To ensure the correct size of types, use u64 for the return value of
arch_timer_get_cnt{p,v}ct, and u32 for arch_timer_rate, matching the
size of the registers these values are taken from. While we're changing
them anyway, simplify the implementation of arch_timer_get_cnt{p,v}ct.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This check is a holdover from the pre-devicetree days. As the timer
is not probed except by platforms which register it via devicetree,
it's not strictly necessary.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
When we get the device_node for the arch timer, it's refcount is
automatically incremented in of_find_matching_node, but it is
never decremented.
This patch decrements the refcount on the node after we're finished
using it.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Pull ARM fixes from Russell King.
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7616/1: cache-l2x0: aurora: Use writel_relaxed instead of writel
ARM: 7615/1: cache-l2x0: aurora: Invalidate during clean operation with WT enable
ARM: 7614/1: mm: fix wrong branch from Cortex-A9 to PJ4b
ARM: 7612/1: imx: Do not select some errata that depends on !ARCH_MULTIPLATFORM
ARM: 7611/1: VIC: fix bug in VIC irqdomain code
ARM: 7610/1: versatile: bump IRQ numbers
ARM: 7609/1: disable errata work-arounds which access secure registers
ARM: 7608/1: l2x0: Only set .set_debug on PL310 r3p0 and earlier
People are back from the holiday breaks, and it shows. Here are a bunch of
fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups,
a few __init annotation fixes and some error handling improvement
in their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to see
here, mostly from the OMAP PM changes, but nothing overly crazy.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s9fE
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"People are back from the holiday breaks, and it shows. Here are a
bunch of fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups, a few
__init annotation fixes and some error handling improvement in
their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to
see here, mostly from the OMAP PM changes, but nothing overly crazy."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
pinctrl: mvebu: make pdma clock on dove mandatory
ARM: Dove: Add pinctrl clock to DT
dma: mv_xor: fix error handling for clocks
dma: mv_xor: fix error handling of mv_xor_channel_add()
arm: mvebu: Add missing ; for cpu node.
arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces
arm: mvebu: Armada XP MV78230 has two cores, not one
clk: mvebu: Remove inappropriate __init tagging
ARM: Kirkwood: Use fixed-regulator instead of board gpio call
ARM: Kirkwood: Fix missing sdio clock
ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers
...
on omap2 registers that causes issues trying to use common PM code.
Also fix few incorrect registers, and an issue for omap1 USB, and
few sparse fixes for issues that sneaked in with all the clean-up.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gqPM
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8-rc2/fixes-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
The biggest change is a fix to deal with different power state
on omap2 registers that causes issues trying to use common PM code.
Also fix few incorrect registers, and an issue for omap1 USB, and
few sparse fixes for issues that sneaked in with all the clean-up.
* tag 'omap-for-v3.8-rc2/fixes-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
ARM: OMAP1: fix USB configuration use-after-release
ARM: OMAP2/3: PRM: fix bogus OMAP2xxx powerstate return values
ARM: OMAP3: clock data: Add missing enable/disable for EMU clock
ARM: OMAP4: PRM: Correct wrong instance usage for reading reset sources
ARM: OMAP4: PRM: fix RSTTIME and RSTST offsets
ARM: OMAP4: PRM: Correct reset source map
ARM: OMAP: SRAM: resolve sparse warnings
ARM: OMAP AM33xx: hwmod data: resolve sparse warnings
ARM: OMAP: 32k counter: resolve sparse warnings
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
Most of them are EXYNOS5440 fixes which are for changing uart console,
cpu id (typo) and silent complaining gpio error in kernel boot.
