was introduced by a patch that tried to fix one bug, but by doing so created
another bug. As both bugs corrupt the output (but they do not crash the
kernel), I decided to fix the design such that it could have both bugs
fixed. The original fix, fixed time reporting of the function graph tracer
when doing a max_depth of one. This was code that can test how much the
kernel interferes with userspace. But in doing so, it could corrupt the time
keeping of the function profiler.
The issue is that the curr_ret_stack variable was being used for two
different meanings. One was to keep track of the stack pointer on the
ret_stack (shadow stack used by the function graph tracer), and the other
use case was the graph call depth. Although, the two may be closely
related, where they got updated was the issue that lead to the two different
bugs that required the two use cases to be updated differently.
The big issue with this fix is that it requires changing each architecture.
The good news is, I was able to remove a lot of code that was duplicated
within the architectures and place it into a single location. Then I could
make the fix in one place.
I pushed this code into linux-next to let it settle over a week, and before
doing so, I cross compiled all the affected architectures to make sure that
they built fine.
In the mean time, I also pulled in a patch that fixes the sched_switch
previous tasks state output, that was not actually correct.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCW/4NPhQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qnWAAQCyUIRLgYImr81eTl52lxNRsULk+aiI
U29kRFWWU0c40AEA1X9sDF0MgOItbRGfZtnHTZEousXRDaDf4Fge2kF7Egg=
=liQ0
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"While rewriting the function graph tracer, I discovered a design flaw
that was introduced by a patch that tried to fix one bug, but by doing
so created another bug.
As both bugs corrupt the output (but they do not crash the kernel), I
decided to fix the design such that it could have both bugs fixed. The
original fix, fixed time reporting of the function graph tracer when
doing a max_depth of one. This was code that can test how much the
kernel interferes with userspace. But in doing so, it could corrupt
the time keeping of the function profiler.
The issue is that the curr_ret_stack variable was being used for two
different meanings. One was to keep track of the stack pointer on the
ret_stack (shadow stack used by the function graph tracer), and the
other use case was the graph call depth. Although, the two may be
closely related, where they got updated was the issue that lead to the
two different bugs that required the two use cases to be updated
differently.
The big issue with this fix is that it requires changing each
architecture. The good news is, I was able to remove a lot of code
that was duplicated within the architectures and place it into a
single location. Then I could make the fix in one place.
I pushed this code into linux-next to let it settle over a week, and
before doing so, I cross compiled all the affected architectures to
make sure that they built fine.
In the mean time, I also pulled in a patch that fixes the sched_switch
previous tasks state output, that was not actually correct"
* tag 'trace-v4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
sched, trace: Fix prev_state output in sched_switch tracepoint
function_graph: Have profiler use curr_ret_stack and not depth
function_graph: Reverse the order of pushing the ret_stack and the callback
function_graph: Move return callback before update of curr_ret_stack
function_graph: Use new curr_ret_depth to manage depth instead of curr_ret_stack
function_graph: Make ftrace_push_return_trace() static
sparc/function_graph: Simplify with function_graph_enter()
sh/function_graph: Simplify with function_graph_enter()
s390/function_graph: Simplify with function_graph_enter()
riscv/function_graph: Simplify with function_graph_enter()
powerpc/function_graph: Simplify with function_graph_enter()
parisc: function_graph: Simplify with function_graph_enter()
nds32: function_graph: Simplify with function_graph_enter()
MIPS: function_graph: Simplify with function_graph_enter()
microblaze: function_graph: Simplify with function_graph_enter()
arm64: function_graph: Simplify with function_graph_enter()
ARM: function_graph: Simplify with function_graph_enter()
x86/function_graph: Simplify with function_graph_enter()
function_graph: Create function_graph_enter() to consolidate architecture code
commit 3f5fe9fef5 ("sched/debug: Fix task state recording/printout")
tried to fix the problem introduced by a previous commit efb40f588b
("sched/tracing: Fix trace_sched_switch task-state printing"). However
the prev_state output in sched_switch is still broken.
task_state_index() uses fls() which considers the LSB as 1. Left
shifting 1 by this value gives an incorrect mapping to the task state.
Fix this by decrementing the value returned by __get_task_state()
before shifting.
Link: http://lkml.kernel.org/r/1540882473-1103-1-git-send-email-pkondeti@codeaurora.org
Cc: stable@vger.kernel.org
Fixes: 3f5fe9fef5 ("sched/debug: Fix task state recording/printout")
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Pull networking fixes from David Miller:
1) Fix some potentially uninitialized variables and use-after-free in
kvaser_usb can drier, from Jimmy Assarsson.
2) Fix leaks in qed driver, from Denis Bolotin.
3) Socket leak in l2tp, from Xin Long.
4) RSS context allocation fix in bnxt_en from Michael Chan.
5) Fix cxgb4 build errors, from Ganesh Goudar.
6) Route leaks in ipv6 when removing exceptions, from Xin Long.
7) Memory leak in IDR allocation handling of act_pedit, from Davide
Caratti.
8) Use-after-free of bridge vlan stats, from Nikolay Aleksandrov.
9) When MTU is locked, do not force DF bit on ipv4 tunnels. From
Sabrina Dubroca.
10) When NAPI cached skb is reused, we must set it to the proper initial
state which includes skb->pkt_type. From Eric Dumazet.
11) Lockdep and non-linear SKB handling fix in tipc from Jon Maloy.
12) Set RX queue properly in various tuntap receive paths, from Matthew
Cover.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tuntap: fix multiqueue rx
ipv6: Fix PMTU updates for UDP/raw sockets in presence of VRF
tipc: don't assume linear buffer when reading ancillary data
tipc: fix lockdep warning when reinitilaizing sockets
net-gro: reset skb->pkt_type in napi_reuse_skb()
tc-testing: tdc.py: Guard against lack of returncode in executed command
tc-testing: tdc.py: ignore errors when decoding stdout/stderr
ip_tunnel: don't force DF when MTU is locked
MAINTAINERS: Add entry for CAKE qdisc
net: bridge: fix vlan stats use-after-free on destruction
socket: do a generic_file_splice_read when proto_ops has no splice_read
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
Revert "net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs"
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
net/sched: act_pedit: fix memory leak when IDR allocation fails
net: lantiq: Fix returned value in case of error in 'xrx200_probe()'
ipv6: fix a dst leak when removing its exception
net: mvneta: Don't advertise 2.5G modes
drivers/net/ethernet/qlogic/qed/qed_rdma.h: fix typo
net/mlx4: Fix UBSAN warning of signed integer overflow
...
