Due to the way the tasklets work in mac80211 there's
no need to ever disable them.
However, we need to clear the pending packets when
taking down the last interface because otherwise
the tx_pending_tasklet might be queued if the
driver mucks with the queues (which it shouldn't).
I've had a situation occasionally with ar9170 in
which ksoftirq was using 100% CPU time because
a disabled tasklet was scheduled, and I think that
was due to ar9170 receiving a packet while the
tasklet was disabled. That's strange and it really
should not do that for other reasons, but there's
no need to waste that much CPU time over it, it
should just warn instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the libipw naming scheme change, it is no longer necessary for
mac80211 to avoid the ieee80211_rx name clash.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This expands on the current fwded_frames stat counter which should be equal to
the total of these two new counters. The new counters are called "fwded_mcast"
and "fwded_unicast".
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 11s task group recently changed the frame mesh multicast/broadcast frame
format to use 3-address. This was done to avoid interactions with widely
deployed lazy-WDS access points.
This patch changes the format of group addressed frames, both mesh-originated
and proxied, to use the data format defined in draft D2.08 and forward. The
address fields used for group addressed frames is:
In 802.11 header
ToDS:0 FromDS:1
addr1: DA (broadcast/multicast address)
addr2: TA
addr3: Mesh SA
In address extension header:
addr4: SA (only present if frame was proxied)
Note that this change breaks backward compatibility with earlier mesh stack
versions.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jan reported that his b43-based laptop hangs during suspend.
The problem turned out to be mac80211 asking the driver to
stop the hardware before removing interfaces, and interface
removal caused b43 to touch the hardware (while down, which
causes the hang).
This patch fixes mac80211 to do reorder these operations to
have them in the correct order -- first remove interfaces
and then stop the hardware. Some more code is necessary to
be able to do so in a race-free manner, in particular it is
necessary to not process frames received during quiescing.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13337.
Reported-by: Jan Scholz <scholz@fias.uni-frankfurt.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a station queries us for a PS-poll response, we wrongly
queue the frame on the virtual interface's queue rather than
the pending queue.
Additionally, fix a race condition where we could potentially
send multiple frames to the sleeping station due to using a
station flag rather than a packet flag. When converting to a
packet flag, we can also convert p54 and remove the filter
clearing we added for it.
(Also remove a now dead function)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Bob Copeland <me@bobcopeland.com>
Tested-by: Bob Copeland <me@bobcopeland.com>
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a new scan flag "SCAN_OFF_CHANNEL" which basically tells us
that we are currently on a different channel for scanning and cannot
RX/TX. "SCAN_SW_SCANNING" tells us that we are currently running a
software scan but we might as well be on the operating channel to RX/TX.
While "SCAN_SW_SCANNING" is set during the whole scan "SCAN_OFF_CHANNEL"
is set when leaving the operating channel and unset when coming back.
Introduce two new scan states "SCAN_LEAVE_OPER_CHANNEL" and
"SCAN_ENTER_OPER_CHANNEL" which basically implement the functionality we
need to leave the operating channel (send a nullfunc to the AP and stop
the queues) and enter it again (send a nullfunc to the AP and start the
queues again).
Enhance the scan state "SCAN_DECISION" to switch back to the operating
channel after each scanned channel. In the future it sould be simple
to enhance the decision state to scan as much channels in a row as the
qos latency allows us.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a bitfield to store the current scan mode instead of two boolean
variables {sw,hw}_scanning. This patch does not introduce functional
changes but allows us to enhance the scan flags later (for example
for background scanning).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are still two places in mac80211 that hardcode
the initial net namespace (init_net). One of them is
mandated by cfg80211 and will be removed by a separate
patch, the other one is used for finding the network
device of a pending packet via its ifindex.
Remove the latter use by keeping track of the device
pointer itself, via the vif pointer, and avoid it
going stale by dropping pending frames for a given
interface when the interface is removed.
