On the i.MX SPI driver the chipselect pins can be of the following types:
- internal: when the chipselect pin is used as a dedicated CS pin of the CSPI controller
- GPIO: a generic GPIO can be used as a chipselect funtion
On the mx27_3ds the SPI2 chip select is a GPIO, so don't annotate 'internal' in the chip select
definition.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use the standard gpio_to_irq function instead of a dedicated IRQ_GPIOx macro.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Place the UART gpio initialization inside the scb9328_init function as it is done on
other i.MX boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As no flag is passed into UART0 platform data, pass NULL argument
when registering UART0.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are several occurences where MXC_INTERNAL_IRQ is
assumed to be the start of the gpio interrupts. It was never
meant this way. Replace these with gpio_to_irq.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
We have a clocksource which renders CLOCK_TICK_RATE useless. Define
it to a bogus value to get rid of some ifdeffery.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This allows to move the led definition to .init.rodata.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This gets rid of per machine struct platform_device definitions and allows
to move the platform data and led definition to .init.rodata.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This gets rid of per machine struct platform_device definitions and allows
to move the platform data and led definition to .init.rodata.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Instead of using gpio_request followed by gpio_direction_output use gpio_request_array
when requesting multiple pins.
Also fixed the location of the delay for the reset and make the BABBAGE_USB_PHY_RESET to toggle.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The USB PHY Reset GPIO can be configured in the same place as the other GPIOs.
While at it rename the pin as BABBAGE_USB_PHY_RESET to make clearer its purpose.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
", o" was used for ", 0"
", 17" was used for ", 7 | 0x10"
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The clock from which the I2C timing is derived is the ipg_perclk not ipg_clk.
I2C bus frequency was lower by a factor of ~8 due to the clock divider
calculation being based on 66.5MHz IPG clock while the bus actually
uses 8MHz ipg_perclk.
Kernel version: 3.0.0-rc2 branch 'imx-for-next' of git://git.pengutronix.de/git/imx/linux-2.6
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The pins are actually used (not in mainline yet):
D4 -> SSP2_D0
D5 -> GPIO
D6 -> GPIO
D7 -> GPIO for owire
so their pinmapping for SSP0 is wrong.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Mark the actual interrupt source for some interrupts currently marked as reserved.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
iomux-v3.c uses NO_PAD_CTRL as a 32 bit value
so it should not be shifted left by MUX_PAD_CTRL_SHIFT(41)
Previously, anything requesting NO_PAD_CTRL would get
their pad control register set to 0.
Since it is a pad control mask, place it with the other mask values.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On MX51 the address space length for SSI is 16KB.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The imx25 sdma script only gets TO1 version, so there is no need
to encode "to1" in the variable name.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The value 0 is not a valid TO version number. With the current
code, imx-sdma driver will try to load firmware sdma-imx25-to0.bin,
which is obviously not a good name. Instead, sdma-imx25-to1.bin
makes much more sense.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix the following warning:
CC arch/arm/plat-mxc/iomux-v1.o
arch/arm/plat-mxc/iomux-v1.c: In function 'mxc_gpio_setup_multiple_pins':
arch/arm/plat-mxc/iomux-v1.c:160: warning: 'ret' may be used uninitialized in this function
arch/arm/plat-mxc/iomux-v1.c:160: note: 'ret' was declared here
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix the 2.8V (VMMC1) and 1.8V (VGEN) voltage generation on mx27_3ds.
Also configure the IOMUX for the PMIC interrupt pin and for the CSPI chip select that is connected
to the MC13783 PMIC.
In order to get the voltage for the LCD (2.8V and 1.8V) it is also necessary to turn on GPO1 and GPO3
supplies because they are connected to switches that enable these two voltages.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When setting the IOMUX of multiple pins via mxc_gpio_setup_multiple_pins, gpio_request
is called and this prevents subsequent calls of gpio_request done by drivers to succeed.
Remove gpio_request call from mxc_gpio_setup_multiple_pins function.
As gpio_request is removed from mxc_gpio_setup_multiple_pins, there is no need to have
mxc_gpio_release_multiple_pins anymore, so remove this function.
Tested on a mx27_3ds board and after applying this patch it is possible to define all the
IOMUX setup in a static array
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Original code was assuming that the CSPI1 pins on the
MX31PDK were the primary pin function, which is incorrect.
On MX31PDK board these are the pins that provide CSPI1 functionality:
DSR_DCE1 (ALT mode 1) --> CSPI1_CLK
RI_DCE1 (ALT mode 1) --> CSPI1_RDY
DTR_DTE1 -->CSI1_MOSI
DSR_DTE1 --> CSPI1_MISO
DTR_DCE2 ---> CSPI1_SS2
The 3 IOMUX settings above are done via GPR as per Table A-1 of the MX31RM.
This patch fixes the CSPI1 IOMUX and makes the LCD to be functional.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Let USB Storage be built by default.
Also select NLS_ISO8859 so that the USB device can be mounted.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The patch fixes the warning below.
arch/arm/configs/mxs_defconfig:92:warning: symbol value 'm' invalid for RTC_CLASS
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The DGT runs at 27 MHz divided by 4 on 8660 and 8960.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Some msm targets have timers whose lower bits are unreliable. So, we
present our timers as lower frequency than they actually are, and ignore
the bottom 5 bits on such targets. This compensation was erroneously
removed from the msm_read_timer_count function, so restore it.
This was broken by 94790ec25 "msm: timer: SMP timer support for msm".
Signed-off-by: Jeff Ohlstein <johlstei@codeaurora.org>
* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
gpio: add GPIOF_ values regardless on kconfig settings
gpio: include linux/gpio.h where needed
gpio/omap4: Fix missing interrupts during device wakeup due to IOPAD.
* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
spi/bfin_spi: fix handling of default bits per word setting
Some files use GPIOF_ macros but don't include the header file
for them. These macros are being moved to <linux/gpio.h>, so add
includes for <linux/gpio.h> where needed.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: footbridge: fix clock event support
ARM: footbridge: fix debug macros
ARM: initrd: disable initrds outside of memory
ARM: extend Code: line by one 16-bit quantity for Thumb instructions
ARM: 6955/1: cmpxchg syscall should data abort if page not write
ARM: 6954/1: zImage: fix Thumb2 breakage
ARM: 6953/1: DT: don't try to access physical address zero
ARM: 6949/2: mach-u300: fix compilaton warning in IO accessors
Revert "ARM: 6944/1: mm: allow ASID 0 to be allocated to tasks"
Revert "ARM: 6943/1: mm: use TTBR1 instead of reserved context ID"
davinci: make PCM platform devices static
arm: davinci: Fix fallout from generic irq chip conversion
ARM: 6894/1: mmci: trigger card detect IRQs on falling and rising edges
ARM: 6952/1: fix lockdep warning of "unannotated irqs-off"
ARM: 6951/1: include .bss in memory layout information
ARM: 6948/1: Fix .size directives for __arm{7,9}tdmi_proc_info
ARM: 6947/2: mach-u300: fix compilation error in timer
ARM: 6946/1: vexpress: move v2m clock init to init_early
ARM: mx51/sdma: Check the chip revision in run-time
arm: mxs: include asm/processor.h for cpu_relax()
