According to section "Checks on Guest Control Registers, Debug Registers, and
and MSRs" in Intel SDM vol 3C, the following checks are performed on vmentry
of nested guests:
If the "load debug controls" VM-entry control is 1, bits 63:32 in the DR7
field must be 0.
In KVM, GUEST_DR7 is set prior to the vmcs02 VM-entry by kvm_set_dr() and the
latter synthesizes a #GP if any bit in the high dword in the former is set.
Hence this field needs to be checked in software.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the CONFIG_X86_64 condition from the low level non-canonical
helpers to effectively enable non-canonical checks on 32-bit KVM.
Non-canonical checks are performed by hardware if the CPU *supports*
64-bit mode, whether or not the CPU is actually in 64-bit mode is
irrelevant.
For the most part, skipping non-canonical checks on 32-bit KVM is ok-ish
because 32-bit KVM always (hopefully) drops bits 63:32 of whatever value
it's checking before propagating it to hardware, and architecturally,
the expected behavior for the guest is a bit of a grey area since the
vCPU itself doesn't support 64-bit mode. I.e. a 32-bit KVM guest can
observe the missed checks in several paths, e.g. INVVPID and VM-Enter,
but it's debatable whether or not the missed checks constitute a bug
because technically the vCPU doesn't support 64-bit mode.
The primary motivation for enabling the non-canonical checks is defense
in depth. As mentioned above, a guest can trigger a missed check via
INVVPID or VM-Enter. INVVPID is straightforward as it takes a 64-bit
virtual address as part of its 128-bit INVVPID descriptor and fails if
the address is non-canonical, even if INVVPID is executed in 32-bit PM.
Nested VM-Enter is a bit more convoluted as it requires the guest to
write natural width VMCS fields via memory accesses and then VMPTRLD the
VMCS, but it's still possible. In both cases, KVM is saved from a true
bug only because its flows that propagate values to hardware (correctly)
take "unsigned long" parameters and so drop bits 63:32 of the bad value.
Explicitly performing the non-canonical checks makes it less likely that
a bad value will be propagated to hardware, e.g. in the INVVPID case,
if __invvpid() didn't implicitly drop bits 63:32 then KVM would BUG() on
the resulting unexpected INVVPID failure due to hardware rejecting the
non-canonical address.
The only downside to enabling the non-canonical checks is that it adds a
relatively small amount of overhead, but the affected flows are not hot
paths, i.e. the overhead is negligible.
Note, KVM technically could gate the non-canonical checks on 32-bit KVM
with static_cpu_has(X86_FEATURE_LM), but on bare metal that's an even
bigger waste of code for everyone except the 0.00000000000001% of the
population running on Yonah, and nested 32-bit on 64-bit already fudges
things with respect to 64-bit CPU behavior.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
[Also do so in nested_vmx_check_host_state as reported by Krish. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the guest is configured to have SPEC_CTRL but the host does not
(which is a nonsensical configuration but these are not explicitly
forbidden) then a host-initiated MSR write can write vmx->spec_ctrl
(respectively svm->spec_ctrl) and trigger a #GP when KVM tries to
restore the host value of the MSR. Add a more comprehensive check
for valid bits of SPEC_CTRL, covering host CPUID flags and,
since we are at it and it is more correct that way, guest CPUID
flags too.
For AMD, remove the unnecessary is_guest_mode check around setting
the MSR interception bitmap, so that the code looks the same as
for Intel.
Cc: Jim Mattson <jmattson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move bit() to cpuid.h in preparation for incorporating the reverse_cpuid
array in bit() build-time assertions. Opportunistically use the BIT()
macro instead of open-coding the shift.
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ICR and TSCDEADLINE MSRs write cause the main MSRs write vmexits in our
product observation, multicast IPIs are not as common as unicast IPI like
RESCHEDULE_VECTOR and CALL_FUNCTION_SINGLE_VECTOR etc.
This patch introduce a mechanism to handle certain performance-critical
WRMSRs in a very early stage of KVM VMExit handler.
This mechanism is specifically used for accelerating writes to x2APIC ICR
that attempt to send a virtual IPI with physical destination-mode, fixed
delivery-mode and single target. Which was found as one of the main causes
of VMExits for Linux workloads.