The life-checking function, which is used by kAFS to make sure that a call
is still live in the event of a pending signal, only samples the received
packet serial number counter; it doesn't actually provoke a change in the
counter, rather relying on the server to happen to give us a packet in the
time window.
Fix this by adding a function to force a ping to be transmitted.
kAFS then keeps track of whether there's been a stall, and if so, uses the
new function to ping the server, resetting the timeout to allow the reply
to come back.
If there's a stall, a ping and the call is *still* stalled in the same
place after another period, then the call will be aborted.
Fixes: bc5e3a546d ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals")
Fixes: f4d15fb6f9 ("rxrpc: Provide functions for allowing cleaner handling of signals")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When copying to the latency type, we should be passing LATENCY_TYPE_LEN,
not DOMAIN_LEN (this isn't a problem in practice because we only pass
"total" or "I/O"). Fix it by changing all of the strlcpy() calls to use
sizeof().
Fixes: 6c3b7af1c9 ("kyber: add tracepoints")
Reported-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Tested-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull AFS updates from Al Viro:
"AFS series, with some iov_iter bits included"
* 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (26 commits)
missing bits of "iov_iter: Separate type from direction and use accessor functions"
afs: Probe multiple fileservers simultaneously
afs: Fix callback handling
afs: Eliminate the address pointer from the address list cursor
afs: Allow dumping of server cursor on operation failure
afs: Implement YFS support in the fs client
afs: Expand data structure fields to support YFS
afs: Get the target vnode in afs_rmdir() and get a callback on it
afs: Calc callback expiry in op reply delivery
afs: Fix FS.FetchStatus delivery from updating wrong vnode
afs: Implement the YFS cache manager service
afs: Remove callback details from afs_callback_break struct
afs: Commit the status on a new file/dir/symlink
afs: Increase to 64-bit volume ID and 96-bit vnode ID for YFS
afs: Don't invoke the server to read data beyond EOF
afs: Add a couple of tracepoints to log I/O errors
afs: Handle EIO from delivery function
afs: Fix TTL on VL server and address lists
afs: Implement VL server rotation
afs: Improve FS server rotation error handling
...
Merge updates from Andrew Morton:
- a few misc things
- ocfs2 updates
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (132 commits)
hugetlbfs: dirty pages as they are added to pagecache
mm: export add_swap_extent()
mm: split SWP_FILE into SWP_ACTIVATED and SWP_FS
tools/testing/selftests/vm/map_fixed_noreplace.c: add test for MAP_FIXED_NOREPLACE
mm: thp: relocate flush_cache_range() in migrate_misplaced_transhuge_page()
mm: thp: fix mmu_notifier in migrate_misplaced_transhuge_page()
mm: thp: fix MADV_DONTNEED vs migrate_misplaced_transhuge_page race condition
mm/kasan/quarantine.c: make quarantine_lock a raw_spinlock_t
mm/gup: cache dev_pagemap while pinning pages
Revert "x86/e820: put !E820_TYPE_RAM regions into memblock.reserved"
mm: return zero_resv_unavail optimization
mm: zero remaining unavailable struct pages
tools/testing/selftests/vm/gup_benchmark.c: add MAP_HUGETLB option
tools/testing/selftests/vm/gup_benchmark.c: add MAP_SHARED option
tools/testing/selftests/vm/gup_benchmark.c: allow user specified file
tools/testing/selftests/vm/gup_benchmark.c: fix 'write' flag usage
mm/gup_benchmark.c: add additional pinning methods
mm/gup_benchmark.c: time put_page()
mm: don't raise MEMCG_OOM event due to failed high-order allocation
mm/page-writeback.c: fix range_cyclic writeback vs writepages deadlock
...
Refaults happen during transitions between workingsets as well as in-place
thrashing. Knowing the difference between the two has a range of
applications, including measuring the impact of memory shortage on the
system performance, as well as the ability to smarter balance pressure
between the filesystem cache and the swap-backed workingset.
During workingset transitions, inactive cache refaults and pushes out
established active cache. When that active cache isn't stale, however,
and also ends up refaulting, that's bonafide thrashing.
Introduce a new page flag that tells on eviction whether the page has been
active or not in its lifetime. This bit is then stored in the shadow
entry, to classify refaults as transitioning or thrashing.
How many page->flags does this leave us with on 32-bit?
20 bits are always page flags
21 if you have an MMU
23 with the zone bits for DMA, Normal, HighMem, Movable
29 with the sparsemem section bits
30 if PAE is enabled
31 with this patch.
So on 32-bit PAE, that leaves 1 bit for distinguishing two NUMA nodes. If
that's not enough, the system can switch to discontigmem and re-gain the 6
or 7 sparsemem section bits.
Link: http://lkml.kernel.org/r/20180828172258.3185-3-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Daniel Drake <drake@endlessm.com>
Tested-by: Suren Baghdasaryan <surenb@google.com>
Cc: Christopher Lameter <cl@linux.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Johannes Weiner <jweiner@fb.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Enderborg <peter.enderborg@sony.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Vinayak Menon <vinmenon@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Highlights include:
Stable fixes:
- Fix the NFSv4.1 r/wsize sanity checking
- Reset the RPC/RDMA credit grant properly after a disconnect
- Fix a missed page unlock after pg_doio()
Features and optimisations:
- Overhaul of the RPC client socket code to eliminate a locking bottleneck
and reduce the latency when transmitting lots of requests in parallel.
- Allow parallelisation of the RPCSEC_GSS encoding of an RPC request.
- Convert the RPC client socket receive code to use iovec_iter() for
improved efficiency.
- Convert several NFS and RPC lookup operations to use RCU instead of
taking global locks.
- Avoid the need for BH-safe locks in the RPC/RDMA back channel.
Bugfixes and cleanups:
- Fix lock recovery during NFSv4 delegation recalls
- Fix the NFSv4 + NFSv4.1 "lookup revalidate + open file" case.
- Fixes for the RPC connection metrics
- Various RPC client layer cleanups to consolidate stream based sockets
- RPC/RDMA connection cleanups
- Simplify the RPC/RDMA cleanup after memory operation failures
- Clean ups for NFS v4.2 copy completion and NFSv4 open state reclaim.
-----BEGIN PGP SIGNATURE-----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=Fn8z
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.20-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Stable fixes:
- Fix the NFSv4.1 r/wsize sanity checking
- Reset the RPC/RDMA credit grant properly after a disconnect
- Fix a missed page unlock after pg_doio()
Features and optimisations:
- Overhaul of the RPC client socket code to eliminate a locking
bottleneck and reduce the latency when transmitting lots of
requests in parallel.
- Allow parallelisation of the RPCSEC_GSS encoding of an RPC request.
