When DPM for the specific clock is disabled, driver should still print out
current clock info for rocm-smi support on vega20
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Eric Huang <JinhuiEric.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently there is a small race window where we could manage to arm the
vblank event from atomic flush, but programming the hardware was too close
to the frame end, so the hardware will only apply the current state on the
next vblank. In this case we will send out the commit done event too early
causing userspace to reuse framebuffes that are still in use.
Instead of using the event arming mechnism, just remember the pending event
and send it from the vblank IRQ handler, once we are sure that all state
has been applied successfully.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[p.zabel@pengutronix.de: inverted logic: done -> pending, added back
spinlock in atomic_flush, commit message typo fix]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Allow to compile-test imx-drm on other platforms.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Since the TVE provides a clock to the DI, the driver can only be
compiled if the common clock framework is enabled. With the COMMON_CLK
dependency in place, it will be possible to allow building the other
parts of imx-drm under COMPILE_TEST on architectures that do not select
the common clock framework.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add a zpos property to planes. Call drm_atomic_helper_check() instead of
calling drm_atomic_helper_check_modeset() and drm_atomic_check_planes()
manually. This effectively adds a call to drm_atomic_normalize_zpos()
before checking planes. Reorder atomic update to allow changing plane
zpos without modeset.
Note that the initial zpos is set in ipu_plane_state_reset(). The
initial value set in ipu_plane_init() is just for show. The zpos
parameter of drm_plane_create_zpos_property() is ignored because
the newly created plane do not have state yet.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Marius Vlad <marius.vlad@collabora.com>
This function allows upper layer to check if a requested atomic update
to the plane has been applied or is still pending.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[p.zabel@pengutronix.de: inverted logic: done -> pending]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This allows channels using the PRG to check if a requested configuration
update has been applied or is still pending.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[p.zabel@pengutronix.de: inverted logic: done -> pending]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This allows the upper layers to check if a double buffer update has
been applied by the PRE or is still pending.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[p.zabel@pengutronix.de: inverted logic: done -> pending]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Depends on GEN family and I915_PARAM_HAS_CONTEXT_ISOLATION, Mesa driver
will decide whether constant buffer 0 address is relative or absolute,
and load GPU initial state by lri to context mmio INSTPM (GEN8)
or 0x20D8 (>=GEN9).
Mesa Commit fa8a764b62
("i965: Use absolute addressing for constant buffer 0 on Kernel 4.16+.")
INSTPM is already added to gen8_engine_mmio_list, but 0x20D8 is missed
in gen9_engine_mmio_list. From GVT point of view, different guest could
have different context so should switch those mmio accordingly.
v2: Update fixes commit ID.
Fixes: 1786571393 ("drm/i915/gvt: vGPU context switch")
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Fixes for 5.1:
amdgpu:
- Fix missing fw declaration after dropping old CI DPM code
- Fix debugfs access to registers beyond the MMIO bar size
- Fix context priority handling
- Add missing license on some new files
- Various cleanups and bug fixes
radeon:
- Fix missing break in CS parser for evergreen
- Various cleanups and bug fixes
sched:
- Fix entities with 0 run queues
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190221214134.3308-1-alexander.deucher@amd.com
A bit bigger than normal for this week due to fixes for some long
standing display issues that are bound for stable. These changes would
be going to stable anyway, so I figured it was better via 5.0 than 5.1.
- Several display fixes
- Fix PX systems due to core changes in runtime pm
- Disable bulk moves. They are fixed in 5.1, but fix is too invasive for 5.0
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190220225715.3240-1-alexander.deucher@amd.com
When running RISC-V QEMU with the Bochs device attached via PCIe the
probe of the Bochs device fails with:
[drm:bochs_hw_init] *ERROR* ID mismatch
This was introduced by this commit:
7780eb9ce8 bochs: convert to drm_dev_register
To fix the error we ensure that pci_enable_device() is called before
bochs_load().
Fixes: 7780eb9ce8 ("bochs: convert to drm_dev_register")
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reported-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190221003231.31625-1-alistair.francis@wdc.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When MI_FLUSH_DW post write hw status page in index mode, the index
value is in dword step and turned into address offset in cmd dword1.
