All audio related omap_hwmod_ocp_if *_dma can be removed from the data since
we can just add the user flag to the non dma structure.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The spinlock module's SYSCONFIG register does not support
smart wakeup, so remove this flag from the idle modes in
the spinlock hwmod definition.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without this, the USB devices are sometimes not detected on OMAP4 Panda
with u-boot v2013.10.
Unlike what the comment states, errata i660 does not state that we
can't RESET the USB host module. Instead it states that RESET is the
only way to recover from a deadlock situation.
RESET ensures that the module is in a known good state irrespective
of what bootloader does with the module, so it must be done at boot.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> # Panda, BeagleXM
Acked-by: Benoît Cousson <bcousson@baylibre.com>
Fixes: af88fa9aa7 ("ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4")
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For modules/IPs/hwmods which do not have
-1- sys->class->reset()
and
-2- hardreset lines
and
-3- No way to do an ocp reset (no sysc control)
the flag 'HWMOD_INIT_NO_RESET' is not much useful.
Cleanup all such instances across various hwmod data files.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
With commit '82702ea11ddfe0e43382e1fa5b66d807d8114916' "ARM: OMAP2+:
Fix serial init for device tree based booting" stubbing out
omap_serial_early_init() for Device tree based booting, there was a
crash observed on AM335x based devices when hwmod does a
_setup_reset() early at boot.
This was rootcaused to hwmod trying to reset console uart while
earlycon was using it. The way to tell hwmod not to do this is to
specify the HWMOD_INIT_NO_RESET flag, which were infact set by the
omap_serial_early_init() function by parsing the cmdline to identify
the console device.
Parsing the cmdline to identify the uart used by earlycon itself seems
broken as there is nothing preventing earlycon to use a different one.
This patch, instead, attempts to populate the requiste flags for hwmod
based on the CONFIG_DEBUG_OMAPxUARTy FLAGS. This gets rid of the need
for cmdline parsing in the DT as well as non-DT cases to identify the
uart used by earlycon.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reported-by: Mark Jackson <mpfj-list@newflow.co.uk>
Reported-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit '3b9b10151c6838af52244cec4af41a938bb5b7ec' cleaned up the
data file to remove all irq and dma entries for all hwmods, which
are now populated by DT. But mcspi and mmc irq, dma entries were
retained since MMC, NFS boot was not working. Since it is root caused
to be an issue with only DMA entries [1], irq can be safely removed.
[1] http://www.mail-archive.com/linux-omap@vger.kernel.org/msg90115.html
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 3b9b10151c (ARM: OMAP4: hwmod data:
Clean up the data file) removes hwmod data for omap4, including DSS
data. DSS has not yet been converted to DT, so the hwmod data is still
needed.
This patch adds back the DSS parts of the hwmod data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- The IO resource information like dma request lines, irq number and
ocp address space can be populated via dt blob. So such data is stripped
from OMAP4 SOC hwmod data file.
- The devices which are still missing the device tree bindings,
address space entries are not removed yet. When such devices add
the dt bindings, respective address space data can be deleted.
- Also other unnecessary hwmods like firewalls are removed as a part of this.
Since emif was getting registered only because of this firewalls links,
the mpu->emif direct link is added now.
The above update, results in reduction of about ~1650 lines of code.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@linaro.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated for omap44xx_usb_phy_and_pll_addrs, dropped
mcspi and mmc changes to avoid regressions on omap4sdp]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is omap4+ only and no longer needed as omap4+ can be booted
using device tree.
Also remove the related pdata handling from the driver and the
now unneeded platform_data/omap_ocp2scp.h.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP UART IP needs software control for slave idle modes based on functional
state of the IP. i.e The IP slave idle settings should be set to 'noidle' when
being used and then put back to 'smart_idle' when unused. Currently this is
handled by the driver with function pointers implemented in platform code.
This however breaks in case of device tree because of missing idle handling
APIs.
Previous patches in this series added a flag HWMOD_SWSUP_SIDLE_ACTIVE which
takes care of the mentioned requirement. Hence add the flag for all UART IPs
to take advantage of feature supported by framework.
Subsequent patches removes the slave idle handling from driver code.