* 'v3.8-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: skip the clock initialization for exynos5440
ARM: EXYNOS: enable PINCTRL for EXYNOS5440
ARM: dts: use uart port1 for console on exynos4210-smdkv310
ARM: dts: use uart port0 for console on exynos5440-ssdk5440
ARM: SAMSUNG: fix the cpu id for EXYNOS5440
ARM: EXYNOS: Revise HDMI resource size
is unresponsive for quite a while. People start complaining the missing
of such an important fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ7DwYAAoJEFBXWFqHsHzOHnUH/2V7EKzq8g6FH5DyOf3+9x9f
I+KyjVusIFdbLIJZhswbTnd2f1k5FQnQ+djd6fERi/wZ8IcG70vPRscKIYrLX6po
gd0z684ORsBwNrHMfcKSY6DwZF2cLtP5BpyvtQzKHpP3nTYBgE7ePSFlfsAdJ5OG
C77/tj61B/bUe0Mm8ygjMCwYsdqaR2+MTdEcStvOmwd4x+PBT3uSd56TFhXW2kt5
Py2d48wowncNM5CVIW7vvH4kaaCW4h6mxnc3gyc8YS8h1JFItdYFSNUzT9Mb5ene
aM3He/pp82OoXm84Swhi5Ah5566WVor+bgnvJ1TmV4Q/yd6Cn+MA2nIOevTnJvo=
=Tjtj
-----END PGP SIGNATURE-----
Merge tag 'mxs-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
I have to send one critical mxsfb fix through arm-soc, as FB maintainer
is unresponsive for quite a while. People start complaining the missing
of such an important fix.
* tag 'mxs-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
video: mxsfb: fix crash when unblanking the display
ARM: dts: imx23-olinuxino: Fix IOMUX settings
when the port gets brought up. The other two are non-critical fixes,
which are sent together here, since it's still early -rc stage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ7Dk+AAoJEFBXWFqHsHzOUugIAJZblDy7ORFZhW0R8L4Be541
pS5aBGFY7VYCrL9BGUKGsLuITI+arbYFHc+H4nqhNMBAvgChPxJZMnaG4kp1Q5Vm
AVr9tNrwsauVHLlryUk4ekut4G4WWo1NDcFq4S6rxD/jxA/uP6rnMUCY6PX4LLL9
ZpGDb3BWQ2bbUaANu3cjc1I1/Gle1ir9LObm6ZC6l8MHTTG7hyTMHvS8eCZzmDbc
9z01ZrvTKn1AneeHOpArd2/jo14b6Kap8ykx2hdVUeBhIbZp3pomezZau9ya8/kB
+1BQVODdkOMzBm6gkIkfU3HbUPnIPL18MG/uKyD+f67YkX5YODinUVdq63upLxc=
=7yrS
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
It includes one critical fix - wrong flexcan2 clock will hang system
when the port gets brought up. The other two are non-critical fixes,
which are sent together here, since it's still early -rc stage.
* tag 'imx-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mx5: Fix MX53 flexcan2 clock
ARM: dts: imx31-bug: Fix manufacturer compatible string
clk: imx: Remove 'clock-output-names' from the examples
- use correct uart driver for mvebu boards
- add a missing DT clocks
- gpio-poweroff level vs. edge triggering, use gpio_is_valid()
- remove an inappropriate __init, modules need to access function.
- various DT fixes
- error handling in mv_xor
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQ6vYDAAoJEAi3KVZQDZAeoHwIAKSw+8B601AixTZus7fp9wrE
M9Tk4VoCflDQ8uIh6sHrHQlwMi8NPVA6ogn6VoEYA7HnA/nGTx/Ij/XCpuPBdt8+
VM5gzonaKK16OswtLmUZIgJKDJt0Q+zw9K7u6UkWQW8IXyGlyK2gxYqJLQPHhebb
D3TyKdJqx7FBr2Oq3MJQshIN/TTSOA+q94oYUogc7qZpjsY8ZgnBbRWVBYEhRa+u
sS0vZ8LV5twOKqATJa4ZCXA4E3WoKOZKTgdXj4IRfRkeQh9WHmhH4aWwq7Kl72Ic
glBA6iCrA/6KvJx9H4AG5BK/Ltg2vfQDKo2XWMQtH8j2WwHfMqHMPS3qivjXg2s=
=jfqF
-----END PGP SIGNATURE-----
Merge tag 'mvebu_fixes_for_v3.8' of git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper:
fixes for mvebu/kirkwood v3.8
- use correct uart driver for mvebu boards
- add a missing DT clocks
- gpio-poweroff level vs. edge triggering, use gpio_is_valid()
- remove an inappropriate __init, modules need to access function.
