asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Currently DFS works under assumption there could be only one channel
context in the hardware. Hence, drivers just calls the function
ieee80211_radar_detected() passing the hardware structure. However, with
MLO, this obviously will not work since number of channel contexts will be
more than one and hence drivers would need to pass the channel information
as well on which the radar is detected.
Also, when radar is detected in one of the links, other link's CAC should
not be cancelled.
Hence, in order to support DFS with MLO, do the following changes -
* Add channel context conf pointer as an argument to the function
ieee80211_radar_detected(). During MLO, drivers would have to pass on
which channel context conf radar is detected. Otherwise, drivers could
just pass NULL.
* ieee80211_radar_detected() will iterate over all channel contexts
present and
* if channel context conf is passed, only mark that as radar
detected
* if NULL is passed, then mark all channel contexts as radar
detected
* Then as usual, schedule the radar detected work.
* In the worker, go over all the contexts again and for all such context
which is marked with radar detected, cancel the ongoing CAC by calling
ieee80211_dfs_cac_cancel() and then notify cfg80211 via
cfg80211_radar_event().
* To cancel the CAC, pass the channel context as well where radar is
detected to ieee80211_dfs_cac_cancel(). This ensures that CAC is
canceled only on the links using the provided context, leaving other
links unaffected.
This would also help in scenarios where there is split phy 5 GHz radio,
which is capable of DFS channels in both lower and upper band. In this
case, simultaneous radars can be detected.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20240906064426.2101315-9-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers need to purge TX SKB when stopping. Using skb_queue_purge() can't
report TX status to mac80211, causing ieee80211_free_ack_frame() warns
"Have pending ack frames!". Export ieee80211_purge_tx_queue() for drivers
to not have to reimplement it.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240822014255.10211-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may at times want to iterate their stations with a function
which requires some non-atomic operations.
ieee80211_iterate_stations_mtx() introduces an API to iterate stations
while holding that wiphy's mutex. This allows the iterating function to
do non-atomic operations safely.
Signed-off-by: Rory Little <rory@candelatech.com>
Link: https://patch.msgid.link/20240806004024.2014080-2-rory@candelatech.com
[unify internal list iteration functions]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce 'ieee80211_mgmt_ba()' to avoid code duplication between
'ieee80211_send_addba_resp()', 'ieee80211_send_addba_request()',
and 'ieee80211_send_delba()', ensure that all related addresses
are '__aligned(2)', and prefer convenient 'ether_addr_copy()'
over generic 'memcpy()'. No functional changes expected.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Link: https://patch.msgid.link/20240725090925.6022-1-dmantipov@yandex.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most likely the last "new features" pull request for v6.11 with
changes both in stack and in drivers. The big thing is the multiple
radios for wiphy feature which makes it possible to better advertise
radio capabilities to user space. mt76 enabled MLO and iwlwifi
re-enabled MLO, ath12k and rtw89 Wi-Fi 6 devices got WoWLAN support.
Major changes:
cfg80211/mac80211
* remove DEAUTH_NEED_MGD_TX_PREP flag
* multiple radios per wiphy support
mac80211_hwsim
* multi-radio wiphy support
ath12k
* DebugFS support for datapath statistics
* WCN7850: support for WoW (Wake on WLAN)
* WCN7850: device-tree bindings
ath11k
* QCA6390: device-tree bindings
iwlwifi
* mvm: re-enable Multi-Link Operation (MLO)
* aggregation (A-MSDU) optimisations
rtw89
* preparation for RTL8852BE-VT support
* WoWLAN support for WiFi 6 chips
* 36-bit PCI DMA support
mt76
* mt7925 Multi-Link Operation (MLO) support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmaPsBQRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt9EQf/Wevf/RnKyHhcuW4kmv0cxnjLW39K7CAh
ZlfN2JNTsVk4Na1EBjUgVyAWGdnGQpEhQlJYDExHcf5iD12pMVMIAQS8JXTDxuva
+ErAN1652p2N8nFCkNNuGbjYfO0D61xSIQj2uHhAlafK2k8FwnSn6XPP6jjHWvur
Acmw6W6l8eL+MP2K1VN2/2S09Gr6IQs7gXgWQX/6CaoK+OynFbUg8T9GQ2aqjr+d
lD17YB+oOHNCBxvg9LtBhKdfV14OBkKT6hW+YEqsrBEbx3N07ogDkPO0NUUPMXN3
IePEhj4XXrJ5UBMTvgWzNG9CwPeZFwuKGga+HZO9RKF5rwu42LsUMA==
=MpwE
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.11
Most likely the last "new features" pull request for v6.11 with
changes both in stack and in drivers. The big thing is the multiple
radios for wiphy feature which makes it possible to better advertise
radio capabilities to user space. mt76 enabled MLO and iwlwifi
re-enabled MLO, ath12k and rtw89 Wi-Fi 6 devices got WoWLAN support.
