The attribute country_code and alpha2 are two different attributes in
the sprom. country_code contains some code in an 8 bit coding and
alpha2 contains two chars with the country code. The attributes where
read out wrongly in the past and country_code is only available on
sprom version 1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the rev contained the revision read from the pci config
space and was used as board_rev in the wireless drivers. This is wrong
the board_rev is only fetched from the sprom accordingly to the open
source part of the Broadcom SDK and brcmsmac. This patch removes the
rev from the boardinfo structure and uses the board_rev attribute from
sprom instead. This attribute is filled by PCI, PCMCIA, SDIO and SoC
code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull networking merge from David Miller:
"1) Move ixgbe driver over to purely page based buffering on receive.
From Alexander Duyck.
2) Add receive packet steering support to e1000e, from Bruce Allan.
3) Convert TCP MD5 support over to RCU, from Eric Dumazet.
4) Reduce cpu usage in handling out-of-order TCP packets on modern
systems, also from Eric Dumazet.
5) Support the IP{,V6}_UNICAST_IF socket options, making the wine
folks happy, from Erich Hoover.
6) Support VLAN trunking from guests in hyperv driver, from Haiyang
Zhang.
7) Support byte-queue-limtis in r8169, from Igor Maravic.
8) Outline code intended for IP_RECVTOS in IP_PKTOPTIONS existed but
was never properly implemented, Jiri Benc fixed that.
9) 64-bit statistics support in r8169 and 8139too, from Junchang Wang.
10) Support kernel side dump filtering by ctmark in netfilter
ctnetlink, from Pablo Neira Ayuso.
11) Support byte-queue-limits in gianfar driver, from Paul Gortmaker.
12) Add new peek socket options to assist with socket migration, from
Pavel Emelyanov.
13) Add sch_plug packet scheduler whose queue is controlled by
userland daemons using explicit freeze and release commands. From
Shriram Rajagopalan.
14) Fix FCOE checksum offload handling on transmit, from Yi Zou."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1846 commits)
Fix pppol2tp getsockname()
Remove printk from rds_sendmsg
ipv6: fix incorrent ipv6 ipsec packet fragment
cpsw: Hook up default ndo_change_mtu.
net: qmi_wwan: fix build error due to cdc-wdm dependecy
netdev: driver: ethernet: Add TI CPSW driver
netdev: driver: ethernet: add cpsw address lookup engine support
phy: add am79c874 PHY support
mlx4_core: fix race on comm channel
bonding: send igmp report for its master
fs_enet: Add MPC5125 FEC support and PHY interface selection
net: bpf_jit: fix BPF_S_LDX_B_MSH compilation
net: update the usage of CHECKSUM_UNNECESSARY
fcoe: use CHECKSUM_UNNECESSARY instead of CHECKSUM_PARTIAL on tx
net: do not do gso for CHECKSUM_UNNECESSARY in netif_needs_gso
ixgbe: Fix issues with SR-IOV loopback when flow control is disabled
net/hyperv: Fix the code handling tx busy
ixgbe: fix namespace issues when FCoE/DCB is not enabled
rtlwifi: Remove unused ETH_ADDR_LEN defines
igbvf: Use ETH_ALEN
...
Fix up fairly trivial conflicts in drivers/isdn/gigaset/interface.c and
drivers/net/usb/{Kconfig,qmi_wwan.c} as per David.
There is no 2.4 GHz or 5GHz antenna gain stored in sprom. The sprom
just stores the gain values for antenna 1 and 2 or 1 to 4 for more
recent sprom versions. On old devices antenna 2 was used for 5 GHz wifi.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support the the BCM5354 SoC.
It has a PMU and a constant not configurable clock.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes us see what type of hardware someone uses by the dmesg
output.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ssb supports one extra device on the cardbus. This results in two
devices in total, one beeing the host controller itself and the other
the external device connected to the hostcontroller over cardbus.
This makes the cardbus slot work on the Linksys WRT150N.
Reported-by: Aaron Z <aaronz@pls-net.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the removal of get_driver()/put_driver(), this patch
(as1512) gets rid of various useless and unnecessary calls in several
drivers. In some cases it may be desirable to pin the driver by
calling try_module_get(), but that can be done later.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: "David S. Miller" <davem@davemloft.net>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Michael Buesch <m@bues.ch>
CC: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We already extract some basic info but it's incomplete, reads info
about the first core only. Used data structure doesn't allow easy
adding of more cores.