- various DT fixes
- error handling in mv_xor
* tag 'mvebu_fixes_for_v3.8' of git://git.infradead.org/users/jcooper/linux:
pinctrl: mvebu: make pdma clock on dove mandatory
ARM: Dove: Add pinctrl clock to DT
dma: mv_xor: fix error handling for clocks
dma: mv_xor: fix error handling of mv_xor_channel_add()
arm: mvebu: Add missing ; for cpu node.
arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces
arm: mvebu: Armada XP MV78230 has two cores, not one
clk: mvebu: Remove inappropriate __init tagging
ARM: Kirkwood: Use fixed-regulator instead of board gpio call
ARM: Kirkwood: Fix missing sdio clock
ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers
Power: gpio-poweroff: Fix documentation and gpio_is_valid
ARM: Kirkwood: Fix missing clk for USB device.
arm: mvebu: Use dw-apb-uart instead of ns16650 as UART driver
Signed-off-by: Olof Johansson <olof@lixom.net>
I mismerged a previous branch from Alexander, and accidentally left
in ARCH_USES_GETTIMEOFFSET. Remove it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Alexander Shiyan <shc_work@mail.ru>
From Linus Walleij:
Two fixes to the Nomadik:
- Delete a dangling include
- Bump IRQ numbers to offset at 32
* tag 'nomadik-fixes-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: bump the IRQ numbers again
ARM: nomadik: delete dangling include
This fixes suspend to RAM adding necessary save and restore of L2 and GIC.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
When we fail to power down, we need to clear out the power request.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
With commit 384a290 (ARM: gic: use a private mapping for CPU target
interfaces), wake-up IPIs now go to all cores as the gic cpu interface
numbering may not follow core numbering. This broke secondary boot on
highbank since the boot address was already set for all secondary cores,
this caused all cores to boot before the kernel was ready.
Fix this by moving the setting of the jump address to
highbank_boot_secondary instead of highbank_smp_prepare_cpus and
highbank_cpu_die. Also, clear the address when we boot. This prevents
cores from booting before they are actually triggered and is also necessary
to get suspend/resume to work.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
With the addition of commit a0ae0240 (ARM: kernel: add device tree init
map function), the cpu reg values must match the cpu mpidr register or we'll
get warnings. For some reason, the CLUSTERID on highbank is 9, so the reg
value needs to be 0x90n to quiet the warnings.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
While device_type is considered deprecated, it is still needed for tools
like lshw to identify cpu nodes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The second FlexCAN port uses different clock than the first one, configure
correct clock to prevent hanging of the system during bringing up of the port.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The IRQ array must be terminated by -1 and not by -1+OMAP_INTC_START
This led to having a resource list of 100s of IRQs.
Looks like this was caused by commit a2cfc509 (ARM: OMAP3+: hwmod: Add
AM33XX HWMOD data) that probably had some search and replace updates
done for the patch for sparse irq support.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated wit information about the breaking commit]
Signed-off-by: Tony Lindgren <tony@atomide.com>
During merge of the mvebu patches a clock gate for pinctrl was
lost. This patch just readds the clock gate.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The use of writel instead of writel_relaxed lead to deadlock in some
situation (SMP on Armada 370 for instance). The use of writel_relaxed
as it was done in the rest of this driver fixes this bug.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes a bug for Aurora L2 cache controller when the
write-through mode is enable. For the clean operation even if we don't
have to flush the lines we still need to invalidate them.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If CONFIG_ARCH_MULTIPLATFORM & CONFIG_ARCH_MVEBU are both enabled,
__v7_pj4b_setup is added between __v7_ca9mp_setup and __v7_setup.
But there's no jump instruction added. If the chip is Cortex A5/A9,
it goes through __v7_pj4b_setup also. It results in system hang.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit 62e4d357a (ARM: 7609/1: disable errata work-arounds which access
secure registers) ARM_ERRATA_743622/751472 depends on !ARCH_MULTIPLATFORM.