As status page size is 4K, so can't exceed that.
This fixed upper bound check in cmd parser code which incorrectly
stopped VM for reason of invalid MI_FLUSH_DW write index.
v2:
- Fix upper bound as 4K page size because index value is address offset.
Fixes: be1da7070a ("drm/i915/gvt: vGPU command scanner")
Cc: stable@vger.kernel.org # v4.10+
Cc: "Zhao, Yan Y" <yan.y.zhao@intel.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
The changes to fix those are two invasive for backporting.
Just disable the feature in 4.20 and 5.0.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: <stable@vger.kernel.org> [4.20+]
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When a dce80 asic was suspended, the clocks were not set to 0.
Upon resume, the new clock was compared to the existing clock,
they were found to be the same, and so the clock was not set.
This resulted in a blackscreen.
[How]
In atomic commit, check to see if there are any active pipes.
If no, set clocks to 0
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
optimize_bandwidth was using dce100_prepare_bandwidth this is incorrect
[How]
change it to dce100_optimize_bandwidth
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
If the cursor pos passed from DM is less than the plane_state->dst_rect
top left corner then the unsigned cursor pos wraps around to a large
positive number since cursor pos is a u32.
There was an attempt to guard against this in hubp1_cursor_set_position
by checking the src_x_offset and src_y_offset and offseting the
cursor hotspot within hubp1_cursor_set_position.
However, the cursor position itself is still being programmed
incorrectly as a large value.
This manifests itself visually as the cursor disappearing or containing
strange artifacts near the middle of the screen on raven.
[How]
Don't subtract the destination rect top left corner from the pos but
add it to the hotspot instead. This happens before the pos gets
passed into hubp1_cursor_set_position.
This achieves the same result but avoids the subtraction wrap around.
With this fix the original cursor programming logic can be used again.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Murton Liu <Murton.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need 32ea33a044 ("mei: bus: export to_mei_cl_device for mei
client devices drivers") for the mei-hdcp patches.
References: https://lkml.org/lkml/2019/2/19/356
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
If we skipped all the connectors that were not part of a tile, we would
leave conn_seq=0 and conn_configured=0, convincing ourselves that we
had stagnated in our configuration attempts. Avoid this situation by
starting conn_seq=ALL_CONNECTORS, and repeating until we find no more
connectors to configure.
Fixes: 754a76591b ("drm/i915/fbdev: Stop repeating tile configuration on stagnation")
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190215123019.32283-1-chris@chris-wilson.co.uk
Cc: <stable@vger.kernel.org> # v3.19+
(cherry picked from commit d9b308b1f8)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This add an ioctl to migrate a range of process address space to the
device memory. On platform without cache coherent bus (x86, ARM, ...)
this means that CPU can not access that range directly, instead CPU
will fault which will migrate the memory back to system memory.
This is behind a staging flag so that we can evolve the API.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Device memory can be use in SVM, in which case we do not have any of
the existing buffer object. This commit add infrastructure to allow
use of device memory without nouveau_bo. Again this is a temporary
solution until a rework of GPU memory management.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
This uses HMM to mirror a process' CPU page tables into a channel's page
tables, and keep them synchronised so that both the CPU and GPU are able
to access the same memory at the same virtual address.
While this code also supports Volta/Turing, it's only enabled for Pascal
GPUs currently due to channel recovery being unreliable right now on the
later GPUs.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
For a channel to make use of SVM features, it requires a different GPU MMU
configuration than we would normally use, which is not desirable to switch
to unless a client is actively going to use SVM.
In order to supporting SVM without more extensive changes to the userspace
interfaces, the SVM_INIT ioctl needs to replace the previous configuration
safely.
The only way we can currently do this safely, accounting for some unlikely
failure conditions, is to allocate the new VMM without destroying the last
one, and prioritising the SVM-enabled configuration in the code that cares.
