Currently almost each platform driver uses its own resets and clocks
naming in order to get the corresponding descriptors. It makes the code
harder to maintain and comprehend especially seeing the DWC PCIe core main
resets and clocks signals set hasn't changed much for about at least one
major IP-core release. So in order to organize things around these signals
we suggest to create a generic interface for them in accordance with the
naming introduced in the DWC PCIe IP-core reference manual:
Application clocks:
- "dbi" - data bus interface clock (on some DWC PCIe platforms it's
referred as "pclk", "pcie", "sys", "ahb", "cfg", "iface",
"gio", "reg", "pcie_apb_sys");
- "mstr" - AXI-bus master interface clock (some DWC PCIe glue drivers
refer to this clock as "port", "bus", "pcie_bus",
"bus_master/master_bus/axi_m", "pcie_aclk");
- "slv" - AXI-bus slave interface clock (also called as "port", "bus",
"pcie_bus", "bus_slave/slave_bus/axi_s", "pcie_aclk",
"pcie_inbound_axi").
Core clocks:
- "pipe" - core-PCS PIPE interface clock coming from external PHY (it's
normally named by the platform drivers as just "pipe");
- "core" - primary clock of the controller (none of the platform drivers
declare such a clock but in accordance with the ref. manual
the devices may have it separately specified);
- "aux" - auxiliary PMC domain clock (it is named by some platforms as
"pcie_aux" and just "aux");
- "ref" - Generic reference clock (it is a generic clock source, which
can be used as a signal source for multiple interfaces, some
platforms call it as "ref", "general", "pcie_phy",
"pcie_phy_ref").
Application resets:
- "dbi" - Data-bus interface reset (it's CSR interface clock and is
normally called as "apb" though technically it's not APB but
DWC PCIe-specific interface);
- "mstr" - AXI-bus master reset (some platforms call it as "port", "apps",
"bus", "axi_m");
- "slv" - ABI-bus slave reset (some platforms call it as "port", "apps",
"bus", "axi_s").
Core resets:
- "non-sticky" - non-sticky CSR flags reset;
- "sticky" - sticky CSR flags reset;
- "pipe" - PIPE-interface (Core-PCS) logic reset (some platforms
call it just "pipe");
- "core" - controller primary reset (resets everything except PMC
module, some platforms refer to this signal as "soft",
"pci");
- "phy" - PCS/PHY block reset (strictly speaking it is normally
connected to the input of an external block, but the
reference manual says it must be available for the PMC
working correctly, some existing platforms call it
"pciephy", "phy", "link");
- "hot" - PMC hot reset signal (also called as "sleep");
- "pwr" - cold reset signal (can be referred as "pwr", "turnoff").
Bus reset:
- "perst" - PCIe standard signal used to reset the PCIe peripheral
devices.
As you can see each platform uses it's own naming for basically the same
set of the signals. In the framework of this commit we suggest to add a
set of the clocks and reset signals resources, corresponding names and
identifiers for each denoted entity. At current stage the platforms will
be able to use the provided infrastructure to automatically request all
these resources and manipulate with them in the Host/EP init callbacks.
Alas it isn't that easy to create a common cold/hot reset procedure due to
too many platform-specifics in the procedure, like the external flags
exposure and the delays requirement.
Link: https://lore.kernel.org/r/20221113191301.5526-20-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Since the iATU CSR region is now retrieved in the DW PCIe resources getter
there is no much benefits in the iATU detection procedures splitting up.
Therefore let's join the iATU unroll/viewport detection procedure with the
rest of the iATU parameters detection code. The resultant method will be
as coherent as before, while the redundant functions will be eliminated
thus producing more readable code.
Link: https://lore.kernel.org/r/20221113191301.5526-19-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently the DW PCIe Root Port and Endpoint CSR spaces are retrieved in
the separate parts of the DW PCIe core driver. It doesn't really make
sense since the both controller types have identical set of the core CSR
regions: DBI, DBI CS2 and iATU/eDMA. Thus we can simplify the DW PCIe Host
and EP initialization methods by moving the platform-specific registers
space getting and mapping into a common method. It gets to be even more
justified seeing the CSRs base address pointers are preserved in the
common DW PCIe descriptor. Note all the OF-based common DW PCIe settings
initialization will be moved to the new method too in order to have a
single function for all the generic platform properties handling in single
place.