The reason this mechanism significantly reduce the latency of such virtual
IPIs is by sending the physical IPI to the target vCPU in a very early stage
of KVM VMExit handler, before host interrupts are enabled and before expensive
operations such as reacquiring KVM’s SRCU lock.
Latency is reduced even more when KVM is able to use APICv posted-interrupt
mechanism (which allows to deliver the virtual IPI directly to target vCPU
without the need to kick it to host).
Testing on Xeon Skylake server:
The virtual IPI latency from sender send to receiver receive reduces
more than 200+ cpu cycles.
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Sean Christopherson <sean.j.christopherson@intel.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert a plethora of parameters and variables in the MMU and page fault
flows from type gva_t to gpa_t to properly handle TDP on 32-bit KVM.
Thanks to PSE and PAE paging, 32-bit kernels can access 64-bit physical
addresses. When TDP is enabled, the fault address is a guest physical
address and thus can be a 64-bit value, even when both KVM and its guest
are using 32-bit virtual addressing, e.g. VMX's VMCS.GUEST_PHYSICAL is a
64-bit field, not a natural width field.
Using a gva_t for the fault address means KVM will incorrectly drop the
upper 32-bits of the GPA. Ditto for gva_to_gpa() when it is used to
translate L2 GPAs to L1 GPAs.
Opportunistically rename variables and parameters to better reflect the
dual address modes, e.g. use "cr2_or_gpa" for fault addresses and plain
"addr" instead of "vaddr" when the address may be either a GVA or an L2
GPA. Similarly, use "gpa" in the nonpaging_page_fault() flows to avoid
a confusing "gpa_t gva" declaration; this also sets the stage for a
future patch to combing nonpaging_page_fault() and tdp_page_fault() with
minimal churn.
Sprinkle in a few comments to document flows where an address is known
to be a GVA and thus can be safely truncated to a 32-bit value. Add
WARNs in kvm_handle_page_fault() and FNAME(gva_to_gpa_nested)() to help
document such cases and detect bugs.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 4b9852f4f3 ("KVM: x86: Fix INIT signal handling in various CPU states")
fixed KVM to also latch pending LAPIC INIT event when vCPU is in VMX
operation.
However, current API of KVM_SET_MP_STATE allows userspace to put vCPU
into KVM_MP_STATE_SIPI_RECEIVED or KVM_MP_STATE_INIT_RECEIVED even when
vCPU is in VMX operation.
Fix this by introducing a util method to check if vCPU state latch INIT
signals and use it in KVM_SET_MP_STATE handler.
Fixes: 4b9852f4f3 ("KVM: x86: Fix INIT signal handling in various CPU states")
Reported-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hoist the vendor-specific code related to loading the hardware IA32_XSS
MSR with guest/host values on VM-entry/VM-exit to common x86 code.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Change-Id: Ic6e3430833955b98eb9b79ae6715cf2a3fdd6d82
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add WARN_ON_ONCE() checks in kvm_register_{read,write}() to detect reg
values that would cause KVM to overflow vcpu->arch.regs. Change the reg
param to an 'int' to make it clear that the reg index is unverified.
Regarding the overhead of WARN_ON_ONCE(), now that all fixed GPR reads
and writes use dedicated accessors, e.g. kvm_rax_read(), the overhead
is limited to flows where the reg index is generated at runtime. And
there is at least one historical bug where KVM has generated an out-of-
bounds access to arch.regs (see commit b68f3cc7d9, "KVM: x86: Always
use 32-bit SMRAM save state for 32-bit kernels").
Adding the WARN_ON_ONCE() protection paves the way for additional
cleanup related to kvm_reg and kvm_reg_ex.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Request triple fault in kvm_inject_realmode_interrupt() instead of
returning EMULATE_FAIL and deferring to the caller. All existing
callers request triple fault and it's highly unlikely Real Mode is
going to acquire new features. While this consolidates a small amount
of code, the real goal is to remove the last reference to EMULATE_FAIL.