- Convert the RPC client socket receive code to use iovec_iter() for
improved efficiency.
- Convert several NFS and RPC lookup operations to use RCU instead of
taking global locks.
- Avoid the need for BH-safe locks in the RPC/RDMA back channel.
Bugfixes and cleanups:
- Fix lock recovery during NFSv4 delegation recalls
- Fix the NFSv4 + NFSv4.1 "lookup revalidate + open file" case.
- Fixes for the RPC connection metrics
- Various RPC client layer cleanups to consolidate stream based
sockets
- RPC/RDMA connection cleanups
- Simplify the RPC/RDMA cleanup after memory operation failures
- Clean ups for NFS v4.2 copy completion and NFSv4 open state
reclaim"
* tag 'nfs-for-4.20-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (97 commits)
SUNRPC: Convert the auth cred cache to use refcount_t
SUNRPC: Convert auth creds to use refcount_t
SUNRPC: Simplify lookup code
SUNRPC: Clean up the AUTH cache code
NFS: change sign of nfs_fh length
sunrpc: safely reallow resvport min/max inversion
nfs: remove redundant call to nfs_context_set_write_error()
nfs: Fix a missed page unlock after pg_doio()
SUNRPC: Fix a compile warning for cmpxchg64()
NFSv4.x: fix lock recovery during delegation recall
SUNRPC: use cmpxchg64() in gss_seq_send64_fetch_and_inc()
xprtrdma: Squelch a sparse warning
xprtrdma: Clean up xprt_rdma_disconnect_inject
xprtrdma: Add documenting comments
xprtrdma: Report when there were zero posted Receives
xprtrdma: Move rb_flags initialization
xprtrdma: Don't disable BH's in backchannel server
xprtrdma: Remove memory address of "ep" from an error message
xprtrdma: Rename rpcrdma_qp_async_error_upcall
xprtrdma: Simplify RPC wake-ups on connect
...
Dispatching a report zones command through the request queue is a major
pain due to the command reply payload rewriting necessary. Given that
blkdev_report_zones() is executing everything synchronously, implement
report zones as a block device file operation instead, allowing major
simplification of the code in many places.
sd, null-blk, dm-linear and dm-flakey being the only block device
drivers supporting exposing zoned block devices, these drivers are
modified to provide the device side implementation of the
report_zones() block device file operation.
For device mappers, a new report_zones() target type operation is
defined so that the upper block layer calls blkdev_report_zones() can
be propagated down to the underlying devices of the dm targets.
Implementation for this new operation is added to the dm-linear and
dm-flakey targets.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
[Damien]
* Changed method block_device argument to gendisk
* Various bug fixes and improvements
* Added support for null_blk, dm-linear and dm-flakey.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
allocation for bigalloc file systems; fix up some syzbot-detected
races in EXT4_IOC_MOVE_EXT, EXT4_IOC_SWAP_BOOT, and ext4_remount; and
a few other miscellaneous bugs and optimizations.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAlvQYEcACgkQ8vlZVpUN
gaOPYAgAh0BF7mTRnHAp/qkR5ZhDi3ecb3TpNlnpfzoDqQhPYETFisc18DD4HwTj
wctwzSdYxYodeuPIK+R2bBzUy3FuSwtlER9cdr1ilcrUYPZHbir1rPPfTNb/oDGx
WNcd/aulLjuU1eKDODowqMOF2HDchiJHqJqMBa+LfCHck1x/bt2uqdjNA5A1p5AV
lp07DoXT54q5rWJDaXpbxTShWKhzHlRKbB9PKEvMHgPNl9sn5oRReRMKAW+WkT91
e3mfy/GhzhugdWxYUg2oAn3dbqYkkAjW96WnBhCQHioW9ASphjl7yBi1LWh2aPA4
haGxe5W3En8q678ZVtTVNJOyvbW81Q==
=VgdS
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
- further restructure ext4 documentation
- fix up ext4's delayed allocation for bigalloc file systems
- fix up some syzbot-detected races in EXT4_IOC_MOVE_EXT,
EXT4_IOC_SWAP_BOOT, and ext4_remount
- ... and a few other miscellaneous bugs and optimizations.
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (21 commits)
ext4: fix use-after-free race in ext4_remount()'s error path
ext4: cache NULL when both default_acl and acl are NULL
docs: promote the ext4 data structures book to top level
docs: move ext4 administrative docs to admin-guide/
jbd2: fix use after free in jbd2_log_do_checkpoint()
ext4: propagate error from dquot_initialize() in EXT4_IOC_FSSETXATTR
ext4: fix setattr project check in fssetxattr ioctl
docs: make ext4 readme tables readable
docs: fix ext4 documentation table formatting problems
docs: generate a separate ext4 pdf file from the documentation
ext4: convert fault handler to use vm_fault_t type
ext4: initialize retries variable in ext4_da_write_inline_data_begin()
ext4: fix EXT4_IOC_SWAP_BOOT
ext4: fix build error when DX_DEBUG is defined
ext4: fix argument checking in EXT4_IOC_MOVE_EXT
ext4: fix reserved cluster accounting at page invalidation time
ext4: adjust reserved cluster count when removing extents
ext4: reduce reserved cluster count by number of allocated clusters
ext4: fix reserved cluster accounting at delayed write time
ext4: add new pending reservation mechanism
...
-----BEGIN PGP SIGNATURE-----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=g5+b
-----END PGP SIGNATURE-----
Merge tag 'for-4.20-part1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs updates from David Sterba:
"This is the first batch with fixes and some nice performance
improvements.
Preliminary results show eg. more files/sec in fsmark, better perf on
multi-threaded workloads (filebench, dbench), fewer context switches
and overall better memory allocation characteristics (multiple
benchmarks).
Apart from general performance, there's an improvement for qgroups +
balance workload that's been troubling our users.
Note for stable: there are 20+ patches tagged for stable, out of 90.
Not all of them apply cleanly on all stable versions but the conflicts
are mostly due to simple cleanups and resolving should be obvious. The
fixes are otherwise independent.