A nice side-effect of this change is that the pcie-designware-host.c and
pcie-designware-ep.c drivers are cleaned up from all the direct dw_pcie
storage modification, which makes the DW PCIe core, Root Port and Endpoint
modules more coherent.
Link: https://lore.kernel.org/r/20221113191301.5526-18-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Since in addition to the already available iATU unrolled mapping we are
about to add a few more DW PCIe platform-specific capabilities (CDM-check
and generic clocks/resets resources) let's add a generic interface to set
and get the flags indicating their availability. The new interface shall
improve maintainability of the platform-specific code.
Link: https://lore.kernel.org/r/20221113191301.5526-17-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In accordance with the generic PCIe Root Port DT-bindings the "dma-ranges"
property has the same format as the "ranges" property. The only difference
is in their semantics. The "dma-ranges" property describes the PCIe-to-CPU
memory mapping in opposite to the CPU-to-PCIe mapping of the "ranges"
property. Even though the DW PCIe controllers are normally equipped with
the internal Address Translation Unit which inbound and outbound tables
can be used to implement both properties semantics, it was surprising for
me to discover that the host-related part of the DW PCIe driver currently
supports the "ranges" property only while the "dma-ranges" windows are
just ignored. Having the "dma-ranges" supported in the driver would be
very handy for the platforms, that don't tolerate the 1:1 CPU-PCIe memory
mapping and require a customized PCIe memory layout. So let's fix that by
introducing the "dma-ranges" property support.
First of all we suggest to rename the dw_pcie_prog_inbound_atu() method to
dw_pcie_prog_ep_inbound_atu() and create a new version of the
dw_pcie_prog_inbound_atu() function. Thus we'll have two methods for the
RC and EP controllers respectively in the same way as it has been
developed for the outbound ATU setup methods.
Secondly aside with the memory window index and type the new
dw_pcie_prog_inbound_atu() function will accept CPU address, PCIe address
and size as its arguments. These parameters define the PCIe and CPU memory
ranges which will be used to setup the respective inbound ATU mapping. The
passed parameters need to be verified against the ATU ranges constraints
in the same way as it is done for the outbound ranges.
Finally the DMA-ranges detected for the PCIe controller need to be
converted to the inbound ATU entries during the host controller
initialization procedure. It will be done in the framework of the
dw_pcie_iatu_setup() method. Note before setting the inbound ranges up we
need to disable all the inbound ATU entries in order to prevent unexpected
PCIe TLPs translations defined by some third party software like
bootloaders.
Link: https://lore.kernel.org/r/20221113191301.5526-16-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This patch switches the driver away from legacy gpio/of_gpio API to
gpiod API, and removes use of of_get_named_gpio_flags() which I want to
make private to gpiolib.
Link: https://lore.kernel.org/r/20220906204301.3736813-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
When the PHY is the reference clock provider then it must be initialized
and powered on before the reset on the client is deasserted, otherwise
the link will never come up. The order was changed in cf236e0c0d.
Restore the correct order to make the driver work again on boards where
the PHY provides the reference clock. This also changes the order for
boards where the Soc is the PHY reference clock divider, but this
shouldn't do any harm.
Link: https://lore.kernel.org/r/20221101095714.440001-1-s.hauer@pengutronix.de
Fixes: cf236e0c0d ("PCI: imx6: Do not hide PHY driver callbacks and refine the error handling")
Tested-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Some of the platforms (like Tegra194 and Tegra234) have open slots and
not having an endpoint connected to the slot is not an error.
So, changing the macro from dev_err to dev_info to log the event.
Link: https://lore.kernel.org/r/20220913101237.4337-1-vidyas@nvidia.com
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Dual mode DesignWare PCIe IP has PTM capability enabled (if supported) even
in the EP mode. The PCIe compliance for the EP mode expects PTM
capabilities (ROOT_CAPABLE, RES_CAPABLE, CLK_GRAN) be disabled.
