dmaengine_terminate_all() is deprecated and should be replaced by
dmaengine_terminate_sync() in non-atomic context or dmaengine_terminate_async()
with dmaengine_synchronize().
See commit b36f09c3c4 ("dmaengine: Add transfer termination synchronization support")
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 761ed4a945 ("tty: serial_core: convert uart_close to use
tty_port_close") refactored uart_close() to use tty_port_close(). At the same
time it introduced a potential NULL pointer dereference. Rearrange the code to
avoid kernel crash.
Fixes: 761ed4a945 ("tty: serial_core: convert uart_close to use tty_port_close")
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 18dfef9c7f ("serial: atmel: convert to irq handling
provided mctrl-gpio"), interrupts from GPIOs are not disabled any more
when the serial port is closed, leading to an oops when the one of the
input pin is toggled (CTS/DSR/DCD/RNG).
This is only the case if those pins are used as GPIOs, i.e. declared
like that:
usart1: serial@f8020000 {
/* CTS and DTS will be handled by GPIO */
status = "okay";
rts-gpios = <&pioB 17 GPIO_ACTIVE_LOW>;
cts-gpios = <&pioB 16 GPIO_ACTIVE_LOW>;
dtr-gpios = <&pioB 14 GPIO_ACTIVE_LOW>;
dsr-gpios = <&pioC 31 GPIO_ACTIVE_LOW>;
rng-gpios = <&pioB 12 GPIO_ACTIVE_LOW>;
dcd-gpios = <&pioB 15 GPIO_ACTIVE_LOW>;
};
That's because modem interrupts used to be freed in atmel_shutdown().
After commit 18dfef9c7f ("serial: atmel: convert to irq handling
provided mctrl-gpio"), this code was just removed.
Calling atmel_disable_ms() disables the interrupts and everything works
fine again.
Tested on at91sam9g35-cm
(This patch doesn't apply on -stable kernels, fixes for 4.4 and 4.7 will
be sent after this one is applied.)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Fixes: 18dfef9c7f ("serial: atmel: convert to irq handling provided mctrl-gpio")
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function lpuart_start_rx_dma() is called from several
places, in some of which, such as lpuart_startup(), a lock
be held here, so we should use GFP_ATOMIC when a lock is held.
Fixes: 5887ad43ee ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dev.of_node is not NULL, we also need to set IRQF_TRIGGER_FALLING
flag, otherwise it may cause uncertain interrupts.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guenter Roeck reported a regression caused by commit "serial: earlycon:
Extend earlycon command line option to support 64-bit addresses":
console= and earlycon= options have the following format:
...,<addr>,<options>
Historically used here simple_strtoul() had no problems with comma, but the
new and recommended kstrtoull() requires null-terminated string and returns
-EINVAL in case there are "options" at the end. There is no recommended to
use function currently that will support it, so stick to obsolete
simple_strtoull() variant.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some functions called by serial_imx_probe emit an error message themself
(like kmalloc() and friends). clk_prepare_enable() and
devm_request_irq() however don't which might make the driver silently
fail to probe. So add an error message for these.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have nice macro IRQ_RETVAL() we would use it to convert a flag of
handled interrupt from int to irqreturn_t.
The rationale of doing this is:
a) hence we implicitly mark hsu_dma_do_irq() as an auxiliary function that
can't be used as interrupt handler directly, and
b) to be in align with serial driver which is using serial8250_handle_irq()
that returns plain int by design.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
earlycon implementation used "unsigned long" internally, but there are systems
(ARM with LPAE) where sizeof(unsigned long) == 4 and uart is mapped beyond 4GiB
address range.
Switch to resource_size_t internally and replace obsoleted simple_strtoul() with
kstrtoull().
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We get 1 warning when building kernel with W=1:
drivers/tty/serial/earlycon-arm-semihost.c:56:12: warning: no previous prototype for 'early_smh_setup' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ACPI identifier for UART on Hisilicon Hip05 SoC, be careful that
it is not 16550 compatible, and "reg-io-width" and "reg-shift" need
be set properly by _DSD method in DSDT.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify the check of em485 variable to be either (em485) or (!em485) instead of
the explicit comparison to NULL.
While here, remove redundant check in __do_stop_tx_rs485() and
__stop_tx_rs485() since the functions ain't called with NULL value of em485
variable.