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org> # OMAP4/Panda
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 92702df357 ("ARM: OMAP4: PM: fix PM regression introduced by recent
clock cleanup") makes the 'ocp2scp_usb_phy_phy_48m' as optional
functional clock causing regression in MUSB. But this 48MHz clock is a
mandatory clock for usb phy attached to ocp2scp and hence made as the main
clock for ocp2scp.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[paul@pwsan.com: add comment to the hwmod data to try to prevent any
future mistakes here]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 17b7e7d335 ("ARM: OMAP4:
clock/hwmod data: start to remove some IP block control "clocks"")
introduced a regression preventing the L3INIT clockdomain of OMAP4
systems from entering idle. This in turn prevented these systems from
entering full chip clock-stop.
The regression was caused by the incorrect removal of a so-called
"optional functional clock" from the OMAP4 clock data. This wasn't
caught for two reasons. First, I missed the retention entry failure
in the branch test logs:
http://www.pwsan.com/omap/testlogs/cleanup_a_3.9/20130126014242/pm/4460pandaes/4460pandaes_log.txt
Second, the integration data for the OCP2SCP PHY IP block, added by
commit 0c6688753f ("ARM: OMAP4: hwmod
data: add remaining USB-related IP blocks"), should have associated this
clock with the IP block, but did not.
Fix by adding back the so-called "optional" functional clock to the
clock data, and by linking that clock to the OCP2SCP PHY IP block
integration hwmod data.
The problem patch was discovered by J, Keerthy <j-keerthy@ti.com>.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This branch contains changes for OMAP that came in late during the release
staging, close to when the merge window opened.
It contains, among other things:
- OMAP PM fixes and some patches for audio device integration
- OMAP clock fixes related to common clock conversion
- A set of patches cleaning up WFI entry and blocking.
- A set of fixes and IP block support for PM on TI AM33xx SoCs (Beaglebone, etc)
- A set of smaller fixes and cleanups around AM33xx restart and revision
detection, as well as removal of some dead code (CONFIG_32K_TIMER_HZ)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=/vBT
-----END PGP SIGNATURE-----
Merge tag 'late-omap' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late OMAP changes from Olof Johansson:
"This branch contains changes for OMAP that came in late during the
release staging, close to when the merge window opened.
It contains, among other things:
- OMAP PM fixes and some patches for audio device integration
- OMAP clock fixes related to common clock conversion
- A set of patches cleaning up WFI entry and blocking.
- A set of fixes and IP block support for PM on TI AM33xx SoCs
(Beaglebone, etc)
- A set of smaller fixes and cleanups around AM33xx restart and
revision detection, as well as removal of some dead code
(CONFIG_32K_TIMER_HZ)"
* tag 'late-omap' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: omap2: include linux/errno.h in hwmod_reset
ARM: OMAP2+: fix some omap_device_build() calls that aren't compiled by default
ARM: OMAP4: hwmod data: Enable AESS hwmod device
ARM: OMAP4: hwmod data: Update AESS data with memory bank area
ARM: OMAP4+: AESS: enable internal auto-gating during initial setup
ASoC: TI AESS: add autogating-enable function, callable from architecture code
ARM: OMAP2+: hwmod: add enable_preprogram hook
ARM: OMAP4: clock data: Add missing clkdm association for dpll_usb
ARM: OMAP2+: PM: Fix the dt return condition in pm_late_init()
ARM: OMAP2: am33xx-hwmod: Fix "register offset NULL check" bug
ARM: OMAP2+: AM33xx: hwmod: add missing HWMOD_NO_IDLEST flags
ARM: OMAP: AM33xx hwmod: Add parent-child relationship for PWM subsystem
ARM: OMAP: AM33xx hwmod: Corrects PWM subsystem HWMOD entries
ARM: DTS: AM33XX: Add nodes for OCMC RAM and WKUP-M3
ARM: OMAP2+: AM33XX: Update the hardreset API
ARM: OMAP2+: AM33XX: hwmod: Update the WKUP-M3 hwmod with reset status bit
ARM: OMAP2+: AM33XX: hwmod: Fixup cpgmac0 hwmod entry
ARM: OMAP2+: AM33XX: hwmod: Update TPTC0 hwmod with the right flags
ARM: OMAP2+: AM33XX: hwmod: Register OCMC RAM hwmod
ARM: OMAP2+: AM33XX: CM/PRM: Use __ASSEMBLER__ macros in header files
...
