I/O pins on Tegra SoCs are grouped into so-called I/O pads. Each such
pad can be used to control the common voltage signal level and power
state of the pins in the given pad.
I/O pads can be powered down even if the system is active, which can
save power from that I/O interface. For SoC generations prior to
Tegra124 the I/O pad voltage is automatically detected and hence the
system software doesn't need to configure it. However, starting with
Tegra210 the detection logic has been removed, so explicit control of
the I/O pad voltage by system software is required.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Bit definitions are sorted in decreasing order by offset. Apply the same
ordering to all definitions.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The function tegra_pmc_readl() returns the u32 type data and hence
change the data type of variable where this data is stored to u32
type.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use BIT macro for register field definition and make constant as U
when using in shift operator like (3 << 30) to (3U << 30)
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra186 features a combination of Denver and Cortex-A57 CPU cores
and a GPU based on the Pascal architecture. It contains an ADSP with a
Cortex-A9 CPU used for audio processing, hardware video encoders and
decoders with multi-format support, ISP for image capture processing
and BPMP for power management.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
It was a bit surprising that the device was reported to have probed just
fine, but the provider hadn't been registered.
So handle any errors when registering the provider and fail the probe
accordingly.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The newly introduced pm_genpd_remove reverts the initialization done
by pm_genpd_init and is necessary in the error path of the rockchip
power-domain driver.
Without it the driver will in the error case cleanup the devm-allocated
structures including the elements referenced in the gpd_list thus making
deactivation of unused domains (and probably later genpd accesses as
well) fail by accessing invalid pointers.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add a driver for the Renesas R-Car Gen1 RESET/WDT and R-Car Gen2/Gen3
and RZ/G RST module.
For now this driver just provides an API to obtain the state of the mode
pins, as latched at reset time. As this is typically called from the
probe function of a clock driver, which can run much earlier than any
initcall, calling rcar_rst_read_mode_pins() just forces an early
initialization of the driver.
Despite the current simple and almost identical handling for all
supported SoCs, the driver matches against SoC-specific compatible
values, as the features provided by the hardware module differ a lot
across the various SoC families and members.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
In some cases, we have met the infinite loop in
rockchip_pmu_set_idle_request() or rockchip_do_pmu_set_power_domain().
As the crosbug.com/p/57351 reported, the boot hangs right after this
[1.629163] bootconsole [uart8250] disabled
[1.639286] [drm:drm_core_init] Initialized drm 1.1.0 20060810
[1.645926] [drm:drm_get_platform_dev] Initialized vgem 1.0.0 20120112..
[1.654558] iommu: Adding device ff8f0000.vop to group 0
[1.660569] iommu: Adding device ff900000.vop to group 1
<hang>
This patch adds the error message and timeout to avoid infinite loop if
it fails to get the ack.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add scpsys driver for MT2701.
mtk-scpsys now supports MT8173 (arm64) and MT2701 (arm). So it should
be enabled on both arm64 and arm platforms.
Signed-off-by: Shunli Wang <shunli.wang@mediatek.com>
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Refine scpsys driver common code to support multiple SoC / platform.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add support for RZ/G1M (R8A7743) SoC power areas to the R-Car SYSC driver.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On rk3288 it was important that powerdown and powerup counts for the
CPU/GPU in the kernel because:
* The power on default was crazy long.
* We couldn't rely on the firmware to set this up because really this
wasn't the firmware's job--the kernel was the only one that really
cared about bringing up / down CPUs and the GPU and doing suspend /
resume (which involves bringing up / down CPUs).
On newer ARM systems (like rk3399) ARM Trusted Firmware is in charge of
bringing up and down the CPUs and it really should be in charge of
setting all these counts right. After all ATF is in charge of suspend /
resume and CPU up / down. Let's get out of the way and let ATF do its
job.
A few other motivations for doing this:
* Depending on another configuration (PMU_24M_EN_CFG) these counts can
be either in 24M or 32k cycles. Thus, though ATF isn't really so
involved in bringing up the GPU, ATF should probably manage the counts
for everything so it can also manage the 24M / 32k choice.
* It turns out that (right now) 24M mode is broken on rk3399 and not
being used. That means that the count the kernel was programming
in (24) was not 1 us (which it seems was intended) but was actually
.75 ms
* On rk3399 there are actually 2 separate registers for setting CPU
up/down time plus 1 register for GPU up/down time. The curent kernel
code actually was putting the register for the "little" cores in the
"CPU" slot and the register for the "big" cores in the "GPU" slot. It
was never initting the GPU counts.
Note: this change assumes that ATF will actually set these values at
boot, as I'm proposing in <http://crosreview.com/372381>.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
[ATF change has landed]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Driver updates for ARM SoCs, including a couple of newly added drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for the
EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GvTq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for
the EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
bus: qcom-ebi2: depend on HAS_IOMEM
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
clocksource: exynos_mct: Add the support for ARM64
perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
bus: qcom: add EBI2 driver
bus: qcom: add EBI2 device tree bindings
rtc: rtc-pm8xxx: Add support for pm8018 rtc
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
soc: qcom: smd: Reset rx tail rather than tx
memory: atmel-sdramc: fix a possible NULL dereference
reset: hi6220: allow to compile test driver on other architectures
reset: zynq: add driver Kconfig option
reset: sunxi: add driver Kconfig option
reset: stm32: add driver Kconfig option
reset: socfpga: add driver Kconfig option
...
Enable the drivers on the powerpc arch.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Add self tests for the DPAA 1.x Queue Manager driver. The tests
ensure that the driver can properly enqueue and dequeue to/from
frame queues using the QMan portal infrastructure.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Add a self test for the DPAA 1.x Buffer Manager driver. This
test ensures that the driver can properly acquire and release
buffers using the BMan portal infrastructure.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
This driver enables the Freescale DPAA 1.x Queue Manager block.
QMan is a hardware accelerator that manages frame queues. It allows
CPUs and other accelerators connected to the SoC datapath to enqueue
and dequeue ethernet frames, thus providing the infrastructure for
data exchange among CPUs and datapath accelerators.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
This driver enables the Freescale DPAA 1.x Buffer Manager block.
BMan is a hardware accelerator that manages buffer pools. It allows
CPUs and other accelerators connected to the SoC datapath to acquire
and release buffers during data processing.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
of_mm_gpiochip_add_data() calls mm_gc->save_regs() before
setting the data. Therefore ->save_regs() cannot use
gpiochip_get_data()
An Oops is encountered without this fix.
fixes: 1e714e54b5 ("powerpc: qe_lib-gpio: use gpiochip data pointer")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: <stable@vger.kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Scott Wood <oss@buserror.net>
Commit 0e6e01ff69 ("CPM/QE: use genalloc to manage CPM/QE muram")
has changed the way muram is managed.
genalloc uses kmalloc(), hence requires the SLAB to be up and running.
