To prevent I/O as soon as possible at card removal, a new detect work is
re-scheduled without a delay to let a rescan remove the card device as
soon as possible.
Additionally, MMC_CAP2_DETECT_ON_ERR can now be used to handle "slowly"
removed cards that a scheduled detect work did not detect as removed.
To prevent further I/O requests for these lingering removed cards,
check if card has been removed and then schedule a detect work to
properly remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is added just debug message. Almost features need to use the
CMD23. But we didn't see the debug message for sbc. If sbc's message
can see, should be help for debugging. (We can check whether use the
cmd23 or not.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC-4.5 data tag feature will be used to store the file system meta-data
in the tagged region of eMMC. This will improve the write and subsequent
read transfer time for the meta data.
Signed-off-by: Saugata Das <saugata.das@linaro.org>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Even if cards supports 1.8V I/O voltage those should anyway be
initialized at 3.3V I/O according to (e)MMC, SD and SDIO specs.
Some eMMC and embedded SDIO devices are able to be initialized
at 1.8V as well, but it is better to be safe.
Do note that initialization in this context means that the card
has been completely powered off, otherwise the card will remain
at the last I/O voltage level that were negotitiated.
Due to the above being taken care of the suspend/resume issues
for UHS-I SD-cards has been fixed.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
A recent commit "mmc: core: Use delayed work in clock gating framework"
(597dd9d79c) introduced a default 200ms delay before clock gating
actually takes place. This means that every time an MMC interface
becomes idle it first stays on for 200ms before gating its clock. This
leads to increased power consumption and is therefore a clear regression.
This patch restores the original behaviour by setting the default delay
to 0. Users prioritising throughput over power efficiency can still
modify the delay via sysfs.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Found this issue during code review. Actually, there are two issues which
both compensate together in lucky case. In unlucky case the bus width
probing might not work as expected.
Signed-off-by: Jurgen Heeks <jurgen.heeks@nokia.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Modified the mmc_poweroff to resume before sending the poweroff
notification command. In sleep mode only AWAKE and RESET commands are
allowed, so before sending the poweroff notification command resume from
sleep mode and then send the notification command.
PowerOff Notify is tested on a Synopsis Designware Host Controller
(eMMC 4.5). The suspend to RAM and resume works fine.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Tested-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Saugata Das <saugata.das@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
There is an understood mismatch between the voltage the host controller is
set to and the voltage supplied to the card by a fixed voltage regulator.
Teaching the driver to accept the mismatch is overly complicated. Instead
just accept the regulator's voltage.
This patch adds MMC_CAP2_BROKEN_VOLTAGE.
If the voltage didn't satisfy between min_uV and max_uV, try to change
the voltage in core.c. When changing the voltage, maybe use
regulator_set_voltage().
In regulator_set_voltage(), check the below condition.
/* sanity check */
if (!rdev->desc->ops->set_voltage &&
!rdev->desc->ops->set_voltage_sel) {
ret = -EINVAL;
goto out;
}
If some board should use the fixed-regulator, always return -EINVAL.
Then, eMMC didn't initialize always.
So if use a fixed-regulator, we need to add the MMC_CAP2_BROKEN_VOLTAGE.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes the failure of low speed mmc card detection.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ensure clocks are always enabled before any interaction with the
host controller driver. This makes sure that there is no race
between host execution and the core layer turning off clocks
in different context with clock gating framework.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
A UHS sdio card that fails initialization at 1.8v signaling is not in
UHS mode. We cannot use the speed in the the cis to reflect the bus
speed as this is the maxiumum value and will not reflect the fact
that the host is operating at a lower (non uhs) bus speed.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Reviewed-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HHrh
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/rustyrussell/linux
Autogenerated GPG tag for Rusty D1ADB8F1: 15EE 8D6C AB0E 7F0C F999 BFCB D920 0E6C D1AD B8F1
* tag 'for-linus' of git://github.com/rustyrussell/linux:
module_param: check that bool parameters really are bool.
intelfbdrv.c: bailearly is an int module_param
paride/pcd: fix bool verbose module parameter.
