DTO interrupt can be later than transmit interrupt(IDMAC) in case of
write. Current handling of IDMAC interrupt sets EVENT_DATA_COMPLETE as
well as EVENT_XFER_COMPLETE regardless of DTO rising. This makes the
current request finish in tasklet and permits the next request even
though current data transfer is still in progress. As a result, sequence
is broken and lock-up happens. Setting EVENT_DATA_COMPLETE is not proper
after IDMAC interrupt. It should be taken after DTO interrupt is
generated.
Reported-by: Dmitry Shmidt <dimitrysh@android.com>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Hyeonsu Kim <hyeonsu.kim@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDIO_CCCR_IF[1:0] in SDIO card is used for card data bus width
setting as below:
00b: 1-bit bus
01b: Reserved
10b: 4-bit bus
11b: 8-bit bus (only for embedded SDIO)
And sdio_enable_wide is for setting data bus width as 4-bit.
But currently, it first reads the register, second OR' 1b with
SDIO_CCCR_IF[1], and then writes it back.
As we can see, this is based on such assumption that the
SDIO_CCCR_IF[0] is always 0. Apparently, this is not right.
Signed-off-by: Yong Ding <yongd@marvell.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The use of DMA slave config operation requires that the burst size
(aka chunk size) is specified through this interface.
Modify atmel-mci slave driver to use this specification on its side.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The data timeout timer was configured after mmc_add_host call. So, with bad
timings, it was possible to have a mmc request causing mod_timer call on a
non setup timer.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
3bdc9ba892 ("mmc: use really long write timeout to deal with crappy
cards") in 3.4 increased the write timeout that the core sends to host
drivers to 3 seconds. This makes sdhci's "requested timeout too large"
warning trigger on every write; so, change this pr_warning() to a DBG().
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WeDQ
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc device tree conversions (part 2) from Olof Johansson:
"These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier."
Fix up trivial conflicts due to nearby changes in
drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: dt: tegra: invert status=disable vs status=okay
ARM: dt: tegra: consistent basic property ordering
ARM: dt: tegra: sort nodes based on bus order
ARM: dt: tegra: remove duplicate device_type property
ARM: dt: tegra: consistenly use lower-case for hex constants
ARM: dt: tegra: format regs properties consistently
ARM: dt: tegra: gpio comment cleanup
ARM: dt: tegra: remove unnecessary unit addresses
ARM: dt: tegra: whitespace cleanup
ARM: dt: tegra cardhu: fix typo in SDHCI node name
ARM: dt: tegra: cardhu: register core regulator tps62361
ARM: dt: tegra30.dtsi: Add SMMU node
ARM: dt: tegra20.dtsi: Add GART node
ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra: Add device tree support for AHB
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
...
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of the
samsung iommu code from a platform specific in-kernel interface to the
generic iommu subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hgkg
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc driver specific updates from Olof Johansson:
"These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of
the samsung iommu code from a platform specific in-kernel interface to
the generic iommu subsystem."
Fix up trivial conflicts in arch/arm/mach-exynos/Kconfig
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mmc: dt: Consolidate DT bindings
iommu/exynos: Add iommu driver for EXYNOS Platforms
ARM: davinci: optimize the DMA ISR
ARM: davinci: implement DEBUG_LL port choice
ARM: tegra: Add SMMU enabler in AHB
ARM: tegra: Add Tegra AHB driver
Input: pxa27x_keypad add choice to set direct_key_mask
Input: pxa27x_keypad direct key may be low active
Input: pxa27x_keypad bug fix for direct_key_mask
Input: pxa27x_keypad keep clock on as wakeup source
ARM: dt: tegra: pinmux changes for USB ULPI
ARM: tegra: add USB ULPI PHY reset GPIO to device tree
ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
ARM: tegra: change pll_p_out4's rate to 24MHz
ARM: tegra: fix pclk rate
ARM: tegra: reparent sclk to pll_c_out1
ARM: tegra: Add pllc clock init table
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
...
Drivers:
- at91-mci: This driver will be replaced by atmel-mci in 3.7.
- atmel-mci: Add support for old at91-mci hardware.
