When running with OP-TEE, the suspend control is handled securely.
Suspend can be entered using PSCI support. Since the sama5d2 supports
multiple suspend modes, add a new CONFIG_ATMEL_SECURE_PM which will
send a SMC call to select the suspend mode at init time.
"atmel.pm_modes" boot argument is still supported for compatibility
purposes but the standby value is actually ignored since PSCI suspend
is used and it only support one mode (suspend).
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Since OP-TEE now has a more complete support for sama5d2, add necessary
code to perform SMC calls. The detection of OP-TEE is based on a
specific device-tree node path (/firmware/optee) such has done by some
other SoC. A check is added to avoid doing SMC calls without having
OP-TEE.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Implement PIT64B selection thus it will be available for the necessary
targets (at the moment SAM9X60 and SAMA7G5) w/o the necessity to
specify it via defconfig. With this the current CONFIG_TIMER_OF
dependency of PIT64B driver could be removed.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
SoCs supporting ULP0 or ULP1 modes and variants of Cadence Ethernet IP
(controlled by macb driver) may behave buggy when Wake-on-Lan (WoL) is
configured and WoL packet is received while in ULP0/ULP1. On some SoCs
Ethernet interface is not working after resume. On other SoCs the CPU
goes to abort on resume path when switching execution from internal SRAM
to DRAM. For ULP1 + WoL the issue is related a particular restart
sequence of the internal clocks when resuming. These clocks are
automatically managed by PMC and may happen that GMAC peripheral clock
is restarted few clock cycles before internal clocks causing blocking
of Ethernet's DMA. As a consequence Ethernet TX transactions are stopped
and RX transactions are partially stopped (packets are received by MAC,
RX counters incremented but the data is not transferred to DRAM). The
workaround for this is to disable Ethernet's peripheral clock when
going to ULP1. Same behavior has been reproduced on ULP0 for some
platforms (SAMA5D2, SAMA5D3) and the same workaround solves the issue.
The problem has been solved on pm.c as quirk to avoid polluting the
MACB driver with AT91 specific issues as this driver is generic to
multiple vendors.
At probe pointers to struct device_node are retrieved and on the
at91_pm_enter() the quirk specifics are applied: for all Ethernet
interfaces that were parsed the peripheral clocks are disabled. A
special handling is done for modes in dns_modes mask as these are
considered modes that blocks the system if WoL packet are received
but for which applying quirk will lead to not waking up on WoL
packets: in situation where Ethernet interface(s) has suspend mode
in dns_modes mask and Ethernet interface(s) is the only available
wakeup source the suspend is canceled.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Use kernel documentation style. Along with it fix the naming of
struct at91_pm_sfrbu_regs in documentation.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Introduce macros to replace standby/suspend mode if they depends on
controllers that failed to map (or other errors). Macros keep track
of the complementary mode to avoid having set the same AT91 PM mode
for both suspend and standby.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Move documentation of bu to keep the same order as in the structure
itself.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Add CPU idle support for SAMA7G5. Support will make use of PMC_CPU_RATIO
register to divide the CPU clock by 16 before switching it to idle and
use automatic self-refresh option of DDR controller.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220113144900.906370-5-claudiu.beznea@microchip.com
Fix following coccicheck warning:
./arch/arm/mach-at91/pm.c:643:1-33: WARNING: Function
for_each_matching_node_and_match should have of_node_put() before goto
Early exits from for_each_matching_node_and_match should decrement the
node reference counter.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20211014084555.21422-1-wanjiabing@vivo.com
The SoC updates this time are mainly removing obsolete code from the
OMAP2 platform, another step in the eternal cleanup of that platform.
There are two new SoCs getting added: STMicroelectronics stm32mp13 and
Microchip lan966. Both fit into existing platforms and require minimal
changes here.
A couple of MAINTAINER file updates relate to those changes, and
update some file paths.
-----BEGIN PGP SIGNATURE-----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=Vkfc
-----END PGP SIGNATURE-----
Merge tag 'soc-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"The SoC updates this time are mainly removing obsolete code from the
OMAP2 platform, another step in the eternal cleanup of that platform.