Since imx has been converted to multiplatform, the following warning happens:
$ make imx_v6_v7_defconfig
warning: (SOC_IMX6Q && ARCH_TEGRA_2x_SOC && ARCH_TEGRA_3x_SOC) selects
ARM_ERRATA_751472 which has unmet direct dependencies (CPU_V7 &&
!ARCH_MULTIPLATFORM)
warning: (SOC_IMX6Q && ARCH_TEGRA_3x_SOC) selects ARM_ERRATA_743622
which has unmet direct dependencies (CPU_V7 && !ARCH_MULTIPLATFORM)
warning: (SOC_IMX6Q && ARCH_TEGRA_3x_SOC) selects ARM_ERRATA_743622
which has unmet direct dependencies (CPU_V7 && !ARCH_MULTIPLATFORM)
warning: (SOC_IMX6Q && ARCH_TEGRA_2x_SOC && ARCH_TEGRA_3x_SOC) selects
ARM_ERRATA_751472 which has unmet direct dependencies (CPU_V7 &&
!ARCH_MULTIPLATFORM)
Recommended approach is to remove ARM_ERRATA_743622/751472 from being selected
by SOC_IMX6Q and apply such workarounds into the bootloader.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Armada XP MV78230 DT include file is missing a ; at the
end of the cpu node.
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
We originally thought that the MV78230 variant of the Armada XP had
four Ethernet interfaces, like the other variants MV78260 and
MV78460. In fact, this is not true, and the MV78230 has only three
Ethernet interfaces.
So, the definitions of the Ethernet interfaces is now done as follows:
* armada-370-xp.dtsi: definitions of the first two interfaces, that
are common to Armada 370 and Armada XP
* armada-xp.dtsi: definition of the third interface, common to all
Armada XP variants.
* armada-xp-mv78260.dtsi and armada-xp-mv78460.dtsi: definition of
the fourth interface.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Contrary to our understanding at the time armada-xp-mv78230.dtsi was
written, the MV78230 variant of the Armada XP SoC has two cores and
not one. This patch updates the .dtsi file to take into account this
reality.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With the change to a DT based pinctrl/gpio driver, using gpio API
calls in board-*.c files no longer works, a dereferenced NULL pointer
exception occurs instead. By converting the GPIO code into a
fixed-regulator which gets probed later once pinctrl/gpio is
available, we avoid the exception.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mplch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
We moved to declaring clk gates in DT. However, device which do not
yet have a DT binding need to have a clkdev alias. This was missing
for SDIO.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mplch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Clock Management of kirkwood has moved to DT clock providers.
However, TWSI1 has not yet been done.
This switches TWSI1 of 88f6282 to DT clock providers.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Without the clock being held by a driver, it gets turned off at a bad
time causing the SoC to lockup. This is often during reboot.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The UART controller used in the Armada 370 and Armada XP SoCs is the
Synopsys DesignWare 8250 (aka Synopsys DesignWare ABP UART). The
improper use of the ns16550 can lead to a kernel oops during boot if
a character is sent to the UART before the initialization of the
driver. The DW APB has an extra interrupt that gets raised when
writing to the LCR when busy. This explains why we need to use
dw-apb-uart driver to handle this.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Since exynos5440 can support only common clk stuff, so this
patch skips legacy exynos5 clock initialization.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In the compatible field we should point the manufacturer of the board, which
in this case is Buglabs.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Here are the remaining __dev* removal patches against the 3.8-rc2 tree.
All of these patches were previously sent to the subsystem maintainers,
most of them were picked up and pushed to you, but there were a number
that fell through the cracks, and new drivers were added during the
merge window, so this series cleans up the rest of the instances of
these markings.
Third time's the charm...
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDmHOIACgkQMUfUDdst+ykTZgCePgK84Im3FFooEXJwaPbaf4ls
lO4AoMEDoWK+BHWOsjQwFPOwFFPEN2Xh
=6oAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core __dev* removal patches - take 3 - from Greg Kroah-Hartman:
"Here are the remaining __dev* removal patches against the 3.8-rc2
tree. All of these patches were previously sent to the subsystem
maintainers, most of them were picked up and pushed to you, but there
were a number that fell through the cracks, and new drivers were added
during the merge window, so this series cleans up the rest of the
instances of these markings.
