The new Surface Laptop Studio uses GPEs for lid events as well. Add an
entry for that so that the lid can be used to wake the device.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20211021111053.564133-1-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
RTC based wakeup from s0i3 doesn't work properly on some Green Sardine
platforms. Because of this, a newer SMU for Green Sardine has the ability
to pass wakeup time as argument of the upper 16 bits of OS_HINT message.
With older firmware setting the timer value in OS_HINT will cause firmware
to reject the hint, so only run this path on:
1) Green Sardine
2) Minimum SMU FW
3) RTC alarm armed during s0i3 entry
Using this method has some limitations that the s0i3 wakeup will need to
be between 4 seconds and 18 hours, so check those boundary conditions as
well and abort the suspend if RTC is armed for too short or too long of a
duration.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20211020162946.10537-2-mario.limonciello@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Currently the "argument" for the "message" is listed as a boolean
value. This works well for the commands used currently, but an
additional upcoming command will pass more data in the message.
Expand it to be a full 32 bit value.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20211020162946.10537-1-mario.limonciello@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a driver providing access to the GPIOs for the identify button and led
present on Barco P50 board, based on the pcengines-apuv2.c driver.
There is unfortunately no suitable ACPI entry for the EC communication
interface, so instead bind to boards with "P50" as their DMI product family
and hard code the I/O port number (0x299).
The driver also hooks up the leds-gpio and gpio-keys-polled drivers to the
GPIOs, so they are finally exposed as:
LED:
/sys/class/leds/identify
Button: (/proc/bus/input/devices)
I: Bus=0019 Vendor=0001 Product=0001 Version=0100
N: Name="identify"
P: Phys=gpio-keys-polled/input0
S: Sysfs=/devices/platform/barco-p50-gpio/gpio-keys-polled/input/input10
U: Uniq=
H: Handlers=event10
B: PROP=0
B: EV=3
B: KEY=1000000 0 0 0 0 0 0
Signed-off-by: Santosh Kumar Yadav <santoshkumar.yadav@barco.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20211020123634.2638-1-peter@korsgaard.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
A new warning in clang points out a use of bitwise OR with boolean
expressions in this driver:
drivers/platform/x86/thinkpad_acpi.c:9061:11: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical]
else if ((strlencmp(cmd, "level disengaged") == 0) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/platform/x86/thinkpad_acpi.c:9061:11: note: cast one or both operands to int to silence this warning
1 error generated.
This should clearly be a logical OR so change it to fix the warning.
Fixes: fe98a52ce7 ("ACPI: thinkpad-acpi: add sysfs support to fan subdriver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1476
Reported-by: Tor Vic <torvic9@mailbox.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211018182537.2316800-1-nathan@kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
coccicheck complains about the use of snprintf() in sysfs show
functions:
WARNING use scnprintf or sprintf
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Link: https://lore.kernel.org/r/20211018091750.858826-1-ye.guojin@zte.com.cn
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
show() must not use snprintf() when formatting the value to be
returned to user space.
Fix the coccicheck warnings:
WARNING: use scnprintf or sprintf.
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Signed-off-by: Qing Wang <wangqing@vivo.com>
Link: https://lore.kernel.org/r/1634280641-4862-1-git-send-email-wangqing@vivo.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The ACPI_HANDLE() macro is a wrapper arond the ACPI_COMPANION()
macro and the ACPI handle produced by the former comes from the
ACPI device object produced by the latter, so it is way more
straightforward to evaluate the latter directly instead of passing
the handle produced by the former to acpi_bus_get_device().
Modify ideapad_acpi_add() accordingly (no intentional functional
impact).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/8000884.T7Z3S40VBb@kreacher
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
If the ACPI companion of a given device is not present, the result
of the ACPI_HANDLE() evaluation for it will be NULL, so calling
acpi_bus_get_device() on ACPI_HANDLE() result in order to validate
it is redundant.
Drop the redundant acpi_bus_get_device() call from mshw0011_notify()
along with a local variable related to it.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/3160001.aeNJFYEL58@kreacher
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The ACPI_HANDLE() macro is a wrapper arond the ACPI_COMPANION()
macro and the ACPI handle produced by the former comes from the
ACPI device object produced by the latter, so it is way more
straightforward to evaluate the latter directly instead of passing
the handle produced by the former to acpi_bus_get_device().