This will get cleaned up again further down the track.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Some GPU units are capable of supporting "replayable" page faults, where
the execution unit will wait for SW to fixup GPU page tables rather than
triggering a channel-fatal fault.
This feature isn't useful (it's harmful, even) unless something like HMM
is being used to manage events appearing in the replayable fault buffer,
so, it's disabled by default.
This commit allows a client to request it be enabled.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Host methods exist to do at least some of what we need, but we are not
currently pushing replay/cancels through a channel like UVM does as it's
not clear whether it's necessary in our case (UVM also updates PTEs with
the GPU).
UVM also pushes a software method for fault cancels on Pascal, seemingly
because the host methods don't appear to be sufficient. If/when we want
to push the replay/cancel on the GPU, we can re-purpose the cancellation
code here to implement that swmthd.
Keep it simple for now, until we figure out exactly what we need here.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This provides a somewhat more direct method of manipulating the GPU page
tables, which will be required to support SVM.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This will be used to support a privileged client providing PTEs directly,
without a memory object to use as a reference.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
NVKM is currently responsible for managing the allocation of a client's
GPU address-space, but there's various use-cases (ie. HMM address-space
mirroring) where giving a client more direct control is desirable.
This commit allows for a VMM to be created where the area allocated for
NVKM is limited to a client-specified window, the remainder of address-
space is controlled directly by the client.
Leaving a window is necessary to support various internal requirements,
but also to support existing allocation interfaces as not all of the HW
is capable of working with a HMM allocation.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There are a few statements that are indented incorrectly. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's no need to avoid using copy engines if gr init fails for some
reason (usually missing FW, or incomplete bring-up).
It's not terribly useful for an end-user, but it'll slightly speed up
suspend/resume when saving fb contents, and allow for host/ce code to
be validated.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Some of the pre-NV50 depends on SW methods to implement synchronisation
for page flips, and we want to move this setup out of common code, thus
we require the channel to have been allocation before display init.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
As I currently understand it, this is related to features we have no
support for as of yet.
In theory, this change should be a noop, just without the warning.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Turing has its SEC2 instance in an alternate location, and this avoids
needing to duplicate the code here for it.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Will be using this in upcoming changes to avoid the need for entirely
new subdevs to deal with Turing register moves.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The NOUVEAU_GETPARAM_PCI_DEVICE case is missing a break statement and falls
through to the following NOUVEAU_GETPARAM_BUS_TYPE case and may end up
re-assigning the getparam->value to an undesired value. Fix this by adding
in the missing break.
Detected by CoverityScan, CID#1460507 ("Missing break in switch")
Fixes: 359088d5b8 ("drm/nouveau: remove trivial cases of nvxx_device() usage")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
drivers/gpu/drm/nouveau/nouveau_bo.c:1434:53: warning: this statement may fall through [-Wimplicit-fallthrough=]
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is much louder then we want. VCPI allocation failures are quite
normal, since they will happen if any part of the modesetting process is
interrupted by removing the DP MST topology in question. So just print a
debugging message on VCPI failures instead.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: f479c0ba4a ("drm/nouveau/kms/nv50: initial support for DP 1.2 multi-stream")
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Currently the uninitialized values in the array reply are printed out
when exec is false and nvkm_pmu_send has not updated the array. Avoid
confusion by only dumping out these values if they have been actually
updated.
Detected by CoverityScan, CID#1271291 ("Uninitialized scaler variable")
Fixes: ebb58dc2ef ("drm/nouveau/pmu: rename from pwr (no binary change)")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Currently, the expression for calculating RON is always going to result
in zero no matter the value of ram->mr[1] because the ! operator has
higher precedence than the shift >> operator. I believe the missing
parentheses around the expression before appying the ! operator will
result in the desired result.