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename "access" to "mmio_access" to match the other MMIO cache members
and to make it more obvious that it's tracking the access permissions
for the MMIO cache.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Dedicated instances are currently disturbed by unnecessary jitter due
to the emulated lapic timers firing on the same pCPUs where the
vCPUs reside. There is no hardware virtual timer on Intel for guest
like ARM, so both programming timer in guest and the emulated timer fires
incur vmexits. This patch tries to avoid vmexit when the emulated timer
fires, at least in dedicated instance scenario when nohz_full is enabled.
In that case, the emulated timers can be offload to the nearest busy
housekeeping cpus since APICv has been found for several years in server
processors. The guest timer interrupt can then be injected via posted interrupts,
which are delivered by the housekeeping cpu once the emulated timer fires.
The host should tuned so that vCPUs are placed on isolated physical
processors, and with several pCPUs surplus for busy housekeeping.
If disabled mwait/hlt/pause vmexits keep the vCPUs in non-root mode,
~3% redis performance benefit can be observed on Skylake server, and the
number of external interrupt vmexits drops substantially. Without patch
VM-EXIT Samples Samples% Time% Min Time Max Time Avg time
EXTERNAL_INTERRUPT 42916 49.43% 39.30% 0.47us 106.09us 0.71us ( +- 1.09% )
While with patch:
VM-EXIT Samples Samples% Time% Min Time Max Time Avg time
EXTERNAL_INTERRUPT 6871 9.29% 2.96% 0.44us 57.88us 0.72us ( +- 4.02% )
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Checking for 32-bit PAE is quite common around code that fiddles with
the PDPTRs. Add a function to compress all checks into a single
invocation.
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow guest reads CORE cstate when exposing host CPU power management capabilities
to the guest. PKG cstate is restricted to avoid a guest to get the whole package
information in multi-tenant scenario.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Sean Christopherson <sean.j.christopherson@intel.com>
Cc: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* POWER: support for direct access to the POWER9 XIVE interrupt controller,
memory and performance optimizations.
* x86: support for accessing memory not backed by struct page, fixes and refactoring
* Generic: dirty page tracking improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJc3qV/AAoJEL/70l94x66Dn3QH/jX1Bn0P/RZAIt4w0SySklSg
PqxUKDyBQqB9vN9Qeb9jWXAKPH2CtM3+up/rz7oRnBWp7qA6vXcC/R/QJYAvzdXE
nklsR/oYCsflR1KdlVYuDvvPCPP2fLBU5zfN83OsaBQ8fNRkm3gN+N5XQ2SbXbLy
Mo9tybS4otY201UAC96e8N0ipwwyCRpDneQpLcl+F5nH3RBt63cVbs04O+70MXn7
eT4I+8K3+Go7LATzT8hglD21D/7uvE31qQb6yr5L33IfhU4GB51RZzBXTNaAdY8n
hT1rMrRkAMAFWYZPQDfoMadjWU3i5DIfstKjDxOr9oTfuOEp5Z+GvJwvVnUDg1I=
=D0+p
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- support for SVE and Pointer Authentication in guests
- PMU improvements
POWER:
- support for direct access to the POWER9 XIVE interrupt controller
- memory and performance optimizations
x86:
- support for accessing memory not backed by struct page
- fixes and refactoring
Generic:
- dirty page tracking improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (155 commits)
kvm: fix compilation on aarch64
Revert "KVM: nVMX: Expose RDPMC-exiting only when guest supports PMU"
kvm: x86: Fix L1TF mitigation for shadow MMU
KVM: nVMX: Disable intercept for FS/GS base MSRs in vmcs02 when possible
KVM: PPC: Book3S: Remove useless checks in 'release' method of KVM device
KVM: PPC: Book3S HV: XIVE: Fix spelling mistake "acessing" -> "accessing"
KVM: PPC: Book3S HV: Make sure to load LPID for radix VCPUs
kvm: nVMX: Set nested_run_pending in vmx_set_nested_state after checks complete
tests: kvm: Add tests for KVM_SET_NESTED_STATE
KVM: nVMX: KVM_SET_NESTED_STATE - Tear down old EVMCS state before setting new state
tests: kvm: Add tests for KVM_CAP_MAX_VCPUS and KVM_CAP_MAX_CPU_ID
tests: kvm: Add tests to .gitignore
KVM: Introduce KVM_CAP_MANUAL_DIRTY_LOG_PROTECT2
KVM: Fix kvm_clear_dirty_log_protect off-by-(minus-)one
KVM: Fix the bitmap range to copy during clear dirty
KVM: arm64: Fix ptrauth ID register masking logic
KVM: x86: use direct accessors for RIP and RSP
KVM: VMX: Use accessors for GPRs outside of dedicated caching logic
KVM: x86: Omit caching logic for always-available GPRs
kvm, x86: Properly check whether a pfn is an MMIO or not
...