On powerpc 8xx, cpm_reset() is called early during startup.
cpm_reset() then calls cpm_muram_init() before SLAB is available,
hence the following Oops.
cpm_reset() cannot be called during initcalls because the CPM is
needed for console.
This patch removes the call to cpm_muram_init() from cpm_reset().
cpm_muram_init() will be called from a new function called cpm_init()
which is declared as subsys_initcall, unless cpm_muram_alloc() is
called earlier for the serial console in which case cpm_muram_init()
will be called from there.
The reason for calling it from two places is that some drivers
(e.g. i2c-cpm) need some of the initialisations done by
cpm_muram_init() but don't call cpm_muram_alloc(). The console
driver calls cpm_muram_alloc() but some platforms might not use
the CPM serial ports for console.
[ 0.000000] Unable to handle kernel paging request for data at address 0x00000008
[ 0.000000] Faulting instruction address: 0xc01acce0
[ 0.000000] Oops: Kernel access of bad area, sig: 11 [#1]
[ 0.000000] PREEMPT CMPC885
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.4.14-g0886ed8 #5
[ 0.000000] task: c05183e0 ti: c0536000 task.ti: c0536000
[ 0.000000] NIP: c01acce0 LR: c0011068 CTR: 00000000
[ 0.000000] REGS: c0537e50 TRAP: 0300 Not tainted (4.4.14-s3k-dev-g0886ed8-svn)
[ 0.000000] MSR: 00001032 <ME,IR,DR,RI> CR: 28044428 XER: 00000000
[ 0.000000] DAR: 00000008 DSISR: c0000000
GPR00: c0011068 c0537f00 c05183e0 00000000 00009000 ffffffff 00000bc0 ffffffff
GPR08: ff003000 ff00b000 ff003bbf 00000000 22044422 100d43a8 00000000 07ff94e8
GPR16: 00000000 07bb5d70 00000000 07ff81f4 07ff81f4 07ff81f4 00000000 00000000
GPR24: 07ffb3a0 07fe7628 c0550000 c7ffa190 c0540000 ff003bbf 00000000 00000001
[ 0.000000] NIP [c01acce0] gen_pool_add_virt+0x14/0xdc
[ 0.000000] LR [c0011068] cpm_muram_init+0xd4/0x18c
[ 0.000000] Call Trace:
[ 0.000000] [c0537f00] [00000200] 0x200 (unreliable)
[ 0.000000] [c0537f20] [c0011068] cpm_muram_init+0xd4/0x18c
[ 0.000000] [c0537f70] [c0494684] cpm_reset+0xb4/0xc8
[ 0.000000] [c0537f90] [c0494c64] cmpc885_setup_arch+0x10/0x30
[ 0.000000] [c0537fa0] [c0493cd4] setup_arch+0x130/0x168
[ 0.000000] [c0537fb0] [c04906bc] start_kernel+0x88/0x380
[ 0.000000] [c0537ff0] [c0002224] start_here+0x38/0x98
[ 0.000000] Instruction dump:
[ 0.000000] 91430010 91430014 80010014 83e1000c 7c0803a6 38210010 4e800020 7c0802a6
[ 0.000000] 9421ffe0 bf61000c 90010024 7c7e1b78 <80630008> 7c9c2378 7cc31c30 3863001f
[ 0.000000] ---[ end trace dc8fa200cb88537f ]---
fixes: 0e6e01ff69 ("CPM/QE: use genalloc to manage CPM/QE muram")
Cc: stable@vger.linux.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[scottwood: Removed some string changes unrelated to bugfix]
Signed-off-by: Scott Wood <oss@buserror.net>
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2;
statement S2,S1;
@@
- if (of_get_property(e1,e2,NULL))
+ if (of_property_read_bool(e1,e2))
S1 else S2
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
modify get_qe_base function with of_address_to_resource
instead of of_get_property and of_translate_address.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Use the function resource_size instead of explicit computation.
Problem found using Coccinelle.
Signed-off-by: Vaishali Thakkar <vaishali.thakkar@oracle.com>
Signed-off-by: Scott Wood <oss@buserror.net>
reduces the failure rate on the data transfer between pmic and
pmic wrapper.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=qdYG
-----END PGP SIGNATURE-----
Merge tag 'v4.8-next-soc' of https://github.com/mbgg/linux-mediatek into next/drivers
Pull "ARM: mediatek: soc updates for v4.9" from Matthias Brugger:
extent the waiting time of the pmic wrapper to 10 ms which
reduces the failure rate on the data transfer between pmic and
pmic wrapper.
* tag 'v4.8-next-soc' of https://github.com/mbgg/linux-mediatek:
soc: mediatek: PMIC wrap: Extend the waiting time to 10ms.
This contains a single patch to fix an issue with setting the deep power
down mode of I/O rails.
-----BEGIN PGP SIGNATURE-----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=IFfY
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.9-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Pull "soc/tegra: Changes for v4.9-rc1" from Thierry Reding:
This contains a single patch to fix an issue with setting the deep power
down mode of I/O rails.
* tag 'tegra-for-4.9-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Fix incorrect DPD request
Update the EXYNOS PM domain code to use the of_genpd_add_subdomain()
and remove any calls to of_genpd_get_from_provider().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The local end of each SMD channel is responsible for updating the tx
head and the rx tail, as such we should not touch the tx tail during a
reset.
Reported-by: Jeremy McNicoll <jmcnicol@redhat.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
By representing each edge as its own device the channels are no longer
tied to being parented by the same smd device and as such an edge can
live as children of e.g. remoteproc instances.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The code exectued by the interrupt handler depends on the values parsed
after requesting the irq, just to be save we should therefor move the
request_irq() call to be done after parsing the properties.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Multi-channel clients split between several drivers need a way to close
individual channels, as these drivers might be removed individually.
With this in place the responsibility of closing additionally opened
channels to the client as well only concerning smd about the primary
channel.
With this approach we will only trigger removal of SMD devices based on
the state of the primary channel, however we get in sync with how rpmsg
works.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
If we fail to get the hwspinlock due to probe defer, we shouldn't
print an error message. Just be silent in this case.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Read data fails sometimes because of a timeout that PMIC cannot transfer data
to PMIC wrap on time, extend the waiting time to 10ms to reduce the failed
rate.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Register gpd_dev_ops.active_wakeup function to support keep power
during suspend state. And add flag to each power domain to
decide whether keep power during suspend or not.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reading the DPD_REQ & DPD2_REQ registers returns the previous requests.
