- Convert to new *_PM_OPS macros to avoid need for "#ifdef CONFIG_PM_SLEEP"
or "__maybe_unused" (Bjorn Helgaas)
* pci/ctrl/pm-ops:
PCI: Convert to new *_PM_OPS macros
- Add DT binding and driver support for Versal CPM5 Gen5 Root Port (Bharat
Kumar Gogada)
* pci/ctrl/xilinx-cpm:
MAINTAINERS: Add Xilinx Versal CPM Root Port maintainers
PCI: xilinx-cpm: Add support for Versal CPM5 Root Port
dt-bindings: PCI: xilinx-cpm: Add Versal CPM5 Root Port
- Use devm_kasprintf() instead of simple kasprintf() (Subramanian Mohan)
- Add [8086:7D0B] and [8086:AD0B] devices to VMD driver (Francisco Munoz)
* pci/ctrl/vmd:
PCI: vmd: Add DID 8086:7D0B and 8086:AD0B for Intel MTL SKUs
PCI: vmd: Use devm_kasprintf() instead of simple kasprintf()
- Fix tegra_pcie_config_ep() power management in error path (Miaoqian Lin)
- Convert DT binding to json-schema (Vidya Sagar)
- Add DT bindings and driver support for Tegra234 Root Port and Endpoint
mode (Vidya Sagar)
- Disable MSI for Tegra234 Root Ports so they use INTx for all events (PCIe
doesn't allow mixing INTx and MSI/MSI-X) (Vidya Sagar)
- Search for Vendor-Specific RAS-DEC capability instead of hard-coding
offset (Vidya Sagar)
- Fix unintentional APPL_INTR_STATUS_L0 value overwrite in Root Port
interrupt handling (Vidya Sagar)
- Clear Bandwidth Management interrupt status bit to avoid interrupt storm
(Vidya Sagar)
- Set default Max Payload Size to 256 bytes (Vidya Sagar)
- Fix offset when clearing bit in Data Link Feature capability (Vidya
Sagar)
- Extend Endpoint mode support to devices beyond Controller-5 (Vidya Sagar)
* pci/ctrl/tegra194:
PCI: tegra194: Add Tegra234 PCIe support
PCI: tegra194: Extend Endpoint mode support
PCI: tegra194: Fix link up retry sequence
PCI: tegra194: Clean up the exit path for Endpoint mode
PCI: tegra194: Enable support for 256 Byte payload
PCI: tegra194: Clear bandwidth management status
PCI: tegra194: Fix Root Port interrupt handling
PCI: tegra194: Find RAS DES PCIe capability offset
Revert "PCI: tegra194: Rename tegra_pcie_dw to tegra194_pcie"
PCI: Disable MSI for Tegra234 Root Ports
dt-bindings: PCI: tegra234: Add schema for tegra234 Endpoint mode
dt-bindings: PCI: tegra234: Add schema for tegra234 Root Port mode
dt-bindings: PCI: tegra194: Convert to json-schema
PCI: tegra194: Fix PM error handling in tegra_pcie_config_ep()
# Conflicts:
# drivers/pci/controller/dwc/pcie-designware.h
# drivers/pci/controller/dwc/pcie-tegra194.c
- Add PHY clock source implementation (Dmitry Baryshkov)
- Use new clk_regmap_phy_mux_ops for gcc-sm8450 and gcc-sc7280 PCIe pipe
clocks (Dmitry Baryshkov)
- Set up rev 2.1.0 PARF_PHY before enabling clocks (Christian Marangi)
- Power on PHY before accessing IPQ8074 DBI registers to avoid boot hangs
(Robert Marko)
- Power on PHY before accessing DBI registers on all variants for
consistency (Robert Marko)
- Remove unnecessary pipe_clk handling since this is done in PHY drivers
(Dmitry Baryshkov)
- Drop manual pipe_clk_src handling (Dmitry Baryshkov)
- Move GEN3_RELATED DBI definitions to common dwc header (Baruch Siach)
- Define slot capabilities using generic PCI_EXP_SLTCAP_* macros (Baruch
Siach)
- Add IPQ60xx support (Selvam Sathappan Periakaruppan)
- Fix DT description typo (Baruch Siach)
- Fix DT "compatibles" typo (Johan Hovold)
- Allow ASPM L1 and substates for 2.7.0 (Krishna chaitanya chundru)
* pci/ctrl/qcom:
PCI: qcom: Allow ASPM L1 and substates for 2.7.0
dt-bindings: PCI: qcom: Fix reset conditional
dt-bindings: PCI: qcom: Fix description typo
PCI: qcom: Add IPQ60xx support
PCI: qcom: Define slot capabilities using PCI_EXP_SLTCAP_*
PCI: dwc: Move GEN3_RELATED DBI definitions to common header
PCI: qcom: Drop manual pipe_clk_src handling
PCI: qcom: Remove unnecessary pipe_clk handling
PCI: qcom: Power on PHY before DBI register accesses
PCI: qcom: Power on PHY before IPQ8074 DBI register accesses
PCI: qcom: Set up rev 2.1.0 PARF_PHY before enabling clocks
clk: qcom: gcc-sc7280: use new clk_regmap_phy_mux_ops for PCIe pipe clocks
clk: qcom: gcc-sm8450: use new clk_regmap_phy_mux_ops for PCIe pipe clocks
clk: qcom: regmap: add PHY clock source implementation
- Fix refcount leak in mtk_pcie_init_irq_domains() (Miaoqian Lin)
- Print decoded LTSSM state when the link doesn't come up (Jianjun Wang)
* pci/ctrl/mediatek-gen3:
PCI: mediatek-gen3: Print LTSSM state when PCIe link down
PCI: mediatek-gen3: Fix refcount leak in mtk_pcie_init_irq_domains()
- Add Airoha EN7532 to DT binding (John Crispin)
- Allow building of mediatek driver for ARCH_AIROHA (Felix Fietkau)
* pci/ctrl/mediatek:
PCI: mediatek: Allow building for ARCH_AIROHA
dt-bindings: PCI: mediatek: Add Airoha EN7532 support
- Wrap ARM64-specific MCFG quirks in #ifdef so Loongson can use the file
(Huacai Chen)
- Use generic (not 32-bit only) config accesses for LS2K/LS7A (Huacai Chen)
- Add ACPI and MCFG support for Loongson LS7A (Huacai Chen)
- Avoid config reads to non-existent LS2K/LS7A devices because a hardware
defect causes machine hangs (Huacai Chen)
- Work around LS7A integrated devices that report incorrect Interrupt Pin
values (Jianmin Lv)
* pci/ctrl/loongson:
PCI: loongson: Work around LS7A incorrect Interrupt Pin registers
PCI: loongson: Don't access non-existent devices
PCI: loongson: Add ACPI init support
PCI: loongson: Use generic 8/16/32-bit config ops on LS2K/LS7A
PCI/ACPI: Guard ARM64-specific mcfg_quirks
- Factor out ref clock disables to match enables (Bjorn Helgaas)
- Collect clock enables in imx6_pcie_clk_enable() (Richard Zhu)
- Propagate regulator and clock errors back to .host_init() caller (Richard
Zhu)
- Disable i.MX6QDL clock when disabling ref clocks (Richard Zhu)
- Call host init function directly in resume instead of duplicating the
code (Richard Zhu)
- Turn off regulators when suspending (Richard Zhu)
- Make link being down a non-fatal error so probe doesn't fail (Richard
Zhu)
- Start link in resume only if it was up before suspend to reduce resume
time (Richard Zhu)
- Move PHY init and power-on out of clock- and reset-related functions
(Richard Zhu)
- Rework suspend callback to be more symmetric with resume (Richard Zhu)
- Set PCIE_DBI_RO_WR_EN before writing DBI registers (Richard Zhu)
- Allow speeds faster than Gen2 (Richard Zhu)
* pci/ctrl/imx6:
PCI: imx6: Support more than Gen2 speed link mode
PCI: imx6: Set PCIE_DBI_RO_WR_EN before writing DBI registers
PCI: imx6: Reformat suspend callback to keep symmetric with resume
PCI: imx6: Move the imx6_pcie_ltssm_disable() earlier
PCI: imx6: Disable clocks in reverse order of enable
PCI: imx6: Do not hide PHY driver callbacks and refine the error handling
PCI: imx6: Reduce resume time by only starting link if it was up before suspend
PCI: imx6: Mark the link down as non-fatal error