[ Note, not tested ]
Detected by CoveritScan, CID#1324005 ("Operands don't affect result")
Fixes: c25bf7b615 ("drm/nouveau/bios/ramcfg: Separate out RON pull value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Don't populate the array vsoff on the stack but instead make it
static. Makes the object code smaller by 67 bytes:
Before:
text data bss dec hex filename
5753 112 0 5865 16e9 .../nouveau/nvkm/subdev/bios/dp.o
After:
text data bss dec hex filename
5622 176 0 5798 16a6 .../nouveau/nvkm/subdev/bios/dp.o
(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
GF117 appears to use the same register as GK104 (but still with the
general Fermi readout mechanism).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108980
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We still need to set bulk_movable to false when new BOs are added or removed.
v2: also set it to false on removal
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: StDenis, Tom <Tom.StDenis@amd.com>
Tested-by: Przemek Socha <soprwa@gmail.com>
Reviewed-by: Zhou, David(ChunMing) <David1.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We only need to set this to false now when BOs are removed from the LRU.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
Notice that, in this case, variable table_size is not necessary, hence
it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
Notice that, in this case, variable table_size is not necessary, hence
it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current periodic interrupt start point calc in optc
is not clear.
[How]
1. DM convert delta time to lines number and dc will calculate the
start position as per lines number and interrupt type.
2. hwss calculates the start point as per line offset.
3. optc programs vertical interrupts register as per start point
and interrupt source.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The stream->mode_changed flag can persist in the following sequence
of atomic commits:
Commit 1:
Enable CRTC0 (mode_changed = true), Enable CRTC1 (mode_changed = true)
Commit 2:
Disable CRTC1 (mode_changed = false)
In this sequence we want to keep the exiting CRTC0 but it's not in the
atomic state for the commit since it hasn't been modified. In this case
the stream->mode_changed flag persists as true and we don't re-program
the planes for the existing stream.
[How]
The flag needs to be cleared and it makes the most sense to do it within
DC after the state has been committed. Nothing following dc_commit_state
should think that the stream's mode has changed.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor updates used to happen after vblank/flip/stream updates before
the stream update refactor. They now happen before stream updates
which means that they're not going to be synced with fb changes
and that they're going to programmed for pipes that we're disabling
within the same commit.
[How]
Move them after stream updates.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Whenever a stream or plane is added or removed from the context the
pointer will change from old to new. We set lock and validation
needed in these cases. But not all of these cases match update_type
from dm_determine_update_type_for_commit - an example being overlay
plane updates.
There are warnings for a few of these cases that should be fixed.
[How]
We can closer align to DC (and lock_and_validation_needed) by
comparing stream and plane pointers.
Since the old stream/old plane state is never freed until sometime
after the commit tail work finishes we are guaranteed to never get
back the same block of memory when we remove and create a stream or
plane state in the same commit.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This format isn't supported in DC and some IGT tests fail since we
expose support for it.
[How]
Remove it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If a commit updates an overlay plane via the legacy plane IOCTL
then the only plane in the state will be the overlay plane.
Overlay planes need to be added first to the DC context, but in the
scenario above the plane will be added last. This will result in wrong
z-order during rendering.
[How]
If any non-cursor plane has been updated then the rest of the
non-cursor planes should be added to the CRTC state.
The cursor plane doesn't need to be included for stream updates and
locking it will cause performance issues. It should be ignored.
DC requires that the surface count passed during stream updates
be the number of surfaces currently on the stream to enable fast
updates. This previously wasn't the case without this patch, so this
also allows this optimization to occur.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously, a change removed code that would send a pipe set command
to dmcu each time the backlight was set, as it was thought to be
superfluous. However, it is possible for the backlight to be set
before a valid pipe has been set, which causes DMCU to hang after a
DPMS restore on some systems.
[How]
Send a pipe set command to DMCU prior to setting the backlight.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain tests fail after a fresh reboot. This is caused by writing to
registers prior to ungating the stream we're trying to program.
[How]
Make sure the stream is ungated before writing to its registers.
This also enables power-gating plane resources before init_hw
initializes them.
Additionally, this does some refactoring to move gating/ungating
from enable/disable_plane functions to where stream resources are
enabled/disabled.
Signed-off-by: Gary Kattan <gary.kattan@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We are currently losing precision when we convert from
16 bit --> 8 bit --> 16 bit.
[How]
We shouldn't down convert unnecessarily and lose precision.
