irq using 'ath9k'.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've cleaned up ath_init_device() and its children enough
to pass meaninful errors back from probe. When this fails
it means our device could not be initialized and a meaninful
error will have been passed.
Do the same for request_irq() and also synchronize the error
messages while at it.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The -ENOMEM was never being passed on failure.
While at it use dev_err() as ahb does upon failure.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the initialisation of some PHY registers
from the modal_header[] values in the EEPROM
(see otus/hal/hpmain.c, line 333 ff.)
Signed-off-by: Joerg Albert <jal2@gmx.de>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported by Stephen Rothwell:
drivers/net/r8169.c: In function 'rtl8169_start_xmit':
drivers/net/r8169.c:3421: warning: label 'out' defined but not used
Introduced by commit 61357325f3 ("netdev:
convert bulk of drivers to netdev_tx_t").
Signed-off-by: David S. Miller <davem@davemloft.net>
m68k:
drivers/net/hydra.c:178: warning: format '%08lx' expects type 'long unsigned int', but argument 3 has type 'resource_size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HSS usually uses external clocks, so it's not a big deal. Internal clock
is used for direct DTE-DTE connections and when the DCE doesn't provide
it's own clock.
This also depends on the oscillator frequency. Intel seems to have
calculated the clock register settings for 33.33 MHz (66.66 MHz timer
base). Their settings seem quite suboptimal both in terms of average
frequency (60 ppm is unacceptable for G.703 applications, their primary
intended usage(?)) and jitter.
Many (most?) platforms use a 33.333 MHz oscillator, a 10 ppm difference
from Intel's base.
Instead of creating static tables, I've created a procedure to program
the HSS clock register. The register consists of 3 parts (A, B, C).
The average frequency (= bit rate) is:
66.66x MHz / (A + (B + 1) / (C + 1))
The procedure aims at the closest average frequency, possibly at the
cost of increased jitter. Nobody would be able to directly drive an
unbufferred transmitter with a HSS anyway, and the frequency error is
what it really counts.
I've verified the above with an oscilloscope on IXP425. It seems IXP46x
and possibly IXP43x use a bit different clock generation algorithm - it
looks like the avg frequency is:
(on IXP465) 66.66x MHz / (A + B / (C + 1)).
Also they use much greater precomputed A and B - on IXP425 it would
simply result in more jitter, but I don't know how does it work on
IXP46x (perhaps 3 least significant bits aren't used?).
Anyway it looks that they were aiming for exactly +60 ppm or -60 ppm,
while <1 ppm is typically possible (with a synchronized clock, of
course).
The attached patch makes it possible to set almost any bit rate
(my IXP425 533 MHz quits at > 22 Mb/s if a single port is used, and the
minimum is ca. 65 Kb/s).
This is independent of MVIP (multi-E1/T1 on one HSS) mode.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI200SYN has its own PCI subsystem device ID for 3+ years, now it's
time to remove the generic PLX905[02] ID from the driver. Anyone with
old EEPROM data will have to run the upgrade.
Having the generic PLX905[02] (PCI-local bus bridge) ID is harmful
as the driver tries to handle other devices based on these bridges.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code changes to
- In the tx completion processing, there were instances of unmapping a
memory as a page which was originally mapped as single. This patch takes care
of this by using skb_dma_map()/skb_dma_unmap() to map/unmap Tx buffers.
- set gso_max_size to 65535. This was not done till now.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to support flashing of the be2 network adapter using the
request_firmware() & ethtool infrastructure. The trigger to flash the device
will come from ethtool utility. The driver will invoke request_firmware()
to start the flash process. The file containing the flash image is expected
to be available in /lib/firmware/
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a brute force removal of the wierd slave interface done for
DLCI -> SDLA transmit. Before it was using non-standard return values
and freeing skb in caller. This changes it to using normal return
values, and freeing in the callee. Luckly only one driver pair was
doing this. Not tested on real hardware, in fact I wonder if this
driver pair is even being used by any users.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Combine netxen_get_firmware_info(), netxen_check_options()
so that they are updated every time firmware is reset.
o Set dma mask everytime firmware is reset.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For registers accessed in fast path (interrupt / softirq)
avoid expensive I/O address translation. These registers
are directly mapped in PCI bar 0 and do not require
any window checks.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reprogram local IP addresses after firmware is reset
or after resuming from suspend.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement state machine to detect firmware hung state
and recover. Since firmware will be shared by all PCI
functions that have different class drivers (NIC or
FCOE or iSCSI), explicit hardware based serialization
is required for initializing firmware.
o Used global scratchpad register to maintain device
reference count. Every probed pci function adds to
ref count.
o Implement timer (delayed work) for each pci func
that checks firmware heartbit every 5 sec and detaches
itself if firmware is dead. Last detaching function
reloads firmware. Other functions wait for firmware
init, and re-attach themselves.
Heartbit is not supported by NX2031 firmware.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unwind allocations and release file firmware when
when firmware load fails.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by Michael Guntsche <mike@it-loops.com>
--------------------
Commit
38bddf04bc gianfar: gfar_remove needs to call unregister_netdev()
breaks the build of the gianfar driver because "dev" is undefined in
this function. To quickly test rc9 I changed this to priv->ndev but I do
not know if this is the correct one.
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mlx4 driver uses the same name for interrupts for every
device in the system. This can make it very confusing trying to work
out exactly which device MSI-X interrupts are for. Change the driver
to add the PCI name of the device to the interrupt name.