Hence disable PTM for the EP mode.
Link: https://lore.kernel.org/r/20220919143340.4527-3-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
commit aeaa0bfe89 ("PCI: dwc: Move N_FTS setup to common setup")
incorrectly uses pci->link_gen in deriving the index to the
n_fts[] array also introducing the issue of accessing beyond the
boundaries of array for greater than Gen-2 speeds. This change fixes
that issue.
Link: https://lore.kernel.org/r/20220926111923.22487-1-vidyas@nvidia.com
Fixes: aeaa0bfe89 ("PCI: dwc: Move N_FTS setup to common setup")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmNKzlUUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vxBbA//QYuw8iZHzshJntCyWlTRg742x2jI
2NrLojVG/ccSlqnl/KRultaPFdSlZb221UASt7CAEIGoP6+/SNepazEEJ4QJhMX6
inY/hYrVd2OHhCnO+OoNd7DKfbeJRkFVMHOGJdpbQ7jMwa99YSaN6xEMfALcZIrg
8CqYKDpdJW4avYyKlfXayY42d8gljWJwfLuK1xEnnIrdvXQEB3vj3yKxziadhBtA
EJbLWORVF+yQwq63NCPkLvCe0ZuV09a4q4IhlzWo+30FLMOsk2z4HBi1B2fwlawV
tnYCt0i6FNC6e3DJyWX/hkAiIbJUadnych+LcGq+/FY30tCBtNkNaQN3XsrvdvI4
5piacj1av21R7JHSyk64M4jdNlE7MYonQNsc8vp4yDtlAjQYkaj7BJdsIq3MCTei
ce6mxguVb2hrMr4fZXc8ka7XZkofJNv/XhfuQAorzKfEqA8cI4enICsPdoTFyZDV
pYYuHIJXY4rTm0wUD+TlDg/Cn6gyLu3WYVyEn6q/E53Twj1rr5ske7igDMDVYYly
qMg8CTPHYzHJ0wbzkf0CfND7SVAAE1BnIzr4Drfbrm+fi11HVhd0u/0XiWf2NthW
/ZFQUDBh0SwSHgUnO+ONqcR3arhIT4PEsEJadD4kuW4nIyPS7t1Nfu0V3XUZDa14
U6UeL6URnXBDV7U=
=gs3v
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.1-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci fix from Bjorn Helgaas:
"Revert the attempt to distribute spare resources to unconfigured
hotplug bridges at boot time.
This fixed some dock hot-add scenarios, but Jonathan Cameron reported
that it broke a topology with a multi-function device where one
function was a Switch Upstream Port and the other was an Endpoint"
* tag 'pci-v6.1-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: Distribute available resources for root buses, too"
This reverts commit e96e27fc6f.
Jonathan reported that this commit broke this topology, where all the space
available on bus 02 was assigned to the 02:00.0 bridge window, leaving none
for the e1000 device at 02:00.1:
pci 0000:00:04.0: bridge window [mem 0x10200000-0x103fffff] to [bus 02-04]
pci 0000:02:00.0: bridge window [mem 0x10200000-0x103fffff] to [bus 03-04]
pci 0000:02:00.1: BAR 0: failed to assign [mem size 0x00020000]
e1000 0000:02:00.1: can't ioremap BAR 0: [??? 0x00000000 flags 0x0]
Link: https://lore.kernel.org/r/20221014124553.0000696f@huawei.com
Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCY0ZjFAAKCRCAXGG7T9hj
vjEsAP4rFMnqc6AXy4Mpvv8cxBtEuQZbwEqgBrMJUvK1jZQrBQD/dOJK2GBCVcfD
2yaVlefFiJGTw5WUlbPeohUlTZ8pJwg=
=xsHV
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.1-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- Some minor typo fixes
- A fix of the Xen pcifront driver for supporting the device model to
run in a Linux stub domain
- A cleanup of the pcifront driver
- A series to enable grant-based virtio with Xen on x86
- A cleanup of Xen PV guests to distinguish between safe and faulting
MSR accesses
- Two fixes of the Xen gntdev driver
- Two fixes of the new xen grant DMA driver
* tag 'for-linus-6.1-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Kconfig: Fix spelling mistake "Maxmium" -> "Maximum"
xen/pv: support selecting safe/unsafe msr accesses
xen/pv: refactor msr access functions to support safe and unsafe accesses
xen/pv: fix vendor checks for pmu emulation
xen/pv: add fault recovery control to pmu msr accesses
xen/virtio: enable grant based virtio on x86
xen/virtio: use dom0 as default backend for CONFIG_XEN_VIRTIO_FORCE_GRANT
xen/virtio: restructure xen grant dma setup
xen/pcifront: move xenstore config scanning into sub-function
xen/gntdev: Accommodate VMA splitting
xen/gntdev: Prevent leaking grants
xen/virtio: Fix potential deadlock when accessing xen_grant_dma_devices
xen/virtio: Fix n_pages calculation in xen_grant_dma_map(unmap)_page()