PCI: imx6: Move regulator enable out of imx6_pcie_deassert_core_reset()
PCI: imx6: Turn off regulator when system is in suspend mode
PCI: imx6: Call host init function directly in resume
PCI: imx6: Disable i.MX6QDL clock when disabling ref clocks
PCI: imx6: Propagate .host_init() errors to caller
PCI: imx6: Collect clock enables in imx6_pcie_clk_enable()
PCI: imx6: Factor out ref clock disable to match enable
PCI: imx6: Move imx6_pcie_clk_disable() earlier
PCI: imx6: Move imx6_pcie_enable_ref_clk() earlier
PCI: imx6: Move PHY management functions together
PCI: imx6: Move imx6_pcie_grp_offset(), imx6_pcie_configure_type() earlier
PCI: imx6: Convert to NOIRQ_SYSTEM_SLEEP_PM_OPS()
- Move samsung phy-exynos-pcie init all to exynos5433_pcie_phy_init()
instead of splitting across phy_init() and phy_power_on() (Marek
Szyprowski)
- Call phy_init() before phy_power_on() for samsung phy-exynos-pcie, as
required by the PHY programming model (Marek Szyprowski)
* pci/ctrl/exynos:
PCI: exynos: Correct generic PHY usage
phy: samsung: phy-exynos-pcie: sanitize init/power_on callbacks
- Remove unused struct dw_edma_chip.irq (Frank Li)
- Move eDMA private data from struct dw_edma to struct dw_edma_chip (Frank
Li)
- Convert "struct dw_edma_region rg_region" to "void __iomem *reg_base"
since only the virtual address (not physical address or size) is used
(Frank Li)
- Rename "*_ch_cnt" to "ll_*_cnt" to reflect actual usage (Frank Li)
- Drop dma_slave_config.direction field usage (Serge Semin)
- Fix eDMA Rd/Wr-channels and DMA-direction semantics (Serge Semin)
- Add chip-specific DW_EDMA_CHIP_LOCAL flag to indicate that local eDMA
doesn't require generating MSIs to remote (Frank Li)
- Enable DMA tests for endpoints that support it (Frank Li)
* pci/ctrl/dwc-edma:
PCI: endpoint: Enable DMA tests for endpoints with DMA capabilities
dmaengine: dw-edma: Add support for chip-specific flags
dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction semantics
dmaengine: dw-edma: Drop dma_slave_config.direction field usage
dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct dw_edma_chip
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused irq field in struct dw_edma_chip
- Stop link on host_init errors and de-initialization (Serge Semin)
- Add support for unrolled iATU register space in dw_pcie_disable_atu()
(Serge Semin)
- Disable outbound windows only for controllers that use iATU (Serge Semin)
- Set INCREASE_REGION_SIZE flag based on limit address, not on the size,
since even a small size may cross a 4GB boundary (Serge Semin)
- Deallocate EPC memory on dw_pcie_ep_init() errors to avoid a leak (Serge
Semin)
- Always enable CDM check if "snps,enable-cdm-check" exists instead of
exiting early if the optional "num-lanes" was absent (Serge Semin)
- Simplify detection of whether we're using unrolled iATU registers (Serge
Semin)
- Make dw_pcie_link_up() more generic by using dw_pcie_readl_dbi() instead
of readl() (Serge Semin)
- Add dw_pcie_start_link() and dw_pcie_stop_link() wrappers to factor out
checks for ops being implemented (Serge Semin)
- Move io_cfg_atu_shared to struct pcie_port and rename to cfg0_io_shared,
since it's not used by dwc common code or dwc endpoint code (Serge Semin)
- Rename struct pcie_port to dw_pcie_rp to indicate that it's
DesignWare-specific (Serge Semin)