This is a larger set of new functionality for the existing SoC families,
including:
* vt8500 gains support for new CPU cores, notably the Cortex-A9 based wm8850
* prima2 gains support for the "marco" SoC family, its SMP based cousin
* tegra gains support for the new Tegra4 (Tegra114) family
* socfpga now supports a newer version of the hardware including SMP
* i.mx31 and bcm2835 are now using DT probing for their clocks
* lots of updates for sh-mobile
* OMAP updates for clocks, power management and USB
* i.mx6q and tegra now support cpuidle
* kirkwood now supports PCIe hot plugging
* tegra clock support is updated
* tegra USB PHY probing gets implemented diffently
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PRrg
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC-specific updates from Arnd Bergmann:
"This is a larger set of new functionality for the existing SoC
families, including:
- vt8500 gains support for new CPU cores, notably the Cortex-A9 based
wm8850
- prima2 gains support for the "marco" SoC family, its SMP based
cousin
- tegra gains support for the new Tegra4 (Tegra114) family
- socfpga now supports a newer version of the hardware including SMP
- i.mx31 and bcm2835 are now using DT probing for their clocks
- lots of updates for sh-mobile
- OMAP updates for clocks, power management and USB
- i.mx6q and tegra now support cpuidle
- kirkwood now supports PCIe hot plugging
- tegra clock support is updated
- tegra USB PHY probing gets implemented diffently"
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
ARM: prima2: remove duplicate v7_invalidate_l1
ARM: shmobile: r8a7779: Correct TMU clock support again
ARM: prima2: fix __init section for cpu hotplug
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
ARM: tegra: sort Kconfig selects for Tegra114
ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
ARM: tegra: Fix build error for gic update
ARM: tegra: remove empty tegra_smp_init_cpus()
ARM: shmobile: Register ARM architected timer
ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
ARM: shmobile: r8a7779: Correct TMU clock support
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
...
Some OMAP4 power management fixes and audio device integration
patches. This pull request contains a fix for an issue discovered during
branch integration.
Basic test logs are available at:
http://www.pwsan.com/omap/testlogs/omap4_prcm_devel_a_3.9/20130210112717/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Qbkt
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.9/pm-omap4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into late/omap
From Tony Lindgren:
omap4 pm changes via Paul Walmsley <paul@pwsan.com>:
Some OMAP4 power management fixes and audio device integration
patches. This pull request contains a fix for an issue discovered during
branch integration.
Basic test logs are available at:
http://www.pwsan.com/omap/testlogs/omap4_prcm_devel_a_3.9/20130210112717/
* tag 'omap-for-v3.9/pm-omap4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: hwmod data: Enable AESS hwmod device
ARM: OMAP4: hwmod data: Update AESS data with memory bank area
ARM: OMAP4+: AESS: enable internal auto-gating during initial setup
ASoC: TI AESS: add autogating-enable function, callable from architecture code
ARM: OMAP2+: hwmod: add enable_preprogram hook
ARM: OMAP2+: PM: Fix the dt return condition in pm_late_init()
ARM: OMAP4: PM: Warn users about usage of older bootloaders
Enable AESS data in hwmod in order to be able to probe
audio driver.
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add AESS memory bank data in hwmod in order to provide memory address
information to the driver.
This version also changes the AESS main clock to use a
non-CLKCTRL-based functional clock. These are being removed from the
clock data, since they should be handled by the IP block integration
code. Without this change, the kernel crashes during boot. Thanks to
Tony Lindgren for reporting this during a test merge.
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
[paul@pwsan.com: updated to change the AESS main_clk]
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Enable the AESS auto-gating control bit during AESS hwmod setup. This
fixes the following boot warning on OMAP4:
omap_hwmod: aess: _wait_target_disable failed
Without this patch, the AESS IP block does not indicate to the PRCM
that it is idle after it is reset. This prevents some types of SoC
power management until something sets the auto-gating control bit.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Péter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Now that we have a separate driver for the control module,
stop populating the control module device data in other modules
(PHY and OTG) device info.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert all DEFINE_OMAP_MUX_GATE() combinations that list MODULEMODE
registers in their gate arguments to DEFINE_OMAP_MUX(), dropping the
MODULEMODE data. This is possible because the MODULEMODE bits control
IP blocks, not clocks; and the hwmod code takes care of IP block
control. Rename these clocks to reflect the original multiplexer name
as specified in the comments. And convert the hwmod data to use the
multiplexer clock name.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Mike Turquette <mturquette@linaro.org>
Remove some leaf "clocks" that are actually IP block idle control
points, since these should now be handled by the hwmod code.