This patch adds new struct and array for storing power info. The plan
is to: switch all extractors (including the ones using NVRAM) to new
struct, switch drivers, then deprecate and finally drop old SSB fields.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a Data bus error on some SoCs. The first fix for this
problem did not solve it on all devices.
commit 6ae8ec2786
Author: Rafał Miłecki <zajec5@gmail.com>
Date: Tue Jul 5 17:25:32 2011 +0200
ssb: fix init regression of hostmode PCI core
In ssb_pcicore_fix_sprom_core_index() the sprom on the PCI core is
accessed, but the sprom only exists when the ssb bus is connected over
a PCI bus to the rest of the system and not when the SSB Bus is the
main system bus. SoCs sometimes have a PCI host controller and there
this code will not be executed, but there are some old SoCs with an PCI
controller in client mode around and ssb_pcicore_fix_sprom_core_index()
should not be called on these devices too. The PCI controller on these
devices are unused, but without this fix it results in an Data bus
error when it gets initialized.
Cc: Michael Buesch <m@bues.ch>
Cc: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Or we will get things like this when we remove the implicit path:
drivers/ssb/embedded.c:32: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
drivers/ssb/driver_chipcommon.c:432: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
drivers/ssb/driver_chipcommon_pmu.c:607: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
drivers/ssb/pcihost_wrapper.c:120: error: ‘THIS_MODULE’ undeclared (first use in this function)
drivers/ssb/driver_pcicore.c:721: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
drivers/ssb/driver_gige.c:249: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The header cleanup means that module.h is no longer simply
everywhere. So real modules need to actively include it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
Remove b43's workarounds at the same time. Other users of
ssb_dma_translation do not support any 64-bit DMA devices, so they are
not affected.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SSB code reads PCI subsystem IDs from the PCI configuration registers while
they are already stored by the PCI subsystem in the 'subsystem_{vendor|device}'
fields of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SSB code reads PCI revision ID from the PCI configuration register while
it's already stored by the PCI subsystem in the 'revision' field of 'struct
pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SSB code reads PCI revision ID register as 16-bit entity while the register
is actually 8-bit only (the next 8 bits are the programming interface register).
Fix the read and make the 'rev' field of 'struct ssb_boardinfo' 8-bit as well,
to match the register size.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bus scan code reads PCI revision ID from the PCI configuration register
while it's already stored by PCI subsystem in the 'revision' field of 'struct
pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fix was done according to si_clock_rate function in broadcom siutils.c
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Two functions in ssb are using register_pci_controller() which is
__devinit. The functions ssb_pcicore_init_hostmode() and
ssb_gige_probe() should also be __devinit.
This fixes the following warning:
WARNING: vmlinux.o(.text+0x2727b8): Section mismatch in reference from the function ssb_pcicore_init_hostmode() to the function .devinit.text:register_pci_controller()
The function ssb_pcicore_init_hostmode() references
the function __devinit register_pci_controller().
This is often because ssb_pcicore_init_hostmode lacks a __devinit
annotation or the annotation of register_pci_controller is wrong.
WARNING: vmlinux.o(.text+0x273398): Section mismatch in reference from the function ssb_gige_probe() to the function .devinit.text:register_pci_controller()
The function ssb_gige_probe() references
the function __devinit register_pci_controller().
This is often because ssb_gige_probe lacks a __devinit
annotation or the annotation of register_pci_controller is wrong.
Reported-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
warning message
drivers/ssb/driver_chipcommon_pmu.c: In function ssb_pmu_resources_init
drivers/ssb/driver_chipcommon_pmu.c:420:15: warning: updown_tab_size may
be used uninitilized in this function.
updown_tab_size and depend_tab_size may not be set in the bus->chip_id
switch statement, so set to 0 by default to avoid using uninitialized
stack space.
Signed-off-by: Connor Hansen <cmdkhh@gmail.com>
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were incorrectly executing PCIe specific workarounds on PCI cards.
This resulted in:
Machine check in kernel mode.
Caused by (from SRR1=149030): Transfer error ack signal
Oops: Machine check, sig: 7 [#1]
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
Some embedded devices like the Netgear WNDR3300 have two SSB based cards
without an own sprom on the pci bus. We have to provide two different
fallback sproms for these and this was not possible with the old solution.