- Drop unused struct dw_plat_pcie regmap pointer (Serge Semin)
- Fix some coding style issues (Serge Semin)
- Log link speed and width if it comes up (Serge Semin)
- Save DWC IP core version in native format as read from
PORT_LOGIC.PCIE_VERSION_OFF register (Serge Semin)
- Read DWC IP core version from PORT_LOGIC.PCIE_VERSION_OFF (Serge Semin)
- Add macros to compare Synopsys IP core versions (Serge Semin)
- Drop manual DWC IP core version setup from intel-gw and tegra194 (Serge
Semin)
- Add dw_pcie_ops.host_deinit() callback (Serge Semin)
- Drop enum dw_pcie_as_type in favor of PCIE_ATU_TYPE_MEM/IO (Serge Semin)
- Drop enum dw_pcie_region_type in favor of PCIE_ATU_REGION_DIR_IB/OB
(Serge Semin)
- Simplify in/outbound iATU setup methods and reduce duplicated code (Serge
Semin)
- Detect iATU region size from hardware (Serge Semin)
- Validate iATU outbound mappings against hardware constraints (Serge
Semin)
- Check for errors in iATU setup (Serge Semin)
- Allocate a 32-bit DMA-able page to be MSI target instead of using a
driver data structure that may not be addressable with 32-bit address
(Will McVicker)
- Use the bitmap API to allocate bitmaps instead of open-coding it
(Christophe JAILLET)
- Correct dw_pcie_free_msi() checking for when to remove IRQ handler and
data (Dmitry Baryshkov)
- Split MSI init to new dw_pcie_msi_host_init() function (Dmitry Baryshkov)
- Convert struct pcie_port.msi_irq to an array so we can support more than
32 MSI interrupts (Dmitry Baryshkov)
- Handle MSIs routed to multiple GIC interrupts for Qualcomm platforms with
groups of 32 MSI vectors (Dmitry Baryshkov)
- Add additional MSI interrupts to qcom DT (Dmitry Baryshkov)
* pci/ctrl/dwc:
dt-bindings: PCI: qcom: Support additional MSI vectors
PCI: dwc: Handle MSIs routed to multiple GIC interrupts
PCI: dwc: Convert struct pcie_port.msi_irq to an array
PCI: dwc: Split MSI IRQ parsing/allocation to a separate function
PCI: dwc: Correct msi_irq condition in dw_pcie_free_msi()
PCI: dwc: Use the bitmap API to allocate bitmaps
PCI: dwc: Fix MSI msi_msg DMA mapping
PCI: dwc: Check iATU in/outbound range setup status
PCI: dwc: Validate iATU outbound mappings against hardware constraints
PCI: dwc: Add iATU regions size detection procedure
PCI: dwc: Simplify in/outbound iATU setup methods
PCI: dwc: Drop enum dw_pcie_region_type in favor of PCIE_ATU_REGION_DIR_IB/OB
PCI: dwc: Drop enum dw_pcie_as_type in favor of PCIE_ATU_TYPE_MEM/IO
PCI: dwc: Add dw_pcie_ops.host_deinit() callback
PCI: tegra194: Drop manual DW PCIe controller version setup
PCI: intel-gw: Drop manual DW PCIe controller version setup
PCI: dwc: Add macros to compare Synopsys IP core versions
PCI: dwc: Read DWC IP core version from register
PCI: dwc: Use native DWC IP core version representation
PCI: dwc: Detect iATU settings after getting "addr_space" resource
PCI: dwc: Log link speed and width if it comes up
PCI: dwc-plat: Drop dw_plat_pcie_of_match[] forward declaration
PCI: dwc-plat: Drop unused regmap pointer
PCI: dwc-plat: Simplify dw_plat_pcie_probe() return values
PCI: dwc: Rename struct pcie_port to dw_pcie_rp
PCI: dwc: Move io_cfg_atu_shared to struct pcie_port
PCI: dwc: Add start_link/stop_link inlines
PCI: dwc: Reuse local pointer to the resource data
PCI: dwc: Organize local variable usage
PCI: dwc: Convert dw_pcie_link_up() to use dw_pcie_readl_dbi()
PCI: dwc: Simplify unrolled iATU detection