xen/xenbus: Fix spelling mistake "hardward" -> "hardware"
xen-pcifront: Handle missed Connected state
-----BEGIN PGP SIGNATURE-----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=pOqY
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Resource management:
- Distribute spare resources to unconfigured hotplug bridges at
boot-time (not just when hot-adding such a bridge), which makes
hot-adding devices to docks work better.
- Revert to a BAR assignment inherited from firmware only when the
address is actually reachable via any upstream bridges, which fixes
some cases where firmware doesn't configure all devices.
- Add a sysfs interface to resize BARs so this can be done before
assigning devices to a VM through VFIO.
Power management:
- Disable Precision Time Management for all devices on suspend to
enable lower-power PM state. We previously did this just for Root
Ports, which isn't enough because downstream devices can still
generate PTM messages, which cause errors if it's disabled in the
Root Port.
- Save and restore the ASPM L1 PM Substates configuration for
suspend/ resume. Previously this configuration was lost, so L1.x
states likely stopped working after resume.
- Check whether the L1 PM Substates Capability exists. If it didn't
exist, we previously read junk and tried to configure L1 Substates
based on that.
- Fix the LTR_L1.2_THRESHOLD computation, which previously set a
threshold for entering L1.2 that was too low in some cases.
- Reduce the delay after transitions to or from D3cold by using
usleep_range() rather than msleep(), which often slept for ~19ms
instead of the 10ms normally required. The spec says 10ms is
enough, but it's possible we could trip over devices that need a
little more.
Error handling:
- Work around a BIOS bug that caused Intel Root Ports to advertise a
Root Port Programmed I/O (RP PIO) log size of zero, which caused
annoying warnings and prevented the kernel from dumping log
registers for DPC errors.
Qualcomm PCIe controller driver:
- Add support for SC8280XP and SA8540P host controllers and SM8450
endpoint controller.
- Disable Master AXI clock on endpoint controllers to save power when
link is idle or in L1.x.
- Expose link state transition counts via debugfs to help debug
issues with low-power states.
- Add auto-loading module support.
Synopsys DesignWare PCIe controller driver:
- Remove a dependency on ZONE_DMA32 by allocating the MSI target page
differently. There's more work to do related to eDMA controllers,
so it's not completely settled"
* tag 'pci-v6.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (71 commits)
PCI: qcom-ep: Check platform_get_resource_byname() return value
PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Define clocks per platform
PCI: qcom-ep: Make PERST separation optional
dt-bindings: PCI: qcom-ep: Make PERST separation optional
PCI: qcom-ep: Disable Master AXI Clock when there is no PCIe traffic
PCI: Expose PCIe Resizable BAR support via sysfs
PCI/ASPM: Correct LTR_L1.2_THRESHOLD computation
PCI/ASPM: Ignore L1 PM Substates if device lacks capability
PCI/ASPM: Factor out L1 PM Substates configuration
PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SS
PCI: qcom-ep: Expose link transition counts via debugfs
PCI: qcom-ep: Disable IRQs during driver remove
PCI/ASPM: Save L1 PM Substates Capability for suspend/resume
PCI/ASPM: Refactor L1 PM Substates Control Register programming
PCI: qcom-ep: Make use of the cached dev pointer
PCI: qcom-ep: Rely on the clocks supplied by devicetree
PCI: qcom-ep: Add kernel-doc for qcom_pcie_ep structure
phy: freescale: imx8m-pcie: Fix the wrong order of phy_init() and phy_power_on()
...
pcifront_try_connect() and pcifront_attach_devices() share a large
chunk of duplicated code for reading the config information from
Xenstore, which only differs regarding calling pcifront_rescan_root()
or pcifront_scan_root().