In the bcm47xx architecture the sprom data is stored in the nvram in the
main flash storage. The architecture code will be able to fill the sprom
with the stored data based on the bus where the device was found.
The bcm63xx code should do the same thing as before, just using the new
API.
Acked-by: Michael Buesch <mb@bu3sch.de>
Cc: netdev@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2362/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/ssb/main.c:1336: error: 'SSB_PCICORE_BCAST_ADDR' undeclared (first use in this function)
drivers/ssb/main.c:1337: error: 'SSB_PCICORE_BCAST_DATA' undeclared (first use in this function)
drivers/ssb/main.c:1349: error: 'struct ssb_pcicore' has no member named 'dev'
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commiting settings is possible on devices without PCI core (but with CC
core). Export it for usage in drivers supporting other cores.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the BCM43xx chips contain cores that are attached to the SSB, but are
inactive as they do not connect to the external environment. These must not be
registered. Several of these types are handled in driver ssb; however, the
specific case of an inactive 802.11 cores is now treated in b43 and b43legacy.
Although the current setup works, this minor change will place all such
workarounds in ssb, and simplify the code in drivers b43 and b43legacy.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My 14e4:4315 is SSB_IDLOW_SSBREV_26:
read32 0xfaafcff8 -> 0x600422d5
My 14e4:4328 is SSB_IDLOW_SSBREV_24:
read32 0xfaafcff8 -> 0x400422c5
My 14e4:432b is SSB_IDLOW_SSBREV_26 again:
read32 0xfaafcff8 -> 0x600422d5
For all of them wl driver is using 0x2 reject bit:
write32(0xf98) <- 0x00010002
So it seems SSB 2.3 is the exception using another bit.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ssb_chipco_set_clockmode may want to touch CC registers to control power of the
bus. However touching registers without powered_up set causes warnings.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Default min_msk on my 0x4312 is 0x80000CBB, not 0xCBB. Now we follow
specs and wl (noticed in MMIO dumps).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ssb_wait_bit was designed for only one-bit bitmasks.
People start using it for multi-bit bitmasks. Make the "set" case
is safe for this. The "unset" case is already safe.
This does not change behavior of the current code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes parsing of the device invariants (MAC address)
for PCMCIA SSB devices.
ssb_pcmcia_do_get_invariants expects an iv pointer as data
argument.
Tested-by: dylan cristiani <d.cristiani@idem-tech.it>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some Broadcom based wireless devices contain dangling ethernet cores.
This triggers the ssb probing mechanism and tries to load the b44 driver
on this core.
Ignore the dangling core in the ssb core scanning code to avoid
access to the core and failure of b44 probing.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use function pci_is_pcie() instead of accessing struct member directly.
CC: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make it possible to read out the attributes, till now only show on
dmesg, through sysfs.
This patch was some time in OpenWrt.
Signed-off-by: Bernhard Loos <bernhardloos@googlemail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new vendor for Broadcom 4318.
Signed-off-by: Daniel Klaffenbach <danielklaffenbach@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This hacks leads to incorrect SPROM parsing for me and reading for example MAC
as: 00:00:00:54:00:00. Michael G. who introduced this confirmed it is not
needed anymore.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Michael Gerdau <mgd@qata.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MMIO log traces obtained using the Broadcom wl hybrid driver show that
the RETRY_TIMEOUT register (0x41) in PCI configuration space is cleared
if non-zero. Similar code found in other drivers such as ipw2100 show
this operation is needed to keep PCI Tx retries from interfering with
C3 CPU state. There are no known cases where omission of this code has
caused a problem, but this patch is offered just in case such a situation
occurs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: avoid buffer overflow in pcmcia_setup_isa_irq
pcmcia: do not request windows if you don't need to
pcmcia: insert PCMCIA device resources into resource tree
pcmcia: export resource information to sysfs
pcmcia: use struct resource for PCMCIA devices, part 2
pcmcia: remove memreq_t
pcmcia: move local definitions out of include/pcmcia/cs.h
pcmcia: do not use io_req_t when calling pcmcia_request_io()
pcmcia: do not use io_req_t after call to pcmcia_request_io()
pcmcia: use struct resource for PCMCIA devices
pcmcia: clean up cs.h
pcmcia: use pcmica_{read,write}_config_byte
pcmcia: remove cs_types.h
pcmcia: remove unused flag, simplify headers
pcmcia: remove obsolete CS_EVENT_ definitions
pcmcia: split up central event handler
pcmcia: simplify event callback
pcmcia: remove obsolete ioctl
Conflicts in:
- drivers/staging/comedi/drivers/*
- drivers/staging/wlags49_h2/wl_cs.c
due to dev_info_t and whitespace changes
Now they are unnecessary. We can use the generic DMA API with any bus.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Gary Zambrano <zambrano@broadcom.com>
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add dma_dev, a pointer to struct device, to struct ssb_device. We pass it
to the generic DMA API with SSB_BUSTYPE_PCI and SSB_BUSTYPE_SSB.