Modify s3_wmi_check_platform_device() accordingly (no intentional
functional impact).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/12896717.uLZWGnKmhe@kreacher
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Create the attribute groups for kb_led_color and set the `groups` field
in kb_led. While touching it, also change its show method to use
sysfs_emit() instead of sprintf().
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Link: https://lore.kernel.org/r/20211006202202.7479-5-tcrawford@system76.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
System76 laptops running open source EC firmware support configuring
charging thresholds through ACPI methods. Expose this functionality
through the standard sysfs entries charge_control_{start,end}_threshold.
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Link: https://lore.kernel.org/r/20211006202202.7479-4-tcrawford@system76.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
System76 laptops models with OLED displays do not support the default
Fn+F2 behavior of turning the embedded display on and off. Some models
instead introduce a new notify event that is used to lock the screen so
the OS will put the display in a low power state.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Link: https://lore.kernel.org/r/20211006202202.7479-3-tcrawford@system76.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a hwmon interface to report CPU/GPU temperature and fan speed.
sensors now reports an ACPI interface with the entries:
system76_acpi-acpi-0
Adapter: ACPI interface
CPU fan: 0 RPM
GPU fan: 0 RPM
CPU temp: +47.0°C
GPU temp: +0.0°C
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Link: https://lore.kernel.org/r/20211006202202.7479-2-tcrawford@system76.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add new registers to support systems with multiply cooling devices.
Modular systems support up-to four cooling devices. This capability
is detected according to the registers initial setting.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael <michaelsh@nvidia.com>
Link: https://lore.kernel.org/r/20211002093609.3771576-1-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Provide support for the Nvidia MSN4800-XX line cards for MSN4800
Ethernet modular switch system, providing a high performance switching
solution for Enterprise Data Centers (EDC) for building Ethernet based
clusters, High-Performance Computing (HPC) and embedded environments.
Initial version provides support for line card type MSN4800-C16. This
type of line card is equipped with:
- Lattice CPLD device, used for system and ports control.
- four Nvidia gearbox devices, used for port splitting.
- FPGA device, used for gearboxes management.
- 16x100G QSFP28 ports.
- hotpswap controllers, voltage regulators, analog-to-digital
convertors, nvram devices.
- status LED.
During initialization driver creates:
- line card's I2C tree through "i2c-mux-mlxcpd" driver.
- line card's LED objects through "leds-mlxreg" driver.
- line card's CPLD register space input / output "hwmon" attributes for
line control and monitoring through "mlxreg-io" driver. These
attributes provide CPLD and FPAG versioning, control for upgradable
components burning, NVRAM devices write protection, line card
revision, line card power consuming, line card reset cause
indication, etcetera.
Lattice CPLD device and nvram devices are feeding from auxiliary power
domain and accessible, when line card is powered off. These devices
are connected by line card driver probing routine, invoked after line
card security verification is done by hardware and event lc#n_verified
is received for line card located in slot #n.
Gearboxes, FPGA, hotpswap controllers, voltage regulators,
analog-to-digital convertors are feeding from main power domain. These
devices are connected after power good event "lc#n_powered" is received
for line card located in slot #n.
The driver 'mlxreg-lc' is driven by 'mlxreg-hotplug' driver following
relevant "hotplug" events.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Link: https://lore.kernel.org/r/20211002093238.3771419-8-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Extend maximum number of the attributes, exposed to 'sysfs'.
It is requires in order to support modular systems, which
provide more attributes for system control, statuses and info.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Link: https://lore.kernel.org/r/20211002093238.3771419-6-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add event notifier callbacks for modular system line cards. These
callbacks are to be passed to "mlxreg-hotplug" driver by line card
driver during probing. Then, when any line card related hotplug event
is received (insertion ,power, synch, ready), hotplug driver will
invoke callback for the relevant line card.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Link: https://lore.kernel.org/r/20211002093238.3771419-5-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Extend the structure 'mlxreg_hotplug_device" with platform device field
to allow transition of the register map and system interrupt line number
to underlying hotplug devices, sharing the same register map and
same interrupt line with 'mlxreg-hotplug' driver.