PCI: dwc: Add newlines to log messages
PCI: dwc: Add braces to multi-line if-else statements
PCI: dwc: Always enable CDM check if "snps,enable-cdm-check" exists
PCI: dwc: Deallocate EPC memory on dw_pcie_ep_init() errors
PCI: dwc: Set INCREASE_REGION_SIZE flag based on limit address
PCI: dwc: Disable outbound windows only for controllers using iATU
PCI: dwc: Add unroll iATU space support to dw_pcie_disable_atu()
PCI: dwc: Stop link on host_init errors and de-initialization
- Remove unnecessary forward declarations (Jim Quinlan)
- Prevent config space access when link is down (Jim Quinlan)
- Split post-link up initialization to brcm_pcie_start_link() (Jim Quinlan)
- Enable child bus device regulators described under Root Ports in DT (Jim
Quinlan)
- Disable/enable regulators in suspend/resume (Jim Quinlan)
- Rename .map_bus() functions to end with 'map_bus' as they do in other
drivers (Jim Quinlan)
* pci/ctrl/brcmstb:
PCI: brcmstb: Rename .map_bus() functions to end with 'map_bus'
PCI: brcmstb: Disable/enable regulators in suspend/resume
PCI: brcmstb: Enable child bus device regulators from DT
PCI: brcmstb: Split post-link up initialization to brcm_pcie_start_link()
PCI: brcmstb: Prevent config space access when link is down
PCI: brcmstb: Remove unnecessary forward declarations
- Add support for AER capability on emulated bridge (Pali Rohár)
- Add support for Slot capability on emulated bridge (Pali Rohár)
* pci/ctrl/aardvark:
PCI: aardvark: Fix reporting Slot capabilities on emulated bridge
PCI: aardvark: Add support for AER registers on emulated bridge
- Replace sparc pci_mmap_page_range() wrapper. This still leaves a
sparc-specific pci_mmap_resource_range(), but it's only one interface
instead of two (Arnd Bergmann)
- Remove sparc-specific pci_mmap_resource_range() by implementing
pci_iobar_pfn(). This removes the ability to map the entire PCI I/O
space using /proc/bus/pci, but we believe that's already been broken
since v2.6.28 (Arnd Bergmann)
* pci/resource:
sparc: Use generic pci_mmap_resource_range()
PCI: Remove pci_mmap_page_range() wrapper
- Recognize disconnected devices so we don't bother trying to set them to
"frozen" or "normal" state (Christoph Hellwig)
- Clear PCI Status register during enumeration in case firmware left errors
logged (Kai-Heng Feng)
- Configure ECRC for every device, including hot-added ones (Stefan Roese)
- Keep AER error reporting enabled for switches (Stefan Roese)
- Enable error reporting for all devices that support AER (Stefan Roese)
- Iterate over error counters instead of error strings to avoid printing
junk in AER sysfs counters (Mohamed Khalfella)
* pci/err:
PCI/AER: Iterate over error counters instead of error strings
PCI/AER: Enable error reporting when AER is native
PCI/portdrv: Don't disable AER reporting in get_port_device_capability()
PCI/AER: Configure ECRC for every device
PCI: Clear PCI_STATUS when setting up device
PCI/ERR: Recognize disconnected devices in report_error_detected()
- Split out ARI "next function" handling from the traditional one (Niklas
Schnelle)
- Move jailhouse "isolated function" (non-zero functions where function 0
doesn't exist) handling to pci_scan_slot() to avoid duplicating
multi-function scanning in pci_scan_child_bus_extend() (Niklas Schnelle)
- Extend "isolated function" probing to s390 (Niklas Schnelle).