There are still a few types of MODULEMODE clocks that need to be
cleaned up:
- those still in use by driver or integration code
- those in DEFINE_CLK_OMAP_MUX_GATE() blocks; the gate portion of
these should be removed
A similar process may also be possible on OMAP2/3.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Mike Turquette <mturquette@linaro.org>
McPDM need to be configured to NO_IDLE mode when it is in used otherwise
vital clocks will be gated which results 'slow motion' audio playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[paul@pwsan.com: copy patch description into hwmod data comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
From Tony Lindgren:
Here are few more patches to finish the omap changes for
multiplatform conversion that are not strictly fixes, but
were too complex to do with the dependencies during the
merge window. Those are to move of serial-omap.h to
platform_data, and the removal of remaining cpu_is_omap
macro usage outside mach-omap2.
Then there are several trivial fixes for typos and few
minimal omap2plus_defconfig updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RE6Z
-----END PGP SIGNATURE-----
Merge tag 'omap-late-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM cleanups for omap from Olof Johansson:
"From Tony Lindgren:
Here are few more patches to finish the omap changes for multiplatform
conversion that are not strictly fixes, but were too complex to do
with the dependencies during the merge window. Those are to move of
serial-omap.h to platform_data, and the removal of remaining
cpu_is_omap macro usage outside mach-omap2.
Then there are several trivial fixes for typos and few minimal
omap2plus_defconfig updates."
* tag 'omap-late-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arch/arm/mach-omap2/dpll3xxx.c: drop if around WARN_ON
OMAP2: Fix a typo - replace regist with register.
ARM/omap: use module_platform_driver macro
ARM: OMAP2+: PMU: Remove unused header
ARM: OMAP4: remove duplicated include from omap_hwmod_44xx_data.c
ARM: OMAP2+: omap2plus_defconfig: enable twl4030 SoC audio
ARM: OMAP2+: omap2plus_defconfig: Add tps65217 support
ARM: OMAP2+: enable devtmpfs and devtmpfs automount
ARM: OMAP2+: omap_twl: Change TWL4030_MODULE_PM_RECEIVER to TWL_MODULE_PM_RECEIVER
ARM: OMAP2+: Drop plat/cpu.h for omap2plus
ARM: OMAP: Split fb.c to remove last remaining cpu_is_omap usage
MAINTAINERS: Add an entry for omap related .dts files
A few new features this merge-window. The most important one is
probably, that dma-debug now warns if a dma-handle is not checked with
dma_mapping_error by the device driver. This requires minor changes to
some architectures which make use of dma-debug. Most of these changes
have the respective Acks by the Arch-Maintainers.
Besides that there are updates to the AMD IOMMU driver for refactor the
IOMMU-Groups support and to make sure it does not trigger a hardware
erratum.
The OMAP changes (for which I pulled in a branch from Tony Lindgren's
tree) have a conflict in linux-next with the arm-soc tree. The conflict
is in the file arch/arm/mach-omap2/clock44xx_data.c which is deleted in
the arm-soc tree. It is safe to delete the file too so solve the
conflict. Similar changes are done in the arm-soc tree in the common
clock framework migration. A missing hunk from the patch in the IOMMU
tree will be submitted as a seperate patch when the merge-window is
closed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pPHZ
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"A few new features this merge-window. The most important one is
probably, that dma-debug now warns if a dma-handle is not checked with
dma_mapping_error by the device driver. This requires minor changes
to some architectures which make use of dma-debug. Most of these
changes have the respective Acks by the Arch-Maintainers.
Besides that there are updates to the AMD IOMMU driver for refactor
the IOMMU-Groups support and to make sure it does not trigger a
hardware erratum.
The OMAP changes (for which I pulled in a branch from Tony Lindgren's
tree) have a conflict in linux-next with the arm-soc tree. The
conflict is in the file arch/arm/mach-omap2/clock44xx_data.c which is
deleted in the arm-soc tree. It is safe to delete the file too so
solve the conflict. Similar changes are done in the arm-soc tree in
the common clock framework migration. A missing hunk from the patch
in the IOMMU tree will be submitted as a seperate patch when the
merge-window is closed."