module_param: make bool parameters really bool (drivers & misc)
module_param: make bool parameters really bool (arch)
module_param: make bool parameters really bool (core code)
kernel/async: remove redundant declaration.
printk: fix unnecessary module_param_name.
lirc_parallel: fix module parameter description.
module_param: avoid bool abuse, add bint for special cases.
module_param: check type correctness for module_param_array
modpost: use linker section to generate table.
modpost: use a table rather than a giant if/else statement.
modules: sysfs - export: taint, coresize, initsize
kernel/params: replace DEBUGP with pr_debug
module: replace DEBUGP with pr_debug
module: struct module_ref should contains long fields
module: Fix performance regression on modules with large symbol tables
module: Add comments describing how the "strmap" logic works
Fix up conflicts in scripts/mod/file2alias.c due to the new linker-
generated table approach to adding __mod_*_device_table entries. The
ARM sa11x0 mcp bus needed to be converted to that too.
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Performing MMC block IO with simultaneous STR can lead to a deadlock: the
mmc_pm_notify() function claims the host and then calls bus .remove()
method, which lands in mmc_blk_remove(), which calls mmc_blk_remove_req()
then it goes to -> mmc_cleanup_queue() -> kthread_stop(), which waits for
the mmc-block thread to stop. If the mmc-block thread at that time is
processing block requests, it will also try to claim the host in
mmc_blk_issue_rq() and block there. This patch fixes the problem by
calling .remove() before claiming the host.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the support of the HS200 bus speed for eMMC 4.5 devices.
The eMMC 4.5 devices have support for 200MHz bus speed. The function
prototype of the tuning function is modified to handle the tuning
command number which is different in sd and mmc case.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Turning the cache off implies flushing cache which doesn't define
maximum timeout unlike cache-on. This patch will apply the generic
CMD6 timeout only for cache-on. Additionally the kernel message is
added for checking failure case of cache-on.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host may now use MMC_CAP2_NO_SLEEP_CMD to disable the use
of eMMC sleep/awake command.
This option can be used when your platform has a buggy
kernel crash dump software, which is supposed to store
the dump on the eMMC, but is not able to wake up the eMMC
from sleep state.
In particular, failures have been seen with u-boot; even if
it is fixed there, platforms will be slow to update their
bootloader binaries.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Hanumath Prasad <hanumath.prasad@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
While calling mmc_cache_ctrl() a host is not claimed. This patch
adds the mmc_try_claim_host() for quick response in suspend.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds a primitive helper to support card hotplug detection on
platforms, where a GPIO, capable of producing interrupts, is used for
detection of card-insertion and -removal events.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes the wrong comparison before setting the interface
voltage in DDR mode.
The assignment to the variable ddr before comaprison is either
ddr = MMC_1_2V_DDR_MODE; or ddr == MMC_1_8V_DDR_MODE. But the comparison
is done with the extended csd value if ddr == EXT_CSD_CARD_TYPE_DDR_1_2V.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Philip Rakity <prakity@marvell.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
c31b50e (mmc: core: Use delayed work in clock gating framework,
2011-11-14) missed a few things during review:
o A useless pr_info()
o milliseconds was written as two words
o The sysfs file had units in its output
Fix all three problems.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable boot partitions to be read-only locked until next power on via
a sysfs entry. There will be one sysfs entry for each boot partition:
/sys/block/mmcblkXbootY/ro_lock_until_next_power_on
Each boot partition is locked by writing 1 to its file.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: John Beckett <john.beckett@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a function mmc_detect_card_removed() which upper layers can use to
determine immediately if a card has been removed. This function should
be called after an I/O request fails so that all queued I/O requests
can be errored out immediately instead of waiting for the card device
to be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for sdio UHS cards per the version 3.0
spec.
UHS mode is only enabled for version 3.0 cards when both the
host and the controller support UHS modes.