- Allow s390 zPCI zbus without a function 0 (Niklas Schnelle)
* pci/enumeration:
s390/pci: allow zPCI zbus without a function zero
PCI: Extend isolated function probing to s390
PCI: Move jailhouse's isolated function handling to pci_scan_slot()
PCI: Split out next_ari_fn() from next_fn()
PCI: Clean up pci_scan_slot()
The PCIE_DBI_RO_WR_EN bit should be set when write some DBI registers. To
make sure that the DBI registers are writable, set the PCIE_DBI_RO_WR_EN
properly when writing the DBI registers.
Link: https://lore.kernel.org/r/1652866528-13220-1-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Create imx6_pcie_stop_link() and imx6_pcie_host_exit() functions.
Encapsulate clocks, regulators disables and PHY uninitialization into
imx6_pcie_host_exit().
To keep suspend/resume symmetric as much as possible, invoke these two
new created functions in suspend callback.
To be symmetric with imx6_pcie_host_exit(), move imx6_pcie_clk_enable()
to imx6_pcie_host_init() from imx6_pcie_deassert_core_reset().
Link: https://lore.kernel.org/r/1657783869-19194-18-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Move the imx6_pcie_ltssm_disable() earlier and place it just behind the
imx6_pcie_ltssm_enable(), since it might not be only used by suspend
callback directly.
To be symmetric with imx6_pcie_ltssm_enable(), add the IMX6Q and IMX8MQ
switch cases in imx6_pcie_ltssm_disable().
Link: https://lore.kernel.org/r/1657783869-19194-17-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
imx6_pcie_clk_enable() enables clocks in the order:
pcie_phy
pcie_bus
pcie
imx6_pcie_enable_ref_clk
Change imx6_pcie_clk_disable() to disable them in the reverse order.
Link: https://lore.kernel.org/r/1657783869-19194-16-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Move the phy_power_on() to host_init from imx6_pcie_clk_enable().
Move the phy_init() to host_init from imx6_pcie_deassert_core_reset().
Refine the error handling in imx6_pcie_host_init() accordingly.
Link: https://lore.kernel.org/r/1657783869-19194-15-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
i.MX PCIe doesn't support hotplug. During resume, only start PCIe link
training when the link was up before system suspend to avoid the long
latency in the link training period.
Link: https://lore.kernel.org/r/1657783869-19194-14-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the PCIe link is down, return zero from imx6_pcie_start_link() so the
driver will probe successfully.
Link: https://lore.kernel.org/r/1657783869-19194-13-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Move regulator enable out of imx6_pcie_deassert_core_reset(), since the
regulator_enable() has nothing to do with imx6_pcie_deassert_core_reset().
Link: https://lore.kernel.org/r/1657783869-19194-12-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The driver should undo any enables it did itself. The regulator disable
shouldn't be basing decisions on regulator_is_enabled().
Move the regulator_disable to the suspend function, turn off regulator when
the system is in suspend mode.
Link: https://lore.kernel.org/r/1657783869-19194-11-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Call imx6_pcie_host_init() instead of duplicating codes in resume. Note
that this also means we do MPLL setup again during resume, which we didn't
do before.
[bhelgaas: add MPLL setup note, pointed out by Lucas]
Link: https://lore.kernel.org/r/1657783869-19194-10-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Since dw_pcie_host_init() checks for errors from ops->host_init(),
check for errors when enabling power regulators and clocks and return them.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/1657783869-19194-8-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Encapsulate the i.MX PCIe clock enable operations into one standalone
function, imx6_pcie_clk_enable(). No functional change intended.