Keep values at 16 bit and use directly.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want boot to desktop to be seamless
[How]
During init pipes, avoid touching the pipes where GOP has already
enabled the HW to the state we want.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When stream is blanked, pipe set command is sent to dmcu to notify it
that the abm pipe is disabled. When stream is unblanked, no notification is
made to dmcu that the abm pipe has been enabled, resulting in abm not
being enabled in the firmware.
[How]
When stream is unblanked, send a pipe set command to dmcu.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The original change caused a regression, so revert it until the new fix
is ready.
BUG: https://bugs.freedesktop.org/show_bug.cgi?id=109650
This reverts commit 764c85fef41722db0f21558c6c2fb38bee172d19.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 9006c6bd9059cb9807fa863bafc1d776222cb61b.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add missing break statement in order to prevent the code from falling
through to case CB_TARGET_MASK.
This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: dd220a00e8 ("drm/radeon/kms: add support for streamout v7")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The visual corruption due to low display clock value.
Observed on Carrizo 4K@60Hz.
[How]
There was earlier patch for dce_update_clocks:
Adding +15% workaround also to to dce11_update_clocks
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
drm_dp_mst_topology_mgr_suspend() is added into the new reboot
sequence, which disables the UP request at the beginning.
Therefore sideband messages are blocked.
[How]
Finish MST sideband message transaction before UP request is
suppressed.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
According to hardware engineer, WRITE_BURST_LENGTH [9:8] in register
SDMA0_CHICKEN_BITS need to change to 3 for better performance
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Based on a similar patch from Rafael for radeon.
When using ATPX to control dGPU power, the state is not retained
across suspend and resume cycles by default. This can probably
be loosened for Hybrid Graphics (_PR3) laptops where I think the
state is properly retained.
Fixes: c62ec4610c ("PM / core: Fix direct_complete handling for devices with no callbacks")
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
On HP ProBook 4540s, if PM-runtime is enabled in the radeon driver
and the direct-complete optimization is used for the radeon device
during system-wide suspend, the system doesn't resume.
Preventing direct-complete from being used with the radeon device by
setting the DPM_FLAG_NEVER_SKIP driver flag for it makes the problem
go away, which indicates that direct-complete is not safe for the
radeon driver in general and should not be used with it (at least
for now).
This fixes a regression introduced by commit c62ec4610c
("PM / core: Fix direct_complete handling for devices with no
callbacks") which allowed direct-complete to be applied to
devices without PM callbacks (again) which in turn unlocked
direct-complete for radeon on HP ProBook 4540s.
Fixes: c62ec4610c ("PM / core: Fix direct_complete handling for devices with no callbacks")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201519
Reported-by: Ярослав Семченко <ukrkyi@gmail.com>
Tested-by: Ярослав Семченко <ukrkyi@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
(Resend since there was a compile error that I forgot to commit before sending)
If there is a error while doing a copy_from_user() for MSM_INFO_SET_NAME
make sure to truncate the object name so that there isn't a chance that
we'll have random data in the string.
This is on top of [1] reported and fixed by Dan Carpenter.
[1] https://patchwork.freedesktop.org/series/56656/
Fixes: f05c83e774 ("drm/msm: add uapi to get/set debug name")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The copy_to/from_user() functions return the number of bytes remaining
to be copied but we should return -EFAULT to the user.
Fixes: f05c83e774 ("drm/msm: add uapi to get/set debug name")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Try to get the interconnect path for the GPU and vote for the maximum
bandwidth to support all frequencies. This is needed for performance.