Major changes:
cfg80211/mac80211
* remove DEAUTH_NEED_MGD_TX_PREP flag
* multiple radios per wiphy support
mac80211_hwsim
* multi-radio wiphy support
ath12k
* DebugFS support for datapath statistics
* WCN7850: support for WoW (Wake on WLAN)
* WCN7850: device-tree bindings
ath11k
* QCA6390: device-tree bindings
iwlwifi
* mvm: re-enable Multi-Link Operation (MLO)
* aggregation (A-MSDU) optimisations
rtw89
* preparation for RTL8852BE-VT support
* WoWLAN support for WiFi 6 chips
* 36-bit PCI DMA support
mt76
* mt7925 Multi-Link Operation (MLO) support
* tag 'wireless-next-2024-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (204 commits)
wifi: mac80211: fix AP chandef capturing in CSA
wifi: iwlwifi: correctly reference TSO page information
wifi: mt76: mt792x: fix scheduler interference in drv own process
wifi: mt76: mt7925: enabling MLO when the firmware supports it
wifi: mt76: mt7925: remove the unused mt7925_mcu_set_chan_info
wifi: mt76: mt7925: update mt7925_mac_link_bss_add for MLO
wifi: mt76: mt7925: update mt7925_mcu_bss_basic_tlv for MLO
wifi: mt76: mt7925: update mt7925_mcu_set_timing for MLO
wifi: mt76: mt7925: update mt7925_mcu_sta_phy_tlv for MLO
wifi: mt76: mt7925: update mt7925_mcu_sta_rate_ctrl_tlv for MLO
wifi: mt76: mt7925: add mt7925_mcu_sta_eht_mld_tlv for MLO
wifi: mt76: mt7925: update mt7925_mcu_sta_update for MLO
wifi: mt76: mt7925: update mt7925_mcu_add_bss_info for MLO
wifi: mt76: mt7925: update mt7925_mcu_bss_mld_tlv for MLO
wifi: mt76: mt7925: update mt7925_mcu_sta_mld_tlv for MLO
wifi: mt76: mt7925: add mt7925_[assign,unassign]_vif_chanctx
wifi: mt76: add def_wcid to struct mt76_wcid
wifi: mt76: mt7925: report link information in rx status
wifi: mt76: mt7925: update rate index according to link id
wifi: mt76: mt7925: add link handling in the mt7925_ipv6_addr_change
...
====================
Link: https://patch.msgid.link/20240711102353.0C849C116B1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the definition of BSS_CHANGED_UNSOL_BCAST_PROBE_RESP so that
not all higher bits get set, 1<<31 is a signed variable, so when
we do
u64 changed = BSS_CHANGED_UNSOL_BCAST_PROBE_RESP;
we get sign expansion, so the value is 0xffff'ffff'8000'0000 and
that's clearly not desired. Use BIT_ULL() to make it unsigned as
well as the right type for the change flags.
Fixes: 178e9d6adc ("wifi: mac80211: fix unsolicited broadcast probe config")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240627104257.06174d291db2.Iba0d642916eb78a61f8ab2cc5ca9280783d9c1db@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This flag is annoying because it puts a lot of logic into mac80211
that could just as well be in the driver (only iwlmvm uses it) and
the implementation is also broken for MLO.
Remove the flag in favour of calling drv_mgd_prepare_tx() without
any conditions even for the deauth-while-assoc case. The drivers
that implement it can take the appropriate actions, which for the
only user of DEAUTH_NEED_MGD_TX_PREP (iwlmvm) is a bit more tricky
than the implementation in mac80211 is anyway, and all others have
no need and can just exit if info->was_assoc is set.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240627132527.94924bcc9c9e.I328a219e45f2e2724cd52e75bb9feee3bf21a463@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add flag for Full Bandwidth UL MU-MIMO for EHT. This is utilized
to pass EHT MU-MIMO configurations from user space to driver
in AP mode.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Link: https://msgid.link/20240515181327.12855-2-quic_pradeepc@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of passing the full TPE elements, in all their glory
and mixed up data formats for HE backward compatibility, parse
them fully into the right values, and pass that to the drivers.