Put that code into a new sub-function. It is fine to always call
pcifront_rescan_root() from that common function, as it will fallback
to pcifront_scan_root() if the domain/bus combination isn't known
yet (and pcifront_scan_root() should never be called for an already
known domain/bus combination anyway). In order to avoid duplicate
messages for the fallback case move the check for domain/bus not known
to the beginning of pcifront_rescan_root().
While at it fix the error reporting in case the root-xx node had the
wrong format.
As the return value of pcifront_try_connect() and
pcifront_attach_devices() are not used anywhere make those functions
return void. As an additional bonus this removes the dubious return
of -EFAULT in case of an unexpected driver state.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
- Add macros for PCI Configuration Mechanism #1 and use them in the
ftpci100, mt7621, and tegra drivers (Pali Rohár)
* remotes/lorenzo/pci/misc:
PCI: tegra: Use PCI_CONF1_EXT_ADDRESS() macro
PCI: mt7621: Use PCI_CONF1_EXT_ADDRESS() macro
PCI: ftpci100: Use PCI_CONF1_ADDRESS() macro
PCI: Add standard PCI Config Address macros
- List platforms that use a single MSI host interrupt in qcom DT (Johan
Hovold)
- Add SC8280XP, SA8540P support to qcom DT binding and driver(Johan Hovold)
- Make all optional clocks truly optional in the driver (Johan Hovold)
- Rename per-IP structs to reflect the IP version (Johan Hovold)
- Sort device ID match table by compatible string (Johan Hovold)
- Add MODULE_DEVICE_TABLE to enable module autoloading (Dmitry Baryshkov)
- Drop the unused .post_deinit() callback (Johan Hovold)
- Rely on DT for clock information instead of hard-coding it in the driver
(Manivannan Sadhasivam)
- Disable IRQs when removing driver to avoid spurious IRQs later
(Manivannan Sadhasivam)
- Expose link transition counts via debugfs to help debug issues with
low-power states (Manivannan Sadhasivam)
- Gate Master AXI clock to the MHI bus while in L1 substates to save power
(Manivannan Sadhasivam)
- Disable Master AXI clock to save power when there is no traffic on PCIe
(Manivannan Sadhasivam)
- Make the "PERST separation" debug feature optional in the DT and the
driver (Manivannan Sadhasivam)
- Define clocks to be per-platform in DT to prepare for future SoCs
(Manivannan Sadhasivam)
- Add SM8450 SoC support (Manivannan Sadhasivam)
- Check for platform_get_resource_byname() to avoid a NULL pointer
dereference (Yang Yingliang)
* pci/qcom:
PCI: qcom-ep: Check platform_get_resource_byname() return value
PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Define clocks per platform
PCI: qcom-ep: Make PERST separation optional
dt-bindings: PCI: qcom-ep: Make PERST separation optional
PCI: qcom-ep: Disable Master AXI Clock when there is no PCIe traffic
PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SS
PCI: qcom-ep: Expose link transition counts via debugfs
PCI: qcom-ep: Disable IRQs during driver remove
PCI: qcom-ep: Make use of the cached dev pointer
PCI: qcom-ep: Rely on the clocks supplied by devicetree
PCI: qcom-ep: Add kernel-doc for qcom_pcie_ep structure
PCI: qcom: Rename host-init error label
PCI: qcom: Drop unused post_deinit callback
PCI: qcom-ep: Add MODULE_DEVICE_TABLE
PCI: qcom: Sort device-id table
PCI: qcom: Clean up IP configurations
PCI: qcom: Make all optional clocks optional
PCI: qcom: Add support for SA8540P
PCI: qcom: Add support for SC8280XP
dt-bindings: PCI: qcom: Add SA8540P to binding
dt-bindings: PCI: qcom: Add SC8280XP to binding
dt-bindings: PCI: qcom: Enumerate platforms with single msi interrupt
- Rename the pcie-mediatek-gen3 driver from 'mtk-pcie' to 'mtk-pcie-gen3'