Later we will want to scale the bandwidth based on the frequency to
also optimize for power but that will require some device tree
infrastructure that does not yet exist.
v6: use icc_set_bw() instead of icc_set()
v5: Remove hardcoded interconnect name and just use the default
v4: Don't use a port string at all to skip the need for names in the DT
v3: Use macros and change port string per Georgi Djakov
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can directly calculate sdma doorbell indexes in the process doorbell
pages through the doorbell_index structure in amdgpu_device, so no need
to cache them in kgd2kfd_shared_resources any more. This alleviates the
adaptation needs when new SDMA configurations are introduced.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reserved doorbells for SDMA IH and VCN were not properly masked out
when allocating doorbells for CP user queues. This patch fixed that.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
They will be used to inform KFD the doorbell range not usable for CP.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The similar definitions should be consecutive.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxqHJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWl8H/jPI4EipzD2GbnjZ
GaFpMBBjcXBaVmoA+Y69so+7BHx1Ql+5GQtqbK0RHJRb9qEPLw3FBhHNjM/N8Sgf
nSrK+GnBZp9s+k/NR/Yf2RacUR3jhz+Q9JEoQd3u9bFUeQyvE8Rf3vgtoBBwFOfz
+t7N1memYVF3asLGWB4e4sP1YVMGfseTQpSPojvM30YWM86Bv+QtSx1AGgHczQIM
kMKealR8ZPelN6JAXgLhQ5opDojBrE4YKB98pwsMDI6abz0Tz2JLFEUTTxsv5XNN
o/Iz+XDoylskEyxN2unNWfHx7Swkvoklog8J/hDg5XlTvipL/WkT66PHBgcGMNvj
BW9GgU8=
=ZizU
-----END PGP SIGNATURE-----
Merge tag 'v5.0-rc7' into patchwork
Linux 5.0-rc7
* tag 'v5.0-rc7': (1667 commits)
Linux 5.0-rc7
Input: elan_i2c - add ACPI ID for touchpad in Lenovo V330-15ISK
Input: st-keyscan - fix potential zalloc NULL dereference
Input: apanel - switch to using brightness_set_blocking()
powerpc/64s: Fix possible corruption on big endian due to pgd/pud_present()
efi/arm: Revert "Defer persistent reservations until after paging_init()"
arm64, mm, efi: Account for GICv3 LPI tables in static memblock reserve table
sunrpc: fix 4 more call sites that were using stack memory with a scatterlist
include/linux/module.h: copy __init/__exit attrs to init/cleanup_module
Compiler Attributes: add support for __copy (gcc >= 9)
lib/crc32.c: mark crc32_le_base/__crc32c_le_base aliases as __pure
auxdisplay: ht16k33: fix potential user-after-free on module unload
x86/platform/UV: Use efi_runtime_lock to serialise BIOS calls
i2c: bcm2835: Clear current buffer pointers and counts after a transfer
i2c: cadence: Fix the hold bit setting
drm: Use array_size() when creating lease
dm thin: fix bug where bio that overwrites thin block ignores FUA
Revert "exec: load_script: don't blindly truncate shebang string"
Revert "gfs2: read journal in large chunks to locate the head"
net: ethernet: freescale: set FEC ethtool regs version
...
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxqHJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWl8H/jPI4EipzD2GbnjZ
GaFpMBBjcXBaVmoA+Y69so+7BHx1Ql+5GQtqbK0RHJRb9qEPLw3FBhHNjM/N8Sgf
nSrK+GnBZp9s+k/NR/Yf2RacUR3jhz+Q9JEoQd3u9bFUeQyvE8Rf3vgtoBBwFOfz
+t7N1memYVF3asLGWB4e4sP1YVMGfseTQpSPojvM30YWM86Bv+QtSx1AGgHczQIM
kMKealR8ZPelN6JAXgLhQ5opDojBrE4YKB98pwsMDI6abz0Tz2JLFEUTTxsv5XNN
o/Iz+XDoylskEyxN2unNWfHx7Swkvoklog8J/hDg5XlTvipL/WkT66PHBgcGMNvj
BW9GgU8=
=ZizU
-----END PGP SIGNATURE-----
Merge v5.0-rc7 into drm-next
Backmerging for nouveau and imx that needed some fixes for next pulls.
Signed-off-by: Dave Airlie <airlied@redhat.com>
For the reusability of the enum port in other driver modules
(like mei_hdcp), enum port definition is moved from I915 local header
intel_display.h to drm/i915_drm.h
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Fix subject prefix.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1550219730-17734-3-git-send-email-ramalingam.c@intel.com
Carried over from radeon, but no longer used.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Given a master fd we can then override the priority of the context
in another fd.