Signed-off-by: Arputham Benjamin <abenjamin@sgi.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
On the error path of mlx4_init_hca(), mlx4_close_hca() is called,
followed by mlx4_free_icms() and mlx4_UNMAP_FA(). But both those
functions are also called from mlx4_close_hca(), which leads to a
double free.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current implementation allocates a single host page for EQ context
memory, which was OK when we only allocated a few EQs. However, since
we now allocate an EQ for each CPU core, this patch removes the
hard-coded limit (which we exceed with 4 KB pages and 128 byte EQ
context entries with 32 CPUs) and uses the same ICM table code as all
other context tables, which ends up simplifying the code quite a bit
while fixing the problem.
This problem was actually hit in practice on a dual-socket Nehalem box
with 16 real hardware threads and sufficiently odd ACPI tables that it
shows on boot
SMP: Allowing 32 CPUs, 16 hotplug CPUs
so num_possible_cpus() ends up 32, and mlx4 ends up creating 33 MSI-X
interrupts and 33 EQs. This mlx4 bug means that mlx4 can't even
initialize at all on this quite mainstream system.
Cc: <stable@kernel.org>
Reported-by: Eli Cohen <eli@mellanox.co.il>
Tested-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The old code used two calls to pci_request_region() to get the two BARs
for the mlx4 device, for no particularly good reason. Clean up the code
a little by converting this to a single call to pci_request_regions().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Massage the err_handler upcall into an event handler upcall, pass
netdev port events to the cxgb3 ULPs and generate RDMA port events
based on LLD port events.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds support for legacy SJA1000 CAN controllers on the ISA
or PC-104 bus. The I/O port or memory address and the IRQ number must
be specified via module parameters:
insmod sja1000_isa.ko port=0x310,0x380 irq=7,11
for ISA devices using I/O ports or:
insmod sja1000_isa.ko mem=0xd1000,0xd1000 irq=7,11
for memory mapped ISA devices.
Indirect access via address and data port is supported as well:
insmod sja1000_isa.ko port=0x310,0x380 indirect=1 irq=7,11
Here is a full list of the supported module parameters:
port:I/O port number (array of ulong)
mem:I/O memory address (array of ulong)
indirect:Indirect access via address and data port (array of byte)
irq:IRQ number (array of int)
clk:External oscillator clock frequency (default=16000000 [16 MHz])
(array of int)
cdr:Clock divider register (default=0x48 [CDR_CBP | CDR_CLK_OFF])
(array of byte)
ocr:Output clock register (default=0x18 [OCR_TX0_PUSHPULL])
(array of byte)
Note: for clk, cdr, ocr, the first argument re-defines the default
for all other devices, e.g.:
insmod sja1000_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000
is equivalent to
insmod sja1000_isa.ko mem=0xd1000,0xd1000 irq=7,11 \
clk=24000000,24000000
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Tested-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The member "tx_bytes" of "struct net_device_stats" should be
incremented when the interrupt is done and an "arbitration
lost error" is a TX error and the statistics should be updated
accordingly.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the function can_free_echo_skb to the CAN
device interface to allow upcoming drivers to release echo
skb's in case of error.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed by Stephen Rothwell:
Today's linux-next build (x86_64 allmodconfig gcc-4.4.0)
produced this warning:
drivers/net/wan/dscc4.c: In function 'dscc4_rx_skb':
drivers/net/wan/dscc4.c:670: warning: suggest parentheses around comparison in operand of '|'
which actually points out a bug, I think. It is doing
(x & (y | z)) != y | z
when it probably means
(x & (y | z)) != (y | z)
Introduced by commit 5de3fcab91
("WAN: bit and/or confusion").
Signed-off-by: David S. Miller <davem@davemloft.net>
To unclutter probe() a little bit, put all device initialization code
in one spot and device deinit code in another spot. Also remove unused
rq->buf_index variable/func.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nic firmware can return zero for port MTU, so check for non-zero value
before checking for change in port MTU.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Deprecate some old APIa; change arguments to stats dump all API; add new
interrupt assert API
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provision for multiple Rx/Tx queues. Max of 8 WQs and 8 RQs. Max for
completion queue is 8+8=16 and max for interrupt resources is 8+8+2.
Add driver/firmware interface for setting up RSS secret key and indirection
table.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix: included MAC drops in rx_dropped netstat. Also track Rx trunctations
stat at the MAC
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some driver -> nic firmware calls weren't guarded with a spinlock, exposing
the call i/f to a race between two threads
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enic WQ desc supports a maximum 16K buf size, so split any send fragments
larger than 16K into several descs.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A0 revision ASIC has an erratum on the RQ desc cache on chip where the
cache can become corrupted causing pkt buf writes to wrong locations. The s/w
workaround is to post a dummy RQ desc in the ring every 32 descs, causing a
flush of the cache. A0 parts are not production, but there are enough of
these parts in the wild in test setups to warrant including workaround. A1
revision ASIC parts fix erratum.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nic firmware can place resources (queues, intrs, etc) on multiple BARs, so
allow driver to discover/map resources beyond BAR0.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macvlan devices are currently not multi-queue capable.
We can do that defining rtnl_link_ops method,
get_tx_queues(), called from rtnl_create_link()
This new method gets num_tx_queues/real_num_tx_queues
from lower device.
macvlan_get_tx_queues() is a copy of vlan_get_tx_queues().
Because macvlan_start_xmit() has to update netdev_queue
stats only (and not dev->stats), I chose to change
tx_errors/tx_aborted_errors accounting to tx_dropped,
since netdev_queue structure doesnt define tx_errors /
tx_aborted_errors.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few drivers still access the arguments to MDIO ioctls as an array of
u16. Convert them to use struct mii_ioctl_data.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_ioctl() already checks capable(CAP_NET_ADMIN) before calling the
driver's implementation of MDIO ioctls.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The standard MDIO ioctl numbers are well-established and these should
no longer be needed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While perusing vendor driver, I saw that it did not enable the Vaux
power unless device was able to wake from lan for D3cold.