If we sets the current request bit with the returned value, then other
pads will be turned on or off unexpectedly.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
1. Fix size of allocation for Exynos SROM registers (too much was allocated).
2. Constify fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7gEy
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-4.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/drivers
Merge "Samsung drivers/soc update for v4.8, part 3" into next/drivers:
1. Fix size of allocation for Exynos SROM registers (too much was allocated).
2. Constify fix.
* tag 'samsung-drivers-4.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
soc: samsung: pmu: Constify arrays with PMU data
memory: samsung: exynos-srom: Fix wrong count of registers
of machine-local files and boardfile-type data for regulators
and ASoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VLJl
-----END PGP SIGNATURE-----
Merge tag 'ux500-cleanup-bundle' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/drivers
Merge "Ux500 cleanups from Arnd" from Linus Walleij:
This is a set of cleanups for the Ux500 that reduce the number
of machine-local files and boardfile-type data for regulators
and ASoC.
* tag 'ux500-cleanup-bundle' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
As the ux500 id code is basically a standalone driver, we can move it
out of the arch code into drivers/soc/ux500.
This is a user-visible change, as it moves all the devices in sysfs
from /sys/devices/soc0/ to /sys/devices/ and leaves the soc0 node as a
separate device.
Originally the idea was to put all on-chip devices under the soc node,
and ux500 was the first platform to have this device, but later platforms
almost all didn't follow that pattern, so this makes the platform do
the same thing as everyone else.
Since the platform is really obsolete now, I am optimistic that nothing
will break after moving the devices around.
As the SoC driver no longer has access to the private header files,
I'm changing the code to instead look up the address of the backupram
from devicetree, which is a good idea anyway.
Finally, having a separate Kconfig symbol means the driver is now
optional and could even be a loadable module rather than always being
built-in if we allowed that for soc_device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[Fixup mising Makefile, fixup BB_UID_BASE to fc0]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We get a harmless warning if the RASPBERRYPI_POWER driver is enabled without
CONFIG_OF during compile testing:
warning: RASPBERRYPI_POWER selects PM_GENERIC_DOMAINS_OF which has unmet direct dependencies (PM_GENERIC_DOMAINS && OF)
There is no need to select PM_GENERIC_DOMAINS_OF if OF is set, so we can
replace the 'select' with a dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Eric Anholt <eric@anholt.net>
Contains fixes and cleanups to the PMC driver, as well as some fixes for
the generic PM domain support and some prep work to support PCIe on 64-
bit ARM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=eFoM
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.8-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
soc/tegra: Changes for v4.8-rc1
Contains fixes and cleanups to the PMC driver, as well as some fixes for
the generic PM domain support and some prep work to support PCIe on 64-
bit ARM.
* tag 'tegra-for-4.8-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: Stub out PCIe IRQ workaround on 64-bit ARM
soc/tegra: pmc: Enable XUSB partitions on boot
soc/tegra: pmc: Initialise power partitions early
soc/tegra: pmc: Add specific error messages
soc/tegra: pmc: Use whitespace more consistently
soc/tegra: pmc: Don't probe PMC if early initialisation fails
soc/tegra: pmc: Add missing of_node_put()
soc/tegra: pmc: Ensure mutex is always initialised
soc/tegra: pmc: Don't populate SoC data until register space is mapped
soc/tegra: pmc: Fix early initialisation of PMC
soc/tegra: pmc: Ensure powergate is available when powering on
soc/tegra: pmc: Initialise resets associated with a power partition
soc/tegra: pmc: Use register definitions instead of magic values
Signed-off-by: Olof Johansson <olof@lixom.net>
* Prepare for handling SYSC interrupt configuration purely
from DT in the rcar-sysc driver for new SoCs, while preserving
backward compatibility with old DTBs for R-Car H1, H2, and M2-W
* Add R8A7792 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/p9r
-----END PGP SIGNATURE-----
Merge tag 'renesas-rcar-sysc2-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
Second Round of Renesas ARM Based SoC R-Car SYSC Updates for v4.8
* Prepare for handling SYSC interrupt configuration purely
from DT in the rcar-sysc driver for new SoCs, while preserving
backward compatibility with old DTBs for R-Car H1, H2, and M2-W
* Add R8A7792 support
* tag 'renesas-rcar-sysc2-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
soc: renesas: rcar-sysc: Improve SYSC interrupt config in legacy wrapper
soc: renesas: rcar-sysc: Move SYSC interrupt config to rcar-sysc driver
soc: renesas: rcar-sysc: Make rcar_sysc_init() init the PM domains
soc: renesas: rcar-sysc: Fix uninitialized error code in rcar_sysc_pd_init()
soc: renesas: rcar-sysc: add R8A7792 support
Signed-off-by: Olof Johansson <olof@lixom.net>
* Rework of SCM driver
* Add file patterns for Qualcomm Maintainers entry
* Add worker for wcnss_ctrl signaling
* Fixes for smp2p
* Update smem_state properties to match documentation
* Add SCM Peripheral Authentication service
* Expose SCM PAS command 10 as a reset controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WprH
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/drivers
Qualcomm ARM Based Driver Updates for v4.8
* Rework of SCM driver
* Add file patterns for Qualcomm Maintainers entry
* Add worker for wcnss_ctrl signaling
* Fixes for smp2p
* Update smem_state properties to match documentation
* Add SCM Peripheral Authentication service
* Expose SCM PAS command 10 as a reset controller
* tag 'qcom-drivers-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
firmware: qcom: scm: Expose PAS command 10 as reset-controller
firmware: qcom: scm: Peripheral Authentication Service
soc: qcom: Update properties for smem state referencing
soc: qcom: smp2p: Drop io-accessors
soc: qcom: smp2p: Correct addressing of outgoing value
soc: qcom: wcnss_ctrl: Make wcnss_ctrl parent the other components
firmware: qcom: scm: Add support for ARM64 SoCs
firmware: qcom: scm: Convert to streaming DMA APIS
firmware: qcom: scm: Generalize shared error map
firmware: qcom: scm: Use atomic SCM for cold boot
firmware: qcom: scm: Convert SCM to platform driver
MAINTAINERS: Add file patterns for qcom device tree bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
The Tegra XHCI driver does not currently manage the Tegra XUSB power
partitions and so it these partitions have not been enabled by the
bootloader then the system will crash when probing the XHCI device.
While proper support for managing the power partitions is being
developed to the XHCI driver for Tegra, for now power on all the XUSB
partitions for USB host and super-speed on boot if the XHCI driver is
enabled.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If CONFIG_PM_GENERIC_DOMAINS is not enabled, then power partitions
associated with a device will not be enabled automatically by the PM
core when the device is in use. To avoid situations where a device in
a power partition is to be used but the partition is not enabled,
initialise the power partitions for Tegra early in the boot process and
if CONFIG_PM_GENERIC_DOMAINS is not enabled, then power on all
partitions defined in the device-tree blob.