so it can coexist with the pcie-mediatek driver, which also uses
'mtk-pcie' (Felix Fietkau)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek-gen3: Change driver name to mtk-pcie-gen3
- Use dmam_alloc_coherent() instead of dma_map_page() to allocate the MSI
target page, which means dwc drivers will work even when ZONE_DMA32 is
disabled (Will McVicker)
- If we can't allocate an MSI target page with a 32-bit address, try
allocating one with a 64-bit address (Will McVicker)
- Switch from of_gpio_named_count() to generic gpiod_count() (Andy
Shevchenko)
- Add support for i.MX8MP PCIe (Richard Zhu)
- Fix the Freescale i.MX8 PHY driver, which had interchanged the phy_init()
and phy_power_on() interfaces (Richard Zhu)
* remotes/lorenzo/pci/dwc:
phy: freescale: imx8m-pcie: Fix the wrong order of phy_init() and phy_power_on()
PCI: imx6: Add i.MX8MP PCIe support
PCI: dwc: Replace of_gpio_named_count() by gpiod_count()
PCI: dwc: Drop dependency on ZONE_DMA32
- In an emulated PCI bridge, set Capability offsets so they match the
hardware offsets shown by U-Boot (Pali Rohár)
* remotes/lorenzo/pci/bridge-emul:
PCI: pci-bridge-emul: Set position of PCI capabilities to real HW value
- Switch from gpiod_get_from_of_node() to generic devm GPIO API (Dmitry
Torokhov)
* remotes/lorenzo/pci/apple:
PCI: apple: Do not leak reset GPIO on unbind/unload/error
- Emulate the PCI Bridge Subsystem Vendor ID (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Add support for PCI Bridge Subsystem Vendor ID on emulated bridge
- Distribute resources to unconfigured hotplug bridges at boot-time (not
just when hot-adding such a bridge), which makes hot-adding devices to
docks work (Mika Westerberg)
- Fix the "revert to firmware assignment" code so we do the revert only if
the address is actually reachable. Previously we sometimes assigned
addresses that could not be reached via upstream bridges (Maciej W.
Rozycki)
* pci/resource:
PCI: Sanitise firmware BAR assignments behind a PCI-PCI bridge
PCI: Fix typo in pci_scan_child_bus_extend()
PCI: Fix whitespace and indentation
PCI: Distribute available resources for root buses, too
PCI: Move pci_assign_unassigned_root_bus_resources()
PCI: Pass available buses even if the bridge is already configured
PCI: Fix used_buses calculation in pci_scan_child_bus_extend()
- Expose a sysfs interface for configuring Resizable BARs so we can resize
BARs before assigning devices to a VM through VFIO (Alex Williamson)
* pci/rebar:
PCI: Expose PCIe Resizable BAR support via sysfs
- Cache the PTM capability offset instead of searching for it every time
(Bjorn Helgaas)
- Separate PTM configuration from PTM enable (Bjorn Helgaas)
- Add pci_suspend_ptm() and pci_resume_ptm() to disable and re-enable PTM
on suspend/resume so some Root Ports can safely enter a lower-power PM
state (Bjorn Helgaas)
- Disable PTM for all devices during suspend; previously we only did this
for Root Ports and even then only in certain cases (Bjorn Helgaas)
- Simplify pci_pm_suspend_noirq() (Rajvi Jingar)
- Reduce the delay after transitions to/from D3hot by using usleep_range()
instead of msleep(), which reduces the typical delay from 19ms to 10ms
(Sajid Dalvi, Will McVicker)
* pci/pm:
PCI/PM: Reduce D3hot delay with usleep_range()
PCI/PM: Simplify pci_pm_suspend_noirq()
PCI/PM: Always disable PTM for all devices during suspend
PCI/PTM: Consolidate PTM interface declarations
PCI/PTM: Reorder functions in logical order
PCI/PTM: Preserve RsvdP bits in PTM Control register
PCI/PTM: Move pci_ptm_info() body into its only caller
PCI/PTM: Add pci_suspend_ptm() and pci_resume_ptm()