Automatically adjusting the globally-shared timer advancement could
corrupt the timer, e.g. if multiple vCPUs are concurrently adjusting
the advancement value. That could be partially fixed by using a local
variable for the arithmetic, but it would still be susceptible to a
race when setting timer_advance_adjust_done.
And because virtual_tsc_khz and tsc_scaling_ratio are per-vCPU, the
correct calibration for a given vCPU may not apply to all vCPUs.
Furthermore, lapic_timer_advance_ns is marked __read_mostly, which is
effectively violated when finding a stable advancement takes an extended
amount of timer.
Opportunistically change the definition of lapic_timer_advance_ns to
a u32 so that it matches the style of struct kvm_timer. Explicitly
pass the param to kvm_create_lapic() so that it doesn't have to be
exposed to lapic.c, thus reducing the probability of unintentionally
using the global value instead of the per-vCPU value.
Cc: Liran Alon <liran.alon@oracle.com>
Cc: Wanpeng Li <wanpengli@tencent.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Cc: stable@vger.kernel.org
Fixes: 3b8a5df6c4 ("KVM: LAPIC: Tune lapic_timer_advance_ns automatically")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This check will soon be done on every nested vmentry and vmexit,
"parallelize" it using bitwise operations.
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
guest xcr0 could leak into host when MCE happens in guest mode. Because
do_machine_check() could schedule out at a few places.
For example:
kvm_load_guest_xcr0
...
kvm_x86_ops->run(vcpu) {
vmx_vcpu_run
vmx_complete_atomic_exit
kvm_machine_check
do_machine_check
do_memory_failure
memory_failure
lock_page
In this case, host_xcr0 is 0x2ff, guest vcpu xcr0 is 0xff. After schedule
out, host cpu has guest xcr0 loaded (0xff).
In __switch_to {
switch_fpu_finish
copy_kernel_to_fpregs
XRSTORS
If any bit i in XSTATE_BV[i] == 1 and xcr0[i] == 0, XRSTORS will
generate #GP (In this case, bit 9). Then ex_handler_fprestore kicks in
and tries to reinitialize fpu by restoring init fpu state. Same story as
last #GP, except we get DOUBLE FAULT this time.
Cc: stable@vger.kernel.org
Signed-off-by: WANG Chao <chao.wang@ucloud.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM uses bit 0 of the memslots generation as an "update in-progress"
flag, which is used by x86 to prevent caching MMIO access while the
memslots are changing. Although the intended behavior is flag-like,
e.g. MMIO sptes intentionally drop the in-progress bit so as to avoid
caching data from in-flux memslots, the implementation oftentimes treats
the bit as part of the generation number itself, e.g. incrementing the
generation increments twice, once to set the flag and once to clear it.
Prior to commit 4bd518f159 ("KVM: use separate generations for
each address space"), incorporating the "update in-progress" bit into
the generation number largely made sense, e.g. "real" generations are
even, "bogus" generations are odd, most code doesn't need to be aware of
the bit, etc...
Now that unique memslots generation numbers are assigned to each address
space, stealthing the in-progress status into the generation number
results in a wide variety of subtle code, e.g. kvm_create_vm() jumps
over bit 0 when initializing the memslots generation without any hint as
to why.
Explicitly define the flag and convert as much code as possible (which
isn't much) to actually treat it like a flag. This paves the way for
eventually using a different bit for "update in-progress" so that it can
be a flag in truth instead of a awkward extension to the generation
number.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When installing new memslots, KVM sets bit 0 of the generation number to
indicate that an update is in-progress. Until the update is complete,
there are no guarantees as to whether a vCPU will see the old or the new
memslots. Explicity prevent caching MMIO accesses so as to avoid using
an access cached from the old memslots after the new memslots have been
installed.