Performance improvements:
- transition between blocking and spinning modes of path is gone,
which originally resulted to more unnecessary wakeups and updates
to the path locks, the effects are measurable and improve latency
and scalability
- qgroups: first batch of changes that should speedup balancing with
qgroups on, skip quota accounting on unchanged subtrees, overall
gain is about 30+% in runtime
- use rb-tree with cached first node for several structures, small
improvement to avoid pointer chasing
Fixes:
- trim
- fix: some blockgroups could have been missed if their logical
address was past the total filesystem size (ie. after a lot of
balancing)
- better error reporting, after processing blockgroups and whole
device
- fix: continue trimming block groups after an error is
encountered
- check for trim support of the device earlier and avoid some
unnecessary work
- less interaction with transaction commit that improves latency
on slower storage (eg. image files over NFS)
- fsync
- fix warning when replaying log after fsync of a O_TMPFILE
- fix wrong dentries after fsync of file that got its parent
replaced
- qgroups: fix rescan that might misc some dirty groups
- don't clean dirty pages during buffered writes, this could lead to
lost updates in some corner cases
- some block groups could have been delayed in creation, if the
allocation triggered another one
- error handling improvements
Cleanups:
- removed unused struct members and variables
- function return type cleanups
- delayed refs code refactoring
- protect against deadlock that could be caused by crafted image that
tries to allocate from a tree that's locked already"
* tag 'for-4.20-part1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: (93 commits)
btrfs: switch return_bigger to bool in find_ref_head
btrfs: remove fs_info from btrfs_should_throttle_delayed_refs
btrfs: remove fs_info from btrfs_check_space_for_delayed_refs
btrfs: delayed-ref: pass delayed_refs directly to btrfs_delayed_ref_lock
btrfs: delayed-ref: pass delayed_refs directly to btrfs_select_ref_head
btrfs: qgroup: move the qgroup->members check out from (!qgroup)'s else branch
btrfs: relocation: Remove redundant tree level check
btrfs: relocation: Cleanup while loop using rbtree_postorder_for_each_entry_safe
btrfs: qgroup: Avoid calling qgroup functions if qgroup is not enabled
Btrfs: fix wrong dentries after fsync of file that got its parent replaced
Btrfs: fix warning when replaying log after fsync of a tmpfile
btrfs: drop min_size from evict_refill_and_join
btrfs: assert on non-empty delayed iputs
btrfs: make sure we create all new block groups
btrfs: reset max_extent_size on clear in a bitmap
btrfs: protect space cache inode alloc with GFP_NOFS
btrfs: release metadata before running delayed refs
Btrfs: kill btrfs_clear_path_blocking
btrfs: dev-replace: remove pointless assert in write unlock
btrfs: dev-replace: move replace members out of fs_info
...
Pull siginfo updates from Eric Biederman:
"I have been slowly sorting out siginfo and this is the culmination of
that work.
The primary result is in several ways the signal infrastructure has
been made less error prone. The code has been updated so that manually
specifying SEND_SIG_FORCED is never necessary. The conversion to the
new siginfo sending functions is now complete, which makes it
difficult to send a signal without filling in the proper siginfo
fields.
At the tail end of the patchset comes the optimization of decreasing
the size of struct siginfo in the kernel from 128 bytes to about 48
bytes on 64bit. The fundamental observation that enables this is by
definition none of the known ways to use struct siginfo uses the extra
bytes.
This comes at the cost of a small user space observable difference.
For the rare case of siginfo being injected into the kernel only what
can be copied into kernel_siginfo is delivered to the destination, the
rest of the bytes are set to 0. For cases where the signal and the
si_code are known this is safe, because we know those bytes are not
used. For cases where the signal and si_code combination is unknown
the bits that won't fit into struct kernel_siginfo are tested to
verify they are zero, and the send fails if they are not.
I made an extensive search through userspace code and I could not find
anything that would break because of the above change. If it turns out
I did break something it will take just the revert of a single change
to restore kernel_siginfo to the same size as userspace siginfo.
Testing did reveal dependencies on preferring the signo passed to
sigqueueinfo over si->signo, so bit the bullet and added the
complexity necessary to handle that case.
Testing also revealed bad things can happen if a negative signal
number is passed into the system calls. Something no sane application
will do but something a malicious program or a fuzzer might do. So I
have fixed the code that performs the bounds checks to ensure negative
signal numbers are handled"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (80 commits)
signal: Guard against negative signal numbers in copy_siginfo_from_user32
signal: Guard against negative signal numbers in copy_siginfo_from_user
signal: In sigqueueinfo prefer sig not si_signo
signal: Use a smaller struct siginfo in the kernel
signal: Distinguish between kernel_siginfo and siginfo
signal: Introduce copy_siginfo_from_user and use it's return value
signal: Remove the need for __ARCH_SI_PREABLE_SIZE and SI_PAD_SIZE
signal: Fail sigqueueinfo if si_signo != sig
signal/sparc: Move EMT_TAGOVF into the generic siginfo.h
signal/unicore32: Use force_sig_fault where appropriate
signal/unicore32: Generate siginfo in ucs32_notify_die
signal/unicore32: Use send_sig_fault where appropriate
signal/arc: Use force_sig_fault where appropriate
signal/arc: Push siginfo generation into unhandled_exception
signal/ia64: Use force_sig_fault where appropriate
signal/ia64: Use the force_sig(SIGSEGV,...) in ia64_rt_sigreturn
signal/ia64: Use the generic force_sigsegv in setup_frame
signal/arm/kvm: Use send_sig_mceerr
signal/arm: Use send_sig_fault where appropriate
signal/arm: Use force_sig_fault where appropriate
...
Pull networking updates from David Miller:
1) Add VF IPSEC offload support in ixgbe, from Shannon Nelson.
2) Add zero-copy AF_XDP support to i40e, from Björn Töpel.
3) All in-tree drivers are converted to {g,s}et_link_ksettings() so we
can get rid of the {g,s}et_settings ethtool callbacks, from Michal
Kubecek.
4) Add software timestamping to veth driver, from Michael Walle.
5) More work to make packet classifiers and actions lockless, from Vlad
Buslov.
6) Support sticky FDB entries in bridge, from Nikolay Aleksandrov.
7) Add ipv6 version of IP_MULTICAST_ALL sockopt, from Andre Naujoks.
8) Support batching of XDP buffers in vhost_net, from Jason Wang.
9) Add flow dissector BPF hook, from Petar Penkov.
10) i40e vf --> generic iavf conversion, from Jesse Brandeburg.
11) Add NLA_REJECT netlink attribute policy type, to signal when users
provide attributes in situations which don't make sense. From
Johannes Berg.
12) Switch TCP and fair-queue scheduler over to earliest departure time
model. From Eric Dumazet.
13) Improve guest receive performance by doing rx busy polling in tx
path of vhost networking driver, from Tonghao Zhang.
14) Add per-cgroup local storage to bpf
15) Add reference tracking to BPF, from Joe Stringer. The verifier can
now make sure that references taken to objects are properly released
by the program.
16) Support in-place encryption in TLS, from Vakul Garg.
17) Add new taprio packet scheduler, from Vinicius Costa Gomes.