This might help for Rene's power issue.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a perpetual while() loop in unwinding partial
mapped tx skb on dma mapping failure.
Reported-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicate calls to netxen_napi_add().
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alloc 12k skbuffs so that firmware can aggregate more
packets into one buffer. This doesn't raise memory
consumption since 9k skbs use 16k slab cache anyway.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FCoE DDP in 82599 can be used for both FCoE initiator as well as FCoE
target, depending on the indication of the exchange being the responder or
originator in the F_CTL (frame control) field in the encapsulated Fiber
Channel frame header (T10 Spec., FC-FS). For the initiator, OX_ID is used
for FCoE DDP, where for the target RX_ID is used for FCoE DDP.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a simple selection of a FCoE tx queue based on the current cpu id to
distribute transmission of FCoE traffic evenly among multiple FCoE transmit
queues.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for multiple transmit queues to the Fiber Channel
over Ethernet (FCoE) feature found in 82599. Currently, FCoE has multiple
Rx queues available, along with a redirection table, that helps distribute
the I/O load across multiple CPUs based on the FC exchange ID. To make
this the most effective, we need to provide the same layout of transmit
queues to match receive.
Particularly, when Data Center Bridging (DCB) is enabled, the designated
traffic class for FCoE can have dedicated queues for just FCoE traffic,
while not affecting any other type of traffic flow.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates things so that vlan tags are taken into account when
setting the receive large packet maximum length. This allows the VF driver
to correctly receive full sized frames when vlans are enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb_irq_disable/enable calls were causing virtual functions associated
with the igb physical function to have their interrupts disabled. In order
to prevent this from occuring we should only clear/set the bits related to
the physical function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the set_rx_mode netdevice operation so that igb
can better support multiple unicast addresses.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_mii, fec_enet_rx and fec_enet_tx are both only called by
fec_enet_interrupt in interrupt context. So they must not use
spin_lock_irq/spin_unlock_irq.
This fixes:
WARNING: at kernel/lockdep.c:2140 trace_hardirqs_on_caller+0x130/0x194()
...
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Matt Waddel <Matt.Waddel@freescale.com>
Cc: netdev@vger.kernel.org
Cc: Tim Sander <tim01@vlsi.informatik.tu-darmstadt.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii_discover_phy is only called by fec_enet_mii (via mip->mii_func). So
&fep->mii_lock is already held and mii_discover_phy must not call
mii_queue which locks &fep->mii_lock, too.
This was noticed by lockdep:
=============================================
[ INFO: possible recursive locking detected ]
2.6.31-rc8-00038-g37d0892 #109
---------------------------------------------
swapper/1 is trying to acquire lock:
(&fep->mii_lock){-.....}, at: [<c01569f8>] mii_queue+0x2c/0xcc
but task is already holding lock:
(&fep->mii_lock){-.....}, at: [<c0156328>] fec_enet_interrupt+0x78/0x460
other info that might help us debug this:
2 locks held by swapper/1:
#0: (rtnl_mutex){+.+.+.}, at: [<c0183534>] rtnl_lock+0x18/0x20
#1: (&fep->mii_lock){-.....}, at: [<c0156328>] fec_enet_interrupt+0x78/0x460
stack backtrace:
Backtrace:
[<c00226fc>] (dump_backtrace+0x0/0x108) from [<c01eac14>] (dump_stack+0x18/0x1c)
r6:c781d118 r5:c03e41d8 r4:00000001
[<c01eabfc>] (dump_stack+0x0/0x1c) from [<c005bae4>] (__lock_acquire+0x1a20/0x1a88)
[<c005a0c4>] (__lock_acquire+0x0/0x1a88) from [<c005bbac>] (lock_acquire+0x60/0x74)
[<c005bb4c>] (lock_acquire+0x0/0x74) from [<c01edda8>] (_spin_lock_irqsave+0x54/0x68)
r7:60000093 r6:c01569f8 r5:c785e468 r4:00000000
[<c01edd54>] (_spin_lock_irqsave+0x0/0x68) from [<c01569f8>] (mii_queue+0x2c/0xcc)
r7:c785e468 r6:c0156b24 r5:600a0000 r4:c785e000
[<c01569cc>] (mii_queue+0x0/0xcc) from [<c0156b78>] (mii_discover_phy+0x54/0xa8)
r8:00000002 r7:00000032 r6:c785e000 r5:c785e360 r4:c785e000
[<c0156b24>] (mii_discover_phy+0x0/0xa8) from [<c0156354>] (fec_enet_interrupt+0xa4/0x460)
r5:c785e360 r4:c077a170
[<c01562b0>] (fec_enet_interrupt+0x0/0x460) from [<c0066674>] (handle_IRQ_event+0x48/0x120)
[<c006662c>] (handle_IRQ_event+0x0/0x120) from [<c0068438>] (handle_level_irq+0x94/0x11c)
...
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Matt Waddel <Matt.Waddel@freescale.com>
Cc: netdev@vger.kernel.org
Cc: Tim Sander <tim01@vlsi.informatik.tu-darmstadt.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpq ether driver is modifying the data art of the skb by first
dropping the KISS byte (a command byte for the radio) then prepending the
length + 4 of the remaining AX.25 packet to be transmitted as a little
endian 16-bit number. If the high byte of the length has a different
value than the dropped KISS byte users of clones of the skb may observe
this as corruption. This was observed with by running listen(8) -a which
uses a packet socket which clones transmit packets. The corruption will
then typically be displayed for as a KISS "TX Delay" command for AX.25
packets in the range of 252..508 bytes or any other KISS command for
yet larger packets.