* tag 'iommu-updates-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (29 commits)
ARM: dma-mapping: support debug_dma_mapping_error
ARM: OMAP4: hwmod data: ipu and dsp to use parent clocks instead of leaf clocks
iommu/omap: Adapt to runtime pm
iommu/omap: Migrate to hwmod framework
iommu/omap: Keep mmu enabled when requested
iommu/omap: Remove redundant clock handling on ISR
iommu/amd: Remove obsolete comment
iommu/amd: Don't use 512GB pages
iommu/tegra: smmu: Move bus_set_iommu after probe for multi arch
iommu/tegra: gart: Move bus_set_iommu after probe for multi arch
iommu/tegra: smmu: Remove unnecessary PTC/TLB flush all
tile: dma_debug: add debug_dma_mapping_error support
sh: dma_debug: add debug_dma_mapping_error support
powerpc: dma_debug: add debug_dma_mapping_error support
mips: dma_debug: add debug_dma_mapping_error support
microblaze: dma-mapping: support debug_dma_mapping_error
ia64: dma_debug: add debug_dma_mapping_error support
c6x: dma_debug: add debug_dma_mapping_error support
ARM64: dma_debug: add debug_dma_mapping_error support
intel-iommu: Prevent devices with RMRRs from being placed into SI Domain
...
Pull i2c-embedded changes from Wolfram Sang:
- CBUS driver (an I2C variant)
- continued rework of the omap driver
- s3c2410 gets lots of fixes and gains pinctrl support
- at91 gains DMA support
- the GPIO muxer gains devicetree probing
- typical fixes and additions all over
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (45 commits)
i2c: omap: Remove the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE flag
i2c: at91: add dma support
i2c: at91: change struct members indentation
i2c: at91: fix compilation warning
i2c: mxs: Do not disable the I2C SMBus quick mode
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Remove recently introduced performance overheads
i2c: ocores: Move grlib set/get functions into #ifdef CONFIG_OF block
i2c: s3c2410: Add fix for i2c suspend/resume
i2c: s3c2410: Fix code to free gpios
i2c: i2c-cbus-gpio: introduce driver
i2c: ocores: Add support for the GRLIB port of the controller and use function pointers for getreg and setreg functions
i2c: ocores: Add irq support for sparc
i2c: omap: Move the remove constraint
ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
i2c: s3c2410: do not special case HDMIPHY stuck bus detection
i2c: s3c2410: use exponential back off while polling for bus idle
i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
i2c: s3c2410: grab adapter lock while changing i2c clock
i2c: s3c2410: Add support for pinctrl
...
This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=h2Qo
-----END PGP SIGNATURE-----
Merge tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC power management and clock changes from Olof Johansson:
"This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable."
* tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
ARM: EXYNOS: Add flush_cache_all in suspend finisher
ARM: EXYNOS: Remove scu_enable from cpuidle
ARM: EXYNOS: Fix soft reboot hang after suspend/resume
ARM: EXYNOS: Add support for rtc wakeup
ARM: EXYNOS: fix the hotplug for Cortex-A15
ARM: OMAP2+: omap_device: Correct resource handling for DT boot
ARM: OMAP2+: hwmod: Add possibility to count hwmod resources based on type
ARM: OMAP2+: hwmod: Add support for per hwmod/module context lost count
ARM: OMAP2+: PRM: initialize some PRM functions early
ARM: OMAP2+: voltage: fixup oscillator handling when CONFIG_PM=n
ARM: OMAP4: USB: power down MUSB PHY during boot
ARM: OMAP2+: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP2xxx: clock: drop obsolete clock data
ARM: OMAP2: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP3+: DPLL: drop !CONFIG_COMMON_CLK sections
ARM: AM33xx: clock: drop obsolete clock data
ARM: OMAP3xxx: clk: drop obsolete clock data
...
This prevents hwmod _enable_clocks...omap2_dflt_clk_enable path
from enabling modulemode inside CLKCTRL using its clk->enable_reg
field. Instead is left to _omap4_enable_module though soc_ops, as
the one in charge of this setting.
According to comments received[1] for related patches the idea is
to get rid of leaf clocks in future. So remove these two while at it.
[1] http://lkml.org/lkml/2012/8/20/226
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=w+UN
-----END PGP SIGNATURE-----
Merge tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm2
From Tony Lindgren:
Remaining patches to allow omap2+ to build with multiplatform
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
* tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
Conflicts due to surrounding changes in:
arch/arm/mach-omap2/omap_hwmod_2420_data.c
arch/arm/mach-omap2/omap_hwmod_2430_data.c
Signed-off-by: Olof Johansson <olof@lixom.net>
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yFcc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Move most of remaining omap iommu code to drivers/iommu.
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
* tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
Conflicts due to surrounding changes fixed up in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
drivers/media/platform/omap3isp/ispvideo.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Based on earlier discussions[1] we attempted to find a suitable
location for the omap DMA header in commit 2b6c4e73 (ARM: OMAP:
DMA: Move plat/dma.h to plat-omap/dma-omap.h) until the conversion
to dmaengine is complete.