1.8v signaling support is removed if both the card and the
host do not support UHS. This is done to maintain
compatibility and some system/card combinations break when
1.8v signaling is enabled when the host does not support UHS.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Aaron Lu <Aaron.lu@amd.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Tested-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Current clock gating framework disables the MCI clock as soon as the
request is completed and enables it when a request arrives. This aggressive
clock gating framework, when enabled, cause following issues:
When there are back-to-back requests from the Queue layer, we unnecessarily
end up disabling and enabling the clocks between these requests since 8MCLK
clock cycles is a very short duration compared to the time delay between
back to back requests reaching the MMC layer. This overhead can effect the
overall performance depending on how long the clock enable and disable
calls take which is platform dependent. For example on some platforms we
can have clock control not on the local processor, but on a different
subsystem and the time taken to perform the clock enable/disable can add
significant overhead.
Also if the host controller driver decides to disable the host clock too
when mmc_set_ios function is called with ios.clock=0, it adds additional
delay and it is highly possible that the next request had already arrived
and unnecessarily blocked in enabling the clocks. This is seen frequently
when the processor is executing at high speeds and in multi-core platforms
thus reduces the overall throughput compared to if clock gating is
disabled.
Fix this by delaying turning off the clocks by posting request on
delayed workqueue. Also cancel the unscheduled pending work, if any,
when there is access to card.
sysfs entry is provided to tune the delay as needed, default
value set to 200ms.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is to expose the actual SDCLK frequency in
/sys/kernel/debug/mmcX/ios entry.
For example, if the max clk for a normal speed card is 20MHz this
is reported in /sys/kernel/debug/mmcX/ios. Unfortunately the actual
SDCLK frequency (i.e. Baseclock / divisor) is not reported at all:
for example, in that case, on Arasan HC, it should be 48/4=12 (MHz).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch allows any block size to be set on the SDIO link,
and still have an arbitrary sized packet (adjusted in size by
using sdio_align_size) transferred in an optimal way
(preferably one transfer).
Previously if the block size was larger than the default of
512 bytes and the transfer size was exactly one block size
(possibly thanks to using sdio_align_size to get an optimal
transfer size), it was sent as a number of byte transfers instead
of one block transfer. Also if the number of blocks was
(max_blocks * N) + 1, the tranfer would be conducted with a number
of blocks and finished off with a number of byte transfers.
When doing this change it was also possible to break out the quirk
for broken byte mode in a much cleaner way, and collect the logic of
when to do byte or block transfer in one function instead of two.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add new macros for the high speed 50MHz case, rather than having
a confusing reuse of the value for UHS SDR50, which is 100MHz.
Reported-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When SDIO runtime PM was originally introduced, we immediately faced
two regressions with two different chipsets, and in response decided
not to enable it by default.
With the recent work on the 8686 we hoped we found all the gotchas,
so 08da834 did make sense (at least experimentally).
Unfortunately we now see that some setups out there still refuse to
work when SDIO runtime PM is enabled by default (see
http://www.spinics.net/lists/linux-mmc/msg11161.html), and obviously
we can't live with these kind of regressions.
This reverts commit 08da834a24.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_suspend_host() tries to claim host during suspend
and release it only when the bus suspend operation is
compeleted. If CONFIG_MMC_UNSAFE_RESUME is defined and
the host is flagged as removable, mmc_suspend_host()
tries to remove the card. In this process, the file system
sync can get blocked trying to acquire host which is already
claimed by mmc_suspend_host() causing deadlock.
Fix this deadlock by releasing host before ->remove() is called.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix wrong bus_ops->sleep check. (This isn't expected to have real-world
consequences, because the mmc core always defines both 'awake' and
'sleep' ops.)
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The eMMC 4.5 devices respond to only RESET and AWAKE command in the
sleep state. Hence the mmc switch command to notify power off state
should be sent before the device enters sleep state.
This patch fixes the same.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch skips the setting of the power notify state variable
for non eMMC 4.5 devices. Also fixes the problem of omap_hsmmc
noisy/broken for suspend resume reported by Kevin Hilman.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Adds a quirk that sets the data read timeout to a fixed value instead
of relying on the information in the CSD. The timeout value chosen
is 300ms since that has proven enough for the problematic cards found,
but could be increased if other cards require this.