Third time's the charm...
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflict with the pinctrl pull in pinctrl-sirf.c.
* tag 'driver-core-3.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (54 commits)
misc: remove __dev* attributes.
include: remove __dev* attributes.
Documentation: remove __dev* attributes.
Drivers: misc: remove __dev* attributes.
Drivers: block: remove __dev* attributes.
Drivers: bcma: remove __dev* attributes.
Drivers: char: remove __dev* attributes.
Drivers: clocksource: remove __dev* attributes.
Drivers: ssb: remove __dev* attributes.
Drivers: dma: remove __dev* attributes.
Drivers: gpu: remove __dev* attributes.
Drivers: infinband: remove __dev* attributes.
Drivers: memory: remove __dev* attributes.
Drivers: mmc: remove __dev* attributes.
Drivers: iommu: remove __dev* attributes.
Drivers: power: remove __dev* attributes.
Drivers: message: remove __dev* attributes.
Drivers: macintosh: remove __dev* attributes.
Drivers: mfd: remove __dev* attributes.
pstore: remove __dev* attributes.
...
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bump the IRQ numbers from offset at 1 (right above NO_IRQ)
to 32. This is the painful way to learn that if you're using
SPARSE_IRQ and avoid to define .nr_irqs in your machine,
the first 16 IRQs will be pre-allocated, and the IRQdomain
code (as the VIC core code before it) will then assume
that all IRQ descriptors are pre-allocated, and 16 of them
are - by somebody else. So mapping the IRQs will fail in
irq_create_mapping(). Moving the offset upward rids us of
this problem.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reference to the old include header for the FSMC NAND
MTD driver was somehow left in place, get rid of it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- i.MX5 register configuration
- Swap a kfree to devm_kfree() to avoid memory
corruption in the at91 driver
- Add the missing device tree binding doc for the
SIRF pin controller
- Enable the SIRF GPIO pull up/down configuration
from the device tree, it was previously retired
from the hard-coded approach.
- NULL check for the prcm_base in the Nomadik pin
controller.
- Provide the prcm_base from the device tree in the
DT boot path for the Nomadik pin controller.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJQ4tz9AAoJEEEQszewGV1z/7QQALIrLufIwjzpYwewQVB12kms
+gcjcv1sDhRmQOwhVuEbFwTzVgGmKBtLHSHX2fAQy61V5sc6xfypURUndvppIoIa
6s2qaIe464PkTXLH+60qtxF3/A6CqQ/S/B7fqL++Lls3Tt8ecTbox/Hpz5Mn0c7E
639X7xM/PdFMJyH9c/XL84u2XXWU+slJbnY0O5GLMW9zBrPzflNqUiW67XtfUsVJ
5PwH5fxw/SLxtIoXgTFzuTMSxAIvL5Wcbf3HnSV5I3R5awxKtvffqsTDxcZkWbSH
7OfNeqQCD1CD6Yft6L0xKXlOKUjB75Pn3OdmJxmG4nfm+wqYTuhqZDs9rj0QMXK2
iEDGCQsVLwxDUcbTX/AbxEZS4VUfSkYw6bLP0LpU05oGBCY4NNWgHu+ltIFl82zy
L6N7Tto9EhZGhJ+0VmlQaC3wqy1pJ8OUwJcPItQtrCLbYyoFTQuSRTPBFCMBDMoi
zmkIQxeRBLifUzNrfMjdtH7nz66qsisPxjsZtirus8OXZBPz3AjeLG0k+70CWHJ0
B9vurbHYzSukr8ZVbeJVJJ9XFts9VQlLkwxssVVieadnGtEmDAhNiy+etXyzaWa8
BBK887H+rkdPTNz51fYgEIgF41rcrOzvCDGoCdyforPSR8QMqDdfwafQA9V76XPA
M6Gy+m93wXDiTYAhI2kD
=ca6M
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"A first round of pinctrl fixes for v3.8:
- i.MX5 register configuration
- Swap a kfree to devm_kfree() to avoid memory corruption in the at91
driver
- Add the missing device tree binding doc for the SIRF pin controller
- Enable the SIRF GPIO pull up/down configuration from the device
tree, it was previously retired from the hard-coded approach.