Also introduce proper validation already in mac80211, so that
drivers don't need to do it, and parse the EHT portions.
The code now passes the values in the right order according to
the channel used by an interface, which could also be a subset
of the data advertised by the AP, if we couldn't connect with
the full bandwidth (for whatever reason.)
Also add kunit tests for the more complicated bits of it.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240506214536.2aa839969b60.I265b28209e0b29772b2f125f7f83de44a4da877b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend the flag IEEE80211_KEY_FLAG_GENERATE_MMIE to BIP-CMAC-256,
BIP-GMAC-128 and BIP-GMAC-256 for the same reason and in the same
way that the flag was added originally in commit a0b4496a43
("mac80211: add IEEE80211_KEY_FLAG_GENERATE_MMIE to ieee80211_key_flags").
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Link: https://msgid.link/20240326003036.15215-1-michael-cy.lee@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
kernel-doc is reporting some warnings, so fix them:
% scripts/kernel-doc -Wall -Werror -none include/net/mac80211.h
include/net/mac80211.h:2056: warning: No description found for return value of 'wdev_to_ieee80211_vif'
include/net/mac80211.h:2066: warning: No description found for return value of 'ieee80211_vif_to_wdev'
include/net/mac80211.h:5603: warning: No description found for return value of 'ieee80211_beacon_cntdwn_is_complete'
include/net/mac80211.h:5968: warning: No description found for return value of 'ieee80211_gtk_rekey_add'
include/net/mac80211.h:6350: warning: No description found for return value of 'ieee80211_find_sta_by_link_addrs'
include/net/mac80211.h:6478: warning: No description found for return value of 'ieee80211_txq_airtime_check'
include/net/mac80211.h:6981: warning: No description found for return value of 'rate_control_set_rates'
include/net/mac80211.h:7142: warning: No description found for return value of 'ieee80211_tx_prepare_skb'
include/net/mac80211.h:7156: warning: No description found for return value of 'ieee80211_parse_tx_radiotap'
include/net/mac80211.h:7277: warning: No description found for return value of 'ieee80211_tx_dequeue'
include/net/mac80211.h:7292: warning: No description found for return value of 'ieee80211_tx_dequeue_ni'
include/net/mac80211.h:7324: warning: No description found for return value of 'ieee80211_next_txq'
include/net/mac80211.h:7405: warning: No description found for return value of 'ieee80211_txq_may_transmit'
include/net/mac80211.h:7466: warning: No description found for return value of 'ieee80211_calc_rx_airtime'
include/net/mac80211.h:7480: warning: No description found for return value of 'ieee80211_calc_tx_airtime'
include/net/mac80211.h:7528: warning: No description found for return value of 'ieee80211_is_tx_data'
include/net/mac80211.h:7562: warning: No description found for return value of 'ieee80211_set_active_links'
17 warnings as Errors
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://msgid.link/20240329-mac80211-kdoc-retval-v1-2-5e4d1ad6c250@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While fixing kernel-doc issues it was discovered that the
ieee80211_set_hw_80211_encap() prototype doesn't actually have an
implementation, so remove it.
Note the implementation was removed in commit 6aea26ce5a ("mac80211:
rework tx encapsulation offload API").
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://msgid.link/20240329-mac80211-kdoc-retval-v1-1-5e4d1ad6c250@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to activate a link that is currently inactive due to
a negotiated TTLM request, need to first tear down the negotiated
TTLM request.
Add support for sending TTLM teardown request and update the links
state accordingly.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.d480cbf46fcf.Idedad472469d2c27dd2a088cf80a13a1e1cf9b78@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices may not be capable of handling puncturing in 5 GHz
only (vs. the current flag that just removes puncturing support
completely). Add a flag to support such devices: check and then
downgrade the channel width if needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.49759510da7d.I12c5a61f0be512e0c4e574c2f794ef4b37ecaf6b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
BSS_CHANGED_MLD_TTLM purpose is to let the driver know that
negotiated TTLM was updated and as a result MLD suspended links
status was change.