There are two new SoCs getting added: STMicroelectronics stm32mp13 and
Microchip lan966. Both fit into existing platforms and require minimal
changes here.
A couple of MAINTAINER file updates relate to those changes, and
update some file paths"
* tag 'soc-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (28 commits)
MAINTAINERS: Update BCM7XXX entry with additional patterns
MAINTAINERS: add pinctrl-apple-gpio to ARM/APPLE MACHINE
MAINTAINERS: Add pasemi i2c to ARM/APPLE MACHINE
ARM: SPEAr: Update MAINTAINERS entries
ARM: OMAP2+: Drop unused CM defines for am3
ARM: OMAP2+: Drop unused CM and SCRM defines for omap4
ARM: OMAP2+: Drop unused CM and SCRM defines for omap5
ARM: OMAP2+: Drop unused CM defines for dra7
ARM: OMAP2+: Drop unused PRM defines for am3
ARM: OMAP2+: Drop unused PRM defines for am4
ARM: OMAP2+: Drop unused PRM defines for omap4
ARM: OMAP2+: Drop unused PRM defines for omap5
ARM: OMAP2+: Drop unused PRM defines for dra7
ARM: OMAP2+: Fix comment typo
ARM: OMAP2+: Fix typo in some comments
ARM: at91: add basic support for new SoC family lan966
dt-bindings: arm: at91: Document lan966 pcb8291 and pcb8290 boards
ARM: at91: Documentation: add lan966 family
ARM: at91: Documentation: add sama7g5 family
MAINTAINERS: add an entry for NXP S32G boards
...
This patch introduces Microchip LAN966 ARMv7 based SoC family
of multiport gigabit AVB/TSN-capable ethernet switches.
It supports two SKUs: 4-port LAN9662 with multiprotocol
processing support and 8-port LAN9668 switch.
LAN966 family includes copper and serial ethernet interfaces,
peripheral interfaces such as PCIe, USB, TWI, SPI, UART, QSPI,
SD/eMMC, Parallel Interface (PI) as well as synchronization
and trigger inputs/outputs.
Signed-off-by: Kavyasree Kotagiri <kavyasree.kotagiri@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
[nicolas.ferre@microchip.com: merged patches for this SoC introduction]
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210831102138.2476-1-kavyasree.kotagiri@microchip.com
Link: https://lore.kernel.org/r/20211004105926.5696-5-kavyasree.kotagiri@microchip.com
In suspend/resume procedure for AT91 architecture different controllers
(PMC, SHDWC, RAM, RAM PHY, SFRBU) are accessed to do the proper settings
for power saving. Commit f0bbf17958 ("ARM: at91: pm: add self-refresh
support for sama7g5") introduced the access to RAMC PHY controller for
SAMA7G5. The access to this controller is done after RAMC ports are
closed, thus any TLB walk necessary for RAMC PHY virtual address will
fail. In the development branch this was not encountered. However, on
current kernel the issue is reproducible.
To solve the issue the previous mechanism of pre-loading the TLB with
the RAMC PHY virtual address has been used. However, only the addition
of this new pre-load breaks the functionality for ARMv5 based
devices (SAM9X60). This behavior has been encountered previously
while debugging this code and using the same mechanism for pre-loading
address for different controllers (e.g. pin controller, the assumption
being that other requested translations are replaced from TLB).
To solve this new issue the TLB flush + the extension of pre-loading
the rest of controllers to TLB (e.g. PMC, RAMC) has been added. The
rest of the controllers should have been pre-loaded previously, anyway.
Fixes: f0bbf17958 ("ARM: at91: pm: add self-refresh support for sama7g5")
Depends-on: e42cbbe5c9 ("ARM: at91: pm: group constants and addresses loading")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210930154219.2214051-4-claudiu.beznea@microchip.com
Backup area is now switched to VDDIN33 at boot (with the help of
bootloader). When switching to backup mode we need to switch backup area
to VBAT as all the other power sources are cut off. The resuming from
backup mode is done with the help of bootloader, so there is no need to
do something particular in Linux to restore backup area power source.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210830100927.22711-1-claudiu.beznea@microchip.com
In case PM is enabled but there is no RAM controller information
in DT the code will panic. Avoid such scenarios by not initializing
platform specific PM code in case RAM controller is not provided
via DT.