ssb_devices_register() sets up it properly.
This is preparation for replacing the ssb bus specific DMA API (ssb_dma_*)
with the generic DMA API.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Michael Buesch <mb@bu3sch.de>
Cc: Gary Zambrano <zambrano@broadcom.com>
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: John W. Linville <linville@tuxdriver.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In kernel Bugzilla #15825 (2 users), in a wireless mailing list thread
(http://lists.infradead.org/pipermail/b43-dev/2010-May/000124.html), and on a
netbook owned by John Linville
(http://marc.info/?l=linux-wireless&m=127230751408818&w=4), there are reports
of ssb failing to detect an SPROM at the normal location. After studying the
MMIO trace dump for the Broadcom wl driver, it was determined that the affected
boxes had a relocated SPROM.
This patch fixes all systems that have reported this problem.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ethernet driver b44 does register ssb by it's pcihost_wrapper
and doesn't set ssb_chipcommon. A check on this value
introduced with commit d53cdbb94a
and ea2db495f9 triggers:
BUG: unable to handle kernel NULL pointer dereference at 00000010
IP: [<c1266c36>] ssb_is_sprom_available+0x16/0x30
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
Instead of the old pcmcia_request_irq() interface, drivers may now
choose between:
- calling request_irq/free_irq directly. Use the IRQ from *p_dev->irq.
- use pcmcia_request_irq(p_dev, handler_t); the PCMCIA core will
clean up automatically on calls to pcmcia_disable_device() or
device ejection.
- drivers still not capable of IRQF_SHARED (or not telling us so) may
use the deprecated pcmcia_request_exclusive_irq() for the time
being; they might receive a shared IRQ nonetheless.
CC: linux-bluetooth@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: linux-usb@vger.kernel.org
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
In kernel Bugzilla #15825, a case where routine ssb_bus_pcibus_register()
fails silently is reported. The cause for the failure is still being
investigated; however, the diagnosis would be easier if the failure
had been reported.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Our offset handling becomes even a little more hackish now. For some reason I
do not understand all offsets as inrelative. It assumes base offset is 0x1000
but it will work for now as we make offsets relative anyway by removing base
0x1000. Should be cleaner however.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Attempting to read registers that don't exist on the SSB bus can cause
hangs on some boxes. At least some b43 devices are 'in the wild' that
don't have SPROMs at all. When the SSB bus support loads, it attempts
to read these (non-existant) SPROMs and causes hard hangs on the box --
no console output, etc.
This patch adds some intelligence to determine whether or not the SPROM
is present before attempting to read it. This avoids those hard hangs
on those devices with no SPROM attached to their SSB bus. The
SSB-attached devices (e.g. b43, et al.) won't work, but at least the box
will survive to test further patches. :-)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Michael Buesch <mb@bu3sch.de>
The SSB PCIcore code reused the IO resource fixup code from the original
2.4.x Broadcom patch for BCM47xx based devices, which was a quick hack
for doing PCI IO resource configuration back then (the boot loader
doesn't configure PCI devices on this platform).
However, this code is no longer necessary since the kernel now can do
PCI resource management fine all by itself, so remove the old code.
When removing the code, it becomes obvious that the mem_offset setting
in the PCIcore driver was wrong, however this was masked by the fixup
code before, except in a few cases involving yenta_socket. For BCM47xx,
the correct offset is 0, and since this is the only device using PCIcore
in host mode, the offset can simply be removed unconditionally.