- NULL check for the prcm_base in the Nomadik pin controller.
- Provide the prcm_base from the device tree in the DT boot path for
the Nomadik pin controller."
* tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
ARM: ux500: add pinctrl address resources
pinctrl: nomadik: return if prcm_base is NULL
pinctrl: sirf: enable GPIO pullup/down configuration from dts
pinctrl: sirf: add missing DT-binding document
pinctrl: fix comment mistake
drivers/pinctrl/pinctrl-at91.c: convert kfree to devm_kfree
pinctrl: imx5: fix GPIO_8 pad CAN1_RXCAN configuration
logs are available here:
http://www.pwsan.com/omap/testlogs/prcm_fixes_b_3.8-rc/20130102120724/
The 3730 Beagle XM here has an intermittent failure mounting SD root,
but the suspicion right now is that this is due to a failing SD card,
rather than any change introduced by these patches.
This second version includes a few changes requested by Tony Lindgren.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=oUTN
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-a2-for-v3.8-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.8-rc2/fixes
Some OMAP PRCM and sparse fixes against v3.8-rc1. A basic set of test
logs are available here:
http://www.pwsan.com/omap/testlogs/prcm_fixes_b_3.8-rc/20130102120724/
The 3730 Beagle XM here has an intermittent failure mounting SD root,
but the suspicion right now is that this is due to a failing SD card,
rather than any change introduced by these patches.
This second version includes a few changes requested by Tony Lindgren.
On OMAP2xxx chips, the register bitfields for the
PM_PWSTCTRL_*.POWERSTATE and PM_PWSTST_*.LASTSTATEENTERED are
different than those used on OMAP3/4. The order is reversed. So, for
example, on OMAP2xxx, 0x0 indicates 'ON'; but on OMAP3/4, 0x0
indicates 'OFF'. Similarly, on OMAP2xxx, 0x3 indicates 'OFF', but on
OMAP3/4, 0x3 indicates 'ON'.
To fix this, we treat the OMAP3/4 values as the powerdomain API
values, and create new low-level powerdomain functions for the
OMAP2xxx chips which translate between the OMAP2xxx values and the
OMAP3/4 values.
Without this patch, the conversion of the OMAP2xxx PM code to the
functional powerstate code results in a non-booting kernel.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The ETM/ETB drivers for OMAP3, enable the emu_src_ck clock in order
to access the ETM/ETB hardware. The emu_src_ck should enable the EMU
clock domain so that the ETM/ETB hardware is accessible. However,
currently when enabling the emu_src_ck the EMU clock domain is not
being enabled and so the ETM/ETB drivers are failing. Add enable/disable
clock functions to enable the EMU clock domain when enabling the
emu_src_ck.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
To read reset sources registers we have to use PRM_DEVICE_INST
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
RSTTIME is offset 0x8 and RSTST is offset 0x04 for OMAP4430 and
OMAP4460.
Signed-off-by: Nishanth Menon <nm@ti.com>
[ivan.khoronzhuk@ti.com: ported from k3.4]
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In the map for reset sources register we use defines intended for
using with PRM_RSTCTRL register. So fix it.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add DT support for twl4030_wdt. This is needed to get twl4030_wdt to
probe when booting with DT.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The VIC irqdomain code added in commit
07c9249f1f
"ARM: 7554/1: VIC: use irq_domain_add_simple()"
Had two bugs:
1) It didn't call irq_create_mapping() once on each
valid irq source in the slowpath when registering
the controller.
2) It passed a -1 as IRQ offset for the DT case, whereas
0 should be passed as invalid IRQ instead.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Versatile starts to register Linux IRQ numbers from offset 0
which is illegal, since this is NO_IRQ. Bump all hard-coded IRQs
by 32 to get rid of the problem.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
