Fix recently introduced I2C build breakage on AP325RXA and Migo-R.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This flattens out the board directories in to individual mach groups,
we will use this for getting rid of unneeded directories, simplifying
the build system, and becoming more coherent with the refactored
arch/sh/include topology.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When I compiled Solution Engine, this become compile error
because plaform device of sh_eth device becomes enable.
When sh7710/sh7712 which could use sh_eth was chosen,
revised it so that platform device of sh_eth device became enable.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up the workaround in 2b4b2bb421
and cleans up __put_user_asm() to get the sizing right from the onset.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Oops, machvec.h is in asm/, it was previously removed due to overzealous
trimming. Fix up the path again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the sparc changes a439fe51a1.
Most of the moving about was done with Sam's directions at:
http://marc.info/?l=linux-sh&m=121724823706062&w=2
with subsequent hacking and fixups entirely my fault.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add AP325RXA specific platform data for on-chip sh7723 CEU and ncm03j camera.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pass board specific smc911x parameters using struct smc911x_platdata.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add Migo-R specific platform data for on-chip sh7722 CEU and ov772x camera.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
fix the problem that cannot boot using uImage when PAGE_SIZE is
8kbyte or 64kbyte.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Without this patch, signals sent during architecture specific signal
handling (typically as a result of the user's stack being inaccessible)
are ignored.
This is the SH version of commit c3ff8ec31c
which was for the i386.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7343 processor and in the board code
for Solution Engine 7343. Remove duplicate MSTPCR register definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7722 processor and in the board code
for Migo-R and Solution Engine 7722. Remove duplicate MSTPCR register
definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7723 processor and in the ap325rxa
board code. Remove duplicate MSTPCR register definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Show all clocks in /proc/clocks, and also show if they are enabled or
disabled. This is useful to show MSTPCR bits on SuperH Mobile processors.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code makes sh7343 share the sh7722 clock code. Instead of just using
the good and very old sh7343 clock implmentation, switch to the new MSTPCR
enabled clock code. SIU clocks are disabled on sh7343 for now.
With this change all SuperH Mobile devices now use the same clock code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Handle module stop clock bits in MSTPCRn through the clock framework.
The clocks are named after the bits in the data sheet. The association
between bit number and hardware block is processor specific.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 1ea0704e0d
(mm: add a ptep_modify_prot transaction abstraction)
triggered on sh build errors like the following:
<-- snip -->
...
CC arch/sh/mm/pg-sh4.o
cc1: warnings being treated as errors
include2/asm/pgtable.h:139: error: 'ptep_get_and_clear' declared inline after being called
include2/asm/pgtable.h:139: error: previous declaration of 'ptep_get_and_clear' was here
make[2]: *** [arch/sh/mm/pg-sh4.o] Error 1
<-- snip -->
Since there's no good reason for marking these global functions as
"inline" this patch therefore removes the inline's.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds initial support for the Renesas R0P7785LC0011RL board.
This patch supports 29bit address mode only.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds physically contiguous memory chunks to the UIO devices.
The same strategy can be used in the future for the CEU as well.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the VPU, VEU(1) and VEU(2) blocks of the sh7366
to user space using the uio_pdrv_genirq platform driver.
While at it, fix up the VEU(2) interrupt vector.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the VPU, VEU2H0 and VEU2H1 blocks of the sh7723
to user space using the uio_pdrv_genirq platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the VPU and VEU blocks of the sh7722 to user space
using the uio_pdrv_genirq platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the VPU and VEU blocks of the sh7343 to user space
using the uio_pdrv_genirq platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is
By sh2
- Remove duplicate code
- Reduce stack usage
- Cleanup and little optimize
By sh2a
- Add missing handler(256 to 511)
- Use sh2a instructions handler
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
updated the following codes for Solution Endine 7343:
- fix compile error in arch/sh/boards/se/7343/irq.c
- add nor flash physmaps
- update defconfig
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove inline from ptep_get_and_clean() to match with header file prototype.
Makes linux-next build.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables I2C on the sh7723-based ap325rxa board.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds platform data for the single I2C channel on sh7366.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds platform data for the single I2C channel on sh7723.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds platform data for two I2C channels to the sh7343.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is based on interrupt acknowledge code for external
interrupt sources on sh3 processors and adds on sh4a processors.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The current kernel behaviour is to reenable interrupts unconditionally
when taking a page fault. This patch changes this to only enable them
if interrupts were previously enabled.
It also fixes a problem seen with this fix in place: the kernel previously
flushed the vsyscall page when handling a signal, which is not only
unncessary, but caused a possible sleep with interrupts disabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add implementation of flush_icache_range() suitable for signal handler
and kprobes. Remove flush_cache_sigtramp() and change signal.c to use
flush_icache_range().
Signed-off-by: Chris Smith <chris.smith@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