18) Lots of selftests additions, too numerous to mention one by one here
but all of which are very much appreciated.
19) Support offloading of eBPF programs containing BPF to BPF calls in
nfp driver, frm Quentin Monnet.
20) Move dpaa2_ptp driver out of staging, from Yangbo Lu.
21) Lots of u32 classifier cleanups and simplifications, from Al Viro.
22) Add new strict versions of netlink message parsers, and enable them
for some situations. From David Ahern.
23) Evict neighbour entries on carrier down, also from David Ahern.
24) Support BPF sk_msg verdict programs with kTLS, from Daniel Borkmann
and John Fastabend.
25) Add support for filtering route dumps, from David Ahern.
26) New igc Intel driver for 2.5G parts, from Sasha Neftin et al.
27) Allow vxlan enslavement to bridges in mlxsw driver, from Ido
Schimmel.
28) Add queue and stack map types to eBPF, from Mauricio Vasquez B.
29) Add back byte-queue-limit support to r8169, with all the bug fixes
in other areas of the driver it works now! From Florian Westphal and
Heiner Kallweit.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2147 commits)
tcp: add tcp_reset_xmit_timer() helper
qed: Fix static checker warning
Revert "be2net: remove desc field from be_eq_obj"
Revert "net: simplify sock_poll_wait"
net: socionext: Reset tx queue in ndo_stop
net: socionext: Add dummy PHY register read in phy_write()
net: socionext: Stop PHY before resetting netsec
net: stmmac: Set OWN bit for jumbo frames
arm64: dts: stratix10: Support Ethernet Jumbo frame
tls: Add maintainers
net: ethernet: ti: cpsw: unsync mcast entries while switch promisc mode
octeontx2-af: Support for NIXLF's UCAST/PROMISC/ALLMULTI modes
octeontx2-af: Support for setting MAC address
octeontx2-af: Support for changing RSS algorithm
octeontx2-af: NIX Rx flowkey configuration for RSS
octeontx2-af: Install ucast and bcast pkt forwarding rules
octeontx2-af: Add LMAC channel info to NIXLF_ALLOC response
octeontx2-af: NPC MCAM and LDATA extract minimal configuration
octeontx2-af: Enable packet length and csum validation
octeontx2-af: Support for VTAG strip and capture
...
Send probes to all the unprobed fileservers in a fileserver list on all
addresses simultaneously in an attempt to find out the fastest route whilst
not getting stuck for 20s on any server or address that we don't get a
reply from.
This alleviates the problem whereby attempting to access a new server can
take a long time because the rotation algorithm ends up rotating through
all servers and addresses until it finds one that responds.
Signed-off-by: David Howells <dhowells@redhat.com>
Implement support for talking to YFS-variant fileservers in the cache
manager and the filesystem client. These implement upgraded services on
the same port as their AFS services.
YFS fileservers provide expanded capabilities over AFS.
Signed-off-by: David Howells <dhowells@redhat.com>
Increase the sizes of the volume ID to 64 bits and the vnode ID (inode
number equivalent) to 96 bits to allow the support of YFS.
This requires the iget comparator to check the vnode->fid rather than i_ino
and i_generation as i_ino is not sufficiently capacious. It also requires
this data to be placed into the vnode cache key for fscache.
For the moment, just discard the top 32 bits of the vnode ID when returning
it though stat.
Signed-off-by: David Howells <dhowells@redhat.com>
afs_extract_data sets up a temporary iov_iter and passes it to AF_RXRPC
each time it is called to describe the remaining buffer to be filled.
Instead:
(1) Put an iterator in the afs_call struct.
(2) Set the iterator for each marshalling stage to load data into the
appropriate places. A number of convenience functions are provided to
this end (eg. afs_extract_to_buf()).
This iterator is then passed to afs_extract_data().
(3) Use the new ITER_DISCARD iterator to discard any excess data provided
by FetchData.
Signed-off-by: David Howells <dhowells@redhat.com>
Include the site of detection of AFS protocol errors in trace lines to
better be able to determine what went wrong.
Signed-off-by: David Howells <dhowells@redhat.com>
Pull scheduler updates from Ingo Molnar:
"The main changes are:
- Migrate CPU-intense 'misfit' tasks on asymmetric capacity systems,
to better utilize (much) faster 'big core' CPUs. (Morten Rasmussen,
Valentin Schneider)
- Topology handling improvements, in particular when CPU capacity
changes and related load-balancing fixes/improvements (Morten
Rasmussen)
- ... plus misc other improvements, fixes and updates"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
sched/completions/Documentation: Add recommendation for dynamic and ONSTACK completions
sched/completions/Documentation: Clean up the document some more
sched/completions/Documentation: Fix a couple of punctuation nits
cpu/SMT: State SMT is disabled even with nosmt and without "=force"
sched/core: Fix comment regarding nr_iowait_cpu() and get_iowait_load()
sched/fair: Remove setting task's se->runnable_weight during PELT update
sched/fair: Disable LB_BIAS by default
sched/pelt: Fix warning and clean up IRQ PELT config
sched/topology: Make local variables static
sched/debug: Use symbolic names for task state constants
sched/numa: Remove unused numa_stats::nr_running field
sched/numa: Remove unused code from update_numa_stats()
sched/debug: Explicitly cast sched_feat() to bool
sched/core: Disable SD_PREFER_SIBLING on asymmetric CPU capacity domains
sched/fair: Don't move tasks to lower capacity CPUs unless necessary
sched/fair: Set rq->rd->overload when misfit
sched/fair: Wrap rq->rd->overload accesses with READ/WRITE_ONCE()
sched/core: Change root_domain->overload type to int
sched/fair: Change 'prefer_sibling' type to bool
sched/fair: Kick nohz balance if rq->misfit_task_load
...
Pull RCU updates from Ingo Molnar:
"The biggest change in this cycle is the conclusion of the big
'simplify RCU to two primary flavors' consolidation work - i.e.
there's a single RCU flavor for any kernel variant (PREEMPT and
!PREEMPT):
- Consolidate the RCU-bh, RCU-preempt, and RCU-sched flavors into a
single flavor similar to RCU-sched in !PREEMPT kernels and into a
single flavor similar to RCU-preempt (but also waiting on
preempt-disabled sequences of code) in PREEMPT kernels.
This branch also includes a refactoring of
rcu_{nmi,irq}_{enter,exit}() from Byungchul Park.
- Now that there is only one RCU flavor in any given running kernel,
the many "rsp" pointers are no longer required, and this cleanup
series removes them.