Note that it is unclear whether or not disabling caching during the
update window is strictly necessary as there is no definitive
documentation as to what ordering guarantees KVM provides with respect
to updating memslots. That being said, the MMIO spte code does not
allow reusing sptes created while an update is in-progress, and the
associated documentation explicitly states:
We do not want to use an MMIO sptes created with an odd generation
number, ... If KVM is unlucky and creates an MMIO spte while the
low bit is 1, the next access to the spte will always be a cache miss.
At the very least, disabling the per-vCPU MMIO cache during updates will
make its behavior consistent with the MMIO spte behavior and
documentation.
Fixes: 56f17dd3fb ("kvm: x86: fix stale mmio cache bug")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When exception payloads are enabled by userspace (which is not yet
possible) and a #PF is raised in L2, defer the setting of CR2 until
the #PF is delivered. This allows the L1 hypervisor to intercept the
fault before CR2 is modified.
For backwards compatibility, when exception payloads are not enabled
by userspace, kvm_multiple_exception modifies CR2 when the #PF
exception is raised.
Reported-by: Jim Mattson <jmattson@google.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allowing x86_emulate_instruction() to be called directly has led to
subtle bugs being introduced, e.g. not setting EMULTYPE_NO_REEXECUTE
in the emulation type. While most of the blame lies on re-execute
being opt-out, exporting x86_emulate_instruction() also exposes its
cr2 parameter, which may have contributed to commit d391f12070
("x86/kvm/vmx: do not use vm-exit instruction length for fast MMIO
when running nested") using x86_emulate_instruction() instead of
emulate_instruction() because "hey, I have a cr2!", which in turn
introduced its EMULTYPE_NO_REEXECUTE bug.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
This patch extends the checks done prior to a nested VM entry.
Specifically, it extends the check_vmentry_prereqs function with checks
for fields relevant to the VM-entry event injection information, as
described in the Intel SDM, volume 3.
This patch is motivated by a syzkaller bug, where a bad VM-entry
interruption information field is generated in the VMCS02, which causes
the nested VM launch to fail. Then, KVM fails to resume L1.
While KVM should be improved to correctly resume L1 execution after a
failed nested launch, this change is justified because the existing code
to resume L1 is flaky/ad-hoc and the test coverage for resuming L1 is
sparse.
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Marc Orr <marcorr@google.com>
[Removed comment whose parts were describing previous revisions and the
rest was obvious from function/variable naming. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Int the next patch the emulator's .read_std and .write_std callbacks will
grow another argument, which is not needed in kvm_read_guest_virt and
kvm_write_guest_virt_system's callers. Since we have to make separate
functions, let's give the currently existing names a nicer interface, too.
Fixes: 129a72a0d3 ("KVM: x86: Introduce segmented_write_std", 2017-01-12)
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move DISABLE_EXITS KVM capability bits to the UAPI just like the rest of
capabilities.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: x86@kernel.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Introduce handle_ud() to handle invalid opcode, this function will be
used by later patches.
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Andrew Cooper <andrew.cooper3@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For exceptions & NMIs events, KVM code use the following
coding convention:
*) "pending" represents an event that should be injected to guest at
some point but it's side-effects have not yet occurred.
*) "injected" represents an event that it's side-effects have already
occurred.
However, interrupts don't conform to this coding convention.
All current code flows mark interrupt.pending when it's side-effects
have already taken place (For example, bit moved from LAPIC IRR to
ISR). Therefore, it makes sense to just rename
interrupt.pending to interrupt.injected.
This change follows logic of previous commit 664f8e26b0 ("KVM: X86:
Fix loss of exception which has not yet been injected") which changed
exception to follow this coding convention as well.
It is important to note that in case !lapic_in_kernel(vcpu),
interrupt.pending usage was and still incorrect.