To keep track of the vif pointer for the correct
interface, change the info->control.vif pointer's
internal use to always be the correct vif, and only
move it to the vif the driver expects (or NULL for
monitor interfaces and injected packets) right before
giving the packet to the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The removal of the master netdev broke the mesh forwarding path. This patch
fixes it by using the new internal 'pending' queue.
As a result of this change, mesh forwarding no longer does the inefficient
802.11 -> 802.3 -> 802.11 conversion that was done before.
[Changes since v1]
Suggested by Johannes:
- Select queue before adding to mpath queue
- ieee80211_add_pending_skb -> ieee80211_add_pending_skbs
- Remove unnecessary header wme.h
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the internal 'pending' queue system in place, we can simply
put packets there instead of pushing them off to the master dev,
getting rid of the master interface completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the recent MLME rework I accidentally removed the connection
monitoring code. In order to add it back, this patch will add new
code to monitor both for beacon loss and for the connection actually
working, with possibly separate triggers.
When no unicast frames have been received from the AP for (currently)
two seconds, we will send the AP a probe request. Also, when we don't
see beacons from the AP for two seconds, we do the same (but those
times need not be the same due to the way the code is now written).
Additionally, clean up the parameters to the ieee80211_set_disassoc()
function that I need here, those are all useless except sdata.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sit tight. This shakes up the world as you know
it. Let go of your spaghetti tongs, they will no
longer be required, the horrible statemachine in
net/mac80211/mlme.c is no more...
With the cfg80211 SME mac80211 now has much less
to keep track of, but, on the other hand, for FT
it needs to be able to keep track of at least one
authentication being in progress while associated.
So convert from a single state machine to having
small ones for all the different things we need to
do. For real FT it will still need work wrt. PS,
but this should be a good step.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding GFP_ATOMIC everywhere, add a
new function parameter that gets the flags from the
caller. Obviously then I need to update all callers
(all of them in mac80211), and it turns out that now
it's ok to use GFP_KERNEL in almost all places.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Within mac80211, we often need to copy the rx status into
skb->cb. This is wasteful, as drivers could be building it
in there to start with. This patch changes the API so that
drivers are expected to pass the RX status in skb->cb, now
accessible as IEEE80211_SKB_RXCB(skb). It also updates all
drivers to pass the rx status in there, but only by making
them memcpy() it into place before the call to the receive
function (ieee80211_rx(_irqsafe)). Each driver can now be
optimised on its own schedule.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to handle powersave frames properly we had needed
to pass these out to the device queues again, and introduce
the skb->requeue bit. This, however, also has unnecessary
overhead by needing to 'clean up' already tried frames, and
this clean-up code is also buggy when software encryption
is used.
Instead of sending the frames via the master netdev queue
again, simply put them into the pending queue. This also
fixes a problem where frames for that particular station
could be reordered when some were still on the software
queues and older ones are re-injected into the software
queue after them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 is checking is the skb is aligned on 32 bit boundary.
But it is checking against ethernet header, whereas Linux expect IP
header aligned. And ethernet ether size is 6*2+2=14, so aligning
ethernet header make IP header unaligned.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch moves some utility functions from mac80211 to cfg80211.
Because these functions are doing generic 802.11 operations so they
are not mac80211 specific. The moving allows some fullmac drivers
to be also benefit from these utility functions.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel switch code is currently in the spectrum
management file, where arguably it belongs. However,
it is for managed mode only and uses the structures
for that mode only so having it in a more generic
file can be confusing. Additionally, my next patch
gets simpler with the code here.
When/if we ever implement this for IBSS or mesh then
we will need to rework the structures it uses anyway
at which point we could move the code back.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When management frame protection (IEEE 802.11w) is used, unprotected
Robust Action frames are not allowed prior to key configuration.
However, unprotected Deauthentication and Disassociation frames are
allowed at that point, but not after key configuration.
