These are presently only defined for sh32, use the plain unoptimized
versions for sh64. Fixes up smsc911x build.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this is special-cased for early initialization. While there are
situations where these static early initializations are still necessary,
with minor changes it is possible to use this for the regular ioremap
implementation as well. This allows us to kill off the special-casing for
the remap completely and to start tidying up all of the SH-5
special-casing in drivers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All 32-bit SuperH processors currently go through __ioremap_mode()
and check for IO_TRAPPED and directly mapped segments. With this
patch we simplify the MMU less case with a pass through version of
__ioremap_mode() which just returns the physical address.
The effects of this is change are:
- fix non-MMU ioremap() of high address hardware blocks (sh7203 CMT)
- make sure IO_TRAPPED is not selected
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a method for supporting fixed PMB mappings inherited from
the bootloader, as an alternative to the dynamic PMB mapping currently
used by the kernel. In the future these methods will be combined.
P1/P2 area is handled like a regular 29-bit physical address, and local
bus device are assigned P3 area addresses.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a pass-through case when ioremapping P4 addresses.
Addresses passed to ioremap() should be physical addresses, so the
best option is usually to convert the virtual address to a physical
address before calling ioremap. This will give you a virtual address
in P2 which matches the physical address and this works well for
most internal hardware blocks on the SuperH architecture.
However, some hardware blocks must be accessed through P4. Converting
the P4 address to a physical and then back to a P2 does not work. One
example of this is the sh7722 TMU block, it must be accessed through P4.
Without this patch P4 addresses will be mapped using PTEs which
requires the page allocator to be up and running.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the PMB enabled, only P1SEG and up are covered by the PMB mappings,
meaning that situations where out-of-bounds physical addresses are read
from will lead to TLB reset after the PMB miss, allowing for use cases
like dd if=/dev/mem to reset the TLB.
Fix this up to make sure the reference is between __MEMORY_START (phys)
and __pa(high_memory). This is coherent across all variants of sh/sh64
with and without MMU, though the PMB bug itself is only applicable to
SH-4A parts.
Reported-by: Hideo Saito <saito@densan.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This tidies up a lot of the PIO/MMIO split. No in-tree platforms were
making use of the MMIO overloading through the machvec (nor have any of
them been in some time), so we just kill all of that off. The ISA I/O
routine wrapping remains unaffected, which remains the only special
casing outside of the iomap API that boards need to think about.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These were doing largely bogus things and using the wrong typing for
the address. Bring these in line with the ARM definitions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the sparc changes a439fe51a1.
Most of the moving about was done with Sam's directions at:
http://marc.info/?l=linux-sh&m=121724823706062&w=2
with subsequent hacking and fixups entirely my fault.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