- This branch carries out additional cleanups made possible by the
RCU flavor consolidation, including inlining now-trivial
functions, updating comments and definitions, and removing
now-unneeded rcutorture scenarios.
- Now that there is only one flavor of RCU in any running kernel,
there is also only on rcu_data structure per CPU. This means that
the rcu_dynticks structure can be merged into the rcu_data
structure, a task taken on by this branch. This branch also
contains a -rt-related fix from Mike Galbraith.
There were also other updates:
- Documentation updates, including some good-eye catches from Joel
Fernandes.
- SRCU updates, most notably changes enabling call_srcu() to be
invoked very early in the boot sequence.
- Torture-test updates, including some preliminary work towards
making rcutorture better able to find problems that result in
insufficient grace-period forward progress.
- Initial changes to RCU to better promote forward progress of grace
periods, including fixing a bug found by Marius Hillenbrand and
David Woodhouse, with the fix suggested by Peter Zijlstra"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (140 commits)
srcu: Make early-boot call_srcu() reuse workqueue lists
rcutorture: Test early boot call_srcu()
srcu: Make call_srcu() available during very early boot
rcu: Convert rcu_state.ofl_lock to raw_spinlock_t
rcu: Remove obsolete ->dynticks_fqs and ->cond_resched_completed
rcu: Switch ->dynticks to rcu_data structure, remove rcu_dynticks
rcu: Switch dyntick nesting counters to rcu_data structure
rcu: Switch urgent quiescent-state requests to rcu_data structure
rcu: Switch lazy counts to rcu_data structure
rcu: Switch last accelerate/advance to rcu_data structure
rcu: Switch ->tick_nohz_enabled_snap to rcu_data structure
rcu: Merge rcu_dynticks structure into rcu_data structure
rcu: Remove unused rcu_dynticks_snap() from Tiny RCU
rcu: Convert "1UL << x" to "BIT(x)"
rcu: Avoid resched_cpu() when rescheduling the current CPU
rcu: More aggressively enlist scheduler aid for nohz_full CPUs
rcu: Compute jiffies_till_sched_qs from other kernel parameters
rcu: Provide functions for determining if call_rcu() has been invoked
rcu: Eliminate ->rcu_qs_ctr from the rcu_dynticks structure
rcu: Motivate Tiny RCU forward progress
...
- Add support for trace events to hwmon core
- Add support for NCT6797D, NCT6798D, MAX31725/6, LTM4686
- Support all AMD Family 15h Model 6xh and Model 7xh processors
in k10temp driver
- Convert ina3221 driver to _info API
- Fixes, cleanups, and improvements in various drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Urmz
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- Add support for trace events to hwmon core
- Add support for NCT6797D, NCT6798D, MAX31725/6, LTM4686
- Support all AMD Family 15h Model 6xh and Model 7xh processors in
k10temp driver
- Convert ina3221 driver to _info API
- Fixes, cleanups, and improvements in various drivers
* tag 'hwmon-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (46 commits)
hwmon: (pmbus) Fix page count auto-detection.
hwmon: (pmbus) remove redundant 'default n' from Kconfig
hwmon: (core) Add trace events to _attr_show/store functions
hwmon: (ina3221) Use _info API to register hwmon device
hwmon: (npcm-750-pwm-fan) Change initial pwm target to 255
hwmon: (ina3221) Validate shunt resistor value from DT
hwmon: (tmp421) make const array 'names' static
hwmon: (core) Add hwmon_in_enable attribute
hwmon: (ina3221) mark PM functions as __maybe_unused
hwmon: (ina3221) Read channel input source info from DT
dt-bindings: hwmon: Add ina3221 documentation
hwmon: (ina3221) Add suspend and resume functions
hwmon: (ina3221) Fix INA3221_CONFIG_MODE macros
hwmon: (ina3221) Add INA3221_CONFIG to volatile_table
MAINTAINERS: Update PMBUS maintainer entry
hwmon: (pwm-fan) Set fan speed to 0 on suspend
hwmon: (pwm-fan) Silence error on probe deferral
hwmon: (scpi-hwmon) remove redundant continue
hwmon: (nct6775) Add support for NCT6798D
hwmon: (nct6775) Add support for NCT6797D
...
-----BEGIN PGP SIGNATURE-----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=LRTT
-----END PGP SIGNATURE-----
Merge tag 'for-4.20/block-20181021' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"This is the main pull request for block changes for 4.20. This
contains:
- Series enabling runtime PM for blk-mq (Bart).
- Two pull requests from Christoph for NVMe, with items such as;
- Better AEN tracking
- Multipath improvements
- RDMA fixes
- Rework of FC for target removal
- Fixes for issues identified by static checkers
- Fabric cleanups, as prep for TCP transport
- Various cleanups and bug fixes
- Block merging cleanups (Christoph)
- Conversion of drivers to generic DMA mapping API (Christoph)
- Series fixing ref count issues with blkcg (Dennis)
- Series improving BFQ heuristics (Paolo, et al)
- Series improving heuristics for the Kyber IO scheduler (Omar)
- Removal of dangerous bio_rewind_iter() API (Ming)
- Apply single queue IPI redirection logic to blk-mq (Ming)
- Set of fixes and improvements for bcache (Coly et al)
- Series closing a hotplug race with sysfs group attributes (Hannes)
- Set of patches for lightnvm:
- pblk trace support (Hans)
- SPDX license header update (Javier)
- Tons of refactoring patches to cleanly abstract the 1.2 and 2.0
specs behind a common core interface. (Javier, Matias)
- Enable pblk to use a common interface to retrieve chunk metadata
(Matias)
- Bug fixes (Various)
- Set of fixes and updates to the blk IO latency target (Josef)
- blk-mq queue number updates fixes (Jianchao)
- Convert a bunch of drivers from the old legacy IO interface to
blk-mq. This will conclude with the removal of the legacy IO
interface itself in 4.21, with the rest of the drivers (me, Omar)
- Removal of the DAC960 driver. The SCSI tree will introduce two
replacement drivers for this (Hannes)"
* tag 'for-4.20/block-20181021' of git://git.kernel.dk/linux-block: (204 commits)
block: setup bounce bio_sets properly
blkcg: reassociate bios when make_request() is called recursively
blkcg: fix edge case for blk_get_rl() under memory pressure
nvme-fabrics: move controller options matching to fabrics
nvme-rdma: always have a valid trsvcid
mtip32xx: fully switch to the generic DMA API
rsxx: switch to the generic DMA API
umem: switch to the generic DMA API
sx8: switch to the generic DMA API
sx8: remove dead IF_64BIT_DMA_IS_POSSIBLE code
skd: switch to the generic DMA API
ubd: remove use of blk_rq_map_sg
nvme-pci: remove duplicate check
drivers/block: Remove DAC960 driver
nvme-pci: fix hot removal during error handling
nvmet-fcloop: suppress a compiler warning
nvme-core: make implicit seed truncation explicit
nvmet-fc: fix kernel-doc headers
nvme-fc: rework the request initialization code
nvme-fc: introduce struct nvme_fcp_op_w_sgl
...