Make ieee80211_drop_unencrypted() handle the special cases for MFP by
separating the basic Data frame case from Management frame processing
and handle the Management frames only if MFP has been negotiated. In
addition, do not use sdata->drop_unencrypted for Management frames
since the decision on whether to accept the frame depends on the key
being configured.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using nl80211, we do not have a mechanism to set
sdata->drop_unencrypted. Currently, this breaks code that is supposed
to drop unencrypted frames when protection is expected since
ieee80211_rx_h_decrypt() is optimized to not set rx->key when the
frame is not protected.
This patch modifies ieee80211_rx_h_decrypt() to set rx->key for all
frames and only skip decryption if the frame is not protected. This
allows ieee80211_drop_unencrypted() to correctly drop frames even if
drop_unencrypted is not set.
The changes here are not enough to handle all cases, though. Additional
patches will be needed to implement proper IEEE 802.1X PAE for station
mode (currently, this is only used for AP mode) and some additional
rules are needed for MFP to drop unprotected Robust Action frames prior
to having PTK and IGTK configured.
In theory, the unprotected frames could and should be dropped in
ieee80211_rx_h_decrypt(). However, due to the special case with EAPOL
frames that have to be allowed to be received unprotected even when
keys are set, it is simpler to only set rx->key and allow the
ieee80211_frame_allowed() function to handle the actual dropping of
data frames after 802.11->802.3 header conversion. In addition,
unprotected robust management frames are dropped before they are
processed.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are currently processing block ack reordering as a separate task
before all other RX handlers. In theory, this is wrong since this step
should be done only after duplicate removal (see Figure 6-1 in IEEE
802.11n). However, moving this needs some work and the current
situation is not too bad. Add a comment here so that this small detail
does not get forgotten and who knows, maybe someone has some extra
time to take a look at cleaning this up.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows skbs to be released from the RX reorder buffer in
case they have been there for an unexpectedly long time without us
having received the missing frames before them. Previously, these
frames were only released when the reorder window moved and that could
take very long time unless new frames were received constantly (e.g.,
TCP connections could be killed more or less indefinitely).
This situation should not happen very frequently, but it looks like
there are some scenarious that trigger it for some reason. As such,
this should be considered mostly a workaround to speed up recovery
from unexpected siutation that could result in connections hanging for
long periods of time.
The changes here will only check for timeout situation when adding new
RX frames to the reorder buffer. It does not handle all possible
cases, but seems to help for most cases that could result from common
network usage (e.g., TCP retrying at least couple of times). For more
completely coverage, a timer could be used to periodically check
whether there are any frames remaining in the reorder buffer if no new
frames are received.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to duplicate the same code in two places (and that would be
three after the followup patch).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to later add tracing or verifications to the driver
calls mac80211 makes, this patch adds static inline wrappers
for all operations.
All calls are now written as
drv_<op>(local, ...);
instead of
local->ops-><op>(&local->hw, ...);
Where necessary, the wrappers also do existence checking and
return default values as appropriate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Define a new nl80211 event, NL80211_CMD_MICHAEL_MIC_FAILURE, to be
used to notify user space about locally detected Michael MIC failures.
This matches with the MLME-MICHAELMICFAILURE.indication() primitive.
Since we do not actually have TSC in the skb anymore when
mac80211_ev_michael_mic_failure() is called, that function is changed
to take in the TSC as an optional parameter instead of as a
requirement to include the TSC after the hdr field (which we did not
really follow). For now, TSC is not included in the events from
mac80211, but it could be added at some point.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When checking whether or not a given frame needs to be
moved to be properly aligned to a 4-byte boundary, we
use & 4 which wasn't intended, this code should check
the lowest two bits.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently rx status for frames which are completed from reorder buffer
is taken from it's cb area which is not always right, cb is not holding
the rx status when driver uses mac80211's non-irq rx handler to pass it's
received frames. This results in dropping almost all frames from reorder
buffer when security is enabled by doing double decryption (first in hw,
second in sw because of wrong rx status). This patch copies rx status into
cb area before the frame is put into reorder buffer. After this patch,
there is a significant improvement in throughput with ath9k + WPA2(AES).