In this case, interrrupt.pending can only be set using one of the
following ioctls: KVM_INTERRUPT, KVM_SET_VCPU_EVENTS and
KVM_SET_SREGS. Looking at how QEMU uses these ioctls, one can see that
QEMU uses them either to re-set an "interrupt.pending" state it has
received from KVM (via KVM_GET_VCPU_EVENTS interrupt.pending or
via KVM_GET_SREGS interrupt_bitmap) or by dispatching a new interrupt
from QEMU's emulated LAPIC which reset bit in IRR and set bit in ISR
before sending ioctl to KVM. So it seems that indeed "interrupt.pending"
in this case is also suppose to represent "interrupt.injected".
However, kvm_cpu_has_interrupt() & kvm_cpu_has_injectable_intr()
is misusing (now named) interrupt.injected in order to return if
there is a pending interrupt.
This leads to nVMX/nSVM not be able to distinguish if it should exit
from L2 to L1 on EXTERNAL_INTERRUPT on pending interrupt or should
re-inject an injected interrupt.
Therefore, add a FIXME at these functions for handling this issue.
This patch introduce no semantics change.
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Bring the PLE(pause loop exit) logic to AMD svm driver.
While testing, we found this helping in situations where numerous
pauses are generated. Without these patches we could see continuos
VMEXITS due to pause interceptions. Tested it on AMD EPYC server with
boot parameter idle=poll on a VM with 32 vcpus to simulate extensive
pause behaviour. Here are VMEXITS in 10 seconds interval.
Pauses 810199 504
Total 882184 325415
Signed-off-by: Babu Moger <babu.moger@amd.com>
[Prevented the window from dropping below the initial value. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
This patch brings some of the code from vmx to x86.h header file. Now, we
can share this code between vmx and svm. Modified couple functions to make
it common.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
KVM and perf have a special backdoor mechanism to report the IP for interrupts
re-executed after vm exit. This works for the NMIs that perf normally uses.
However when perf is in timer mode it doesn't work because the timer interrupt
doesn't get this special treatment. This is common when KVM is running
nested in another hypervisor which may not implement the PMU, so only
timer mode is available.
Call the functions to set up the backdoor IP also for non NMI interrupts.
I renamed the functions to set up the backdoor IP reporting to be more
appropiate for their new use. The SVM change is only compile tested.
v2: Moved the functions inline.
For the normal interrupt case the before/after functions are now
called from x86.c, not arch specific code.
For the NMI case we still need to call it in the architecture
specific code, because it's already needed in the low level *_run
functions.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
[Removed unnecessary calls from arch handle_external_intr. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Allow to disable pause loop exit/pause filtering on a per VM basis.
If some VMs have dedicated host CPUs, they won't be negatively affected
due to needlessly intercepted PAUSE instructions.
Thanks to Jan H. Schönherr's initial patch.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If host CPUs are dedicated to a VM, we can avoid VM exits on HLT.
This patch adds the per-VM capability to disable them.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allowing a guest to execute MWAIT without interception enables a guest
to put a (physical) CPU into a power saving state, where it takes
longer to return from than what may be desired by the host.
Don't give a guest that power over a host by default. (Especially,
since nothing prevents a guest from using MWAIT even when it is not
advertised via CPUID.)
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Support access to VMware backdoor requires KVM to intercept #GP
exceptions from guest which introduce slight performance hit.
Therefore, control this support by module parameter.
Note that module parameter is exported as it should be consumed by
kvm_intel & kvm_amd to determine if they should intercept #GP or not.
This commit doesn't change semantics.
It is done as a preparation for future commits.
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_clear_exception_queue() should clear pending exception.
This also includes exceptions which were only marked pending but not
yet injected. This is because exception.pending is used for both L1
and L2 to determine if an exception should be raised to guest.
Note that an exception which is pending but not yet injected will
be raised again once the guest will be resumed.
Consider the following scenario:
1) L0 KVM with ignore_msrs=false.
2) L1 prepare vmcs12 with the following:
a) No intercepts on MSR (MSR_BITMAP exist and is filled with 0).
b) No intercept for #GP.
c) vmx-preemption-timer is configured.
3) L1 enters into L2.
4) L2 reads an unhandled MSR that exists in MSR_BITMAP
(such as 0x1fff).
L2 RDMSR could be handled as described below:
1) L2 exits to L0 on RDMSR and calls handle_rdmsr().
2) handle_rdmsr() calls kvm_inject_gp() which sets
KVM_REQ_EVENT, exception.pending=true and exception.injected=false.