Fixed by using skb_cow to create a private copy should the skb be cloned.
Using skb_cow also allows us to cleanup the old logic to ensure sufficient
headroom in the skb.
While at it, replace a return of 0 from bpq_xmit with the proper constant
NETDEV_TX_OK which is now being used everywhere else in this function.
Affected: all 2.2, 2.4 and 2.6 kernels.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Jann Traschewski <jann@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Request_irq() may fail in different ways, handle accordingly.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Neil Horman <nhorman@txudriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change it to a menuconfig to give it some documentation, to
refer users to our wireless wiki for extra resources and
documentation. It seems our wiki is still obscure to some.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to put ethtool_ops in data, they should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.102.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717 is a dual port chip that has a shared MDIO bus design. While
it is impossible for one function to interface with the wrong phy, that
function still needs to know which MDIO bus address to use when
interfacing with its own phy. This patch adds code to determine which
MDIO bus address to use.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds NVRAM detection routines for the 5717.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 5717 asic rev.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RSS is enabled, the status block format changes slightly. The
"rx_jumbo_consumer", "reserved", and "rx_mini_consumer" members get
mapped to the other three rx return ring producer indexes. This patch
introduces a new per-interrupt member which identifies which location
in the status block a particular vector should look for return ring
updates.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multivector RSS is enabled, the first interrupt vector is only used
to report link interrupts and error conditions. This patch changes the
code so that rx and tx ring resources are not allocated for this vector.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code needed to enable RSS.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to tune the coalescing parameters for the other
msix vectors.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to enable and disable the rest of the NAPI
instances.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exposes the additional transmit rings to the kernel and makes
the necessary modifications to transmit, open, and close paths.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes up two spots that need attention now that msix support
has been added.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to assign status block, tx producer ring and rx
return ring resources needed for the other interrupt vectors.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717 assigns mailbox locations to interrupt vectors in a rather
non-intuitive way. (Much of the complexity stems from legacy
compatibility issues.) This patch implements the assignment scheme.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds MSI-X support.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to support multiple interrupt vectors around the
kernel's interrupt API.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves most of the chip ring setup logic into a separate
function. This will make it easier to verify the multi ring setup
changes.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each interrupt vector has its own bit in the host coalescing register to
force that vector's status block to be updated and generate an
interrupt. This patch adds a member to the per-interrupt structure
that records which bit belongs to that vector.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch inlines the code of tg3_cond_int() into the function's only
callsite. This prep work makes the following patch cleaner.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aup->mii_bus->irq allocation may fail, prevent a dereference of NULL.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
B0_CTST is a 24bit register according to the vendor driver (sk98lin).
A 16bit read on B0_CTST will always return 0 for Y2_VAUX_AVAIL (1<<16),
so use a 32bit read when testing Y2_VAUX_AVAIL
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor similar two sections of code that free buffers into one.
Only call tx_init if all buffer allocations succeed.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Observed by Mike McCormack.
The LED bit here is just a software controlled value used to
turn on one of the LED's on some boards. The register value was wrong,
which could have been causing some power control issues.
Get rid of problematic define use the correct mask.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As tun always has an embeedded struct sock,
use sk and sk_receive_queue fields instead of
duplicating them in tun_struct.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can speedup ether addresses compares using compare_ether_addr_64bits()
instead of memcmp(). We make sure all operands are at least 8 bytes long and
16bits aligned (or better, long word aligned if possible)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To speedup ether addresses compares, we can use compare_ether_addr_64bits()
(all operands are guaranteed to be at least 8 bytes long)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 82599 multi speed fiber case when driver is loaded without any
cable and reconnecting the cable with a 1G partner does not bring
up the link in 1Gb mode. When there is no link we first setup the link
at 10G & 1G and then try to re-establish the link at highest speed 10G
and thereby changing autoneg_advertised value to highest speed 10G.
After connecting back the cable to a 1G link partner we never try 1G
as autoneg advertised value is changed to link at 10G only. The
following patch fixes the issue by properly initializing the
autoneg_advertised value just before exiting from link setup routine.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When disabling the Rx and Tx data arbiters prior to configuration changes,
the arbiters were not being shut down properly. This can create a race
in the DCB hardware blocks, and potentially hang the arbiters. Also, the
Tx descriptor arbiter shouldn't be disabled when applying configuration
changes; disabling this arbiter can cause a Tx hang.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link code cleanup: a number of redundant functions and MAC variables are cleaned up,
with some functions being consolidated into a single-purpose code path.
Removed following deprecated link functions and mac variables
* ixgbe_setup_copper_link_speed_82598
* ixgbe_setup_mac_link_speed_multispeed_fiber
* ixgbe_setup_mac_link_speed_82599
* mac.autoneg, mac.autoneg_succeeded, phy.autoneg_wait_to_complete
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling VLAN filters (VFE) when the primary interface is brought up
(per commit 78ed11a) has caused problems for some users who manage
their systems using IPMI over a VLAN. This is because when the driver
enables the VLAN filter, this same filter table is enabled for the
management channel, and the table is initially empty, which means that
the IPMI/VLAN packets are filtered out and not received by the BMC.
This is a problem only on e1000 class adapters, as it is only
on e1000 that the filter table is common to the management and host
streams.
With this change, filtering is only enabled when one or more host VLANs
exist, and is disabled when the last host VLAN is removed. VLAN filtering
is always disabled when the primary interface is in promiscuous mode,
and will be (re)enabled if VLANs exist when the interface exits
promiscuous mode.