Unfortunately that was before I was able to try to test compile
of the ARM multiplatform builds for omap2+, and the end result
was not very good.
So I'm creating yet another all over the place patch to cut the
last dependency for building omap2+ for ARM multiplatform. After
this, we have finally removed the driver dependencies to the
arch/arm code, except for few drivers that are being worked on.
The other option was to make the <plat-omap/dma-omap.h> path
to work, but we'd have to add some new header directory to for
multiplatform builds.
Or we would have to manually include arch/arm/plat-omap/include
again from arch/arm/Makefile for omap2+.
Neither of these alternatives sound appealing as they will
likely lead addition of various other headers exposed to the
drivers, which we want to avoid for the multiplatform kernels.
Since we already have a minimal include/linux/omap-dma.h,
let's just use that instead and add a note to it to not
use the custom omap DMA functions any longer where possible.
Note that converting omap DMA to dmaengine depends on
dmaengine supporting automatically incrementing the FIFO
address at the device end, and converting all the remaining
legacy drivers. So it's going to be few more merge windows.
[1] https://patchwork.kernel.org/patch/1519591/#
cc: Russell King <linux@arm.linux.org.uk>
cc: Kevin Hilman <khilman@ti.com>
cc: "Benoît Cousson" <b-cousson@ti.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Vinod Koul <vinod.koul@intel.com>
cc: Dan Williams <djbw@fb.com>
cc: Mauro Carvalho Chehab <mchehab@infradead.org>
cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
cc: David Woodhouse <dwmw2@infradead.org>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
cc: Hans Verkuil <hans.verkuil@cisco.com>
cc: Vaibhav Hiremath <hvaibhav@ti.com>
cc: Lokesh Vutla <lokeshvutla@ti.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
cc: Afzal Mohammed <afzal@ti.com>
cc: linux-crypto@vger.kernel.org
cc: linux-media@vger.kernel.org
cc: linux-mtd@lists.infradead.org
cc: linux-usb@vger.kernel.org
cc: linux-fbdev@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
and to get rid of CONFIG_OMAP_32K_TIMER and rely on the board
or devicetree provided timer configuration.
Note that these changes are on top of the recent timer fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=XZ+L
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Timer clean-up to get us closer to moving timer code to drivers,
and to get rid of CONFIG_OMAP_32K_TIMER and rely on the board
or devicetree provided timer configuration.
Note that these changes are on top of the recent timer fixes.
By Jon Hunter (32) and others
via Tony Lindgren
* tag 'omap-for-v3.8/cleanup-timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (71 commits)
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: OMAP2+: Fix compiler warning for 32k timer
ARM: OMAP: Remove unnecessary inclusion of dmtimer.h
ARM: OMAP: Add platform data header for DMTIMERs
ARM: OMAP: Remove unnecessary omap_dm_timer structure declaration
ARM: OMAP2+: Remove unnecessary local variable in timer code
ARM: OMAP: Don't store timers physical address
ARM: OMAP: Define omap_dm_timer_prepare function as static
ARM: OMAP: Clean-up dmtimer reset code
ARM: OMAP: Remove __omap_dm_timer_set_source function
ARM: OMAP: Remove unnecessary call to clk_get()
ARM: OMAP: Add dmtimer interrupt disable function
ARM: OMAP: Fix spurious interrupts when using timer match feature
ARM: OMAP: Don't restore DMTIMER interrupt status register
ARM: OMAP: Don't restore of DMTIMER TISTAT register
ARM: OMAP: Fix dmtimer reset for timer1
ARM: OMAP2+: Don't use __omap_dm_timer_reset()
ARM: OMAP2/3: Define HWMOD software reset status for DMTIMERs
ARM: OMAP3: Correct HWMOD DMTIMER SYSC register declarations
...
Change/change conflict in arch/arm/mach-omap2/board-cm-t3517.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
The OMAP_I2C_FLAG_RESET_REGS_POSTIDLE is not used anymore
in the i2c driver. Remove the flag.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQss0FAAoJEHm+PkMAQRiG6cEH/An3PYsWBBy27tzoLyVfJKF1
3m3vR8HS2tnHg6erxms+738jos59vrWXV0Ygnvw0DHbGR0HNb4rkwce/KXu/jgOD
MRYNYhlhMFJTEUFrSrcwKITrAV3kVPWXxPXgAR6Gzpr6NPKKM9TBzEv0ze56TFYz
asOxqeBcPSS7aFZlkoNsy1wG4l0Quo5ke8VZIxo9Me5qlqubAoZ6pING4wAGXqeE
tf81CevSdpe0nqr8/dlYyCvLjrurgpJQczxRCBI3mP6kLWGfUCVzZmcu86PfT9b+
35zNJwDneIoN+D9bVDHy6mrq9uQdmhWnQuhv1joTPn6RDn1nyBRBd+A5qLxSov4=
=CPoy
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc7' into next/cleanup
Merging in mainline back to next/cleanup since it has collected a few
conflicts between fixes going upstream and some of the cleanup patches.
