Currently the at24 driver only creates additional i2c dummies for
atmel,24c00 and it's hard-coded. Some other chips (like for example
Microchip's 24AA02T) also take more slave addresses despite being
otherwise compatible with already supported variants.
Add a new property to the device tree binding document that defines
the total number of i2c slave addresses taken by the device. The
addresses are counted starting from the one in the reg property.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add new compatible to the device tree bindings.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Currently the only way to use a variant of a supported model with
a different address width is to define a new compatible string and
the corresponding chip data structure.
Provide a flexible way to specify the size of the address pointer
by defining a new property: address-width.
Signed-off-by: Alan Chiang <alanx.chiang@intel.com>
Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[Bartosz: fixed the commit message]
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Document the compatible value for the Renesas R1EX24128ASAS0A two-wire
serial interface EEPROM, so it can be used in DTS files without causing
checkpatch warnings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Both manufacturer and name variant.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
The datasheet talks about the chip being an spd, but the chip is writable
so atmel,24c02 is more appropriate as fallback.
Signed-off-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Makes them easier to find.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Pull i2c updates from Wolfram Sang:
"I2C has the following changes for you:
- new flag to mark DMA safe buffers in i2c_msg. Also, some
infrastructure around it. And docs.
- huge refactoring of the at24 driver led by the new maintainer
Bartosz
- update I2C bus recovery to send STOP after recovery
- conversion from gpio to gpiod for I2C bus recovery
- adding a fault-injector to the i2c-gpio driver
- lots of small driver improvements, and bigger ones to
i2c-sh_mobile"
* 'i2c/for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (99 commits)
i2c: mv64xxx: Add myself as maintainer for this driver
i2c: mv64xxx: Fix clock resource by adding an optional bus clock
i2c: mv64xxx: Remove useless test before clk_disable_unprepare
i2c: mxs: use true and false for boolean values
i2c: meson: update doc description to fix build warnings
i2c: meson: add configurable divider factors
dt-bindings: i2c: update documentation for the Meson-AXG
i2c: imx-lpi2c: add runtime pm support
i2c: rcar: fix some trivial typos in comments
i2c: davinci: fix the cpufreq transition
i2c: rk3x: add proper kerneldoc header
i2c: rk3x: account for const type of of_device_id.data
i2c: acorn: remove outdated path from file header
i2c: acorn: add MODULE_LICENSE tag
i2c: rcar: implement bus recovery
i2c: send STOP after successful bus recovery
i2c: ensure SDA is released in recovery if SDA is controllable
i2c: add 'set_sda' to bus_recovery_info
i2c: add identifier in declarations for i2c_bus_recovery
i2c: make kerneldoc about bus recovery more precise
...
Add other variants of at24 EEPROMs we support in the driver to the
list of allowed compatible fallbacks.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Make formatting and style consistent for the entire document.
This patch doesn't change the content of the binding.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Current description of the compatible property for at24 is quite vague.
State explicitly that any "<manufacturer>,<model>" pair is accepted as
long as a correct fallback is used for non-atmel chips.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
AT24 EEPROMs have a write-protect pin, which - when pulled high -
inhibits writes to the upper quadrant of memory (although it has been
observed that on some chips it disables writing to the entire memory
range).
On some boards, this pin is connected to a GPIO and pulled high by
default, which forces the user to manually change its state before
writing. On linux this means that we either need to hog the line all
the time, or set the GPIO value before writing from outside of the
at24 driver.
Add a new optional property to the device tree binding document, which
allows to specify the GPIO line to which the write-protect pin is
connected.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Adds an optional property for at24 eeproms. This parameterless
property indicates that the multi-address eeprom does not
automatically roll over reads to the next slave address.
Signed-off-by: Sven Van Asbroeck <svendev@arcx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
This binding documentation is for the at24 driver, so the filename
should reflect it. This avoids confusion because we also have an
"eeprom" driver in Linux but it doesn't support DT even.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Certain EEPROMS have a size that is larger than the number of address
bytes would allow, and store the MSB of the address in bit 3 of the
instruction byte.
This can be described in platform data using EE_INSTR_BIT3_IS_ADDR, or
in DT using the obsolete legacy "at25,addr-mode" property.
But currently there exists no non-deprecated way to describe this in DT.
Hence extend the existing "address-width" DT property to allow
specifying 9 address bits, and enable support for that in the driver.
This has been tested with a Microchip 25LC040A.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the recommended presence of a device-specific compatible value,
and list examples that are already in use or soon will be.
This will allow checkpatch to validate compatible values in DTS.
Update the example to match current best practices (generic node name,
specific compatible value first).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
This adds eeprom "size" as optional property for i2c eeproms.
The "size" property allows explicitly specifying the size of the
EEPROM chip in bytes.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Divagar Mohandass <divagar.mohandass@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
Document in the Device Tree binding document that this manufacturer should
be used as the generic fallback. Also document the deprecated vendors.
Suggested-by: Wolfram Sang <wsa@the-dreams.de>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This adds "microchip,24c128" to the list of compatible strings for i2c
eeproms.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
EEPROMs can have additional properties, so they are not suitable for
trivial-devices.txt. Move most bindings to the designated eeprom.txt.
Add the missing "atmel,24c08" while doing that. Note that the remaining
ones in trivial-devices need to be dealt with separately because of
improper manufacturer names.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Create a top level eeprom binding directory and move several scattered
binding files there.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