Signed-off-by: Andreas Ferber <af@chaos-agency.de>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Markus Wigge <markus@cultcom.de>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1070/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The latest changes in the N PHY core require the symbol
ssb_chipco_gpio_control to be exported.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the N PHYs need a revision in the handling of the PMU.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Explicitely enable shared interrupt 2 for any core that didn't get a dedicated IRQ
anymore (fallthrough case) and for EXTIF cores to make gpio interrupts work.
Also remove a bogus comment.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a CONFIG_SSB_SDIOHOST typo.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Reported-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Tested-By: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The range check in the sprom image parser hex2sprom() is broken.
One sprom word is 4 hex characters.
This fixes the check and also adds much better sanity checks to the code.
We better make sure the image is OK by doing some sanity checks to avoid
bricking the device by accident.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SPROM writing routines were broken since we rewrote the suspend
handling on wireless devices, because SPROM writing depended on suspend.
This patch changes it and freezes devices with the driver remove(), probe()
callbacks instead. This also simplifies the whole logics a lot.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At present, the results of an SSB core scan are only logged when
CONFIG_SSB_DEBUG is "y". As this may not be set in a distro kernel,
it is difficult interpret many problems posted in bug reports or in
help forums.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scan function was using 32 bit access which does not
work on 16bit CF cards.
This patch corrects this by doing two 16 bit reads like
ssb_pcmcia_read32 already does.
mb -- Removed locking. That early in init there's no need for locking.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SSB is a prime example of how to make use of the new CIS helpers.
CC: Michael Buesch <mb@bu3sch.de>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Fix printk format warnings:
drivers/ssb/sdio.c:336: warning: format '%u' expects type 'unsigned int', but argument 7 has type 'size_t'
drivers/ssb/sdio.c:443: warning: format '%u' expects type 'unsigned int', but argument 7 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an SPROM revision is not recognized, the code falls back to a V1
SPROM; however, that revision is not forced in the appropriate structure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for communicating with a Sonics Silicon Backplane through a
SDIO interface, as found in the Nintendo Wii WLAN daughter card.
The Nintendo Wii WLAN card includes a custom Broadcom 4318 chip with
a SDIO host interface.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SSB modinit should not succeed, if busattach failed.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement the "PMU LDO set voltage" and "PMU LDO PA ref enable"
functions, and use them during LP-PHY baseband init in b43.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also add a "SPEX32" macro for extracting 32-bit SPROM variables.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
cxgb3: Fix crash caused by stashing wrong netdev_queue
ixgbe: Fix coexistence of FCoE and Flow Director in 82599
memory barrier: adding smp_mb__after_lock
net: adding memory barrier to the poll and receive callbacks
netpoll: Fix carrier detection for drivers that are using phylib
includecheck fix: include/linux, rfkill.h
p54: tx refused but queue active
Atheros Kconfig needs to be dependent on WLAN_80211
mac80211: fix docbook
mac80211_hwsim: avoid NULL access
ssb: Add support for 4318E
b43: Add support for 4318E
zd1211rw: adding SONY IFU-WLM2 (054c:0257) as a zd1211b device
zd1211rw: 07b8:6001 is a ZD1211B
r6040: bump driver version to 0.24 and date to 08 July 2009
r6040: restore MIER register correctly when IRQ line is shared
ipv4: Fix fib_trie rebalancing, part 4 (root thresholds)
davinci_emac: fix kernel oops when changing MAC address while interface is down
igb: set lan id prior to configuring phy
mac80211: minstrel: avoid accessing negative indices in rix_to_ndx()
...
Added support for the Broadcom 4318E chipset on PCMCIA/CF cards. The
4318E can do 802.11A/B/G, only B and G mode are supported in b43.
Signed-off-by: Clyde McPherson <ccmcphe@verizon.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 5fd29d6ccb ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current ssb irq setup in ssb_mipscore_init has the problem that it
configures some device on some irq without checking that the irq is not
taken by an other device.
For example in my case PCI host is on irq 0 and IPSEC on irq 3.
The current code:
- store in dev->irq that IPSEC irq is 3 + 2
- do a set_irq 0->3 on PCI host
But now IPSEC irq is not routed anymore to the mips code and dev->irq is
wrong. This causes a problem described in [1].
This patch tries to solve the problem by making set_irq configure the
device we want to take the irq on the shared irq0. The previous example
becomes:
- store in dev->irq that IPSEC irq is 3 + 2
- do a set_irq 0->3 on PCI host:
- irq 3 is already taken by IPSEC. do a set_irq 3->0 on IPSEC
I also added some code to print the irq configuration after irq setup to
allow easier debugging. And I add extra checking in ssb_mips_irq to report
device without irq or device with not routed irq.