[bhelgaas: split pure code moves into separate patches]
Link: https://lore.kernel.org/r/1657783869-19194-7-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
The PCIe ref clocks are specific to different variants. The enables are
already split out into imx6_pcie_enable_ref_clk(), but the disables were
combined with the more generic bus/phy/pcie clock disables in
imx6_pcie_clk_disable().
Split out the variant-specific disables into imx6_pcie_disable_ref_clk() to
match imx6_pcie_enable_ref_clk().
No functional change intended.
Link: https://lore.kernel.org/r/1657783869-19194-6-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Move imx6_pcie_clk_disable() earlier to be near other clock-related
functions. No functional change intended.
[bhelgaas: reorder patch so pure moves are earlier]
Link: https://lore.kernel.org/r/1657783869-19194-5-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Move imx6_pcie_enable_ref_clk() earlier so it's not in the middle between
imx6_pcie_assert_core_reset() and imx6_pcie_deassert_core_reset(). No
functional change intended.
Link: https://lore.kernel.org/r/1657783869-19194-4-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Collect imx6_pcie_init_phy(), imx7d_pcie_wait_for_phy_pll_lock(), and
imx6_setup_phy_mpll() earlier with other PHY-related code. No functional
change intended.
Link: https://lore.kernel.org/r/1657783869-19194-3-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Move imx6_pcie_grp_offset() and imx6_pcie_configure_type() earlier in the
file since they depend on nothing and are used by several other functions
that will be moved earlier. No functional change intended.
Link: https://lore.kernel.org/r/1657783869-19194-2-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Replace SET_NOIRQ_SYSTEM_SLEEP_PM_OPS() with NOIRQ_SYSTEM_SLEEP_PM_OPS(),
which has the advantage that the compiler always sees the PM callbacks as
referenced, so they don't need to be wrapped with "#ifdef CONFIG_PM_SLEEP"
or tagged with "__maybe_unused" to avoid "defined but not used" warnings.
See 1a3c7bb088 ("PM: core: Add new *_PM_OPS macros, deprecate old ones").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
The proper initialization for generic PHYs is to call first phy_init(),
then phy_power_on().
While touching this, remove the phy_reset() call. It is just a left-over
from the obsoleted Exynos5440 support and the current exynos-pcie PHY
driver doesn't even support this function. It is also rarely used by other
drivers.
Link: https://lore.kernel.org/r/20220628220409.26545-2-m.szyprowski@samsung.com
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The exynos-pcie driver called phy_power_on() before phy_init() for some
historical reasons. However the generic PHY framework assumes that the
proper sequence is to call phy_init() first, then phy_power_on(). The
operations done by both functions should be considered as one action and as
such they are called by the exynos-pcie driver (without doing anything
between them). The initialization is just a sequence of register writes,
which cannot be altered without breaking the hardware operation.
To match the generic PHY framework requirement, simply move all register
writes to the phy_init()/phy_exit() and drop power_on()/power_off()
callbacks. This way the driver will also work with the old (incorrect)
PHY initialization call sequence.
Link: https://lore.kernel.org/r/20220628220409.26545-1-m.szyprowski@samsung.com
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
On Qualcomm platforms each group of 32 MSI vectors is routed to the
separate GIC interrupt. Document mapping of additional interrupts.
Link: https://lore.kernel.org/r/20220707134733.2436629-6-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
On some Qualcomm platforms each group of 32 MSI vectors is routed to a
separate GIC interrupt. Implement support for such configurations by
parsing "msi0" ... "msiX" interrupts and attaching them to the chained
handler.
Note that if DT doesn't list an array of MSI interrupts and uses a single
"msi" IRQ, the driver will limit the number of supported MSI vectors to 32.
Link: https://lore.kernel.org/r/20220707134733.2436629-5-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