Fix the description to better reflect it.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.52b893a70758.I2dcb322b389441f33605fb952450cc2724eb9efd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since I keep getting confused about this and asking about it,
update the documentation.
In the future, especially when we add more reasons for a link
to be disabled, we should add a per-link 'disable state' bitmap
instead of maintaining all these bitmaps with subset logic, to
indicate each of the different states separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.a5b24595b1a2.I92dd7d177b25df189b842d3bcddb1f2b13b1de13@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When doing CSA in multi-link, there really isn't a need to
stop transmissions entirely. Add a feature flag for drivers
to indicate they can handle quiet in CSA (be it by parsing
themselves, or by implementing drv_pre_channel_switch()),
to make that possible.
Also clean up the csa_block_tx handling: it clearly cannot
handle multi-link due to the way queues are stopped, move
it to the sdata. Drivers should be doing it themselves for
working properly during CSA in MLO anyway. Also rename it
to indicate that it reflects TX was blocked at mac80211.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228095719.258439191541.I2469d206e2bf5cb244cfde2b4bbc2ae6d1cd3dd9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the link conf to the abort_channel_switch driver
method so the driver can handle things correctly.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228095718.27f621106ddd.Iadd3d69b722ffe5934779a32a0e4e596a4e33ed4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For CSA to work correctly in multi-link scenarios, pass
the link_id to the relevant callbacks.
While at it, unify/deduplicate the tracing for them.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://msgid.link/20240228095718.b7726635c054.I0be5d00af4acb48cfbd23a9dbf067f9aeb66469d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We sometimes need to check if a link is active, and this
is complicated by the fact that active_links has no bits
set when the vif isn't (acting as) an MLD. Add a small
new helper ieee80211_vif_link_active() to make that a bit
easier, and use it in a few places.
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094901.688760aff5f7.I06892a503f5ecb9563fbd678d35d08daf7a044b0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In MLO, we need the link id in the GTK key to be given by
the driver after rekeying in wowlan, so add that.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094500.ce1bfc83a680.I43a6f8ab2804ee07116a37d5b9ec601b843464b1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, function to check if beacon countdown is complete uses deflink
to fetch the beacon and check the counter. However, with MLO, there is
a need to check the counter for the beacon in a particular link.
Add support to use link_id in order to fetch the beacon from a particular
link data.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240216144621.514385-2-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Get rid of gfp parameter from ieee80211_obss_color_collision_notify
since it is no longer used.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/f91e1c78896408ac556586ba8c99e4e389aeba02.1707389901.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently ieee80211_csa_finish() function finalizes CSA by scheduling a
finalizing worker using the deflink. With MLO, there is a need to do it
on a given link basis.
Pass link ID of the link on which CSA needs to be finalized.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240130140918.1172387-6-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, function to update beacon counter uses deflink to fetch
the beacon and then update the counter. However, with MLO, there is
a need to update the counter for the beacon in a particular link.
Add support to use link_id in order to fetch the beacon from a particular
link data during beacon update counter.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240130140918.1172387-3-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Aloka originally suggested that puncturing should be part of
the chandef, so that it's treated correctly. At the time, I
disagreed and it ended up not part of the chandef, but I've
now realized that this was wrong. Even for clients, the RX,
and perhaps more importantly, CCA configuration needs to take
puncturing into account.
Move puncturing into the chandef, and adjust all the code
accordingly. Also add a few tests for puncturing in chandef
compatibility checking.
Link: https://lore.kernel.org/linux-wireless/20220214223051.3610-1-quic_alokad@quicinc.com/
Suggested-by: Aloka Dixit <quic_alokad@quicinc.com>
Link: https://msgid.link/20240129194108.307183a5d2e5.I4d7fe2f126b2366c1312010e2900dfb2abffa0f6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
EHT requires that stations are able to participate in
wider bandwidth OFDMA, i.e. parse downlink OFDMA and
uplink OFDMA triggers when they're not capable of (or
not connected at) the (wider) bandwidth that the AP
is using. This requires hardware configuration, since
the entity responsible for parsing (possibly hardware)
needs to know the AP bandwidth.