Using these overrides was recommended by Christian instead of trying
to submit from a master fd, and I am adding a way to override a
single context instead of the entire process so we can only upgrade
a single Vulkan queue and not effectively the entire process.
Reused the flags field as it was checked to be 0 anyways, so nothing
used it. This is source-incompatible (due to the name change), but
ABI compatible.
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise we interpret the file private data as drm & amdgpu data
while it might not be, possibly allowing one to get memory corruption.
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I don't see another way to figure out if a ring is initialized if
the hardware block might not be initialized.
Entities have been fixed up to handle num_rqs = 0.
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some blocks in amdgpu can have 0 rqs.
Job creation already fails with -ENOENT when entity->rq is NULL,
so jobs cannot be pushed. Without a rq there is no scheduler to
pop jobs, and rq selection already does the right thing with a
list of length 0.
So the operations we need to fix are:
- Creation, do not set rq to rq_list[0] if the list can have length 0.
- Do not flush any jobs when there is no rq.
- On entity destruction handle the rq = NULL case.
- on set_priority, do not try to change the rq if it is NULL.
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Passing an object_count of sufficient size will make
object_count * 4 wrap around to be very small, then a later function
will happily iterate off the end of the object_ids array. Using
array_size() will saturate at SIZE_MAX, the kmalloc() will fail and
we'll return an -ENOMEM to the norty userspace.
Fixes: 62884cd386 ("drm: Add four ioctls for managing drm mode object leases [v7]")
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Dave Airlie <airlied@redhat.com>
The prepare_fb call always happens on new_plane_state.
The drm_atomic_helper_cleanup_planes checks to see if
plane state pointer has changed when deciding to call cleanup_fb on
either the new_plane_state or the old_plane_state.
For a non-async atomic commit the state pointer is swapped, so this
helper calls prepare_fb on the new_plane_state and cleanup_fb on the
old_plane_state. This makes sense, since we want to prepare the
framebuffer we are going to use and cleanup the the framebuffer we are
no longer using.
For the async atomic update helpers this differs. The async atomic
update helpers perform in-place updates on the existing state. They call
drm_atomic_helper_cleanup_planes but the state pointer is not swapped.
This means that prepare_fb is called on the new_plane_state and
cleanup_fb is called on the new_plane_state (not the old).
In the case where old_plane_state->fb == new_plane_state->fb then
there should be no behavioral difference between an async update
and a non-async commit. But there are issues that arise when
old_plane_state->fb != new_plane_state->fb.
The first is that the new_plane_state->fb is immediately cleaned up
after it has been prepared, so we're using a fb that we shouldn't
be.
The second occurs during a sequence of async atomic updates and
non-async regular atomic commits. Suppose there are two framebuffers
being interleaved in a double-buffering scenario, fb1 and fb2:
- Async update, oldfb = NULL, newfb = fb1, prepare fb1, cleanup fb1
- Async update, oldfb = fb1, newfb = fb2, prepare fb2, cleanup fb2
- Non-async commit, oldfb = fb2, newfb = fb1, prepare fb1, cleanup fb2
We call cleanup_fb on fb2 twice in this example scenario, and any
further use will result in use-after-free.
The simple fix to this problem is to block framebuffer changes
in the drm_atomic_helper_async_check function for now.
v2: Move check by itself, add a FIXME (Daniel)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Cc: <stable@vger.kernel.org> # v4.14+
Fixes: fef9df8b59 ("drm/atomic: initial support for asynchronous plane update")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/275364/
This prevents us from accessing extended registers in tools like
umr. The register access functions already check if the offset
is beyond the BAR size and use the indirect accessors with locking
so this is safe.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are several statements that are incorrectly indented. Fix these.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Missing firmware declaration caused firmware requirement to
not be noted by the module and may cause firmware to not
be available in initrd.