This patch also enables this quirk for certain Micron cards known to
have this problem.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Once the implicit use of module.h is prevented, these files will
fail to find the stat.h header content.
Fix up the implicit usage expectations in advance of the cleanup.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These two basic defines were everywhere, simply because module.h
was also everywhere. But we are cleaning up the latter. So make
the exporters actually call out their need for the include.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Code cleanup, putting all eMMC 4.5 detection cases together.
This patch removes one if-statement and assembles all. And it also
removes variable initialization below else-statement -- all members
of card structure are already set to zero at card-init.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
While trying to suspend the mmc host there could still be
ongoing requests that we need to wait for. At the same time
a device driver must respond to a suspend request rather quickly.
Instead of potentially wait "forever" by claiming the host we now
"try" to claim the host instead. If it fails, -EBUSY is returned.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Table 6-2: CCCR bit Definitions, address 00h. Part E1 SDIO Simplified
Specification Version 3.00, Feb. 25, 2011.
This patch has been tested with Marvell WLAN device SD8797.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Here is Essential conditions to indicate Version 3.00 Card
(SD_SPEC=2 and SD_SPEC3=1) :
(1) The card shall support CMD6
(2) The card shall support CMD8
(3) The card shall support CMD42
(4) User area capacity shall be up to 2GB (SDSC) or 32GB (SDHC)
User area capacity shall be more than or equal to 32GB and
up to 2TB (SDXC)
(5) Speed Class shall be supported (SDHC or SDXC)
So even if SD card doesn't support any of the newly defined
UHS-I bus speed mode, it can advertise itself as SD3.0 cards
as long as it supports all the essential conditions of
SD3.0 cards. Given this, these type of cards should atleast
run in High Speed mode @50MHZ if it supports HS.
But current initialization sequence for SD3.0 cards is
such that these non-UHS-I SD3.0 cards runs in Default
Speed mode @25MHz.
This patch makes sure that these non-UHS-I SD3.0 cards run
in High Speed Mode @50MHz.
Tested this patch with SanDisk Extreme SDHC 8GB Class 10 card.
Reported-by: "Hiremath, Vaibhav" <hvaibhav@ti.com>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
HPI command is defined in eMMC4.41.
This feature is important for eMMC4.5 devices.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds cache feature of eMMC4.5 Spec.
If device supports cache capability, host can utilize some specific
operations.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch will apply the generic CMD6 timeout to switch command
for power class.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC v4.5 supports the DISCARD feature (CMD38). It's different from
trim and there's no check bit. Currently it's only supported at v4.5.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the v4.5, there's no secure erase & trim support.
Instead it supports the sanitize feature.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for the power off notify feature, available in
eMMC 4.5 devices. If the host has support for this feature, then the
mmc core will notify the device by setting the POWER_OFF_NOTIFICATION
byte in the extended csd register with a value of 1 (POWER_ON).
For suspend mode short timeout is used, whereas for the normal poweroff
long timeout is used.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
All the files using printk function for displaying kernel messages
in the mmc driver have been replaced with corresponding macro.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
EXT_CSD[248] includes the default maximum timeout for CMD6.
This field is added at eMMC4.5 Spec. And it can be used for default
timeout except for some operations which don't define the timeout
(i.e. background operation, sanitize, flush cache) in eMMC4.5 Spec.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_request_done() is sometimes called from interrupt or other atomic
context. Mostly all mmc_request_done() does is complete(), however it
contains code to retry on error, which uses ->request(). As the error
path is certainly not performance critical, this may be moved to the
waiting function mmc_wait_for_req_done().
This allows ->request() to use runtime PM get_sync() and guarantee it
is never in an atomic context.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit "mmc: add module param to set fault injection attributes" adds
a module_param to this file. But it is relying on the old implicit
"module.h is everywhere" behaviour, and without the explicit include
of moduleparam.h, the pending module.h split up produces this error:
core/debugfs.c:28:35: error: expected ')' before numeric constant
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