3) vcpu_enter_guest() consumes KVM_REQ_EVENT and calls
inject_pending_event() which calls vmx_check_nested_events()
which sees that exception.pending=true but
nested_vmx_check_exception() returns 0 and therefore does nothing at
this point. However let's assume it later sees vmx-preemption-timer
expired and therefore exits from L2 to L1 by calling
nested_vmx_vmexit().
4) nested_vmx_vmexit() calls prepare_vmcs12()
which calls vmcs12_save_pending_event() but it does nothing as
exception.injected is false. Also prepare_vmcs12() calls
kvm_clear_exception_queue() which does nothing as
exception.injected is already false.
5) We now return from vmx_check_nested_events() with 0 while still
having exception.pending=true!
6) Therefore inject_pending_event() continues
and we inject L2 exception to L1!...
This commit will fix above issue by changing step (4) to
clear exception.pending in kvm_clear_exception_queue().
Fixes: 664f8e26b0 ("KVM: X86: Fix loss of exception which has not yet been injected")
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
If Intel/AMD implements MWAIT, we expect that it works well and only
reject known bugs; no reason to do it the other way around for minor
vendors. (Not that they are relevant ATM.)
This allows further simplification of kvm_mwait_in_guest().
And use boot_cpu_has() instead of "cpu_has(&boot_cpu_data," while at it.
Reviewed-by: Alexander Graf <agraf@suse.de>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The check was added in some iteration while trying to fix a reported OS
X on Core 2 bug, but that bug is elsewhere.
The comment is misleading because the guest can call MWAIT with ECX = 0
even if we enforce CPUID5_ECX_INTERRUPT_BREAK; the call would have the
exactly the same effect as if the host didn't have the feature.
A problem is that a QEMU feature exposes CPUID5_ECX_INTERRUPT_BREAK on
CPUs that do not support it. Removing the check changes behavior on
last Pentium 4 lines (Presler, Dempsey, and Tulsa, which had VMX and
MONITOR while missing INTERRUPT_BREAK) when running a guest OS that uses
MWAIT without checking for its presence (QEMU doesn't expose MONITOR).
The only known OS that ignores the MONITOR flag is old Mac OS X and we
allowed it to bug on Core 2 (MWAIT used to throw #UD and only that OS
noticed), so we can save another 20 lines letting it bug on even older
CPUs. Alternatively, we can return MWAIT exiting by default and let
userspace toggle it.
Reviewed-by: Alexander Graf <agraf@suse.de>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The bug prevents MWAIT from waking up after a write to the monitored
cache line.
KVM might emulate a CPU model that shouldn't have the bug, so the guest
would not employ a workaround and possibly miss wakeups.
Better to avoid the situation.
Reviewed-by: Alexander Graf <agraf@suse.de>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vmx_complete_interrupts() assumes that the exception is always injected,
so it can be dropped by kvm_clear_exception_queue(). However,
an exception cannot be injected immediately if it is: 1) originally
destined to a nested guest; 2) trapped to cause a vmexit; 3) happening
right after VMLAUNCH/VMRESUME, i.e. when nested_run_pending is true.
This patch applies to exceptions the same algorithm that is used for
NMIs, replacing exception.reinject with "exception.injected" (equivalent
to nmi_injected).
exception.pending now represents an exception that is queued and whose
side effects (e.g., update RFLAGS.RF or DR7) have not been applied yet.
If exception.pending is true, the exception might result in a nested
vmexit instead, too (in which case the side effects must not be applied).
exception.injected instead represents an exception that is going to be
injected into the guest at the next vmentry.
Reported-by: Radim Krčmář <rkrcmar@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch exposes 5 level page table feature to the VM.
At the same time, the canonical virtual address checking is
extended to support both 48-bits and 57-bits address width.
Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Extends the shadow paging code, so that 5 level shadow page
table can be constructed if VM is running in 5 level paging
mode.
Also extends the ept code, so that 5 level ept table can be
constructed if maxphysaddr of VM exceeds 48 bits. Unlike the
shadow logic, KVM should still use 4 level ept table for a VM
whose physical address width is less than 48 bits, even when
the VM is running in 5 level paging mode.
Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com>
[Unconditionally reset the MMU context in kvm_cpuid_update.
Changing MAXPHYADDR invalidates the reserved bit bitmasks.
- Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is currently some confusion between nested and L1 GPAs. The
assignment to "direct" in kvm_mmu_page_fault tries to fix that, but
it is not enough. What this patch does is fence off the MMIO cache
completely when using shadow nested page tables, since we have neither
a GVA nor an L1 GPA to put in the cache. This also allows some
simplifications in kvm_mmu_page_fault and FNAME(page_fault).
The EPT misconfig likewise does not have an L1 GPA to pass to
kvm_io_bus_write, so that must be skipped for guest mode.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[Changed comment to say "GPAs" instead of "L1's physical addresses", as
per David's review. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Guests that are heavy on futexes end up IPI'ing each other a lot. That
can lead to significant slowdowns and latency increase for those guests
when running within KVM.
If only a single guest is needed on a host, we have a lot of spare host
CPU time we can throw at the problem. Modern CPUs implement a feature
called "MWAIT" which allows guests to wake up sleeping remote CPUs without
an IPI - thus without an exit - at the expense of never going out of guest
context.
The decision whether this is something sensible to use should be up to the
VM admin, so to user space. We can however allow MWAIT execution on systems
that support it properly hardware wise.
This patch adds a CAP to user space and a KVM cpuid leaf to indicate
availability of native MWAIT execution. With that enabled, the worst a
guest can do is waste as many cycles as a "jmp ." would do, so it's not
a privilege problem.
We consciously do *not* expose the feature in our CPUID bitmap, as most
people will want to benefit from sleeping vCPUs to allow for over commit.
Reported-by: "Gabriel L. Somlo" <gsomlo@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
[agraf: fix amd, change commit message]
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce a function that reads the exact nanoseconds value that is
provided to the guest in kvmclock. This crystallizes the notion of
kvmclock as a thin veneer over a stable TSC, that the guest will
(hopefully) convert with NTP. In other words, kvmclock is *not* a
paravirtualized host-to-guest NTP.
Drop the get_kernel_ns() function, that was used both to get the base
value of the master clock and to get the current value of kvmclock.
The former use is replaced by ktime_get_boot_ns(), the latter is
the purpose of get_kernel_ns().
This also allows KVM to provide a Hyper-V time reference counter that
is synchronized with the time that is computed from the TSC page.
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the inline function nsec_to_cycles from x86.c to x86.h, as
the next patch uses it from lapic.c.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds pkeys support for xsave state.
Signed-off-by: Huaitong Han <huaitong.han@intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use vector-hashing to deliver lowest-priority interrupts, As an
example, modern Intel CPUs in server platform use this method to
handle lowest-priority interrupts.
Signed-off-by: Feng Wu <feng.wu@intel.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is similar to the existing div_frac function, but it returns the
remainder too. Unlike div_frac, it can be used to implement long
division, e.g. (a << 64) / b for 32-bit a and b.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are two concepts that have some confusing naming:
1. Extended State Component numbers (currently called
XFEATURE_BIT_*)
2. Extended State Component masks (currently called XSTATE_*)
The numbers are (currently) from 0-9. State component 3 is the
bounds registers for MPX, for instance.
But when we want to enable "state component 3", we go set a bit
in XCR0. The bit we set is 1<<3. We can check to see if a
state component feature is enabled by looking at its bit.
The current 'xfeature_bit's are at best xfeature bit _numbers_.
Calling them bits is at best inconsistent with ending the enum
list with 'XFEATURES_NR_MAX'.
This patch renames the enum to be 'xfeature'. These also
happen to be what the Intel documentation calls a "state
component".
We also want to differentiate these from the "XSTATE_*" macros.
The "XSTATE_*" macros are a mask, and we rename them to match.
These macros are reasonably widely used so this patch is a
wee bit big, but this really is just a rename.
The only non-mechanical part of this is the
s/XSTATE_EXTEND_MASK/XFEATURE_MASK_EXTEND/
We need a better name for it, but that's another patch.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: dave@sr71.net
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/20150902233126.38653250@viggo.jf.intel.com
[ Ported to v4.3-rc1. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