To support this, change the channel request to have
the AP's bandwidth for clients, and track that in the
channel context in mac80211. This means that the same
chandef might need to be split up into two different
contexts, if the APs are different. Interfaces other
than client are not participating in OFDMA the same
way, so they don't request any AP setting.
Note that this doesn't introduce any API to split a
channel context, so that there are cases where this
might lead to a disconnect, e.g. if there are two
client interfaces using the same channel context, e.g.
both 160 MHz connected to different 320 MHz APs, and
one of the APs switches to 160 MHz.
Note also there are possible cases where this can be
optimised, e.g. when using the upper or lower 160 Mhz,
but I haven't been able to really fully understand the
spec and/or hardware limitations.
If, for some reason, there are no hardware limits on
this because the OFDMA (downlink/trigger) parsing is
done in firmware and can take the transmitter into
account, then drivers can set the new flag
IEEE80211_VIF_IGNORE_OFDMA_WIDER_BW on interfaces to
not have them request any AP bandwidth in the channel
context and ignore this issue entirely. The bss_conf
still contains the AP configuration (if any, i.e. EHT)
in the chanreq.
Link: https://msgid.link/20240129194108.d3d5b35dd783.I939d04674f4ff06f39934b1591c8d36a30ce74c2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For channel contexts, mac80211 currently uses the cfg80211
chandef struct (control channel, center freq(s), width) to
define towards drivers and internally how these behave. In
fact, there are _two_ such structs used, where the min_def
can reduce bandwidth according to the stations connected.
Unfortunately, with EHT this is longer be sufficient, at
least not for all hardware. EHT requires that non-AP STAs
that are connected to an AP with a lower bandwidth than it
(the AP) advertises (e.g. 160 MHz STA connected to 320 MHz
AP) still be able to receive downlink OFDMA and respond to
trigger frames for uplink OFDMA that specify the position
and bandwidth for the non-AP STA relative to the channel
the AP is using. Therefore, they need to be aware of this,
and at least for some hardware (e.g. Intel) this awareness
is in the hardware. As a result, use of the "same" channel
may need to be split over two channel contexts where they
differ by the AP being used.
As a first step, introduce a concept of a channel request
('chanreq') for each interface, to control the context it
requests. This step does nothing but reorganise the code,
so that later the AP's chandef can be added to the request
in order to handle the EHT case described above.
Link: https://msgid.link/20240129194108.2e88e48bd2e9.I4256183debe975c5ed71621611206fdbb69ba330@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are still surprisingly many non-chanctx drivers, but in
mac80211 that code is a bit awkward. Simplify this by having
those drivers assign 'emulated' ops, so that the mac80211 code
can be more unified between non-chanctx/chanctx drivers. This
cuts the number of places caring about it by about 15, which
are scattered across - now they're fewer and no longer in the
channel context handling.
Link: https://msgid.link/20240129194108.6d0ead50f5cf.I60d093b2fc81ca1853925a4d0ac3a2337d5baa5b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If software crypto is used, simply add support for SPP A-MSDUs
(and use it whenever enabled as required by the cfg80211 API).
If hardware crypto is used, leave it up to the driver to set
the NL80211_EXT_FEATURE_SPP_AMSDU_SUPPORT flag and then check
sta->spp_amsdu or the IEEE80211_KEY_FLAG_SPP_AMSDU key flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.b8ada4514e2b.I1ac25d5f158165b5a88062a5a5e4c4fbeecf9a5d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update neg_ttlm and active_links according to the new mapping,
and send a negotiated TID-to-link map request with the new mapping.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.eeb385d771df.I2a5441c14421de884dbd93d1624ce7bb2c944833@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An MLD may send TID-to-Link mapping request frame to negotiate
TID to link mapping with a peer MLD.
Support handling negotiated TID-to-Link mapping request frame
by parsing the frame, asking the driver whether it supports the
received mapping or not, and sending a TID-to-Link mapping response
to the AP MLD.
Theoretically, links that became inactive due to the received TID-to-Link
mapping request, can be selected to be activated but this would require
tearing down the negotiated TID-to-Link mapping, which is still not
supported.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.0bc1a24fcc9d.Ie72e47dc6f8c77d4a2f0947b775ef6367fe0edac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During ieee80211_set_active_links() we do (among the others):
1. Call drv_change_vif_links() with both old_active and new_active
2. Unassign the chanctx for the removed link(s) (if any)
3. Assign chanctx to the added link(s) (if any)
4. Call drv_change_vif_links() with the new_active links bitmap
The problem here is that during step #1 the driver doesn't know whether
we will activate multiple links simultaneously or are just doing a link
switch, so it can't check there if multiple links are supported/enabled.