Cc: "Matwey V. Kornilov" <matwey@sai.msu.ru>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are calls to serial8250_rpm_{get|put}() in __do_stop_tx_rs485() that are
certainly placed in a wrong location. I dunno how it had been tested with
runtime PM enabled because it is obvious "sleep in atomic context" error.
Besides that serial8250_rpm_get() is called immediately after an IO just
happened. It implies that the device is already powered on, see implementation
of serial8250_em485_rts_after_send() and serial8250_clear_fifos() for the
details.
There is no bug have been seen due to, as I can guess, use of auto suspend mode
when scheduled transaction to suspend is invoked quite lately than it's needed
for a few writes to the port. It might be possible to trigger a warning if
stop_tx_timer fires when device is suspended.
Refactor the code to use runtime PM only in case of timer function.
Fixes: 0c66940d58 ("tty/serial/8250: fix RS485 half-duplex RX")
Cc: "Matwey V. Kornilov" <matwey@sai.msu.ru>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART DMA was only being configured on i.MX6Q compatible devices. We
know that the DMA also works for i.MX53 devices, so enable uart DMA for
imx53 and let the device tree to configure if DMA should be used or not.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use an unified new dev variable instead of &pdev->dev and p->dev
in probe function.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added devices ids for acces i/o products quad and octal serial cards
that make use of existing Pericom PI7C9X7954 and PI7C9X7958
configurations .
Signed-off-by: Jimi Damon <jdamon@accesio.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update error counters when DMA is used for receiving data. Do
this by using DMA transaction error event instead error interrupts
to reduce interrupt load.
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IMX UART has a 32 bytes HW buffer which can be filled up in
2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53).
Taking this in consideration there is a good probability to lose
data because of the DMA startup latency.
Our tests (explained below) indicates a latency up to 4400us when
creating interrupt load and ~70us without. When creating interrupt
load I was able to see continuous overrun errors by checking serial
driver statistics using the command:
`cat /proc/tty/driver/IMX-uart`.
Replace manual restart of DMA with cyclic DMA to eliminate data loss
due to DMA engine startup latency (similar approch to atmel_serial.c
driver). As result the DMA engine will start on the first serial data
transfer and stops only when serial port is closed.
Tests environment:
Using the m53evk board I have used a GPIO for profiling the IMX
serial driver.
- The RX line and GPIO were connected to oscilloscope.
- Run a small test program on the m53evk board that will only open
and read data from ttymxc2 port.
- Connect the ttymxc2 port to my laptop using a USB serial converter
where another test program is running, able to send configurable
packet lengths and intervals.
- Serial ports configured at 115200 8N1.
- Interrupts load created by disconnecting/connecting (3s interval)
a USB hub, using a digital switch, with 4 USB devices (USB-Serial
converter, USB SD card, etc) connected.
(around 160 interrupts/second generated)
- The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM
events are received and toggled back, once the DMA configuration
is finalized, at the end of `imx_dma_rxint`.
Measurements:
The measurements were done from the end of the last byte (RX line) until
the GPIO was toggled back LOW.
Note: The GPIO toggling was done using `gpiod_set_value` method.
Tests performed:
1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets
will activate the RRDY threshold event and IMX serial interrupt
called.
Results:
- DMA start latency (interrupt start latency +
DMA configuration) consistently 70us when system not loaded.
- DMA start latency up to 4400us when system loaded.
2. Sending 40 bytes packet at 8mS interval.
Results with load:
- Able to observe overruns by running:
`watch -n1 cat /proc/tty/driver/IMX-uart`
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA on Intel Quark SoC is a part of UART IP block. Enable it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SoCs, such as Intel Braswell, have DesignWare UART IP. Split out the
support of such chips to a separate module which also will be used for Intel
Quark later.
The rationale to have the separate driver to be existing:
- Do not contaminate 8250_pci.c anymore with LPSS related quirks
- All of them are using same DMA engine and they are Designware IP which means
that in the future we might share the code between 8250_dw.c and 8250_lpss.c
- It reduces the kernel memory footprint on non-X86 machines where 8250_pci.c
is in use
Besides the split the driver also has been refactored, in particular a) the DMA
and port setup are separate functions, b) the two new structures lpss8250 and
lpss8250_board are introduced to keep necessary data instead of
pciserial_board, c) DMA parameters are passed to the DMA setup via mentioned
custom structure. Most of the changes are done due to the future support of
UART DMA on Intel Quark.
