According to SD spec 3.00 3.6.1 signal voltage switch
procedure step 6~8,
(6) Set 1.8V Signal Enable in the Host Control 2 register.
(7) Wait 5ms. 1.8V voltage regulator shall be stable within this period.
(8) If 1.8V Signal Enable is cleared by Host Controller, go to step (12).
Host should wait 5ms after set 1.8V signal enable bit in
Host Control 2 register and check if 1.8V is stable or not.
But current code checks this bit right after set it.
On some platforms with xenon controller found the bit is
cleared right away and host reports "1.8V regulator output
did not became stable" and 5ms delay can help.
Implement voltage_switch callback for xenon controller to add 5ms
delay to make sure the 1.8V signal enable bit is set by controller.
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Without this patch the kernel hand during boot if the mvpp2.2 network
driver was not present in the kernel. Indeed the clock needed by the
xenon controller was set by the network driver.
Fixes: 3a3748dba8 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core
functionality)"
CC: Stable <stable@vger.kernel.org>
Tested-by: Zhoujie Wu <zjwu@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable runtime pm support for xenon controller, which uses 50ms
auto runtime suspend by default.
Reimplement system standby based on runtime pm API.
Introduce restore_needed to restore the Xenon specific registers
when resume.
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Xenon sdh controller requests proper SD bus voltage select
bits programmed even with vmmc power supply. Any reserved
value(100b-000b) programmed in this field will lead to controller
ignore SD bus power bit and keep its value at zero.
Add set_power callback to handle this.
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: 3a3748dba8 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add Xenon specific system-level suspend and resume support.
Especially during resume, re-configure Xenon specific registers
since registers setting will be lost in suspend if Xenon is power off.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was never used and leave a long standing compile warning:
drivers/mmc/host/sdhci-xenon.c: In function 'xenon_probe':
drivers/mmc/host/sdhci-xenon.c:447:21: warning: variable 'priv' set but
not used [-Wunused-but-set-variable]
Remove it to fix the warning.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, the xenon_clean_phy() is only used for freeing phy_params.
The phy_params is allocated by devm_kzalloc(), there's no need to free
is explicitly.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Hu Ziji <huziji@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
sdhci_remove_host() might execute SOFT_RESET_ALL. Inside xenon_remove(),
Xenon SDHC should be enabled during sdhci_remove_host().
Move xenon_sdhc_unprepare after sdhci_remove_host() such that Xenon SDHC is
disabled after sdhci_remove_host() completes.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Reported-by: Jisheng Zhang <jszhang@marvell.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some SoCs have PHY PAD outside Xenon IP.
PHY PAD voltage should match signalling voltage in use.
Add generic SoC PHY PAD voltage control interface.
Implement Aramda-3700 SoC PHY PAD voltage control.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Tested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Marvell Xenon eMMC/SD/SDIO Host Controller contains PHY.
Multiple types of PHYs are supported.
Add support to multiple types of PHYs init and configuration.
Add register definitions of PHYs.
Xenon PHY cannot fit in kernel common PHY framework.
Xenon SDHC PHY register is a part of Xenon SDHC register set.
Besides, MMC initialization has to call several PHY functions to
complete timing setting.
Those PHY setting functions have to access SDHC registers and know
current MMC setting, such as bus width, clock frequency and
speed mode.
As a result, implement Xenon PHY in MMC host directory.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add Xenon eMMC/SD/SDIO host controller core functionality.
Add Xenon specific initialization process.
Add Xenon specific mmc_host_ops APIs.
Add Xenon specific register definitions.
Add CONFIG_MMC_SDHCI_XENON support in drivers/mmc/host/Kconfig.
Marvell Xenon SDHC conforms to SD Physical Layer Specification
Version 3.01 and is designed according to the guidelines provided
in the SD Host Controller Standard Specification Version 3.00.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