Note that if CONFIG_PM_GENERIC_DOMAINS is not enabled, after the
partitions are turned on, the clocks and resets used as part of the
sequence for turning on the partition are released again as they are no
longer needed by the PMC driver. Another benefit of this is that this
avoids any issues of sharing resets between the PMC driver and other
device drivers that may wish to independently control a particular
reset.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When initialising a powergate, only a single error message is shown if
the initialisation fails. Add more error messages to give specific
details of what failed if the initialisation failed and remove the
generic failure message.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit 0259f522e0 ('soc/tegra: pmc: Restore base address on probe
failure') fixes an issue where the PMC base address pointer is not
restored on probe failure. However, this fix creates another problem
where if early initialisation of the PMC driver fails and an initial
mapping for the PMC address space is not created, then when the PMC
device is probed, the PMC base address pointer will not be valid and
this will cause a crash when tegra_pmc_init() is called and attempts
to access a register.
Although the PMC address space is mapped a 2nd time during the probe
and so this could be fixed by populating the base address pointer
earlier during the probe, this adds more complexity to the code.
Moreover, the PMC probe also assumes the the soc data pointer is also
initialised when the device is probed and if not will also lead to a
crash when calling tegra_pmc_init_tsense_reset(). Given that if the
early initialisation does fail then something bad has happen, it seems
acceptable to allow the PMC device probe to fail as well. Therefore, if
the PMC base address pointer or soc data pointer are not valid when
probing the PMC device, WARN and return an error.
Fixes: 0259f522e0 ('soc/tegra: pmc: Restore base address on probe failure')
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add missing of_node_put() in PMC early initialisation function to avoid
leaking the device nodes.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
[treding@nvidia.com: squash in a couple more of_node_put() calls]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The mutex used by the PMC driver may not be initialised if early
initialisation of the driver fails. If this does happen, then it could
be possible for callers of the public PMC functions to still attempt to
acquire the mutex. Fix this by initialising the mutex as soon as
possible to ensure it will always be initialised.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The public functions exported by the PMC driver use the presence of the
SoC data pointer to determine if the PMC device is configured and the
registers can be accessed. However, the SoC data is populated before the
PMC register space is mapped and this opens a window where the SoC data
pointer is valid but the register space has not yet been mapped which
could lead to a crash. Furthermore, if the mapping of the PMC register
space fails, then the SoC data pointer is not cleared and so would
expose a larger window where a crash could occur.
Fix this by initialising the SoC data pointer after the PMC register
space has been mapped.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
During early initialisation, the available power partitions for a given
device is configured as well as the polarity of the PMC interrupt. Both
of which should only be configured if there is a valid device node for
the PMC device. This is because the soc data used for configuring the
power partitions is only available if a device node for the PMC is found
and the code to configure the interrupt polarity uses the device node
pointer directly.
Some early device-tree images may not have this device node and so fix
this by ensuring the device node pointer is valid when configuring these
items.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The function tegra_power_sequence_power_up() is a public function used
to power on a partition. When this function is called, we do not check
to see if the partition being powered up is valid/available. Fix this
by checking to see that the partition is valid/available.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When registering the Tegra power partitions with the generic PM domain
framework, the current state of the each partition is checked and used
as the default state for the partition. However, the state of each reset
associated with the partition is not initialised and so it is possible
that the state of the resets are not in the expected state. For example,
if a partition is on, then the resets should be de-asserted and if the
partition is off, the resets should be asserted.
There have been cases where the bootloader has powered on a partition
and only de-asserted some of the resets to some of the devices in the
partition. This can cause accesses to these devices to hang the system
when the kernel boots and attempts to probe these devices.
Ideally, the driver for the device should ensure the reset has been
de-asserted when probing, but the resets cannot be shared between the
PMC driver (that needs to de-assert/assert the reset when turning the
partition on or off) and another driver because we cannot ensure the
reset is in the correct state.
To ensure the resets are in the correct state, when using the generic
PM domain framework, put each reset associated with the partition in
the correct state (based upon the partition's current state) when
obtaining the resets for a partition.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Align SYSC interrupt configuration in the legacy wrapper with the DT
version:
- Mask SYSC interrupt sources before enabling them (doesn't matter
much as they're disabled at the GIC level anyway),
- Make sure not to clear reserved SYSCIMR bits that were set before.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On R-Car H1 and Gen2, the SYSC interrupt registers are always configured
using hardcoded values in platform code. For R-Car Gen2, values are
provided for H2 and M2-W only, other SoCs are not yet supported, and
never will be.
Move this configuration from SoC-specific platform code to the
rcar_sysc_init() wrapper, so it can be skipped if the SYSC is configured
from DT. This would be the case not only for H1, H2, and M2-W using a
modern DTS, but also for other R-Car Gen2 SoCs not supported by the
platform code, relying purely on DT.
There is no longer a need to return the mapped register block, hence
make the function return void.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Let rcar_sysc_init() trigger initialization of the SYSC PM domains from
DT if called before the early_initcall.
On failure, it falls back to mapping the passed register block, as
before.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On success, rcar_sysc_pd_init() returns an uninitialized error code.
Use the return value of of_genpd_add_provider_onecell() to fix this.
This went unnoticed, as early_initcall() doesn't care about the return
value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the property names to match device tree bindings, the correct
values should be qcom,smem-states and qcom,smem-state-names.
Also update the #qcom,smem-state-cells for consistency, before we merge
any users of these properties.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
SMEM is now mapped write-combine and we can use memcpy to access the
name of the entires.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The valid_entries index should not be incremented until after we have
acquired the pointer to the value, or we will read and write data one
item off.
Fixes: 50e9964141 ("soc: qcom: smp2p: Qualcomm Shared Memory Point to Point")
Cc: stable@vger.kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
We need the signal from wcnss_ctrl indicating that the firmware is up
and running before we can communicate with the other components of the
chip. So make these other components children of the wcnss_ctrl device,
so they can be probed in order.