Git doesn't auto-resolve some of them, and they're mostly noise so let's
take care of it locally.
Conflicts are in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
arch/arm/plat-omap/i2c.c
drivers/video/omap2/dss/dss.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Move iommu/iovmm headers from plat/ to platform_data/ as part of the
single zImage work.
Partially based on an earlier version by Ido Yariv <ido@wizery.com>.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently OMAP2+ devices are using the function __omap_dm_timer_reset() to
configure the clock-activity, idle, wakeup-enable and auto-idle fields in the
timer OCP_CFG register. The name of the function is mis-leading because this
function does not actually perform a reset of the timer.
For OMAP2+ devices, HWMOD is responsible for reseting and configuring the
timer OCP_CFG register. Therefore, do not use __omap_dm_timer_reset() for
OMAP2+ devices and rely on HWMOD. Furthermore, some timer instances do not
have the fields clock-activity, wakeup-enable and auto-idle and so this
function could configure the OCP_CFG register incorrectly.
Currently HWMOD is not configuring the clock-activity field in the OCP_CFG
register for timers that have this field. Commit 0f0d080 (ARM: OMAP: DMTimer:
Use posted mode) configures the clock-activity field to keep the f-clk enabled
so that the wake-up capability is enabled. Therefore, add the appropriate flags
to the timer HWMOD structures to configure this field in the same way.
For OMAP2/3 devices all dmtimers have the clock-activity field, where as for
OMAP4 devices, only dmtimer 1, 2 and 10 have the clock-activity field.
Verified on OMAP2420 H4, OMAP3430 Beagle and OMAP4430 Panda that HWMOD is
configuring the dmtimer OCP_CFG register as expected for clock-events timer.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Kevin Hilman and Paul Walmsley.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=pyxl
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.7-rc4/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren <tony@atomide.com>:
Minor OMAP PM and hwmod fixes for v3.7-rc series via
Kevin Hilman and Paul Walmsley.
* tag 'omap-for-v3.7-rc4/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: PM: fix regulator name for VDD_MPU
ARM: OMAP4: hwmod data: do not enable or reset the McPDM during kernel init
ARM: OMAP2+: hwmod: add flag to prevent hwmod code from touching IP block during init
ARM: OMAP: hwmod: wait for sysreset complete after enabling hwmod
ARM: OMAP2+: clockdomain: Fix OMAP4 ISS clk domain to support only SWSUP
ARM: OMAP2+: PM: add missing newline to VC warning message
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In order to reflect devices(usb_phy) attached to ocp2scp bus, ocp2scp
is assigned a device attribute to represent the attached devices.
This is needed to fix MUSB regression caused by commit c9e4412a
(arm: omap: phy: remove unused functions from omap-phy-internal.c)
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[tony@atomide.com: updated comments for regression info]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the prototypes in plat-omap/common.h are not
common to omap1 and omap2+, they are local to omap2+
and should not be in plat-omap/common.h.
The only shared function prototype in this file is
omap_init_clocksource_32k(), let's put that into
counter-32k.h.
Note that the new plat/counter-32k.h must not be
included from drivers, that will break omap2+ build
for CONFIG_MULTIPLATFORM.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Resolve this kernel boot message:
omap_hwmod: mcpdm: cannot be enabled for reset (3)
The McPDM on OMAP4 can only receive its functional clock from an
off-chip source. This source is not guaranteed to be present on the
board, and when present, it is controlled by I2C. This would
introduce a board dependency to the early hwmod code which it was not
designed to handle. Also, neither the driver for this off-chip clock
provider nor the I2C code is available early in boot when the hwmod
code is attempting to enable and reset IP blocks. This effectively
makes it impossible to enable and reset this device during hwmod init.
At its core, this patch is a workaround for an OMAP hardware problem.