Extend logic for hotplug devices creation and removing according to
the action associated with the hotplug device description. Previously
hotplug driver was capable to attach / de-attach upon hotplug events
only I2C devices handled by simple I2C drivers. Now it should be able
to attach also devices handled by the platform drivers.
The motivation is to allow transition of platform data like:
- system interrupt line number, sharing with 'mlxreg-hotplug' to
underlying hotplug devices.
- shared register map of programmable devices on main board to
underlying hotplug devices.
Additioanlly the number of 'sysfs' attributes is increased, since
modular system defines more 'sysfs' attributes.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Link: https://lore.kernel.org/r/20211002093238.3771419-4-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add initial chassis management support for Nvidia modular Ethernet
switch systems MSN4800, providing a high performance switching solution
for Enterprise Data Centers (EDC) for building Ethernet based clusters,
High-Performance Computing (HPC) and embedded environments.
This system could be equipped with the different types of replaceable
line cards and management board. The first system flavor will support
the line card type MSN4800-C16 equipped with Lattice CPLD devices aimed
for system and ASIC control, one Nvidia FPGA for gearboxes (PHYs)
management, and four Nvidia gearboxes for the port control and with
16x100GbE QSFP28 ports and also with various devices for electrical
control.
The system is equipped with eight slots for line cards, four slots for
power supplies and six slots for fans. It could be configured as fully
populated or with even only one line card. The line cards are
hot-pluggable.
In the future when more line card flavors are to be available (for
example line cards with 8x200Gb Eth port, with 4x400 Eth ports, or with
some kind of smart cards for offloading purpose), any type of line card
could be inserted at any slot.
The system is based on Nvidia Spectrum-3 ASIC. The switch height is
4U and it fits standard rack size.
System could be configured as fully populated or with even only one
line card. The line cards are hot-pluggable.
Line cards are connected to the chassis through I2C interface for the
chassis management operations and through PCIe for the networking
operations. Future line cards could be connected to the chassis through
InfiniBand fabric, instead of PCIe.
The first type of line card supports 16x100GbE QSFP28 Ethernet ports.
Those line cards equipped with the programmable devices aimed for
system control of Nvidia Ethernet switch ASIC control, Nvidia FPGA,
Nvidia gearboxes (PHYs).
The next coming card generations are supposed to support:
- Line cards with 8x200Gbe QSFP28 Ethernet ports.
- Line cards with 4x400Gbe QSFP-DD Ethernet ports.
- Smart cards equipped with Nvidia ARM CPU for offloading and for fast
access to the storage (EBoF).
- Fabric cards for inter-connection.
The basic system initialization flow with input signals from the
programmable device to kernel hotplug driver and with OS response
to some of these signals is depicted below.
lc#n_prsnt *-> Input: line card presence in/out events.
Informational event. Required action - 'udev' event
generation for logging.
lc#n_verified *-> Input: line card verification status events coming
after line card security signature validation by
hardware. Required action - connect line card
driver and initialized line card devices feeding
from system auxiliary power domain.
lc#n_pwr <-* Output: line card power on / off from OS. Action
should be performed by platform power management
driver.
lc#n_powered *-> Input: line card power on/off events coming after
line card "power good" on/off events, mean that
line card power up sequence has been successfully
completed or line card "power good" status has been
dropped. Required action - connect line card
devices feeding from system main power domain.
lc#n_synced *-> Input: line card synchronization events, coming
after hardware-firmware synchronization handshake.
Required action - to enable line card, in case
lc#n_ready has been received before.
lc#n_ready *-> Input: line card ready events, indicating line card
PHYs ready / unready states. Required action -
enable line card, in case lc#n_synced has been
received before.
lc#n_enable <-* Output: line card enable from OS - release FPGA and
PHYs line card devices from reset state. Action
should be performed by platform power management
driver.
lc#n_active *-> Input: when line card "active event" is received
for particular line card, its network, hardware
monitoring and thermal interfaces should be
configured according to the configuration obtained
from the firmware. When opposite "inactive event"
is received all the above interfaces should be
teared down. Required action - connect / disconnect
the above line card interfaces through ASIC I2C
chassis management driver.
For initial support:
- Define new system type 'VMOD0011' to support new modular system.
- Provide initial platform configuration for new system type.