The process seems to take between 1/2-5 seconds, so this is done in a
worker, instead of holding up the probe.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
- Florian moves drivers/soc/brcmstb to drivers/soc/bcm/brcmstb to be consistent with
how other SoCs are doing it
- Chris provides a reset driver which is common to the BCM21664 and BCM23550 SoCs
- Ben fixes a warning by providing the appropriate include file
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXY1WaAAoJEIfQlpxEBwcErVMQAK9dNwq7Zul5NPc+QXe/0vUy
hLzjF2qm8CEqxU+YF3B1OSI4DHFEdJi3kgDq0RwaVoNC11nFdD5CQIKiB2a0O4jL
HYlRSir2BoeuSdt/IUry8tdUJOy1LhK/OM0yu/E4OJq/yHgimM/D2+kh6ToSS23s
X2rocyat7CUAqtiEXroYmWgu+UbUI9Dst+WtXJ4bL6iJe5asZPeTFdxNuMmO0RBF
XcGY7nmOD420jhYJvZkZUibo/tz/i57Ar2i0SFpTgQGQ1DHbmyhEFCbOm6QuZ3J0
l5deISy0buXfTTc15n9zhoqZxtGiM3ExqEhrTdvaSjBkZrZUUhjKo+ED5yGJ7Yqy
2cRP1dua4ixEbOJoAU+IuoqDj42zOxpOLhwNi7e8ROTqXfxHxAVizPJ6dKZKP1vz
6KqqJtEoD+U9mrylAQ55+D68e1kNy7r8TN4qJBhrNSO3G2bWogYzUKHFMdSPyNFY
/g0qhAwBrvPHw1ieezS74uMCIF525QfylpcX4MP0s48fAN32SQPdFb5mZuxzqvVH
V0Z/VShkndLkoslChEZ5intuvMDUMyP1tdwvthuvoJQOVh59Fede+7TG+wsxzOGP
FbWGhtWzxVzKLOvwBZhLMv5VwPH7rFSSTuc3tT2xMtpoMy/lhRabH/nqQKdm9CET
uzRJ8hDFy3oWx3L95nA/
=gNzd
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.8/drivers' of http://github.com/Broadcom/stblinux into next/drivers
This pull request contains drivers related changes for Broadcom SoCs:
- Florian moves drivers/soc/brcmstb to drivers/soc/bcm/brcmstb to be consistent with
how other SoCs are doing it
- Chris provides a reset driver which is common to the BCM21664 and BCM23550 SoCs
- Ben fixes a warning by providing the appropriate include file
* tag 'arm-soc/for-4.8/drivers' of http://github.com/Broadcom/stblinux:
soc: brcmstb: fix warning from missing include
power: Introduce Broadcom kona reset driver
soc: Move brcmstb to bcm/brcmstb
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for R-Car V2H (R8A7792) SoC power areas to the SYSC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use register definitions for the main SoC reset operation instead of
hard-coding magic values. Note that the PMC_RST_STATUS register isn't
actually accessed, but since it is mentioned in a comment the
definitions are added for completeness.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
QE has module to support TDM, some other protocols
supported by QE are based on TDM.
add a qe-tdm lib, this lib provides functions to the protocols
using TDM to configurate QE-TDM.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tdm clock configuration in both qe clock system and ucc
fast controller.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx_sync and tx_sync are used by QE-TDM mode,
add them to struct ucc_fast_info.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The brcmstb_biuctrl_init() is defined in the soc specific header
file, but wasn't included in the driver file. Fix the following
warning by including <linux/soc/brcmstb/brcmstb.h> in the driver:
drivers/soc/brcmstb/biuctrl.c:101:13: warning: symbol 'brcmstb_biuctrl_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Unify the different Broadcom SoCs directory and have everybody live
under drivers/soc/bcm/*.
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Introduce a platform selectable symbol EXYNOS_PM_DOMAINS which can be
also toggled on by COMPILE_TEST for some build coverage.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The ARMv8 Exynos family (Exynos5433 and Exynos7420) uses different value
(0xf instead of 0x7) for controlling the power domain on/off registers
(both for control and for status).
Choose the value depending on the compatible. This prepares the driver
for supporting ARMv8 SoCs.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Exynos PM domains driver does not have mach-specific dependencies so it
can be safely moved out of arm/mach-exynos to drivers/soc. This in
future will allow re-using it on ARM64 boards.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
On ARM64, the mtk-pmic-wrap driver causes a harmless warning:
mtk-pmic-wrap.c:1062:16: warning: large integer implicitly truncated to unsigned type [-Woverflow]
mtk-pmic-wrap.c:1074:16: warning: large integer implicitly truncated to unsigned type [-Woverflow]
mtk-pmic-wrap.c:1086:16: warning: large integer implicitly truncated to unsigned type [-Woverflow]
.int_en_all = ~(BIT(31) | BIT(1)),
The problem is that the result of the BIT() macro is an 'unsigned long',
so taking the bitwise NOT operation of that results in an integer
with the upper 32 bits all set and that cannot be assigned to a
'u32' variable without loss of information.
This is harmless because we were never interested in the upper bits
here anyway, so we can shut up the warning by adding a simple cast
to 'u32'.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons. For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to
get done.
Finally, reset controller handling as always gets merged through here
as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=x+iD
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons.
For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to get
done.
Finally, reset controller handling as always gets merged through here
as well"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
arm-ccn: Enable building as module
soc/tegra: pmc: Add generic PM domain support
usb: xhci: tegra: Add Tegra210 support
usb: xhci: Add NVIDIA Tegra XUSB controller driver
dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
PCI: tegra: Support per-lane PHYs
dt-bindings: pci: tegra: Update for per-lane PHYs
phy: tegra: Add Tegra210 support
phy: Add Tegra XUSB pad controller support
dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
phy: core: Allow children node to be overridden
clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
drivers: firmware: psci: make two helper functions inline
soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
...
These are all the updates to device tree files for 32-bit platforms,
which as usual makes up the bulk of the ARM SoC changes: 462 non-merge
changesets, 450 files changed, 23340 insertions, 5216 deletions.
The three platforms that are added with the "soc" branch are here as well,
and we add some related machine files:
- For Aspeed AST2400/AST2500, we get the evaluation platform and
the Tyan Palmetto POWER8 mainboard that uses the AST2400 BMC
- For Oxnas 810SE, the Western Digital "My Book World Edition"
is added as the only platform at the moment.
- For ARM MPS2, the AN385 (Cortex-M3) and AN399 (Cortex-M7)
are supported
On the ARM Realview development platform, we now support all machines
with device tree, previously only the board files were supported, which
in turn will likely be removed soon.
Qualcomm IPQ4019 is the second generation ARM based "Internet Processor",
following the IPQ806x that is used in many high-end WiFi routers. This one
integrates two ath10k wifi radios that were previously on separate chips.
