Commit Graph

133365 Commits

Author SHA1 Message Date
Jouni Malinen
f0ed85c6c7 ath9k: Virtual wiphy pause/unpause functionality
Allow virtual wiphys to be paused/unpaused to allow off-channel
operations. Pause will stop all TX queues for the wiphy and move the
STA into power save mode if in managed mode. Unpause wakes up the TX
queues and notifies the AP that the STA woke up if in managed mode.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:45 -05:00
Jouni Malinen
b93bce2a5e ath9k: Configure RX filter for multi-BSSID broadcast
Allow RX filter to pass through all broadcast/multicast frames (i.e.,
no BSSID filtering) if virtual interfaces are used. Software filtering
will be used in this case to drop broadcast/multicast frames for
foreign BSSIDs.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:45 -05:00
Jouni Malinen
c52f33d05e ath9k: Add support for multiple secondary virtual wiphys
The new struct ath_softc::sec_wiphy array is used to store information
about virtual wiphys and select which wiphy is used in calls to
mac80211. Each virtual wiphy will be assigned a different MAC address
based on the virtual wiphy index.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:45 -05:00
Jouni Malinen
bce048d77d ath9k: Add data structure for supporting virtual radio/wiphy operation
This is the initial step in allowing ath9k to register multiple
virtual radios (wiphys). The goal of virtual radios is to allow the
same radio to be shared for multiple virtual interfaces that may
operate on different channels. The mac80211 virtual interface support
is designed only for single channel operation and as such, it is not
suitable for this type of use. Anyway, it can be used on top of the
virtual radio concept, if desired (e.g., use two virtual radios to
handle two channels and then add multiple mac80211 virtual interfaces
on top of each virtual radio).

The new struct ath_wiphy is now registered as the driver data
structure for wiphy. This structure has a pointer to the shared (among
virtual wiphys of the same physical radio) struct ath_softc data. The
primary wiphy maintains the allocated memory for ath_softc. Secondary
(virtual) wiphys will only allocate the new ath_wiphy structure.

Registration of secondary wiphys is added in a separate patch.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:44 -05:00
Jouni Malinen
8ca21f0185 ath9k: Set BSSID mask based on configured interfaces
Instead of using a hardcoded BSSID mask (mask for own addresses),
iterate through all active interfaces and determine the minimal mask
that covers all local addresses.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:44 -05:00
Jouni Malinen
2c3db3d51e ath9k: Cleanup multiple VIF processing
Replace the internal sc_vaps array and index values by using vif
pointer from mac80211. Allow multiple VIPs to be registered. Though,
number of beaconing VIFs is still limited by ATH_BCBUF (currently
1). Multiple virtual STAs support is not yet complete, but at least
the data structures should now be able to handle this.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:44 -05:00
Ivo van Doorn
860559fe68 rt2x00: Export all register stats through debugfs
By exporting the register base, and word size to userspace
through debugfs it will be easier to create scripts which
parse the register information. This makes debugging and
register dumps information easier.

This will break my previous scripts which dumped and parsed
all information, but since this is only for debugging purposes
this change should not be a problem.

Dumpfiles created with the old version can be easily manually
edited to make them compatible with this new approach, which
means there will be no problems comparing dumps from the
different versions either.

Also be more consistent with using tabs to seperate different
fields.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:44 -05:00
Jouni Malinen
d216aaa674 ath9k: Clean up setkey operations
There is no need to use ath_keyset() wrapper for
ath9k_hw_set_keycache_entry() calls. In addition, improve the comments
describing the key setting operations.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:43 -05:00
Gabor Juhos
aebe2b5624 ath9k: fix AR_TXCFG_DMASZ_MASK value
The current bitmask is invalid, because the tx dma size is a 3 bit wide
value.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:43 -05:00
Sujith
b75bc150af ath9k: Remove unused variables in struct ath_beacon_config
We don't store the beacon timestamp internally, nor
do we do any TIM handling in ath9k.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:43 -05:00
Sujith
2554935b08 ath9k: Lock config_interface() callback with a mutex
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:42 -05:00
Sujith
b238e90e99 ath9k: Handle TSF properly for AP mode
The TSF has to be reset only once, upon bringing
the interface up in AP mode. For any beacon reconfigure calls
after that, resetting the TSF results in incorrect beacon generation.
The only exception is a change in the beacon interval,
which is indicated to the driver by mac80211 through
IEEE80211_CONF_CHANGE_BEACON_INTERVAL, handle this properly.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:42 -05:00
Sujith
5379c8a266 ath9k: Split beacon configuration into mode specific routines
This makes the code easier to understand.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:42 -05:00
Sujith
9546aae086 ath9k: Cleanup beacon stuck processing
We never use SC_OP_NO_RESET, it is not configurable at all.
Remove all code that deals with this flag and make beacon
stuck processing simple.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:41 -05:00
Sujith
9fc9ab0a69 ath9k: Scrub beacon.c
Remove useless comments, fix indentation.
Also, remove all occurrences of ASSERT(vif) which are not needed.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:41 -05:00
Sujith
0c98de6535 ath9k: Use new scan notifiers from mac80211
The only use case for this right now is ANI calibration,
but more might come up in the future.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:41 -05:00
Sujith
707c1b4e68 mac80211: Update IBSS beacon timestamp properly
In IBSS mode, the beacon timestamp has to be filled with the
BSS's timestamp when joining, and set to zero when creating
a new BSS.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:40 -05:00
Alina Friedrichsen
0ad65bd7e1 ath5k: Set TSF fix
The old code doesn't work correctly e.g. on newer chipsets like AR5418+AR2122 and AR5416+AR2133.

Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:40 -05:00
Alina Friedrichsen
b9a1619763 ath9k: Set TSF fix
The old code doesn't work correctly e.g. on newer chipsets like AR5418+AR2122 and AR5416+AR2133.

Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:40 -05:00
Michael Buesch
ce4fbdbf16 b43: Pass more RX flags to mac80211
This changes the RX handler to pass more status flags to mac80211.
It also changes part of the drop policy, if bad frames were requested. (Note that
currently mac80211 will throw a WARN_ON in that case. But nothing bad will happen).

This also removes some obsolete unused timestamping code.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:40 -05:00
Alina Friedrichsen
91ed19f5f6 ath9k: Fix FIF_BCN_PRBRESP_PROMISC handling
So that a new created IBSS network
doesn't break on the first scan.

It seems to Sujith and me that this
stupid code unnecessary, too.

So remove it...

Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:39 -05:00
Vivek Natarajan
541d8dd5e8 ath9k: Handle power modes in isr for power save.
Restore network sleep mode in isr if power save is enabled.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:39 -05:00
Sujith
9331ec8060 ath9k: Fill in rate_update mac80211 callback
This callback can be used to handle dynamic 20/40,
and changes in the operating channel's HT parameters.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:39 -05:00
Vivek Natarajan
25c9c87528 mac80211: Always send a null data frame if TIM bit is set.
If the AP thinks we are in power save state eventhough we are not truly
in that state, it sets the TIM bit and does not send a data frame unless
we send a null data frame to correct the state in the AP.
This might happen if the null data frame for wake up is lost in the air
after we disable power save.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:38 -05:00
Jouni Malinen
e0caf9eaae ath9k: Remove unused key xoring
This is not used anywhere in ath9k and is just making the code more
confusing.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:38 -05:00
Jouni Malinen
672903b329 ath9k: Document keycache operations
There are number of small details about the keycache operations that
are very easy to miss (and forget), so better include detailed
comments in ath9k_hw_set_keycache_entry() to avoid having to figure
out this every time when having to touch this area.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:38 -05:00
Sujith
e65c22633c mac80211: Fix TKIP/WEP HT capability handling
There is no need to parse the AP's HT capabilities if
the STA uses TKIP/WEP cipher. This allows the rate control
module to choose the correct(legacy) rate table.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:37 -05:00
Frank Seidel
a412c8040d iwlwifi: reduce stack size
Reduce stack memory footprint of iwlwifi.
(From >1000 bytes for each *_table_read
on i386 down to 32)

Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:37 -05:00
Ivo van Doorn
64abd80330 rt2x00: Fix SW antenna diversity
Software antenna tuning is broken because of an function
ordering problem during rt2x00link_tuner().

rt2x00link_precalculate_signal()
rt2x00leds_led_quality()
rt2x00lib_antenna_diversity()

rt2x00link_precalculate_signal() will reset the quality TX/RX counters,
however rt2x00lib_antenna_diversity() requires the RX counter to
see what RSSI value must be used for a particular antenna.
We can't change the ordering since rt2x00lib_antenna_diversity() might
reset other statistics which are needed by the function called earlier.

Move the reset of the quality TX/RX counters into a seperate function
and move the call to after rt2x00lib_antenna_diversity().

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:37 -05:00
Abhijeet Kolekar
14d2aac580 iwl3945 : use iwl_activate_qos
3945 can use iwl_activate_qos instead of iwl3945_activate_qos.
Patch does two things
1) Patch adds iwl_activate_qos in core library.
2) 3945 makes use of iwl_activate_qos.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:36 -05:00
Abhijeet Kolekar
2a4ddaabe0 iwl3945: add iwl3945_setup_mac
Patch does following,
1) mac80211's shared data is now initialized in iwl3945_setup_mac.
2) Set the rfkill to right state after initialization

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:36 -05:00
Reinette Chatre
c8f16138b5 iwlwifi: fix *pci_probe error flow
for iwlagn:
- Have to free eeprom of version check fails - otherwise we end up with
  memory leak.
- Include removal of workqueue (created in _setup_deferred_work) in error
  handling.