- dw_mmc: Allow multiple controllers; this previously caused corruption.
- imxmmc: Remove this driver, replaced by mxcmmc.
- mmci: Add device tree support.
- omap: Allow multiple controllers.
- omap_hsmmc: Auto CMD12, DDR support.
- tegra: Support SD 3.0 spec.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rjPa
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC changes from Chris Ball
- at91-mci: This driver will be replaced by atmel-mci in 3.7.
- atmel-mci: Add support for old at91-mci hardware.
- dw_mmc: Allow multiple controllers; this previously caused
corruption.
- imxmmc: Remove this driver, replaced by mxcmmc.
- mmci: Add device tree support.
- omap: Allow multiple controllers.
- omap_hsmmc: Auto CMD12, DDR support.
- tegra: Support SD 3.0 spec.
Fix up the usual trivial conflicts in feature-removal-schedule.txt
* tag 'mmc-merge-for-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (38 commits)
mmc: at91-mci: this driver is now deprecated
mmc: omap_hsmmc: pass IRQF_ONESHOT to request_threaded_irq
mmc: block: Allow disabling 512B sector size emulation
mmc: atmel-mci: add debug logs
mmc: atmel-mci: add support for version lower than v2xx
mmc: atmel-mci: change the state machine for compatibility with old IP
mmc: atmel-mci: the r/w proof capability lack was not well managed
mmc: dw_mmc: Fixed sdio interrupt mask bit setting bug
mmc: omap: convert to module_platform_driver
mmc: omap: make it behave well as a module
mmc: omap: convert to per instance workqueue
mmc: core: Remove dead code
mmc: card: Avoid null pointer dereference
mmc: core: Prevent eMMC VCC supply to be cut from late init
mmc: dw_mmc: make multiple instances of dw_mci_card_workqueue
mmc: queue: remove redundant memsets
mmc: queue: rename mmc_request function
mmc: core: skip card initialization if power class selection fails
mmc: core: fix the signaling 1.8V for HS200
mmc: core: fix the decision of HS200/DDR card-type
...
With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. but the payback comes later when adding
new boards can be done by only providing new device trees instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HIfz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
at91-mci is deprecated since atmel-mci can deal with all chips.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The flag of IRQF_ONESHOT should be passed to request_threaded_irq,
otherwise the following failure message should be dumped because
hardware handler is defined as NULL:
[ 3.383483] genirq: Threaded irq requested with handler=NULL and
!ONESHOT for irq 368
[ 3.392730] omap_hsmmc: probe of omap_hsmmc.0 failed with error -22
The patch fixes one kernel hang bug which is caused by mmc card
probe failure and root device can't be brought up.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Venkatraman S <svenkatr@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for large sector size of 4KB by disabling
emulation. This patch passes eMMC DATA_SECTOR_SIZE as the logical
block size during mmc_blk_alloc_req.
In order to use this patch for 4KB sector size, ensure that
USE_NATIVE_SECTOR is enabled, partition table is 4KB sector size
aligned and file system block and sector size are 4KB multiples.
Signed-off-by: Saugata Das <saugata.das@linaro.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The state machine use in atmel-mci can't work with old IP versions
(< 0x200). This patch allows to have a common state machine for all
versions in order to remove at91-mci driver only used for old versions.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
First mci IPs (mainly on rm9200 and 9261) don't have the r/w proof
capability. The driver didn't work correctly without this capability
in PDC mode because of the double buffer switch which is too slow
even if we stop the transfer to perform this switch.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sdio interrupt mask bits are arranged in [31:16].
(1 << SDMMC_INT_SDIO(slot->id))) does 16 bits left shift twice.
So this patch changes to do 16 bits left shift only one time.
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Acked-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Get rid of boilerplate code by using module_platform_driver macro,
no functional changes.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use proper __devinit and __devexit annotation for driver functions.
Instantiate the probe function for driver_ops instead of a probe in
the register function.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently, a global mmc_omap_wq is created for all instances of omap
hosts, which can lead to races and doesn't lend itself to unload the
module cleanly. Instead, create per instance workqueue and remove
the common workqueue.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'clk-next' of git://git.linaro.org/people/mturquette/linux:
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
ARM: Orion: SDIO: Add support for clk.