Other boards that got added for existing chips are:
- On Ti OMAP family:
- Amazon Kindle Fire, first generation, tablet and ebook reader
- OnRISC Baltos iR 2110 and 3220 embedded industrial PCs
- TI AM5728 IDK, TI AM3359 ICE-V2, and TI DRA722 Rev C EVM
development systems
- On Samsung EXYNOS platform:
- Samsung ARTIK5 evaluation board, see
https://www.artik.io/modules/overview/artik-5/
- On NXP i.MX platforms:
- Ka-Ro electronics TX6S-8034, TX6S-8035, TX6U-8033, TX6U-81xx,
TX6Q-1036, TX6Q-1110/-1130, TXUL-0010 and TXUL-0011 industrial
SoM modules
- Embest MarS Board i.MX6Dual DIY platform
- Boundary Devices i.MX6 Quad Plus Nitrogen6_MAX and
SoloX Nitrogen6sx embedded boards
- Technexion Pico i.MX6UL compute module
- ZII VF610 Development Board
- On Marvell embedded (mvebu, orion, kirkwood) platforms:
- Linksys Viper (E4200v2 / EA4500) WiFi router
- Buffalo Kurobox Pro NAS
- On Qualcomm Snapdragon:
- Arrow DragonBoard 600c (96boards) with APQ8064 Snapdragon 600
- On Rockchips platform:
- mqmaker MiQi single-board computer
- On Altera SoCFPGA:
- samtec VIN|ING 1000 vehicle communication interface
- On Allwinner Sunxi platforms:
- Dserve DSRV9703C tablet
- Difrnce DIT4350 tablet
- Colorfly E708 Q1 tablet
- Polaroid MID2809PXE04 tablet
- Olimex A20 OLinuXino LIME2 single board computer
- Xunlong Orange Pi 2, Orange Pi One, and Orange Pi PC
single board computers
Across many platforms, bug fixes went in to address warnings that
dtc now emits with 'make dtbs W=1'. Further changes for device enablement
went into Ti OMAP, bcm283x (Raspberry Pi), bcm47xx (wifi router),
Ti Davinci, Samsung EXYNOS, Marvell mvebu/kirkwood/orion, NXP i.MX/Vybrid
NXP LPC18xx, NXP LPC32xx, Renesas shmobile/r-mobile/r-car, Rockchips
rk3xxx, ST Ux500, ST STi, Atmel AT91/SAMA5, Altera SoCFPGA, Allwinner
Sunxi, Sigma Designs Tango, NVIDIA Tegra, Socionext Uniphier and ARM
Versatile Express.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Nx46
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"These are all the updates to device tree files for 32-bit platforms,
which as usual makes up the bulk of the ARM SoC changes: 462 non-merge
changesets, 450 files changed, 23340 insertions, 5216 deletions.
The three platforms that are added with the "soc" branch are here as
well, and we add some related machine files:
- For Aspeed AST2400/AST2500, we get the evaluation platform and the
Tyan Palmetto POWER8 mainboard that uses the AST2400 BMC
- For Oxnas 810SE, the Western Digital "My Book World Edition" is
added as the only platform at the moment.
- For ARM MPS2, the AN385 (Cortex-M3) and AN399 (Cortex-M7) are
supported
On the ARM Realview development platform, we now support all machines
with device tree, previously only the board files were supported,
which in turn will likely be removed soon.
Qualcomm IPQ4019 is the second generation ARM based "Internet
Processor", following the IPQ806x that is used in many high-end WiFi
routers. This one integrates two ath10k wifi radios that were
previously on separate chips.
Other boards that got added for existing chips are:
Ti OMAP family:
- Amazon Kindle Fire, first generation, tablet and ebook reader
- OnRISC Baltos iR 2110 and 3220 embedded industrial PCs
- TI AM5728 IDK, TI AM3359 ICE-V2, and TI DRA722 Rev C EVM
development systems
Samsung EXYNOS platform:
- Samsung ARTIK5 evaluation board, see
https://www.artik.io/modules/overview/artik-5/
NXP i.MX platforms:
- Ka-Ro electronics TX6S-8034, TX6S-8035, TX6U-8033, TX6U-81xx,
TX6Q-1036, TX6Q-1110/-1130, TXUL-0010 and TXUL-0011 industrial
SoM modules
- Embest MarS Board i.MX6Dual DIY platform
- Boundary Devices i.MX6 Quad Plus Nitrogen6_MAX and SoloX
Nitrogen6sx embedded boards
- Technexion Pico i.MX6UL compute module
- ZII VF610 Development Board
Marvell embedded (mvebu, orion, kirkwood) platforms:
- Linksys Viper (E4200v2 / EA4500) WiFi router
- Buffalo Kurobox Pro NAS
Qualcomm Snapdragon:
- Arrow DragonBoard 600c (96boards) with APQ8064 Snapdragon 600
Rockchips platform:
- mqmaker MiQi single-board computer
Altera SoCFPGA:
- samtec VIN|ING 1000 vehicle communication interface
Allwinner Sunxi platforms:
- Dserve DSRV9703C tablet
- Difrnce DIT4350 tablet
- Colorfly E708 Q1 tablet
- Polaroid MID2809PXE04 tablet
- Olimex A20 OLinuXino LIME2 single board computer
- Xunlong Orange Pi 2, Orange Pi One, and Orange Pi PC single board
computers
Across many platforms, bug fixes went in to address warnings that dtc
now emits with 'make dtbs W=1'. Further changes for device enablement
went into Ti OMAP, bcm283x (Raspberry Pi), bcm47xx (wifi router), Ti
Davinci, Samsung EXYNOS, Marvell mvebu/kirkwood/orion, NXP i.MX/Vybrid
NXP LPC18xx, NXP LPC32xx, Renesas shmobile/r-mobile/r-car, Rockchips
rk3xxx, ST Ux500, ST STi, Atmel AT91/SAMA5, Altera SoCFPGA, Allwinner
Sunxi, Sigma Designs Tango, NVIDIA Tegra, Socionext Uniphier and ARM
Versatile Express"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (458 commits)
ARM: dts: tango4: Import watchdog node
ARM: dts: tango4: Update cpus node for cpufreq
ARM: dts: tango4: Update DT to match clk driver
ARM: dts: tango4: Initial thermal support
arm/dst: Add Aspeed ast2500 device tree
arm/dts: Add Aspeed ast2400 device tree
ARM: sun7i: dt: Add pll3 and pll7 clocks
ARM: dts: sunxi: Add a olinuxino-lime2-emmc
ARM: dts: at91: sama5d4: add trng node
ARM: dts: at91: sama5d3: add trng node
ARM: dts: at91: sama5d2: add trng node
ARM: dts: at91: at91sam9g45 family: reduce the trng register map size
ARM: sun4i: dt: Add pll3 and pll7 clocks
ARM: sun5i: chip: Enable the TV Encoder
ARM: sun5i: r8: Add display blocks to the DTSI
ARM: sun5i: a13: Add display and TCON clocks
ARM: dts: ux500: configure the accelerometers open drain
ARM: mx5: dts: Enable USB OTG on M53EVK
ARM: dts: imx6ul-14x14-evk: Add audio support
ARM: dts: imx6qdl: Remove unneeded unit-addresses
...
Traditionally we've had two separate branches for cleanups and non-critical
bug fixes, but both of these got smaller with each release and the differences
are rather unclear now, so it seems more appropriate to have a combined
branch.