PCI/PTM: Separate configuration and enable
PCI/PTM: Add pci_upstream_ptm() helper
PCI/PTM: Cache PTM Capability offset
- Correct a typo in 71020a3c0d ('PCI/MSI: Use msi_add_msi_desc()') that
reversed the sense of 'can_mask' in msi_add_msi_desc() (Josef Johansson)
* pci/msi:
PCI/MSI: Correct 'can_mask' test in msi_add_msi_desc()
- Work around a BIOS defect that makes some Intel Root Ports report an RP
PIO log size of zero (Mika Westerberg)
* pci/dpc:
PCI/DPC: Quirk PIO log size for certain Intel Root Ports
If platform_get_resource_byname() fails, 'mmio_res' will be set to NULL
pointer, which causes a NULL pointer dereference when it is used in
qcom_pcie_perst_deassert().
Check the return value to prevent it.
Link: https://lore.kernel.org/r/20220429080740.1294797-1-yangyingliang@huawei.com
Fixes: f55fee56a6 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Add support for SM8450 SoC to the Qualcomm PCIe Endpoint Controller
driver. The driver uses the same config as the existing SDX55 chipset,
so additional settings are not required.
Link: https://lore.kernel.org/r/20220914075350.7992-13-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PERST separation is an optional debug feature used to collect the crash
dump from the PCIe endpoint devices by the PCIe host when the endpoint
crashes. This feature keeps the PCIe link up by separating the PCIe IP
block from the SoC reset logic.
Make the property optional in the driver.
Link: https://lore.kernel.org/r/20220914075350.7992-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Master AXI clock can be disabled when it is not used i.e., when there
is no traffic on the PCIe bus. This helps to save power during idle state.
[bhelgaas: tidy and wrap comment]
Link: https://lore.kernel.org/r/20220914075350.7992-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a simple sysfs interface to Resizable BAR support, largely for the
purposes of assigning such devices to a VM through VFIO. Resizable BARs
present a difficult feature to expose to a VM through emulation, as
resizing a BAR is done on the host. It can fail, and often does, but we
have no means via emulation of a PCIe REBAR capability to handle the error
cases.
A vfio-pci specific ioctl interface is also cumbersome as there are often
multiple devices within the same bridge aperture and handling them is a
challenge. In the interface proposed here, expanding a BAR potentially
requires such devices to be soft-removed during the resize operation and
rescanned after, in order for all the necessary resources to be released.
A pci-sysfs interface is also more universal than a vfio specific
interface.
Please see the ABI documentation update for usage.
Link: https://lore.kernel.org/r/166336088796.3597940.14973499936692558556.stgit@omen
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: Krzysztof Wilczyński <kw@linux.com>
80d7d7a904 ("PCI/ASPM: Calculate LTR_L1.2_THRESHOLD from device
characteristics") replaced a fixed value (163840ns) with one computed from
T_POWER_OFF, Common_Mode_Restore_Time, etc., but it encoded the
LTR_L1.2_THRESHOLD value incorrectly.
This is especially a problem for small thresholds, e.g., 63ns fell into the
"threshold_ns < 1024" case and was encoded as 32ns:
LTR_L1.2_THRESHOLD_Scale = 1 (multiplier is 32ns)
LTR_L1.2_THRESHOLD_Value = 63 >> 5 = 1
LTR_L1.2_THRESHOLD = multiplier * value = 32ns * 1 = 32ns
Correct the algorithm to encode all times of 1023ns (0x3ff) or smaller
exactly and larger times conservatively (the encoded threshold is never
smaller than was requested). This reduces the chance of entering L1.2
when the device can't tolerate the exit latency.