Note that this does not completely resolve the issue for those using VLAN
management, because if the host adds a VLAN, then the above problem
occurs when that VLAN is enabled. However, it does mean the there is no
problem for configurations where management is on a VLAN and the host is
not.
A complete solution to this issue would require further driver changes.
The driver would need to discover if (and which) management VLANs are
active before enabling VLAN filtering, so that it could ensure that the
managed VLANs are included in the VLAN filter table. This discovery
requires that the BMC identifies its VLAN in registers accessible
to the driver, and at least on Dell PE2850 systems the BMC does not
identify its VLAN to allow such discovery. Intel is pursuing this issue
with the BMC vendor.
Signed-off-by: Dave Graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to check what was the last fw error we got accross resets, we add
this debugfs entry. It displays the complete ASSERT information.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When UMAC stalls or asserts, we want to reset the device. But when we're
associated, the current reset worker will end up calling
cfg80211_connect_result() with the cfg80211 sme layer knowing that we're
reassociating. That ends up with some ugly warnings.
With this patch we're telling the upper layer that we've roamed if
reassociation succeeds, and that we're disconnected if it fails.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The LMAC calibration API got broken mostly by having a configuration bitmap
being different than the result one.
This patch tries to address that issue by correctly running calibrations with
the newest firmwares, and keeping a backward compatibility fallback path for
older firmwares, where the configuration and result bitmaps were identical.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also mark some functions static.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver receives "connection terminated" event from device,
it could be caused by 2 reasons: the firmware is roaming or the
connection is lost (AP disappears). For the former, an association
complete event is supposed to come within 3 seconds. For the latter,
the driver won't receive any event except the connection terminated.
So we kick a delayed work (5*HZ) when we receive the connection
terminated event. It will be canceled if it turns out to be a roaming
event later. Otherwise we notify SME and userspace the disconnection.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The device sends connection terminated and [re]association success
(or failure) events when roaming occours. The patch uses
cfg80211_roamed instead of cfg80211_connect_result to notify SME
for roaming.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwm_cfg80211_get_station() should be static.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connect is called with the LEGACY_PSK authentication type set, and a
proper sme->key, we need to set the WEP key straight after setting the
profile otherwise the authentication will never start.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If cfg80211 requests to connect when we have already had an active
profile, invalidate the current profile first before sending a new
profile to UMAC.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since rndis_wlan is now converted to cfg80211, WIRELESS_EXT isn't
required anymore.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- remove double newlines between functions
- remove commented out function (rndis_set_config_parameter_u32())
- coding style fix in rndis_set_config_parameter_str()
- add comment banners between function sections
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As generic hw timer interrupt handler is moved to tasklet,
we no more need to call spin_lock_irqsave().
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no point handling this in hard irq, move it to
tasklet.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for dcbnl_rtnl_ops.setapp/getapp to set or get the current user
priority bitmap for the given application protocol. Currently, 82599 only
supports setapp/getapp for Fiber Channel over Ethernet (FCoE) protocol.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support to the net_device_ops.ndo_fcoe_enable/disable for 82599. This
consequently allows us to dynamically turn FCoE offload feature on or off
upon incoming calls to ndo_fcoe_enable/disable. When this happens, FCoE offload
features are enabled/disabled accordingly, and this is regardless of whether
DCB being turned on or not.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a couple of cases collapse some extra code like:
int retval = NETDEV_TX_OK;
...
return retval;
into
return NETDEV_TX_OK;
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly just simple conversions:
* ray_cs had bogus return of NET_TX_LOCKED but driver
was not using NETIF_F_LLTX
* hostap and ipw2x00 had some code that returned value
from a called function that also had to change to return netdev_tx_t
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of some bogus return wrapping as well.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are all drivers that don't touch real hardware.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update all the pcmcia network drivers for netdev_tx_t.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TUN driver lacks any LSM hooks which makes it difficult for LSM modules,
such as SELinux, to enforce access controls on network traffic generated by
TUN users; this is particularly problematic for virtualization apps such as
QEMU and KVM. This patch adds three new LSM hooks designed to control the
creation and attachment of TUN devices, the hooks are:
* security_tun_dev_create()
Provides access control for the creation of new TUN devices
* security_tun_dev_post_create()
Provides the ability to create the necessary socket LSM state for newly
created TUN devices
* security_tun_dev_attach()
Provides access control for attaching to existing, persistent TUN devices
and the ability to update the TUN device's socket LSM state as necessary
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: Eric Paris <eparis@parisplace.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Morris <jmorris@namei.org>
Doing an RTC reset when DMA is active may corrupt memory,
make sure no DMA is active at this moment by doing an
AHB reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old function rt2x00queue_payload_align() handled
both adding and removing L2 padding and some basic
frame alignment. The entire function was being abused
because it had multiple functions and the header length
argument was somtimes used to align the header instead
of the payload.
Additionally there was a bug when inserting L2 padding
that only the payload was aligned but not the header. This
happens when the header wasn't aligned properly by mac80211,
but rt2x00lib only moves the payload.
A secondary problem was that when removing L2 padding during
TXdone or RX the skb wasn't resized to the proper size.
Split the function into seperate functions each handling
its task as it should.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not all values of the TX status enumeration were
covered during updating of the TX statistics. This
could lead to wrong bitrate tuning but also wrong
behavior in tools like hostapd.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rev1 2GHz and rev2 5GHz gain tables were incorrectly documented
on the specs originally. Update these gaintables to match the cor-
rected specs.
