Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset rx chain before trying to drain it.
Shut interrupts off last, incase there's something to report.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit changes to shutdown path broke startup on some systems.
revert commit c0bad0f2e4
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sky2 driver on PowerPC targets floods kernel log with following errors:
eth1: hw csum failure.
Call Trace:
[ef84b8a0] [c00075e4] show_stack+0x50/0x160 (unreliable)
[ef84b8d0] [c02fa178] netdev_rx_csum_fault+0x3c/0x5c
[ef84b8f0] [c02f6920] __skb_checksum_complete_head+0x7c/0x84
[ef84b900] [c02f693c] __skb_checksum_complete+0x14/0x24
[ef84b910] [c0337e08] tcp_v4_rcv+0x4c8/0x6f8
[ef84b940] [c031a9c8] ip_local_deliver+0x98/0x210
[ef84b960] [c031a788] ip_rcv+0x38c/0x534
[ef84b990] [c0300338] netif_receive_skb+0x260/0x36c
[ef84b9c0] [c025de00] sky2_poll+0x5dc/0xcf8
[ef84ba20] [c02fb7fc] net_rx_action+0xc0/0x144
The NIC is Yukon-2 EC chip revision 1.
Converting checksum field from le16 to CPU byte order fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements skb recycling. It reclaims transmitted skb's
for use in the receive ring.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the size of the driver transmit ring to reduce latency
and allow qdisc to do better rate control. Also make it
obvious what the minimum transmit ring allowed is and why.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it is likely that there are multiple packets received per
interrupt, only update the receive counters once after all
packets are processed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic in sky2_down was incorrect. Receiver could report status
after rx_stop was called.
The steps need to be:
* stop new frames from being transmitted
* shut off transmit/receive logic
* synchronize with NAPI to process status info about transmitter
and receiver
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some read's to avoid any PCI posting issues when controlling
irq's.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset more parts of the receive path when device is take offline.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This unblocks the chip if it is stuck in pause cycle during
shutdown.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to compute VPD size didn't handle some systems that use
chip without VPD. Also some of the newer chips use some additional
registers to store the actual size, and wasn't worth putting the
additional complexity in, so just remove the code.
No big loss since the code to set the VPD size was only a
convenience so that utilities would not read the extra space past
the end of the available VPD.
Move the first PCI config read earlier to detect bad hardware
where it returns all ones and refuse loading driver before furthur
damage.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Read configuration register during probe and use it to size the
available VPD. Move existing code using same register slightly
earlier in probe handling.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VPD stuff has more data and isn't generally that useful, so move
it into the existing debugfs display and use the new PCI VPD
accessor routines.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On non-x86 platforms it is possible to run out of DMA mapping resources.
The driver was ignoring this and could cause corruptions.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workaround is not needed. It was inherited from sk98lin driver but only
applies to an early development version of the chip that is not supported
by sky2. The workaround required an unnecessary pci read which hurts performance
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Printing anything over netconsole before hw is up and running is,
of course, not going to work.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to new network device ops interface. Slight additional complexity
here because the second port does not allow netpoll and therefore has
different virtual function table.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
sky2_set_wol().
Remove an open-coded reference to the standard PCI PM registers that
is not used any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change bootup messages to print more information. This is to help users
who may have old buggy EEPROM image.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cleanup and harden the routines accessing the EEPROM.
1. Prevent spin forever waiting for the TWSI bus
2. Fix write eeprom to write full words rather than only 16 bits
Luckly the vendor doesn't provide EEPROM in Linux format so it must never
have been used.
3. Don't allow partial eeprom writes, not needed, not safe.
These are non-urgent bug fixes.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On my test box with the Asus M3A32-MVP main board there is a
regression from 2.6.26 related to suspend, hibernation and
shutdown. Namely, if Wake-on-LAN is enabled with
'ethtool -s eth0 wol g', the box hangs solid during all of these
operations, while executing either sky2_suspend(), or
sky2_shutdown(). This patch fixes it for me.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/net/acenic.c
drivers/net/bnx2x_link.c
drivers/net/bnx2x_main.c
drivers/net/cpmac.c
drivers/net/gianfar_sysfs.c
drivers/net/ipg.h
drivers/net/ppp_mppe.c
drivers/net/pppol2tp.c
drivers/net/r6040.c
drivers/net/sh_eth.c
drivers/net/sky2.c
drivers/net/tehuti.h
drivers/net/typhoon.c
This patch removes the said #include <linux/version.h>.
Signed-off-by: Huang Weiyi <hwy@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the problems reported for 2.6.27-rc1 caused by over aggressive
power management. Turning clock off on PCI Express is problematic for WOL,
and when doing multi-booting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It is unnecessary, to stop queue and turn off carrier in shutdown
routine. With new netdev_queue this causes warnings.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Yukon 2 Ultra 2 chip set (88E8057) based on code in latest
version of vendor driver (sk98lin 10.60.2.3). Untested on real hardware.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PCI device table can be marked as devinitconst by using macro.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change how chip version is printed so that if an unknown version is detected
nothing breaks.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change the setup of the PHY registers on some chip ids. These changes
make the latest sky2 driver follow the vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Turn on special bits to save more power when device is shutdown.
Tested on a limited range of hardware, some of the bits are for hardware
that probably isn't even in production (like Yukon Supreme) and was ported
from the vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Put PHY int sleep mode (from vendor sk98lin 10.50 driver) when the
network device is brought down.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Later changes add more code to PHY power changes so refactor now.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
If device has to be reset by sky2_restart, then need to restore
the VLAN acceleration settings.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Any usage of sky2 on new Yukon Supreme would cause a NULL dereference.
The chip is very new, so the support is still untested; vendor has
not sent any eval hardware.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There are a couple of possible races on suspend/resume.
First the driver needs to block new packets from being queued for Tx.
The other less likely problem is the watchdog timer going off
during resume.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix problems in LED management, so ethtool -p works correctly on Yukon-EC
and other chips. The driver was incorrectly setting the PHY LED overide bits.
Moral: read the spec sheet, not the vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