Fixes: 80d7d7a904 ("PCI/ASPM: Calculate LTR_L1.2_THRESHOLD from device characteristics")
Link: https://lore.kernel.org/r/20221005025809.2247547-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
187f91db82 ("PCI/ASPM: Remove struct aspm_register_info.l1ss_cap")
inadvertently removed a check for existence of the L1 PM Substates (L1SS)
Capability before reading it.
If there is no L1SS Capability, this means we mistakenly read PCI_COMMAND
and PCI_STATUS (config address 0x04) and interpret that as the PCI_L1SS_CAP
register, so we may incorrectly configure L1SS.
Make sure the L1SS Capability exists before trying to read it.
Fixes: 187f91db82 ("PCI/ASPM: Remove struct aspm_register_info.l1ss_cap")
Link: https://lore.kernel.org/r/20221005025809.2247547-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Qualcomm PCIe controllers have debug registers in the MMIO region
that count PCIe link transitions. Expose them over debugfs to
userspace to help debug the low power issues.
Link: https://lore.kernel.org/r/20220914075350.7992-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Disable the Global and PERST IRQs during driver remove to avoid getting
spurious IRQs after resource deallocation.
Link: https://lore.kernel.org/r/20220914075350.7992-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Previously the L1 PM Substates Control Registers (CTL1 and CTL2) weren't
saved and restored during suspend/resume leading to the L1 PM Substates
configuration being lost post-resume.
Save the L1 PM Substates Control Registers so that the configuration is
retained post-resume.
[bhelgaas: drop pci_is_pcie() testing; we can rely on pci_configure_ltr()
having already done that]
Link: https://lore.kernel.org/r/20220913131822.16557-3-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
An HVM guest with linux stubdomain and 2 PCI devices failed to start as
libxl timed out waiting for the PCI devices to be added. It happens
intermittently but with some regularity. libxl wrote the two xenstore
entries for the devices, but then timed out waiting for backend state 4
(Connected) - the state stayed at 7 (Reconfiguring). (PCI passthrough
to an HVM with stubdomain is PV passthrough to the stubdomain and then
HVM passthrough with the QEMU inside the stubdomain.)
The stubdomain kernel never printed "pcifront pci-0: Installing PCI
frontend", so it seems to have missed state 4 which would have
called pcifront_try_connect() -> pcifront_connect_and_init_dma()
Have pcifront_detach_devices() special-case state Initialised and call
pcifront_connect_and_init_dma(). Don't use pcifront_try_connect()
because that sets the xenbus state which may throw off the backend.
After connecting, skip the remainder of detach_devices since none have
been initialized yet. When the backend switches to Reconfigured,
pcifront_attach_devices() will pick them up again.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220829151536.8578-1-jandryuk@gmail.com
Signed-off-by: Juergen Gross <jgross@suse.com>
In the qcom_pcie_ep_get_resources() function, dev pointer is already
cached in a local variable. So let's make use of it instead of getting
the dev pointer again from pdev struct.
Link: https://lore.kernel.org/r/20220914075350.7992-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Generally, device drivers should just rely on the platform data like
devicetree to supply the clocks required for the functioning of the
peripheral. There is no need to hardcode the clk info in the driver.
So get rid of the static clk info and obtain the platform supplied
clks.
The total number of clocks supplied is obtained using the
devm_clk_bulk_get_all() API and used for the rest of the clk_bulk_ APIs.
Link: https://lore.kernel.org/r/20220914075350.7992-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Refer to phy_core driver, phy_init() must be called before phy_power_on().
Fix the wrong order of phy_init() and phy_power_on() here.
Link: https://lore.kernel.org/r/1662344583-18874-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 1aa97b0022 ("phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Add i.MX8MP PCIe support.
To avoid codes duplication when find the syscon regmap, add the iomux
gpr syscon compatible into drvdata.
Link: https://lore.kernel.org/r/1662109086-15881-8-git-send-email-hongxing.zhu@nxp.com
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
As a preparation to unexport of_gpio_named_count(), convert the
driver to use gpiod_count() instead.
Link: https://lore.kernel.org/r/20220830183310.48541-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