[1] http://www.danm.de/files/src/bcm5365p/REPORTED_DEVICES
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by : Michael Buesch <mb@bu3sch.de>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
this patch export ssb_watchdog_timer_set to allow to use it in a Linux
watchdog driver.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by : Michael Buesch <mb@bu3sch.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds SSB functionality to register a fallback SPROM image from the
architecture setup code.
Weird architectures exist that have half-assed SSB devices without SPROM attached to
their PCI busses. The architecture can register a fallback SPROM image that is
used if no SPROM is found on the SSB device.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for the SSB PMU.
A PMU is found on Low-Power devices.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds detection code for the LP-PHY and SPROM
extraction code for version 8, which is needed by the LP-PHY and
newer N-PHY.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used on my macbook. N PHY, obviously nothing works
yet, but we can detect the chip with this patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
We want to submit a patch to -next, which will remove bus_id from
"struct device", to find the remaining pieces to convert, and finally
switch over to the new api, which will remove the 20 bytes array
and does no longer have a size limitation.
CC: Michael Buesch <mb@bu3sch.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the target system cannot support SSB, then don't show the menu option as
it'll simply be an empty submenu.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SSB_BUSTYPE_SSB type devices, we need to initialize dma_mask using
coherent_dma_mask so that calls to dma_set_mask() succeed.
It fixes the regression on the b44 driver introduced by commit
f225763a7d
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Only rev 1 and 2 ssb SPROMs have fields named et0mac and et1mac;
however, all of the extraction routines extract pseudo data for these
fields from regions that are all 1's resulting in a hardware address
of FF:FF:FF:FF:FF:FF. This patch forces such a fill at the beginning of
the data extraction process, and only does the formal extraction if the
SPROM rev is 1 or 2.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although a revision 5 SPROM has not been seen in the wild, the
open-source portion of the MIPS driver 4.150.10.5 describes its
layout, which is mostly inherited from revision 4. This patch
implements the differences.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CS_NO_MORE_ITEMS is returned by the CIS tuple reading and parsing code if
the end of a tuple chain is reached. As at least one PCMCIA driver relies
on matching this return value, replace it with -ENOSPC which is now
uniquely used for this purpose within the in-kernel pcmcia subsystem.
CC: Russell King <rmk+kernel@arm.linux.org.uk>
CC: linux-serial@vger.kernel.org
CC: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Instead of using own error or success codes, the PCMCIA code should rely on
the generic return values. Therefore, replace all occurrences of CS_SUCCESS
with 0.
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Makes ssb work on system without a PCI bus.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On embedded devices we must not route the interrupts through
the PCI core, if our host-bus is not PCI.
Reported-by: Steve Brown <sbrown@cortland.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a rewrite of the DMA API for SSB devices.
This is needed, because the old (non-existing) "API" made too many bad
assumptions on the API of the host-bus (PCI).
This introduces an almost complete SSB-DMA-API that maps to the lowlevel
bus-API based on the bustype.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes setting the coherent DMA mask for PCI devices.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current code checks for the special signature that signifies
a revision 4 SPROM. Now that a rev. 8 SPROM with a 440-byte length
has been found that may not have any special code, this check could
be relaxed. With this patch, if the CRC is incorrect for a 256-byte
SPROM, the code will immediately check for a 440-byte SPROM. If there
is still a CRC error, the size is set to 440 bytes, which allows dumping
of most of any 512-byte SPROM if one is encountered.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the SSB SPROM a field set to all ones means the value
is not defined in the SPROM.
In case of the boardflags, we need to set them to zero
to avoid confusing drivers. Drivers will only check the
flags by ANDing.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Gabor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we fixed the TPS flag assignment in commit
b63009b456
we don't need the workaround for the bcm44xx chip anymore.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes DMA on architectures where DMA is nontrivial, like PPC64.
We must use the host-device's (PCI) struct device for any DMA
operation instead of the SSB device. For this we add a new
struct device pointer to the SSB device structure that will always
point to the right device for DMAing.
Without this patch b43 and b44 drivers won't work on complex-DMA
architectures, that for example need dev->archdata for DMA operations.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