The most notably change is for OMAP, which gets a small rework to simplify
handling of the AUXDATA mechanism used on machines that are not completely
DT based yet, along with other work that is used as preparation for dropping
the legacy board files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAVzuXUWCrR//JCVInAQKLTw/7BjSDJGRMsioOJ33Bg3LP92rJHPrVttWc
vG8ULnc2QgcFTofDqgyPza2p2XuV868I7jEw4d/qDXOkeIw3ddLKjdCMzHq5r1CO
G9W+ZlIw54na/Lh/CMVdMN1M3+64K4Fmp1IiBG66OhhFY8Zg3xterSEBk8V1+00K
LNdiq6aJ1yROyHQtYbe+CtqTi/pJ9AmkBoRk4MnfgIMQyywESLlYDRkc3VXWEFXv
3MBszgujEIE1R+XozC2VMDPrirdwjJv71x/tlE0nveOcAIam57B/6e5yLnVCQHpu
UCK8x39cj/PwWlwoBExKXNMwbTKCy03AhXjkxDmJ3bD+7FK1sEtFzcyBiwOjiZQq
CBttcwqGbtrGIsLbrbpEh9hAWbWNaparbChWW7RBC1sBIG11zd0HVYjzsKppmXsZ
3LUl4KbkGw+grKa+AnsM+e9vGu+J+2vIh9sDVvs0dbXCZp5ILgExbnurxMwbg/J1
QVycR8cjS2vs+79tTfakgVCSADvpdNbMcnYLz9GM5IS9j8bOlOhv1OhKtMFOue6y
zCIZyffDJqhU0M3xk78JQSx3Rt4FacDjYJdlqN27AQ125QT2kYmfGR2x/en52ARS
9QwauVp+5WcaoySdWi4TCpOMHV7FP40zhJ3G7TXZARaBccN0kCTfdF/QstLhAa0L
u+TVN4A1cBw=
=au7y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanups-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups and fixes from Arnd Bergmann:
"Traditionally we've had two separate branches for cleanups and
non-critical bug fixes, but both of these got smaller with each
release and the differences are rather unclear now, so it seems more
appropriate to have a combined branch.
The most notable change is for OMAP, which gets a small rework to
simplify handling of the AUXDATA mechanism used on machines that are
not completely DT based yet, along with other work that is used as
preparation for dropping the legacy board files"
* tag 'armsoc-cleanups-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: exynos: Add interrupt line to MAX8997 PMIC on exynos4210-trats
ARM: dts: exynos: Fix regulator name to avoid forbidden character on exynos4210-trats
ARM: dts: exynos: Add MFC memory banks for Peach boards
ARM: OMAP2+: n900 needs MMC slot names for legacy user space
ARM: OMAP2+: Add more functions to pwm pdata for ir-rx51
ARM: debug: remove extraneous DEBUG_HI3716_UART option
ARM: OMAP2+: Simplify auxdata by using the generic match
of/platform: Allow secondary compatible match in of_dev_lookup
ARM: davinci: use IRQCHIP_DECLARE for cp_intc
ARM: davinci: remove unused DA8XX_NUM_UARTS
ARM: davinci: simplify call to of populate
ARM: DaVinci USB: removed deprecated properties from MUSB config
ARM: rockchip: Fix use of plain integer as NULL pointer
ARM: realview: hide unused 'pmu_device' object
soc: versatile: dynamically detect RealView HBI numbers
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
Pull networking updates from David Miller:
"Highlights:
1) Support SPI based w5100 devices, from Akinobu Mita.
2) Partial Segmentation Offload, from Alexander Duyck.
3) Add GMAC4 support to stmmac driver, from Alexandre TORGUE.
4) Allow cls_flower stats offload, from Amir Vadai.
5) Implement bpf blinding, from Daniel Borkmann.
6) Optimize _ASYNC_ bit twiddling on sockets, unless the socket is
actually using FASYNC these atomics are superfluous. From Eric
Dumazet.
7) Run TCP more preemptibly, also from Eric Dumazet.
8) Support LED blinking, EEPROM dumps, and rxvlan offloading in mlx5e
driver, from Gal Pressman.
9) Allow creating ppp devices via rtnetlink, from Guillaume Nault.
10) Improve BPF usage documentation, from Jesper Dangaard Brouer.
11) Support tunneling offloads in qed, from Manish Chopra.
12) aRFS offloading in mlx5e, from Maor Gottlieb.
13) Add RFS and RPS support to SCTP protocol, from Marcelo Ricardo
Leitner.
14) Add MSG_EOR support to TCP, this allows controlling packet
coalescing on application record boundaries for more accurate
socket timestamp sampling. From Martin KaFai Lau.
15) Fix alignment of 64-bit netlink attributes across the board, from
Nicolas Dichtel.
16) Per-vlan stats in bridging, from Nikolay Aleksandrov.
17) Several conversions of drivers to ethtool ksettings, from Philippe
Reynes.
18) Checksum neutral ILA in ipv6, from Tom Herbert.
19) Factorize all of the various marvell dsa drivers into one, from
Vivien Didelot
20) Add VF support to qed driver, from Yuval Mintz"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1649 commits)
Revert "phy dp83867: Fix compilation with CONFIG_OF_MDIO=m"
Revert "phy dp83867: Make rgmii parameters optional"
r8169: default to 64-bit DMA on recent PCIe chips
phy dp83867: Make rgmii parameters optional
phy dp83867: Fix compilation with CONFIG_OF_MDIO=m
bpf: arm64: remove callee-save registers use for tmp registers
asix: Fix offset calculation in asix_rx_fixup() causing slow transmissions
switchdev: pass pointer to fib_info instead of copy
net_sched: close another race condition in tcf_mirred_release()
tipc: fix nametable publication field in nl compat
drivers: net: Don't print unpopulated net_device name
qed: add support for dcbx.
ravb: Add missing free_irq() calls to ravb_close()
qed: Remove a stray tab
net: ethernet: fec-mpc52xx: use phy_ethtool_{get|set}_link_ksettings
net: ethernet: fec-mpc52xx: use phydev from struct net_device
bpf, doc: fix typo on bpf_asm descriptions
stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is set
net: ethernet: fs-enet: use phy_ethtool_{get|set}_link_ksettings
net: ethernet: fs-enet: use phydev from struct net_device
...