(Some of the drivers might enable/disable this option dynamically)
And during step #3, in which the driver already knows that,
returning an error code (for example when multiple links are not
supported or disabled), will cause a warning, and we will still complete
the transition to the new_active links.
(It is hard to undo things in that stage, since we released channels etc.)
Therefore add a driver callback to check if the desired new_active links
will be supported by the driver or not. This callback will be called
in the beginning of ieee80211_set_active_links() so we won't do anything
before we are sure it is supported.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20231220133549.64c4d70b33b8.I79708619be76b8ecd4ef3975205b8f903e24a2cd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When reporting the radiotap timestamp, the mactime field is
usually unused, we take the data from the device_timestamp.
However, there can be cases where the radiotap timestamp is
better reported as a 64-bit value, so since the mactime is
free, add a flag to support using the mactime as a 64-bit
radiotap timestamp.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.00c8b9234f0c.Ie3ce5eae33cce88fa01178e7aea94661ded1ac24@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We only have a single flag free, and before using that for
another mactime flag, instead refactor the mactime flags
to use a 2-bit field.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.d0e664832d14.I20c8900106f9bf81316bed778b1e3ce145785274@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
include/net/mac80111.h contains a number of either excess or incorrect
kerneldoc entries for structure members, leading to these warnings:
./include/net/mac80211.h:491: warning: Excess struct member 'rssi' description in 'ieee80211_event'
./include/net/mac80211.h:491: warning: Excess struct member 'mlme' description in 'ieee80211_event'
./include/net/mac80211.h:491: warning: Excess struct member 'ba' description in 'ieee80211_event'
./include/net/mac80211.h:777: warning: Excess struct member 'ack_enabled' description in 'ieee80211_bss_conf'
./include/net/mac80211.h:1222: warning: Excess struct member 'ampdu_ack_len' description in 'ieee80211_tx_info'
./include/net/mac80211.h:1222: warning: Excess struct member 'ampdu_len' description in 'ieee80211_tx_info'
./include/net/mac80211.h:1222: warning: Excess struct member 'ack_signal' description in 'ieee80211_tx_info'
./include/net/mac80211.h:2920: warning: Excess struct member 'radiotap_he' description in 'ieee80211_hw'
Fix or remove the entries as needed. This change removes 208 warnings from
a "make htmldocs" build.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://msgid.link/87zfy4bhxo.fsf@meer.lwn.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There may be cases where puncturing isn't possible, and
a connection needs to be downgraded. Add a hardware flag
to support this.
This is likely temporary: it seems we will need to move
puncturing to the chandef/channel context.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231211085121.c1e89ea55e93.I37b8ca0ee64d5d7699e351785a9010afc106da3c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the locking rework, more functions need to be called
with the wiphy mutex held. Document that, and for that use
the "Context" description that shows up more nicely in the
generated documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231211085121.24fa44c7eeb4.I8c9e030ddd78e07c99dd21fe1d5156555390f92e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
make htmldocs warns:
Documentation/driver-api/80211/mac80211:109: ./include/net/mac80211.h:5170: WARNING: Duplicate C declaration, also defined at mac80211:1117.
Declaration is '.. c:function:: void ieee80211_tx_status (struct ieee80211_hw *hw, struct sk_buff *skb)'.
This is because there's a function named ieee80211_tx_status() and a struct named
ieee80211_tx_status. This has been discussed previously but no solution found:
https://lore.kernel.org/all/20220521114629.6ee9fc06@coco.lan/
There's also a bug open for three years with no solution in sight:
https://github.com/sphinx-doc/sphinx/pull/8313
So I guess we have no other solution than to a workaround this in the code,
for example to rename the function to ieee80211_tx_status_skb() to avoid the
name conflict. I got the idea for the name from ieee80211_tx_status_noskb() in
which the skb is not provided as an argument, instead with
ieee80211_tx_status_skb() the skb is provided.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231012114229.2931808-2-kvalo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Correct typos and fix run-on sentences.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231001191633.19090-2-rdunlap@infradead.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