ARM: Orion: NAND: Add support for clk, if there is one.
ARM: Orion: EHCI: Add support for enabling clocks
ARM: Orion: SATA: Add per channel clk/clkdev support.
ARM: Orion: UART: Get the clock rate via clk_get_rate().
ARM: Orion: WDT: Add clk/clkdev support
ARM: Orion: Eth: Add clk/clkdev support.
ARM: Orion: SPI: Add clk/clkdev support.
ARM: Orion: Add clocks using the generic clk infrastructure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Changes in the dt2 branch move stuff around that gets changed
in the drivers/mmc branch. I chose a non-obvious resolution by
adding the new bus-width property into all the tegra sdhci device
nodes.
Conflicts:
arch/arm/boot/dts/tegra-cardhu.dts
arch/arm/boot/dts/tegra-harmony.dts
arch/arm/boot/dts/tegra-ventana.dts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* drivers/mmc:
mmc: dt: Consolidate DT bindings
Also pulls in the omap/dt-missed-3.4 branch as a dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch unifies the current DT MMC bindings documentation and code,
adds generic MMC DT bindings documentation, and updates .dts files for
consistency.
[cjb: typo fixes, addition of max-frequency property]
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/net/ethernet/freescale/fec.c
drivers/spi/spi-imx.c
drivers/tty/serial/imx.c
This resolves dependencies between the pinctrl and clock changes
in imx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Shawn Guo <shawn.guo@linaro.org> writes:
I chose to base it on Sascha's imx-common-clk series than -rc, because
otherwise it will keep patching clock file that has been removed by
imx-common-clk series. It also depends on imx-pinctrl pull-request
I just sent to be functional.
Note: when imx-common-clk and imx-pinctrl get merged together, the
following files will have conflicts. But the conflicts should not be
so hard to resolve.
[arnd: resolved those merge conflicts by pulling pinctrl branch]
* imx/dt: (24 commits)
ARM: dts: imx53-qsb: enable audio support
ARM: dts: imx51-babbage: enable audio support
ARM: imx: add audio codec clk lookup for imx53-qsb
ARM: imx: add audmux pad setting for imx51-babbage
ARM: imx: add more imx5 ssi clocks
ARM: dts: imx53-qsb: Add Dialog DA9053 PMIC support
ARM: dts: imx6q-sabrelite: add serial2 pinctrl support
ARM: dts: imx6q-sabrelite: add sound device imx6q-sabrelite-sgtl5000
ARM: imx6q_sabrelite: clk_register_clkdev cko1 for sgtl5000
ARM: imx6q: add ssi1_ipg clk_lookup
ARM: dts: imx6q-sabrelite: add audmux pinctrl support
ARM: dts: imx6q-sabrelite: add i2c1 pinctrl support
ARM: dts: imx6q-sabrelite: add audmux device
ARM: dts: imx6q-sabrelite: add ssi device
ARM: dts: imx6q-arm2: add pinctrl state for usdhc
ARM: imx6: Add UART2 for low-level debug
ARM: imx6q: register phy fixup only when CONFIG_PHYLIB is enabled
ARM: imx6q: move imx6q_sabrelite specific code to a dedicated function
ARM: dts: imx6q-sabrelite: Add SPI NOR support
ARM: dts: Add basic support for imx6q-sabresd
...
Pulls in imx/pinctrl and imx/clock as dependencies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'mxs/dt/for-3.5' of git://git.linaro.org/people/shawnguo/linux-2.6: (51 commits)
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
ARM: dts: enable mmc for imx23-evk
mmc: mxs-mmc: add device tree support
mmc: mxs-mmc: copy wp_gpio in struct mxs_mmc_host
mmc: mxs-mmc: have dma_channel than dma_res in mxs_mmc_host
mmc: mxs-mmc: use devm_* helper to make cleanup simpler
mmc: mxs-mmc: move header from mach into linux folder
mmc: mxs-mmc: get rid of the use of cpu_is_xxx
mmc: mxs-mmc: let ssp_is_old take host as parameter
mmc: mxs-mmc: use global stmp_device functionality
ARM: mxs: add gpio support for device tree boot
gpio/mxs: add device tree probe
gpio/mxs: get rid of the use of cpu_is_xxx
gpio/mxs: use devm_* helpers to make error handling simple
ARM: mxs: add mxs-dma dt support
ARM: mxs: do not add dma device by default
dma: mxs-dma: add device tree probe support
...