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous patch ("mac80211: remove mixed-cell and userspace MLME code")
was too obvious to me, so obvious that a stupid bug crept in. The IBSS
RX function must be invoked for IBSS, of course, not anything != IBSS.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Separate beacon and rx path tracking in preparation for the beacon filtering
support. At the same time change ieee80211_associated() to look a bit simpler.
Probe requests are now sent only after IEEE80211_PROBE_IDLE_TIME, which
is now set to 60 seconds.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the timer is triggering every two seconds
(IEEE80211_MONITORING_INTERVAL). Decrease the timer to only trigger during
data idle periods to avoid waking up CPU unnecessary. The timer will
still trigger during idle periods, that needs to be fixed later.
There's also a functional change that probe requests are sent only when the
data path is idle, earlier they were sent also while there was activity
on the data path.
This is also preparation for the beacon filtering support. Thanks to
Johannes Berg for the idea.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Neither can currently be set from userspace, so there's no
regression potential, and neither will be supported from
userspace since the new userspace APIs allow the SME, which
is in userspace, to control all we need.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Radiotap was updated to include a "bad PLCP" flag and standardise
the "bad FCS" flag in the "flags" rather than "RX flags" field,
this patch updates Linux to that standard.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch splits out the ibss code and data from managed (station) mode.
The reason to do this is to better separate the state machines, and have
the code be contained better so it gets easier to determine what exactly
a given change will affect, that in turn makes it easier to understand.
This is quite some churn, especially because I split sdata->u.sta into
sdata->u.mgd and sdata->u.ibss, but I think it's easier to maintain that
way. I've also shuffled around some code -- null function sending is only
applicable to managed interfaces so put that into that file, some other
functions are needed from various places so put them into util, and also
rearranged the prototypes in ieee80211_i.h accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can only support aggregation on AP/STA right now. HT isn't defined
for IBSS, WDS or MESH. In the WDS/MESH cases it's not clear what to
put into the IBSS field, and we don't handle that in the code at all.
Also fix the code to handle VLAN correctly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The values are in TUs (1.024ms), not ms.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's a little confusing to get the BSSID outside the function
and pass it in, when it's only needed for this function, so
change that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a directed tim bit is set, mac80211 currently disables power save
ands sends a null frame to the AP. But if dynamic power save is
disabled, mac80211 will not enable power save ever gain. Fix this by
adding ps-poll functionality to mac80211. When a directed tim bit is
set, mac80211 sends a ps-poll frame to the AP and checks for the more
data bit in the returned data frames.
Using ps-poll is slower than waking up with null frame, but it's saves more
power in cases where the traffic is low. Userspace can control if either
ps-poll or null wakeup method is used by enabling and disabling dynamic
power save.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Giving the signal in dB isn't much more useful to userspace
than giving the signal in unspecified units. This removes
some radiotap information for zd1211 (the only driver using
this flag), but it helps a lot for getting cfg80211-based
scanning which won't support dB, and zd1211 being dB is a
little fishy anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the IEEE80211_RADIOTAP_RATE flag was moved to be conditional, it
was mistakenly left without cpu_to_le32(). Fix that.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is only used within rx.c, so mark it static.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ieee80211_drop_unencrypted() to decide whether a received frame
should be dropped with management frames, too. If MFP is negotiated,
unprotected robust management frames will be dropped.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Process SA Query Requests for client mode in mac80211. AP side
processing of SA Query Response frames is in user space (hostapd).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add mechanism for managing BIP keys (IGTK) and integrate BIP into the
TX/RX paths.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not all drivers are capable of passing properly aligned frames,
in particular with mesh networking no hardware will support
completely aligning it correctly.
This patch adds code to align the data payload to a 4-byte
boundary in memory for those platforms that require this, or
when CONFIG_MAC80211_DEBUG_PACKET_ALIGNMENT is set.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move to the advertised channel on reception of
a CSA element. This is needed for 802.11h compliance.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