Reported-by: Eugen Hristev <eugen.hristev@microchip.com>
Fixes: 827de1f123 ("ARM: at91: remove at91_dt_initialize and machine init_early()")
Fixes: 892e1f4a3a ("ARM: at91: pm: add sama7g5 ddr phy controller")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210823131915.23857-2-claudiu.beznea@microchip.com
Introduce new family of SoCs, sama7, and first SoC, sama7g5.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[claudiu.beznea@microchip.com: keep only the sama7_dt]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-23-claudiu.beznea@microchip.com
Adapt at91_pm_backup_init() to work for SAMA7G5. Also, set the LPM pin
to shutdown controller. This will signal to PMIC that it needs to switch
to the state corresponding to backup mode.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-21-claudiu.beznea@microchip.com
The resuming from backup mode is done with the help of bootloader.
The bootloader reconfigure the DDR controller and DDR PHY controller.
To speed-up the resuming process save the PHY calibration data into
SECURAM before suspending (securam is powered on backup mode).
This data will be later used by bootloader in DDR PHY reconfiguration
process. Also, in the process or recalibration the first 8 words of
the memory may get corrupted. To solve this, these 8 words are saved
in the securam and restored by bootloader in the process of PHY
configuration.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-20-claudiu.beznea@microchip.com
SAMA7G5 self-refresh procedure accesses also the DDR PHY registers.
Adapt the code so that the at91_dt_ramc() to look also for DDR PHYs,
in case it is mandatory.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-19-claudiu.beznea@microchip.com
Add SAMA7G5 DDR controller to the list of DDR controller compatibles.
At the moment there is no standby support. Adapt the code for this.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-18-claudiu.beznea@microchip.com
SAMA7G5 has 5 master clocks 0..4. MCK0 is controlled differently than
MCK 1..4. MCK 1..4 should also be saved/restored in the last phase of
suspend/resume. Thus, adapt wait_mckrdy to support also MCK1..4.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-10-claudiu.beznea@microchip.com
Replace CONFIG_SOC_SAM9X60 with CONFIG_HAVE_AT91_SAM9X60_PLL as the
SAM9X60's PLL is also present on SAMA7G5.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-9-claudiu.beznea@microchip.com
For the previous AT91 RAM controller and self-refresh procedure this
had no side effects. However, for SAMA7G5 the self-refresh procedure
doesn't allow this anymore as the RAM controller ports are closed
before switching it to self-refresh. This commits prepares the code
for the following ones adding self-refresh and PM support for SAMA7G5.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-8-claudiu.beznea@microchip.com
at91_pm_modes_init() checks for proper nodes in device tree and maps
them accordingly. Up to SAMA7G5 all AT91 SoCs had the same mapping
b/w power saving modes and different controllers needed in the
final/first steps of suspend/resume. SAMA7G5 is not aligned with the
old SoCs thus the code is adapted for this. This patch prepares
the field for next commits.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-5-claudiu.beznea@microchip.com
Move the setup of soc_pm.bu->suspended in platform_suspend::begin
function so that the PMC code in charge with clocks suspend/resume
to differentiate b/w standard PM mode and backup mode.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-3-claudiu.beznea@microchip.com
Both the caller and the supplier's source file should have access to
the include file containing the prototypes.
Fixes the following W=1 kernel build warning(s):
drivers/pinctrl/pinctrl-at91.c:1637:6: warning: no previous prototype for ‘at91_pinctrl_gpio_suspend’ [-Wmissing-prototypes]
1637 | void at91_pinctrl_gpio_suspend(void)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/pinctrl/pinctrl-at91.c:1661:6: warning: no previous prototype for ‘at91_pinctrl_gpio_resume’ [-Wmissing-prototypes]
1661 | void at91_pinctrl_gpio_resume(void)
| ^~~~~~~~~~~~~~~~~~~~~~~~
Cc: Russell King <linux@armlinux.org.uk>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210303124149.3149511-1-lee.jones@linaro.org
Compiling with the clang integrated assembler warns about
a recently added instruction:
<instantiation>:14:13: error: unknown token in expression
ldr tmp1, =#0x00020010UL
arch/arm/mach-at91/pm_suspend.S:542:2: note: while in macro instantiation
at91_plla_enable
Remove the extra '#' character that is not used for the 'ldr'
instruction when doing an indirect load of a constant.