Signed-off-by: Gábor Stefanik <netroller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also mark the LP-PHY driver "802.11a/g" instead of "802.11g",
as LP-PHY is capable of both 2GHz and 5GHz operation.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-Make use of the b43_phy_set/mask/maskset helpers.
-Fix a few errors in the code.
-Make the code more readable.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Significant literature suggests users use debug flags 0x43fff - this causes
the debug flags to be set that causes information to be printed for every
received frame - including beacons. In the best case it fills up the logs,
at worst it slows driver down and causes failures due to timeouts.
In the RX handler, print debugging only if user requested RX debugging.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 does not have update_chain_flags defined and because if this we always
see the debug message that does not apply to it. Add a check to be specific
about what is actually happening.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some concerns were raised about the automatic adjustment
of sleep intervals to all the same, potentially high,
value, and I can imagine the hardware behaving better
when we don't ask too much of it.
So let's convert to use a succession of sleep levels
when requesting to go to deeper sleeps (which can only
happen with large DTIM intervals), using the succession
values from power level three, which have the benefit of
also having been tested extensively already.
As a result, the automatic sleep level adjustment will
now be mostly equivalent to power level three, except
for the RX/TX timeouts and possibly using smaller sleep
vectors to account for networking latency.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For HT packets, mac80211 expects the rate_idx to be an MCS number, which is the
lower byte of rate_n_flags. However, iwl_hwrate_to_plcp_idx takes the MCS
number and reduces it down to the range 0-8 (6 to 60 Mbps), removing the bits
that signify multiply streams, HT40 Duplicate mode, or unequal modulation.
This version is used for various internal purposes through the driver.
Add the function iwl_hwrate_get_mac80211_idx, an alternate version which takes
the rate and the band and returns the mac80211 index (MCS, for HT packets, and
PLCP rate, for legacy packets).
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Refactor and correct rate selection for outgoing transmitted
packets.
First, note that HT rates in the mac80211 rate table do not provide valid
indices when ieee80211_get_tx_rate is called; the check to see if we could to
abort a transmission early in iwl_tx_skb() would thus occasionally read invalid
memory and occasionally stall transmission (if the erroneous byte was 0xff).
We remove that code; the check wasn't valid anyway.
Second, iwl_tx_cmd_build_rate() also called ieee80211_get_tx_rate to be used
for sending management packets, which do not use the uCode station table. This
patch refactors that function and adds comments to enhance legibility, replaces
the call to ieee80211_get_tx_rate() with a direct lookup, and adds error
handling in case the table entry is invalid.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_supported_band is supposed to only contain legacy rates in the
bitrates table (HT rates go in the ieee80211_sta_ht_cap substruct). Make
iwlwifi driver obey this restriction by removing the 60 Mbps rate. Also, clean
up a few pieces of other code that formerly relied on 60 Mbps being in
sband->bitrates.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If autonegotiation was disabled, we still set the
BMCR_ANENABLE and BMCR_ANRESTART, which resulted in autonegotiation
never being disabled.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reported-by: Julia Lawall <julia@diku.dk>
Single line log messages should be emitted by a single call
where possible.
Converted multiple calls to DBG_PRINT to single call form.
Removed "s2io:" preface from DBG_PRINTs.
The DBG_PRINT macro now emits a log level and is surrounded by
a do {...} while (0)
All s2io log output is now prefaced with KBUILD_MODNAME ": "
via pr_fmt.
The DBG_PRINT macro should probably be converted to use the
dev_<level> form eventually.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missed doing the conversion in earlier patch.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regularize the declaration and uses of
struct config_param *config = &sp->config;
struct mac_info *mac_control = &sp->mac_control;
and use
struct stat_block *stats = mac_control->stats_info;
struct swStat *swstats = &stats->sw_stat;
struct xpakStat *xstats = &stats->xpak_stat;
and convert the longish uses like
nic->mac_control.stats_info->sw_stat.<foo>
to
swstats-><foo>
etc.
This also makes the statistics code marginally smaller
and presumably faster.
Old:
$ size s2io.o
text data bss dec hex filename
114289 516 33360 148165 242c5 s2io.o
New:
$ size s2io.o
text data bss dec hex filename
114097 516 33360 147973 24205 s2io.o
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed trivial typo as well
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Still has a few long lines.
checkpatch was:
total: 263 errors, 53 warnings, 8751 lines checked
is:
total: 4 errors, 35 warnings, 8767 lines checked
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use consistent style. Don't calculate the kmalloc size multiple times
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Repeated variable use and line wrapping is hard to read.
Use temp variables instead of direct references.
struct fifo_info *fifo = &mac_control->fifos[i];
struct ring_info *ring = &mac_control->rings[i];
struct tx_fifo_config *tx_cfg = &config->tx_cfg[i];
struct rx_ring_config *rx_cfg = &config->rx_cfg[i];
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the tests that check whether Frame* bits are not set
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements suspend/resume and WOL support for UCC Ethernet
driver.
We support two wake up events: wake on PHY/link changes and wake
on magic packet.
In some CPUs (like MPC8569) QE shuts down during sleep, so magic packet
detection is unusable, and also on resume we should fully reinitialize
UCC structures.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes currently unused UGETH_MAGIC_PACKET Kconfig symbol
and code, i.e. magic_packet_detection_{enable,disable} functions.