- Extend the registers definitions.
- Add support for modular system registers related to line card
specific events - insertion/removal, power on/off, verification
and activation.
- Add hotplug configuration for the above events.
- Add configurations for hotplug actions for the modular system.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Link: https://lore.kernel.org/r/20211002093238.3771419-3-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
SAR information from BIOS may come in non sequential pattern.
To overcome the issue, a check is made to extract the right SAR
information using the device mode which is currently being used.
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Shravan S <s.shravan@intel.com>
Link: https://lore.kernel.org/r/20211006073525.1332925-1-s.shravan@intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The int3472-discrete driver can enter an error path after initialising
int3472->clock.ena_gpio, but before it has registered the clock. This will
cause a NULL pointer dereference, because clkdev_drop() is not null aware.
Instead of guarding the call to skl_int3472_unregister_clock() by checking
for .ena_gpio, check specifically for the presence of the clk_lookup, which
will guarantee clkdev_create() has already been called.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=214453
Fixes: 7540599a5e ("platform/x86: intel_skl_int3472: Provide skl_int3472_unregister_clock()")
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Link: https://lore.kernel.org/r/20211008224608.415949-1-djrscally@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The comment decribing the IPC timeout hadn't been updated when the
actual timeout was changed from 3 to 5 seconds in
commit a7d53dbbc7 ("platform/x86: intel_scu_ipc: Increase virtual
timeout from 3 to 5 seconds") .
Since the value is anyway updated to 10s now, take this opportunity to
update the value in the comment too.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20210928101932.2543937-4-pmalani@chromium.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit a7d53dbbc7 ("platform/x86: intel_scu_ipc: Increase virtual
timeout from 3 to 5 seconds") states that the recommended timeout range
is 5-10 seconds. Adjust the timeout value to the higher of those i.e 10
seconds, to account for situations where the 5 seconds is insufficient
for disconnect command success.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20210928101932.2543937-3-pmalani@chromium.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The macro IPC_TIMEOUT is already in jiffies (it is also used like that
elsewhere in the file when calling wait_for_completion_timeout()). Don’t
convert it using helper functions for the purposes of calculating the
busy loop expiry time.
Fixes: e7b7ab3847 (“platform/x86: intel_scu_ipc: Sleeping is fine when polling”)
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20210928101932.2543937-2-pmalani@chromium.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
DELL_WMI_PRIVACY is a feature toggle for the main dell-wmi driver,
so it must depend on the Kconfig option which enables the main
dell-wmi driver.
Fixes: 8af9fa37b8 ("platform/x86: dell-privacy: Add support for Dell hardware privacy")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211011132338.407571-1-hdegoede@redhat.com
Rename the wmaa-backlight-wmi driver and associated KConfig option to
remove the remaining references to the "WMAA" ACPI handle which was
used in the previous name. The driver has already been updated to
remove internal references to "WMAA". As part of the renaming, the
components in the name have been rearranged to reflect the standard
vendor_wmi_feature pattern.
Signed-off-by: Daniel Dadap <ddadap@nvidia.com>
Link: https://lore.kernel.org/r/20210927202359.13684-2-ddadap@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The "wmaa" in the name of the wmaa-backlight-wmi driver was named after
the ACPI method handle for EC-based backlight control on the systems
this driver was tested on during development. However, this "WMAA"
handle is generated by the WMI compilation process, and isn't actually
a part of the backlight control mechanism which this driver supports.
Since the "WMAA" handle isn't actually a part of the firmware backlight
interface, the various identifiers in this driver using "WMAA" or
"wmaa" aren't actually appropriate.
As a common denominator across the systems supported by this driver is
that they are hybrid graphics systems with NVIDIA GPUs, using "nvidia"
in the driver name seems more appropriate than "wmaa". Update the
driver to remove "wmaa" and "WMAA" in identifier names where they
appear. The kerneldoc comments for the enum wmi_brightness_method
values are replaced with the verbatim text from the decompiled BMF code
for this WMI class.
Signed-off-by: Daniel Dadap <ddadap@nvidia.com>
Link: https://lore.kernel.org/r/20210927202359.13684-1-ddadap@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fix shift argument for function rol32(). It should be provided in bits,
while was provided in bytes.