Fixes: 4fd36e4583 ("ARM: at91: pm: add plla disable/enable support for sam9x60")
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210204160129.2249394-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Not all SoCs supports all the PM mode. User may end up settings,
e.g. backup mode, on a non SAMA5D2 device, but the mode to not be valid.
If backup mode is used on a devices not supporting it there will be no
way of resuming other than rebooting.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1596616610-15460-3-git-send-email-claudiu.beznea@microchip.com
ULP0 fast improves suspend/resume time with few milliseconds the drawback
being the power consumption. The mean values measured for suspend/resume
time are as follows (measured on SAMA5D2 Xplained board), ULP0 compared
with fast ULP0:
- ulp0 fast: suspend time: 169 ms, resume time: 216 ms
- ulp0 : suspend time: 197 ms, resume time: 258 ms
Current consumption while suspended (measured on SAMA5D2 Xplained board):
- ulp0 fast: 730uA
- ulp0 : 270uA
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1596616610-15460-2-git-send-email-claudiu.beznea@microchip.com
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200713065859.31770-1-grandmaster@al2klimov.de
if of_find_device_by_node() succeed, at91_pm_sram_init() doesn't have
a corresponding put_device(). Thus add a jump target to fix the exception
handling for this function implementation.
Fixes: d2e4679055 ("ARM: at91: pm: use the mmio-sram pool to access SRAM")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200604123301.3905837-1-yukuai3@huawei.com
The code changes are mostly for 32-bit platforms and include:
- Lots of updates for the Nvidia Tegra platform, including
cpuidle, pmc, and dt-binding changes
- Microchip at91 power management updates for the recently added
sam9x60 SoC
- Treewide setup_irq deprecation by afzal mohammed
- STMicroelectronics stm32 gains earlycon support
- Renesas platforms with Cortex-A9 can now use the global timer
- Some TI OMAP2+ platforms gain cpuidle support
- Various cleanups for the i.MX6 and Orion platforms, as well as
Kconfig files across all platforms
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=UTk1
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"The code changes are mostly for 32-bit platforms and include:
- Lots of updates for the Nvidia Tegra platform, including cpuidle,
pmc, and dt-binding changes
- Microchip at91 power management updates for the recently added
sam9x60 SoC
- Treewide setup_irq deprecation by afzal mohammed
- STMicroelectronics stm32 gains earlycon support
- Renesas platforms with Cortex-A9 can now use the global timer
- Some TI OMAP2+ platforms gain cpuidle support
- Various cleanups for the i.MX6 and Orion platforms, as well as
Kconfig files across all platforms"
* tag 'arm-soc-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (75 commits)
ARM: qcom: Add support for IPQ40xx
ARM: mmp: replace setup_irq() by request_irq()
ARM: cns3xxx: replace setup_irq() by request_irq()
ARM: spear: replace setup_irq() by request_irq()
ARM: ep93xx: Replace setup_irq() by request_irq()
ARM: iop32x: replace setup_irq() by request_irq()
arm: mach-dove: Mark dove_io_desc as __maybe_unused
ARM: orion: replace setup_irq() by request_irq()
ARM: debug: stm32: add UART early console support for STM32MP1
ARM: debug: stm32: add UART early console support for STM32H7
ARM: debug: stm32: add UART early console configuration for STM32F7
ARM: debug: stm32: add UART early console configuration for STM32F4
cpuidle: tegra: Disable CC6 state if LP2 unavailable
cpuidle: tegra: Squash Tegra114 driver into the common driver
cpuidle: tegra: Squash Tegra30 driver into the common driver
cpuidle: Refactor and move out NVIDIA Tegra20 driver into drivers/cpuidle
ARM: tegra: cpuidle: Remove unnecessary memory barrier
ARM: tegra: cpuidle: Make abort_flag atomic
ARM: tegra: cpuidle: Handle case where secondary CPU hangs on entering LP2
ARM: tegra: Make outer_disable() open-coded
...