Stable bugfixes:
- Reset credit grant properly after a disconnect
Other bugfixes and cleanups:
- xprt_release_rqst_cong is called outside of transport_lock
- Create more MRs at a time and toss out old ones during recovery
- Various improvements to the RDMA connection and disconnection code:
- Improve naming of trace events, functions, and variables
- Add documenting comments
- Fix metrics and stats reporting
- Fix a tracepoint sparse warning
-----BEGIN PGP SIGNATURE-----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=SxSD
-----END PGP SIGNATURE-----
Merge tag 'nfs-rdma-for-4.20-1' of git://git.linux-nfs.org/projects/anna/linux-nfs
NFS RDMA client updates for Linux 4.20
Stable bugfixes:
- Reset credit grant properly after a disconnect
Other bugfixes and cleanups:
- xprt_release_rqst_cong is called outside of transport_lock
- Create more MRs at a time and toss out old ones during recovery
- Various improvements to the RDMA connection and disconnection code:
- Improve naming of trace events, functions, and variables
- Add documenting comments
- Fix metrics and stats reporting
- Fix a tracepoint sparse warning
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Number of qgroup dirty extents is directly linked to the performance
overhead, so add a new trace event, trace_qgroup_num_dirty_extents(), to
record how many dirty extents is processed in
btrfs_qgroup_account_extents().
This will be pretty handy to analyze later balance performance
improvement.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are two members in struct btrfs_root which indicate root's
objectid: objectid and root_key.objectid.
They are both set to the same value in __setup_root():
static void __setup_root(struct btrfs_root *root,
struct btrfs_fs_info *fs_info,
u64 objectid)
{
...
root->objectid = objectid;
...
root->root_key.objectid = objecitd;
...
}
and not changed to other value after initialization.
grep in btrfs directory shows both are used in many places:
$ grep -rI "root->root_key.objectid" | wc -l
133
$ grep -rI "root->objectid" | wc -l
55
(4.17, inc. some noise)
It is confusing to have two similar variable names and it seems
that there is no rule about which should be used in a certain case.
Since ->root_key itself is needed for tree reloc tree, let's remove
'objecitd' member and unify code to use ->root_key.objectid in all places.
Signed-off-by: Misono Tomohiro <misono.tomohiro@jp.fujitsu.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
Trace events are useful for people who collect data from the
Ftrace outputs. There're people who analyse the relationship
of cpufreq, thermal and hwmon (power/voltage/current) using
the convenient and timestamped Ftrace outputs, while unlike
cpufreq and thermal subsystems the hwmon does not have trace
events supported yet.
So this patch adds initial trace events for the hwmon core.
To call hwmon_attr_base() for aligned attr index numbers, it
also moves the function upward.
Ftrace outputs:
...: hwmon_attr_show_string: index=2, attr_name=in2_label, val=VDD_5V
...: hwmon_attr_show: index=2, attr_name=in2_input, val=5112
...: hwmon_attr_show: index=2, attr_name=curr2_input, val=440
Note that the _attr_show and _attr_store functions are tied
to the _with_info API. So a hwmon driver requiring the trace
events feature should use _with_info API to register a hwmon
device.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
-----BEGIN PGP SIGNATURE-----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=q6E6
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-fixes-20181008' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fix packet reception code
Here are a set of patches that prepares for and fix problems in rxrpc's
package reception code. There serious problems are:
(A) There's a window between binding the socket and setting the data_ready
hook in which packets can find their way into the UDP socket's receive
queues.
(B) The skb_recv_udp() will return an error (and clear the error state) if
there was an error on the Tx side. rxrpc doesn't handle this.
(C) The rxrpc data_ready handler doesn't fully drain the UDP receive
queue.
(D) The rxrpc data_ready handler assumes it is called in a non-reentrant
state.
The second patch fixes (A) - (C); the third patch renders (B) and (C)
non-issues by using the recap_rcv hook instead of data_ready - and the
final patch fixes (D). That last is the most complex.
The preparatory patches are:
(1) Fix some places that are doing things in the wrong net namespace.
(2) Stop taking the rcu read lock as it's held by the IP input routine in
the call chain.
(3) Only end the Tx phase if *we* rotated the final packet out of the Tx
buffer.
(4) Don't assume that the call state won't change after dropping the
call_state lock.
(5) Only take receive window and MTU suze parameters from an ACK packet if
it's the latest ACK packet.
(6) Record connection-level abort information correctly.
(7) Fix a trace line.
And then there are three main patches - note that these are mixed in with
the preparatory patches somewhat:
(1) Fix the setup window (A), skb_recv_udp() error check (B) and packet
drainage (C).
(2) Switch to using the encap_rcv instead of data_ready to cut out the
effects of the UDP read queues and get the packets delivered directly.
(3) Add more locking into the various packet input paths to defend against
re-entrance (D).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the rxrpc_tx_packet trace line by storing the where parameter.
Fixes: 4764c0da69 ("rxrpc: Trace packet transmission")
Signed-off-by: David Howells <dhowells@redhat.com>
Ingo writes:
"scheduler fixes:
These fixes address a rather involved performance regression between
v4.17->v4.19 in the sched/numa auto-balancing code. Since distros
really need this fix we accelerated it to sched/urgent for a faster
upstream merge.
NUMA scheduling and balancing performance is now largely back to
v4.17 levels, without reintroducing the NUMA placement bugs that
v4.18 and v4.19 fixed.
Many thanks to Srikar Dronamraju, Mel Gorman and Jirka Hladky, for
reporting, testing, re-testing and solving this rather complex set of
bugs."
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/numa: Migrate pages to local nodes quicker early in the lifetime of a task
mm, sched/numa: Remove rate-limiting of automatic NUMA balancing migration
sched/numa: Avoid task migration for small NUMA improvement
mm/migrate: Use spin_trylock() while resetting rate limit
sched/numa: Limit the conditions where scan period is reset
sched/numa: Reset scan rate whenever task moves across nodes
sched/numa: Pass destination CPU as a parameter to migrate_task_rq
sched/numa: Stop multiple tasks from moving to the CPU at the same time
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus recently observed that if we did not worry about the padding
member in struct siginfo it is only about 48 bytes, and 48 bytes is
much nicer than 128 bytes for allocating on the stack and copying
around in the kernel.