The two functions each contain just two steps that we'll place into
suspend/resume code path under CONFIG_PM.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch factors out MAC initialization into ucc_geth_init_mac()
function that we'll use for suspend/resume.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 3e73fc9a12 ("ucc_geth: Fix IO
memory (un)mapping code") I fixed ug_regs IO memory leak by properly
freeing the allocated memory. But ethtool_stats() callback doesn't
check for ug_regs being NULL, and that causes following oops if
'ethtool -S' is executed on a closed eth device:
Unable to handle kernel paging request for data at address 0x00000180
Faulting instruction address: 0xc0208228
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c0208228] uec_get_ethtool_stats+0x38/0x140
LR [c02559a0] ethtool_get_stats+0xf8/0x23c
Call Trace:
[ef87bcd0] [c025597c] ethtool_get_stats+0xd4/0x23c (unreliable)
[ef87bd00] [c025706c] dev_ethtool+0xfe8/0x11bc
[ef87be00] [c0252b5c] dev_ioctl+0x454/0x6a8
...
---[ end trace 77fff1162a9586b0 ]---
Segmentation fault
This patch fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the tx_prod, tx_cons, tx_pending, tx_ring, and
tx_buffers transmit ring device members to a per-interrupt structure.
It also adds a new transmit producer mailbox member (prodmbox) and
converts the code to use it rather than a preprocessor constant.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the rx_rcb, rx_rcb_mapping, and rx_rcb_ptr return ring
device members to a per-interrupt structure. It also adds a new return
ring consumer mailbox register member (consmbox) and converts the code
to use it rather than a preprocessor constant.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the last_tag, last_tag_irq, and hw_status device
members to a per-interrupt structure. It also adds a new interrupt
mailbox member (int_mbox) and converts the code to use it rather than a
direct preprocessor constant.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the napi interrupt handler functions to accept and
use tg3_napi structures.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch migrates the ISR parameter from struct net_device to struct
tg3_napi. Checkpatch complains about the existence of the preexisting
IRQF_SAMPLE_RANDOM flag. I've opted to keep this patch conservative and
let it continue to exist until the flag gets officially purged from the
kernel.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a per-interrupt data structure, moves the napi
member over, and creates a tg3 pointer back to the device structure.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Later patches will be adding MSIX support, which will complicate
interrupt initialization. This patch prepares for the integration by
breaking out the interrupt setup and teardown code into separate
functions and cleaning up the error return paths.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717 only uses extended buffer descriptors for the jumbo producer
ring. Extended buffer descriptors are available on all devices that
support a separate jumbo producer ring so make the change universal.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch migrates most of the rx producer ring variables to a new
tg3_rx_prodring_set structure and modifies the code accordingly.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Later patches are going to complicate the ring initialization routines.
This patch breaks out the setup and teardown of the rx producer rings
into separate functions to make the code more readable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch attempts to document the various rx buffer sizes used by the
driver and how they relate to each other.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves where the jumbo capable and msi support flags are
located. This is prep work for the addition of msix support flags.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch separates the code that sets up the mini producer ring from
the code that sets up the jumbo producer rings. The 5717 asic rev
devices do not have a mini ring, but do have a jumbo frame
implementation similar to the 5704 and previous devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes up the NVRAM detection switch statements to conform
to the kernel coding style.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new device ID for those 5785 devices that will only
use 10/100 phys.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device firmware uses the MDIO bus during early setup. If the driver
modifies the MDIO bus configuration while it is in use by the firmware,
any number of bad things can happen. This patch delays MDIO setup until
after the firmware posts its magic signature, signifying initialization
is complete.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method of ETHER_LINK pin is board dependence.
This patch adding paramters are:
- no_ether_link : If set to 1, do not use ETHER_LINK
- ether_link_active_low : If set to 1, ETHER_LINK is active low.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On TI's DA850/OMAP-L138 EVM, MAC address is stored in SPI
flash which is accessed using MTD interface.
This patch delays the initialization of DaVinci EMAC driver
by changing module_init to late_initcall. This helps SPI and
MTD drivers to get initialized before EMAC thereby enabling
EMAC driver to read the MAC address while booting and use it.
Tested with NFS on DM644x, DM6467, DA830/OMAP-L137 and
DA850/OMAP-L138 EVMs.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Reviewed-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Better small packet receive performance.
- Better handling of Flow control on 5709.
- Fixed iSCSI TMP ABORT TASK problem.
- Added iSCSI TCP timestamp option.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow the 10G iSCSI code to reuse the function.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow the 10G iSCSI code to reuse the function.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX completions were running in a workqueue queued by the ISR. This
patch moves the processing of TX completions to an existing RSS NAPI
context.
Now each irq vector runs NAPI for one RSS ring and one or more TX
completion rings.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we downshift to MSI/Legacy if we don't get enough vectors for
cpu_count RSS rings plus cpu_count TX completion rings. This patch
allows running MSIX with the vector count that the platform provides.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we have three types of RX rings.
1) Default ring - services rx_ring for broadcast/multicast, handles
firmware events, and errors.
2) TX completion ring - handles only outbound completions.
3) RSS ring - handles only inbound completions.
This patch gets rid of the default ring type and moves it's functionality
into the first RSS ring. This makes better use of MSIX vectors since
they are a limited resource on some platforms.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bonding: Have bond_check_dev_link examine netif_running
Some network devices do not call netif_carrier_off when they
are set administratively down. Have the bonding link check function
also inspect the netif_running state. Ignore netif_running if the
bond_check_dev_link function is called with "reporting" set, as in that
case it's inspecting the capabilities of the non-netif_carrier device
driver.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
max_bonds is of type int and cannot be greater than INT_MAX.
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bonding can use compare_ether_addr() in bond_release.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propogate the vlan_features of the slave devices to the bonding
master device, using the same logic as for regular features.
Tested by Or Gerlitz <ogerlitz@voltaire.com>, who also removed
the debug logic from the original test patch.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the places in debugfs.c are missing a NULL check on the return value of
get_zeroed_page API call. Added required NULL check at appropriate places.