Fixes: 86148190a7 ("platform/mellanox: mlxreg-io: Add support for complex attributes")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210927142214.2613929-3-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Change kstrtou32() argument 'base' to be zero instead of 'len'.
It works by chance for setting one bit value, but it is not supposed to
work in case value passed to mlxreg_io_attr_store() is greater than 1.
It works for example, for:
echo 1 > /sys/devices/platform/mlxplat/mlxreg-io/hwmon/.../jtag_enable
But it will fail for:
echo n > /sys/devices/platform/mlxplat/mlxreg-io/hwmon/.../jtag_enable,
where n > 1.
The flow for input buffer conversion is as below:
_kstrtoull(const char *s, unsigned int base, unsigned long long *res)
calls:
rv = _parse_integer(s, base, &_res);
For the second case, where n > 1:
- _parse_integer() converts 's' to 'val'.
For n=2, 'len' is set to 2 (string buffer is 0x32 0x0a), for n=3
'len' is set to 3 (string buffer 0x33 0x0a), etcetera.
- 'base' is equal or greater then '2' (length of input buffer).
As a result, _parse_integer() exits with result zero (rv):
rv = 0;
while (1) {
...
if (val >= base)-> (2 >= 2)
break;
...
rv++;
...
}
And _kstrtoull() in their turn will fail:
if (rv == 0)
return -EINVAL;
Fixes: 5ec4a8ace0 ("platform/mellanox: Introduce support for Mellanox register access driver")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210927142214.2613929-2-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, to avoid open-coded arithmetic in the kzalloc() call inside the
create_attr_set() function the code must be refactored. Using the
struct_size() helper is the fast solution but it is better to switch
this code to common use of attributes.
Then, remove all the custom code to manage hotkey attributes and use the
attribute_group structure instead, refactoring the code accordingly.
Also, to manage the optional hotkey attributes (hotkey_tablet_mode and
hotkey_radio_sw) use the is_visible callback from the same structure.
Moreover, now the hotkey_init_tablet_mode() function never returns a
negative number. So, the check after the call can be safely removed.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Len Baker <len.baker@gmx.com>
Link: https://lore.kernel.org/r/20210926111908.6950-1-len.baker@gmx.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Adding support specifically for Ideapad 5 Pro 16ACH6-82L5 by adding a
allow list that can validate notebooks for which dytc_version
is less than 5, and seem to work fine at dytc_version 4. This code has
been tested to work properly on the specified system.
Signed-off-by: Kelly Anderson <kelly@xilka.com>
Link: https://lore.kernel.org/r/11840239.O9o76ZdvQC@comer.internal
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a message to print the resume time information obtained from the
smu_metrics structure.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Link: https://lore.kernel.org/r/20210921120020.19454-1-Sanket.Goswami@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
It was reported that the resume stats received from the firmware are
always zero. This happens because the SMU expects the driver to send the
command to dump the log data after clearing the OS_HINT.
Adjust the order of the commands sent to SMU.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Link: https://lore.kernel.org/r/20210921115910.19401-1-Sanket.Goswami@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The amd_pmc_get_smu_version() and amd_pmc_idlemask_read() functions are
used in the probe / suspend/resume code, so they are also used when
CONFIG_DEBUGFS is disabled, move them outside of the #ifdef CONFIG_DEBUGFS
block.
Note this purely moves the code to above the #ifdef CONFIG_DEBUGFS,
the code is completely unchanged.
Fixes: f6045de1f5 ("platform/x86: amd-pmc: Export Idlemask values based on the APU")
Cc: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Cc: Sanket Goswami <Sanket.Goswami@amd.com>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Adds support for:
- Dell Inspiron 2in1 tablet mode switch notifications. These are
delivered by a type 0x0011 message with code 0xe070, followed by a
flag (1 for laptop mode, 0 for tablet mode).
- Recognising (but not otherwise processing) the Dell Ultra Performance
mode request switch. This is delivered by a type 0x0012 message with
code 0x000d, followed by a parameter that is either 1 or 2. It is
not clear what (if anything) should be done with this notification, so
it is ignored.
Signed-off-by: Troy Rollo <linux2021@troy.rollo.name>
Link: https://lore.kernel.org/r/20210918073131.2966942-1-linux2021@troy.rollo.name
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some devices, even non convertible ones, can send incorrect
SW_TABLET_MODE reports.