for iwl3945:
- Fix a few places to jump to correct error handling.
- Reorganize error handling to match with code flow.
- Include iwl_free_channel_map as part of error handling.
- Include releasing eeprom as part of error handling.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:36 -05:00
Abhijeet Kolekar
6e21f15cac iwl3945: unify set key flow with iwlwifi
unify the set key flow with iwlwifi.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:36 -05:00
Abhijeet Kolekar
7c4cbb6ee0 iwl3945: synchronize timestamp with uCode
In IBSS, TSF maintains local clock counters at each station. Network
Synchronization follows a completely distributed scheme where beacon frames
are generated. Each station maintain its own TSF timestamp, extracted from
beacon timestamps they recieved. Following patch synchronize this beacon timestamp
with uCode.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:35 -05:00
Jay Sternberg
39e6d2256b iwlwifi: update 5150 API version to support new firmware
update API to support new numbering that is used for other newer devices.
5150 ucode has not been released yet, so the first released API will be v2.
For those who do have a v1 API the driver does have backward compatibility
support new value of REPLY_TX_POWER_DBM_CMD

Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:35 -05:00
Johannes Berg
24776cfd55 mac80211: Fix quality reporting for wireless stats
Since "mac80211/cfg80211: move iwrange handler to cfg80211", the
results for link quality from "iwlist scan" and "iwconfig" commands
have been very different. The results are now consistent.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported- and tested-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:35 -05:00
Michael Buesch
e79c1ba84c ssb: Add SPROM fallback support
This adds SSB functionality to register a fallback SPROM image from the
architecture setup code.

Weird architectures exist that have half-assed SSB devices without SPROM attached to
their PCI busses. The architecture can register a fallback SPROM image that is
used if no SPROM is found on the SSB device.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:32 -05:00
Sujith
e31ae05083 mac80211: Notify the driver only when the beacon interval changes
Currently, the driver is unconditionally notified of beacon
interval. This is a problem in AP mode, because the driver has
to know that the beacon interval has actualy changed to recalculate
TBTT and reset the HW TSF. Fix this to make mac80211 notify the driver
only when the beacon interval has been reconfigured to a new value.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:32 -05:00
Jiri Slaby
db5b4f7ae3 ath5k: fix hw rate index condition
Make sure we print out a warning when the index is out of bounds,
i.e. even on hw_rix == AR5K_MAX_RATES.

Also change to WARN and print text with the reported hw_rix.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:32 -05:00
Jouni Malinen
3f53dd64f1 ath9k: Fix hw crypto configuration for TKIP in AP mode
Incorrect Michael MIC key (RX, should have been TX) was set for the
group key in AP mode. This resulted in all broadcast frames triggering
Michael MIC errors and eventual TKIP countermeasures. The change here
sets the correct Michael MIC key based on whether the local end is the
authenticator (well, AP for now).

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Tested-by: Pat Erley <pat-lkml@erley.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:31 -05:00
Frank Seidel
998a5a7d6a airo: reduce stack memory footprint
Applying kernel janitors todos (reduce stack
footprint where possible) to airo wireless driver.
(Before 1124 bytes on i386, now 876)

Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:31 -05:00
Roel Kluin
b837e606d1 wireless, wavelan: spin off by 1
spin can reach -1 after the loop, so 0 is still success.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:31 -05:00
Vasanthakumar Thiagarajan
fa09632b02 ath9k: Remove ununsed ack duration stuff with long/short preamble
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:31 -05:00
Vasanthakumar Thiagarajan
f40154e7f7 ath9k: Configure Power control register appropriately for h/w with 4k eeprom
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:30 -05:00
Alina Friedrichsen
5fe73197d3 zd1211rw: Implement get_tsf()
This patch implements get_tsf() of ieee80211_ops in the zd1211rw driver.

Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:30 -05:00
Jouni Malinen
b3bd89ce95 ath9k: Add module parameter to disable hardware crypto
nohwcrypt=1 module parameter can now be used to disable hardware
crypto in ath9k. While the hardware acceleration handles most cases,
it may be useful to be able to force mac80211 software implementation
to be used for some tests, e.g., with virtual interface combinations
that may not yet be supported in the key cache configuration. In
addition, this allows management frame protection to be tested with
older hardware revisions.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:30 -05:00
David S. Miller
508827ff0a Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/tokenring/tmspci.c
	drivers/net/ucc_geth_mii.c
2009-03-05 02:06:47 -08:00
Patrick McHardy
72e2240f18 bonding: Fix device passed into ->ndo_neigh_setup().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-05 01:57:44 -08:00
David S. Miller
77827a7cf3 Merge branch 'master' of /home/davem/src/GIT/linux-2.6/ 2009-03-04 23:59:54 -08:00
David S. Miller
9d40bbda59 vlan: Fix vlan-in-vlan crashes.
As analyzed by Patrick McHardy, vlan needs to reset it's
netdev_ops pointer in it's ->init() function but this
leaves the compat method pointers stale.

Add a netdev_resync_ops() and call it from the vlan code.

Any other driver which changes ->netdev_ops after register_netdevice()
will need to call this new function after doing so too.

With help from Patrick McHardy.

Tested-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-04 23:46:25 -08:00