Signed-off-by: Kiran Divekar <kirandivekar@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that cfg80211 functions are added and wext converted to use wext-compat
functions, remove wext structures and disabled code.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stats worker no longer poll stats from device anymore. It's still
needed to poll device control channel for connect/disconnect events,
so rename stats worker as device poller.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add cfg80211 get_station and convert SIOCGIWRATE and get_wireless_stats
to cfg80211.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add cfg80211 add_key/del_key/set_default_key and convert wext to use theim.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add cfg80211 set_channel and convert wext to use it.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add cfg80211 connect functions for station and ad-hoc modes and
convert wext to use theim.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Random essid must be set to turn on radio when not connected. If device is
in ad-hoc mode, this results 'media connect' indications with the random
essid which should be ignored.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use is_zero_ether_addr() and is_broadcast_ether_addr() instead of
memcmp against ffff_bssid/zero_bssid.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move link up/down work to separate functions and use local array
for allocating memory for info structure instead of kzmalloc.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase scan delay from 1 sec to 6 sec. Spec says that scan by
OID_802_11_BSSID_LIST_SCAN completes in 6 seconds.
Before rfkill patch too short delay was not problem as device was
always active (radio on) and performing background scanning.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Buffer used for bssid list might be too small. Change rndis_query_oid()
to return required buffer length to caller and make rndis_check_bssid_list()
resize buffer when needed.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
OID_802_11_BSSID_LIST_SCAN clears device's bssid list, so retrieve
current bssid list from device before issuing new scan.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting WPA keys with OID_802_11_ADD_KEY sometimes trigger
instant media connect indication. These indications are extranous and
should be ignored, as otherwise driver would send reassociation event to
userspace which in this case is not needed.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The A/G-PHY changes are fallout fixes from the enum change,
which in turn allows the LP-PHY code to be much simpler.
The antenna_to_phyctl change is a fix for a potential
existing bug that this patch may otherwise trigger.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The most common LP-PHY device, BCM4312, is now fully functional.
So, no need to say "probably won't work for you" anymore.
It's also not "for debuggers and developers only", as it is
perfectly usable for end-users now (at least for BCM4312).
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR5K_SREV is available even if the chip has been put to sleep. Relying
on the chip register allows binding non-standard PCI IDs by
echo VENDOR_ID PRODUCT_ID >/sys/bus/pci/drivers/ath5k/new_id
without having to specify the driver data as well.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The `val' variable in ath5k_eeprom_read_turbo_modes() is used
uninitialized. gcc 4.4.1 with -fno-inline-functions-called-once reports
it:
eeprom.c: In function 'ath5k_eeprom_read_turbo_modes':
eeprom.c:441: warning: 'val' may be used uninitialized in this function
Comparing the code to the Atheros HAL, it's clear that the split between
ath5k_eeprom_read_modes() and ath5k_eeprom_read_turbo_modes() was
incorrect.
The Atheros HAL reads both turbo and non-turbo data from EEPROM in one
function. Some turbo mode parameters are derived from the same EEPROM
values as non-turbo parameters, just from different bits.
Merge ath5k_eeprom_read_turbo_modes() into ath5k_eeprom_read_modes() to
fix the warning. The actual values and offsets have been cross-checked
against Atheros HAL.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As Pavel Roskin noted, the check for mac version as copied from
legacy_hal made no sense. This replaces it with the equivalent
and makes up a suitable #define for the mac version legacy_hal
checked.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After some discussion on IRC about the PHY register write change,
I am not sure anymore if this is the right thing to do.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ICT IRQ table is a set of __le32 values, not u32 values,
so when reading it we need to take into account that it has
to be converted to CPU endianness. This was causing a lot of
trouble on my powerpc box where various things would simply
not work for no apparent reason with 5xxx cards, but worked
with 4965 -- which doesn't use the ICT table.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since patch "rt2x00: bss_info_changed() callback is allowed to sleep" the
variable delayed wasn't used anymore. This means it can be removed
along with the call to schedule_work which depended on that variable.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement the "PMU LDO set voltage" and "PMU LDO PA ref enable"
functions, and use them during LP-PHY baseband init in b43.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-Fix a few nasty typos (b43_phy_* operations instead of b43_radio_*)
in the channel tune routines.
-Fix some typos & spec errors found by MMIO tracing.
-Optimize b43_phy_write & b43_phy_mask/set/maskset to use
only the minimal number of MMIO accesses. (Write is possible
using a single 32-bit MMIO write, while set/mask/maskset can
be done in 3 16-bit MMIOs).
-Set the default channel back to 1, as the bug forcing us to use
channel 7 is now fixed.
With this, the device comes up, scans, associates, transmits,
receives, monitors and injects on all channels - in other words,
it's fully functional. Sensitivity and TX power are still sub-optimal,
due to the lack of calibration (that's next on my list).
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Qdiv roundup routine is essentially a fixed-point
division algorithm, using only integer math.
However, the version in the specs had a major error
that has been recently fixed (a missing quotient++).
Replace Qdiv roundup with a rewritten, simplified version.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change implements rfkill support for RTL8187B and RTL8187L devices,
using new cfg80211 rfkill API.
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds 3-wire bluetooth coex support for AR9285.
This support can be enabled through btcoex_enable modparam.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need a hw cap bit for btcoex anymore as btcoex scheme type
is enough to do this.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also define macros for wlanactive and btactive (5 & 6) gpios.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure btcoex register configured with appropriate values
after it is initialized with the default values from initvals.h
during reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