* pm-cpuidle:
cpuidle: Replace ktime_get() with local_clock()
drivers: firmware: psci: use const and __initconst for psci_cpuidle_ops
soc: qcom: spm: Use const and __initconst for qcom_cpuidle_ops
ARM: cpuidle: constify return value of arm_cpuidle_get_ops()
ARM: cpuidle: add const qualifier to cpuidle_ops member in structures
intel_idle: add BXT support
cpuidle: Indicate when a device has been unregistered
* Change SMD callback parameters
* Use writecombine mapping for SMEM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Jzqj
-----END PGP SIGNATURE-----
Merge tag 'qcom-soc-for-4.7-2' into net-next
This merges the Qualcomm SOC tree with the net-next, solving the
merge conflict in the SMD API between the two.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
- add support for pmic wrapper mt6323
- add support for SoC mt2701
- enable gpt6 arch timer on mt7623
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=35R/
-----END PGP SIGNATURE-----
Merge tag 'v4.6-next-soc' of https://github.com/mbgg/linux-mediatek into next/drivers
Merge "ARM: mediatek soc updates for v4.7" from Matthias Brugger:
- re-organize pmic wrapper code for easier and cleaner addiont of new SoCs and pmic wrappers
- add support for pmic wrapper mt6323
- add support for SoC mt2701
- enable gpt6 arch timer on mt7623
* tag 'v4.6-next-soc' of https://github.com/mbgg/linux-mediatek:
ARM: mediatek: enable gpt6 on boot up to make arch timer work on mt7623
soc: mediatek: PMIC wrap: add MT2701/7623 support
soc: mediatek: PMIC wrap: add mt6323 slave support
soc: mediatek: PMIC wrap: add a slave specific struct
soc: mediatek: PMIC wrap: remove pwrap_is_mt8135() and pwrap_is_mt8173()
soc: mediatek: PMIC wrap: move wdt_src into the pmic_wrapper_type struct
soc: mediatek: PMIC wrap: SPI_WRITE needs a different bitmask for MT2701/7623
soc: mediatek: PMIC wrap: WRAP_INT_EN needs a different bitmask for MT2701/7623
soc: mediatek: PMIC wrap: split SoC specific init into callback
soc: mediatek: PMIC wrap: add wrapper callbacks for init_reg_clock
soc: mediatek: PMIC wrap: don't duplicate the wrapper data
Implements generic PM domain support on top of the existing Tegra power-
gate API. Drivers are thus allowed to move away from the Tegra-specific
API and towards using generic power domains directly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=oeBF
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.7-genpd' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "soc/tegra: Add generic PM domain support" from Thierry Reding:
Implements generic PM domain support on top of the existing Tegra power-
gate API. Drivers are thus allowed to move away from the Tegra-specific
API and towards using generic power domains directly.
* tag 'tegra-for-4.7-genpd' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Add generic PM domain support
dt-bindings: Add power domain info for NVIDIA PMC
settings that get lost and reset on power-domain power cycles.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXIom/AAoJEPOmecmc0R2BB7cH/RYBFTgvgI5PKJ+JuRyJrDh6
KDVTznZ5g+F99v+0PKtkA9qpToct+4Fo08CeLZPrtLR5vp2icQtbnNgHfV6K+JZu
T1NcNHPhI7yufHIBdlvLQlH/o4uLvSYeYuoJA3LwrkI1OYrxElD46PNZEwbGkLiE
oggmef8WtsUnZIeDIM4YVzmJabw8EbSTX+L1TUxMwlOJpR/tcct0RwFDdrBf5uKn
ionob7GblnJaKg045KhjP9bSpoZrltxwjcPqAZSOF9f2waPBqBPZCiFCNUfMLru6
RzzkCm799/6eFFB7wS87S1/6vnal54BnvfZYXIgnq5yStSHYY2VZX0FDkJhEKro=
=hluQ
-----END PGP SIGNATURE-----
Merge tag 'v4.7-rockchip-drivers-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/drivers
Merge "Rockchip driver updates for v4.7 - part2" from Heiko Stübner:
Ability to save and restore the power-domain quality of service
settings that get lost and reset on power-domain power cycles.
* tag 'v4.7-rockchip-drivers-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
soc: rockchip: power-domain: support qos save and restore
dt-bindings: modify document of Rockchip power domains
Adds generic PM domain support to the PMC driver where the PM domains
are populated from device-tree and the PM domain consumer devices are
bound to their relevant PM domains via device-tree as well.
Update the tegra_powergate_sequence_power_up() API so that internally
it calls the same tegra_powergate_xxx functions that are used by the
Tegra generic PM domain code for consistency.
To ensure that the Tegra power domains (a.k.a. powergates) cannot be
controlled via both the legacy tegra_powergate_xxx functions as well
as the generic PM domain framework, add a bit map for available
powergates that can be controlled via the legacy powergate functions.
Move the majority of the tegra_powergate_remove_clamping() function
to a sub-function, so that this can be used by both the legacy and
generic power domain code.
This is based upon work by Thierry Reding <treding@nvidia.com>
and Vince Hsu <vinceh@nvidia.com>.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Introduce a DT-based driver for the R-Car System Controller, as found on
Renesas R-Car H1, R-Car Gen2, and R-Car Gen3 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Lg0X
-----END PGP SIGNATURE-----
Merge tag 'renesas-rcar-sysc2-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
Merge "Second Round of Renesas ARM Based SoC R-Car SYSC Updates for v4.7" from Simon Horman:
Introduce a DT-based driver for the R-Car System Controller, as found on
Renesas R-Car H1, R-Car Gen2, and R-Car Gen3 SoCs.
* tag 'renesas-rcar-sysc2-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (30 commits)
soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
soc: renesas: rcar-sysc: Add support for R-Car H1 power areas
soc: renesas: rcar-sysc: Enable Clock Domain for I/O devices
soc: renesas: rcar-sysc: Make rcar_sysc_power_is_off() static
soc: renesas: rcar-sysc: Add DT support for SYSC PM domains
soc: renesas: rcar-sysc: Improve rcar_sysc_power() debug info
soc: renesas: Move pm-rcar to drivers/soc/renesas/rcar-sysc
clk: renesas: cpg-mssr: Export cpg_mssr_{at,de}tach_dev()
clk: renesas: mstp: Provide dummy attach/detach_dev callbacks
clk: renesas: Provide Kconfig symbols for CPG/MSSR and CPG/MSTP support
soc: renesas: Add r8a7795 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7794 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7793 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7791 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7790 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7779 SYSC PM Domain Binding Definitions
...
R-Car M2-N is identical to R-Car M2-W w.r.t. power domains, so reuse the
definitions from the latter.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On R-Car H3, some power areas (e.g. A3VP) contain I/O devices, which are
also part of the CPG/MSSR Clock Domain.
On all R-Car SoCs, devices in the "always-on" PM Domain are part of the
Clock Domain served by the CPG/MSSR or CPG/MSTP driver.
Hook up the CPG/MSTP or CPG/MSSR Clock Domain attach/detach callbacks to
enable power management using module clocks. Which callback to hook up
depends on the presence of device nodes compatible with
"renesas,cpg-mstp-clocks". This clears the path for a future migration
from the CPG/MSTP to the CPG/MSSR driver on R-Car H1 and
Gen2.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Do not leak a ioremap()'d cookie around, unmaping it in case of errors
Fixes: cef4bafcea ("soc: brcmstb: add SoC driver to brcmstb")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