Fixes: bc4b539e38 "drm/amdgpu: remove old CI DPM implementation"
Reviewed-by: James Zhu <James.Zhu@amd.com>
Tested-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When ring hang happens amdgpu_dm_commit_planes during flip is holding
the BO reserved and then stack waiting for fences to signal in
reservation_object_wait_timeout_rcu (which won't signal because there
was a hnag). Then when we try to shutdown display block during reset
recovery from drm_atomic_helper_suspend we also try to reserve the BO
from dm_plane_helper_cleanup_fb ending in deadlock.
Also remove useless WARN_ON
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
They are no longer used, so delete them to avoid confusion.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CP_RB_DOORBELL_RANGE_LOWER/UPPER and CP_MEC_DOORBELL_RANGE_LOWER/UPPER
are used for waking up an idle scheduler and for power gating support.
Usually the first few doorbells in pci doorbell bar are used for RB
and all leftover for MEC. This patch fixes the incorrect settings.
Theoretically, gfx ring doorbells should come before all MEC doorbells
to be consistent with the design. However, since the doorbell
allocations are agreed by all and we are not free to change them, also
considering the kernel MEC ring doorbells which are before gfx ring
doorbells are not used often, we compromise by leaving the doorbell
allocations unchanged.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Temporarily removing eviction fences to avoid triggering them by
accident is no longer necessary due to the fence_owner logic in
amdgpu_sync_resv.
As a result the ef_list usage of amdgpu_amdkfd_remove_eviction_fence
and amdgpu_amdkfd_add_eviction_fence are no longer needed.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use FENCE_OWNER_KFD to synchronize PT/PD initialization and clearing
of page table entries. This avoids triggering KFD eviction fences on
the PD reservation objects of compute VMs.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The fence_owner logic in amdgpu_sync_wait will allow waiting without
having to temporarily remove eviction fences.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Creates a temporary sync object to wait for the BO reservation. This
generalizes amdgpu_vm_wait_pd.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
sriov's gpu_recover inside xgpu_ai_mailbox_flr_work would cause duplicate recover in TDR.
TDR's gpu_recover would be triggered by amdgpu_job_timedout,
that could avoid vk-cts failure by unexpected recover.
Signed-off-by: Wentao Lou <Wentao.Lou@amd.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove the callback and call the dispatcher directly.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are cases (in mesa and applications) where one would open the
primary node without properly authenticating the client.
Sometimes we don't check if the authentication succeeds, but there's
also cases we simply forget to do it.
The former was a case for Mesa where it did not not check the return
value of drmGetMagic() [1]. That was fixed recently although, there's
the question of older drivers or other apps that exbibit this behaviour.
While omitting the call results in issues as seen in [2] and [3].
In the libva case, libva itself doesn't authenticate the DRM client and
the vaGetDisplayDRM documentation doesn't mention if the app should
either.
As of today, the official vainfo utility doesn't authenticate.
To workaround issues like these, some users resort to running their apps
under sudo. Which admittedly isn't always a good idea.
Since any DRIVER_RENDER driver has sufficient isolation between clients,
we can use that, for unauthenticated [primary node] ioctls that require
DRM_AUTH. But only if the respective ioctl is tagged as DRM_RENDER_ALLOW.
v2:
- Rework/simplify if check (Daniel V)
- Add examples to commit messages, elaborate. (Daniel V)
v3:
- Use single unlikely (Daniel V)
[1] 2bc1f5c2e7/src/egl/drivers/dri2/platform_wayland.c (L1136)
[2] https://lists.freedesktop.org/archives/libva/2016-July/004185.html
[3] https://gitlab.freedesktop.org/mesa/kmscube/issues/1
Testcase: igt/core_unauth_vs_render
Cc: intel-gfx@lists.freedesktop.org
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114085408.15933-2-emil.l.velikov@gmail.com
Currently only an authenticated master can authenticate another client.
In practise the client can only be master if CAP_SYS_ADMIN is present,
although having the CAP also sets the client as authenticated.
Thus DRM_AUTH in AUTH_MAGIC's "DRM_AUTH | DRM_MASTER" is superfluous.
Notices while working on IGT tests.
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114084305.15141-1-emil.l.velikov@gmail.com