Add an allow list and accept such reports only from devices in it.
Bug reported for Dell XPS 17 9710 on:
https://gitlab.freedesktop.org/libinput/libinput/-/issues/662
Reported-by: Tobias Gurtzick <magic@wizardtales.com>
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Tobias Gurtzick <magic@wizardtales.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20210920160312.9787-1-jose.exposito89@gmail.com
[hdegoede@redhat.com: Check dmi_switches_auto_add_allow_list only once]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When DELL_WMI=y, DELL_WMI_PRIVACY=y, and LEDS_TRIGGER_AUDIO=m, there
is a linker error since the LEDS trigger code is built as a loadable
module. This happens because DELL_WMI_PRIVACY is a bool that depends
on a tristate (LEDS_TRIGGER_AUDIO=m), which can be dangerous.
ld: drivers/platform/x86/dell/dell-wmi-privacy.o: in function `dell_privacy_wmi_probe':
dell-wmi-privacy.c:(.text+0x3df): undefined reference to `ledtrig_audio_get'
Fixes: 8af9fa37b8 ("platform/x86: dell-privacy: Add support for Dell hardware privacy")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Perry Yuan <Perry.Yuan@dell.com>
Cc: Dell.Client.Kernel@dell.com
Cc: platform-driver-x86@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Gross <mgross@linux.intel.com>
Link: https://lore.kernel.org/r/20210918044829.19222-1-rdunlap@infradead.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The MODULE_DEVICE_TABLE already creates proper alias for ACPI driver.
Having another MODULE_ALIAS causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210916170054.136790-1-krzysztof.kozlowski@canonical.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
IdleMask is the metric used by the PM firmware to know the status of each
of the Hardware IP blocks monitored by the PM firmware.
Knowing this value is key to get the information of s2idle suspend/resume
status. This value is mapped to PMC scratch registers, retrieve them
accordingly based on the CPU family and the underlying firmware support.
Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20210916124002.2529-1-Sanket.Goswami@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
As the PM firmware returns the status of the last s0i3 in the smu_metrics
structure, the existing name "s0i3_cyclecount" seems to be a misnomer.
Change it accordingly to "s0i3_last_entry_status".
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20210916124130.2581-1-Sanket.Goswami@amd.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This driver is for accessing the PSE (Programmable Service Engine) - an
Embedded Controller like IP - using ISHTP (Integratd Sensor Hub Transport
Protocol) to get battery, thermal and UCSI (USB Type-C Connector System
Software Interface) related data from the platform.
Signed-off-by: K Naduvalath, Sumesh <sumesh.k.naduvalath@intel.com>
Reviewed-by: Mark Gross <mgross@linux.intel.com>
Link: https://lore.kernel.org/r/20210913051056.28736-1-sumesh.k.naduvalath@intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
checkpatch.pl tool warns about using __attribute__((packed))
"WARNING: __packed is preferred over __attribute__((packed))"
To fix this __attribute__((packed)) is replaced by __packed
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Link: https://lore.kernel.org/r/20210912011741.30495-1-jbi.octave@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Make `find_guid()` return an acpi_status, and make it handle NULL
pointer GUID strings; and adapt users accordingly.
Signed-off-by: Barnabás Pőcze <pobrn@protonmail.com>
Link: https://lore.kernel.org/r/20210904175450.156801-31-pobrn@protonmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Previously, `acpi_wmi_notify_handler()` and `wmi_get_event_data()`
shared more or less the exact same code to query the data for
a particular event.
Introduce a function to get rid of the duplication, and use it
from `acpi_wmi_notify_handler()` and `wmi_get_event_data()`.
Signed-off-by: Barnabás Pőcze <pobrn@protonmail.com>
Link: https://lore.kernel.org/r/20210904175450.156801-30-pobrn@protonmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Introduce helper function to determine the appropriate
ACPI type for the input parameter.
This also fixes the following checkpatch warning:
"braces {} are not necessary for any arm of this statement".
Signed-off-by: Barnabás Pőcze <pobrn@protonmail.com>
Link: https://lore.kernel.org/r/20210904175450.156801-29-pobrn@protonmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