Copy wp_gpio from platform_data into struct mxs_mmc_host, so that
the use of platform_data can be limited in probe function, which
will ease the device tree probe.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
It replaces dma_res with dma_channel in struct mxs_mmc_host, so that
the device tree support will be a little easier, since dma channel
can not be retrieved from "struct resource *dma_res".
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
Use devm_request_and_ioremap and devm_request_irq helpers to clean up
the code a little bit.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
Rename arch/arm/mach-mxs/include/mach/mmc.h to
include/linux/mmc/mxs-mmc.h, so that mxs-mmc driver becomes
<mach/*> inclusion free.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
The register HW_SSP_VERSION is broken for ssp version detection,
as the address of the register is different between imx23 and imx28.
Let's use platform_device_id to detect the device, so that the use
of cpu_is_xxx can be removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Let macro ssp_is_old take host as parameter to make the code easy
to read.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Use global stmp_device functionality to reduce mach-dependency.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
This pull request updates the DaVinci SoC support to implement DEBUG_LL port
choice and optimizes the DMA ISR by removing unnecessary register reads.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=/we3
-----END PGP SIGNATURE-----
Merge tag 'v3.5-soc' of git://gitorious.org/linux-davinci/linux-davinci into next/drivers
DaVinci SoC updates for v3.5
This pull request updates the DaVinci SoC support to implement DEBUG_LL port
choice and optimizes the DMA ISR by removing unnecessary register reads.
* tag 'v3.5-soc' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: optimize the DMA ISR
ARM: davinci: implement DEBUG_LL port choice
+ sync with Linux 3.4-rc6
Signed-off-by: Olof Johansson <olof@lixom.net>
By Stephen Warren (30) and others
via Stephen Warren
* 'for-3.5/usb-ulpi' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (7 commits)
ARM: dt: tegra: pinmux changes for USB ULPI
ARM: tegra: add USB ULPI PHY reset GPIO to device tree
ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
ARM: tegra: change pll_p_out4's rate to 24MHz
ARM: tegra: fix pclk rate
ARM: tegra: reparent sclk to pll_c_out1
ARM: tegra: Add pllc clock init table
+ depends/pinctrl/mergebase branch
Pinctrl mergebase has a conflict in drivers/pinctrl/core.c that was resolved.
Signed-off-by: Olof Johansson <olof@lixom.net>
bus_width is passed to the function and when 0 (MMC_BUS_WIDTH_1)
will cause the function to return. So in in the second test it
definitely is different from 0, and the third test is redundant.
Signed-off-by: Philippe De Swert <philippedeswert@gmail.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
After the null check on md the code jumped to cmd_done, which then
will dereference md in mmc_blk_put. This patch avoids the possible
null pointer dereference in that case.
Signed-off-by: Philippe De Swert <philippedeswert@gmail.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For eMMC cards that has been initialized from a bootloader,
the VCC voltage supply must not be cut in an uncontrolled
manner, without first sending SLEEP or POWEROFF_NOTIFY.
The regulator_init_complete late initcall, may cut the VCC
regulator if it's reference counter is zero. To be able to
prevent the regulator from being cut, mmc_start_host, which
should execute at device init and thus before late init,
calls mmc_power_up. Then the host driver is able to increase
the reference to the regulator.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The variable 'dw_mci_card_workqueue' is a global variable shared between
multiple instances of the dw_mmc host controller. Due to this, data
corruption has been noticed when multiple instances of dw_mmc controllers
are actively reading/writing the media. Fix this by adding a instance
of 'struct workqueue_struct' for each host instance and removing the
global 'dw_mci_card_workqueue' instance.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Not needed to memset, as they are pointers and are assigned
to proper values in the next line anyway.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