The obvious thing of only adding the padding when userspace is
including siginfo.h won't work as there are sigframe definitions in
the kernel that embed struct siginfo.
So split siginfo in two; kernel_siginfo and siginfo. Keeping the
traditional name for the userspace definition. While the version that
is used internally to the kernel and ultimately will not be padded to
128 bytes is called kernel_siginfo.
The definition of struct kernel_siginfo I have put in include/signal_types.h
A set of buildtime checks has been added to verify the two structures have
the same field offsets.
To make it easy to verify the change kernel_siginfo retains the same
size as siginfo. The reduction in size comes in a following change.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Clean up: Use a function name that is consistent with the RDMA core
API and with other consumers. Because this is a function that is
invoked from outside the rpcrdma.ko module, add an appropriate
documenting comment.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: Use a function name that is consistent with the RDMA core
API and with other consumers. Because this is a function that is
invoked from outside the rpcrdma.ko module, add an appropriate
documenting comment.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up the names of trace events related to MRs so that it's
easy to enable these with a glob.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
When a memory operation fails, the MR's driver state might not match
its hardware state. The only reliable recourse is to dereg the MR.
This is done in ->ro_recover_mr, which then attempts to allocate a
fresh MR to replace the released MR.
Since commit e2ac236c0b ("xprtrdma: Allocate MRs on demand"),
xprtrdma dynamically allocates MRs. It can add more MRs whenever
they are needed.
That makes it possible to simply release an MR when a memory
operation fails, instead of "recovering" it. It will automatically
be replaced by the on-demand MR allocator.
This commit is a little larger than I wanted, but it replaces
->ro_recover_mr, rb_recovery_lock, rb_recovery_worker, and the
rb_stale_mrs list with a generic work queue.
Since MRs are no longer orphaned, the mrs_orphaned metric is no
longer used.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Rate limiting of page migrations due to automatic NUMA balancing was
introduced to mitigate the worst-case scenario of migrating at high
frequency due to false sharing or slowly ping-ponging between nodes.
Since then, a lot of effort was spent on correctly identifying these
pages and avoiding unnecessary migrations and the safety net may no longer
be required.
Jirka Hladky reported a regression in 4.17 due to a scheduler patch that
avoids spreading STREAM tasks wide prematurely. However, once the task
was properly placed, it delayed migrating the memory due to rate limiting.
Increasing the limit fixed the problem for him.
Currently, the limit is hard-coded and does not account for the real
capabilities of the hardware. Even if an estimate was attempted, it would
not properly account for the number of memory controllers and it could
not account for the amount of bandwidth used for normal accesses. Rather
than fudging, this patch simply eliminates the rate limiting.
However, Jirka reports that a STREAM configuration using multiple
processes achieved similar performance to 4.16. In local tests, this patch
improved performance of STREAM relative to the baseline but it is somewhat
machine-dependent. Most workloads show little or not performance difference
implying that there is not a heavily reliance on the throttling mechanism
and it is safe to remove.
STREAM on 2-socket machine
4.19.0-rc5 4.19.0-rc5
numab-v1r1 noratelimit-v1r1
MB/sec copy 43298.52 ( 0.00%) 44673.38 ( 3.18%)
MB/sec scale 30115.06 ( 0.00%) 31293.06 ( 3.91%)
MB/sec add 32825.12 ( 0.00%) 34883.62 ( 6.27%)
MB/sec triad 32549.52 ( 0.00%) 34906.60 ( 7.24%
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reviewed-by: Rik van Riel <riel@surriel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jirka Hladky <jhladky@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linux-MM <linux-mm@kvack.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20181001100525.29789-2-mgorman@techsingularity.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Modify ext4_ext_remove_space() and the code it calls to correct the
reserved cluster count for pending reservations (delayed allocated
clusters shared with allocated blocks) when a block range is removed
from the extent tree. Pending reservations may be found for the clusters
at the ends of written or unwritten extents when a block range is removed.
If a physical cluster at the end of an extent is freed, it's necessary
to increment the reserved cluster count to maintain correct accounting
if the corresponding logical cluster is shared with at least one
delayed and unwritten extent as found in the extents status tree.
Add a new function, ext4_rereserve_cluster(), to reapply a reservation
on a delayed allocated cluster sharing blocks with a freed allocated
cluster. To avoid ENOSPC on reservation, a flag is applied to
ext4_free_blocks() to briefly defer updating the freeclusters counter
when an allocated cluster is freed. This prevents another thread
from allocating the freed block before the reservation can be reapplied.
Redefine the partial cluster object as a struct to carry more state
information and to clarify the code using it.
Adjust the conditional code structure in ext4_ext_remove_space to
reduce the indentation level in the main body of the code to improve
readability.
Signed-off-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The code in ext4_da_map_blocks sometimes reserves space for more
delayed allocated clusters than it should, resulting in premature
ENOSPC, exceeded quota, and inaccurate free space reporting.
Fix this by checking for written and unwritten blocks shared in the
same cluster with the newly delayed allocated block. A cluster
reservation should not be made for a cluster for which physical space
has already been allocated.
Signed-off-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Ext4 contains a few functions that are used to search for delayed
extents or blocks in the extents status tree. Rather than duplicate
code to add new functions to search for extents with different status
values, such as written or a combination of delayed and unwritten,
generalize the existing code to search for caller-specified extents
status values. Also, move this code into extents_status.c where it
is better associated with the data structures it operates upon, and
where it can be more readily used to implement new extents status tree
functions that might want a broader scope for i_es_lock.
Three missing static specifiers in RFC version of patch reported and
fixed by Fengguang Wu <fengguang.wu@intel.com>.
Signed-off-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Since we will want to introduce similar TCP state variables for the
transmission of requests, let's rename the existing ones to label
that they are for the receive side.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Fix error distribution by immediately delivering the errors to all the
affected calls rather than deferring them to a worker thread. The problem
with the latter is that retries and things can happen in the meantime when we
want to stop that sooner.
To this end:
(1) Stop the error distributor from removing calls from the error_targets
list so that peer->lock isn't needed to synchronise against other adds
and removals.
(2) Require the peer's error_targets list to be accessed with RCU, thereby
avoiding the need to take peer->lock over distribution.
(3) Don't attempt to affect a call's state if it is already marked complete.
Signed-off-by: David Howells <dhowells@redhat.com>
When debugging Kyber, it's really useful to know what latencies we've
been having, how the domain depths have been adjusted, and if we've
actually been throttling. Add three tracepoints, kyber_latency,
kyber_adjust, and kyber_throttled, to record that.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