The Intel Quark UART DMA support is based on bits taking from BSP code
published by Intel earlier.
The driver does not use any specific power management. PCI core takes care of
the default behaviour during suspend and resume.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Quark has 16550A compatible UART with autoflow feature enabled. It has
only 16 bytes of FIFO. Currently serial8250_do_set_termios() prevents to enable
autoflow since the minimum requirement of 32 bytes of FIFO size.
Drop a FIFO size limitation to allow autoflow control be enabled on such UARTs.
While here, comment out UART_CAP_AFE for PORT_AR7 since it wasn't working and
it will be not a good idea to use it in conjunction with trigger level of 1
byte.
Suggested-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some UARTs, e.g. one is used in Intel Quark, have a different address base for
DMA operations. Introduce an additional field (per RX and TX DMA channels) in
struct uart_8250_dma to cover those cases.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert dmaengine_terminate_all() calls to synchronous and asynchronous
versions where appropriate.
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously sc16is7xx_power was called in order to set the device to a
low power mode.
However since SC16IS7XX_EFR_ENABLE_BIT was not set beforehand this
suspend request had not effect.
Also, soft-reset the device prior to port initialization. It may
otherwise be in a state (interrupt pending, fifo not empty) which
prevents it from sleeping.
Signed-off-by: Florian Vallee <fvallee@eukrea.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mediatek can support baud rate up to 4M.
the 'uart_get_baud_rate' function will limit the max baud rate.
Modify max baud to remove the limit.
Signed-off-by: Long Cheng <long.cheng@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2;
statement S2,S1;
@@
- if (of_get_property(e1,e2,NULL))
+ if (of_property_read_bool(e1,e2))
S1 else S2
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the commit c1a67b48f6 ("serial: 8250_pci: replace switch-case by
formula for Intel MID"), the 8250 driver crashes in the byt_set_termios()
function with a divide error. This is caused by the fact that a baud rate of 0
(B0) is not handled properly. Fix it by falling back to B9600 in this case.
Reported-by: "Mendez Salinas, Fernando" <fernando.mendez.salinas@intel.com>
Fixes: c1a67b48f6 ("serial: 8250_pci: replace switch-case by formula for Intel MID")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable Vybrid's build-in support for RS-485 auto RTS for controlling line
direction of RS-485 transceiver driver.
Enable RS485 feature by either using ioctrl 'TIOCSRS485' or enable it in the
device tree by setting 'linux,rs485-enabled-at-boot-time' property.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DMA mode is enabled one need to make sure the DMA channels are idle before
entering suspend mode especially when UART ports which are set as wakeup source
and console port with no_console_suspend is set. This patch takes care of
gracefully releasing DMA channels for the above two cases and start the DMA at
resume.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop PIO to DMA switching and use scatter/gather DMA for Tx path to improve
performance.
Some part of the code is borrowed from imx serial driver.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The initial approach of DMA implementatin for RX is inefficient due to switching
from PIO to DMA, this leads to overruns especially on instances with the smaller
FIFO. To address these issues this patch uses a cyclic DMA for receiver path.
Some part of the code is borrowed from atmel serial driver.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default the driver always configure the mode as 8s1 even when 8m1 mode is
selected. Fix this by adding support to control the space/mark bit.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8e4934c6d6 ("tty: serial: fsl_lpuart: clear receive flag on FIFO
flush") implemented clearing of the receive flag by reading the status register
only. It turned out that even though we flush the FIFO afterwards, a explicit
read of the data register is still required.
This leads to a FIFO underrun. To avoid this, follow the advice in the overrun
"Operation section": Unconditionally clear RXUF after using RXFLUSH.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the tx_empty callback only considers the Transmit Complete Flag (TC).
The reference manual is not quite clear if the TC flag covers the TX FIFO too.
Debug prints on real hardware have shown that from time to time the TC flag is
asserted (indicating Transmitter idle) while there are still data in the
TX FIFO. Hence, in this case the serial core will call the shutdown callback
even though there are data remaining in the TX FIFO buffers.
Avoid early shutdowns by considering the TX FIFO empty flag too. Also avoid
theoretical race conditions between DMA and the driver by checking whether the
TX DMA is in progress too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should check the data->pclk, not data->clk when get apb_pclk.
Fixes: c8ed99d4f6a8("serial: 8250_dw: Add support for deferred probing")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