It should be possible to configure the OMAP to provide any IP block's
functional clock from an on-chip source. (This is true for almost
every IP block on the chip. As far as I know, McPDM is the only
exception.) If the kernel cannot reset and configure IP blocks, it
cannot guarantee a sane SoC state. Relying on an optional off-chip
clock also creates a board dependency which is beyond the scope of the
early hwmod code.
This patch works around the issue by marking the McPDM hwmod record
with the HWMOD_EXT_OPT_MAIN_CLK flag. This prevents the hwmod
code from touching the device early during boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Péter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
There's no need to keep the device related things in the
common i2c.c as omap2+ is using hwmod. Split the code to
mach-omap1 and mach-omap2 parts and only leave common
code to plat-omap/i2c.c.
Note that as omap1 only has one i2c controller, we can
now remove the old device related macros.
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move plat/dma.h to plat-omap/dma-omap.h as part of single
zImage work
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to remove this from plat for ARM common zImage
support.
Also remove includes not needed by the omap_hsmmc.c driver.
Cc: linux-mmc@vger.kernel.org
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Venkatraman S <svenkatr@ti.com>
[tony@atomide.com: fold in removal of unused driver includes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This contains pretty many small commits covering fairly large range of
files in sound/ directory. Partly because of additional API support
and partly because of constantly developed ASoC and ARM stuff.
Some highlights:
- Introduced the helper function and documentation for exposing the
channel map via control API, as discussed in Plumbers; most of PCI
drivers are covered, will follow more drivers later
- Most of drivers have been replaced with the new PM callbacks (if
the bus is supported)
- HD-audio controller got the support of runtime PM and the support of
D3 clock-stop. Also changing the power_save option in sysfs kicks
off immediately to enable / disable the power-save mode.
- Another significant code change in HD-audio is the rewrite of
firmware loading code. Other than that, most of changes in HD-audio
are continued cleanups and standardization for the generic auto
parser and bug fixes (HBR, device-specific fixups), in addition to
the support of channel-map API.
- Addition of ASoC bindings for the compressed API, used by the
mid-x86 drivers.
- Lots of cleanups and API refreshes for ASoC codec drivers and
DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
- Enhancements to the ux500 and wm2000 drivers
- A new driver for DA9055 and the support for regulator bypass mode.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=uNqD
-----END PGP SIGNATURE-----
Merge tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This contains pretty many small commits covering fairly large range of
files in sound/ directory. Partly because of additional API support
and partly because of constantly developed ASoC and ARM stuff.
Some highlights:
- Introduced the helper function and documentation for exposing the
channel map via control API, as discussed in Plumbers; most of PCI
drivers are covered, will follow more drivers later
- Most of drivers have been replaced with the new PM callbacks (if
the bus is supported)
- HD-audio controller got the support of runtime PM and the support
of D3 clock-stop. Also changing the power_save option in sysfs
kicks off immediately to enable / disable the power-save mode.
- Another significant code change in HD-audio is the rewrite of
firmware loading code. Other than that, most of changes in
HD-audio are continued cleanups and standardization for the generic
auto parser and bug fixes (HBR, device-specific fixups), in
addition to the support of channel-map API.
- Addition of ASoC bindings for the compressed API, used by the
mid-x86 drivers.
- Lots of cleanups and API refreshes for ASoC codec drivers and
DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
- Enhancements to the ux500 and wm2000 drivers
- A new driver for DA9055 and the support for regulator bypass mode."
Fix up various arm soc header file reorg conflicts.
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (339 commits)
ALSA: hda - Add new codec ALC283 ALC290 support
ALSA: hda - avoid unneccesary indices on "Headphone Jack" controls
ALSA: hda - fix indices on boost volume on Conexant
ALSA: aloop - add locking to timer access
ALSA: hda - Fix hang caused by race during suspend.
sound: Remove unnecessary semicolon
ALSA: hda/realtek - Fix detection of ALC271X codec
ALSA: hda - Add inverted internal mic quirk for Lenovo IdeaPad U310
ALSA: hda - make Realtek/Sigmatel/Conexant use the generic unsol event
ALSA: hda - make a generic unsol event handler
ASoC: codecs: Add DA9055 codec driver
ASoC: eukrea-tlv320: Convert it to platform driver
ALSA: ASoC: add DT bindings for CS4271
ASoC: wm_hubs: Ensure volume updates are handled during class W startup
ASoC: wm5110: Adding missing volume update bits
ASoC: wm5110: Add OUT3R support
ASoC: wm5110: Add AEC loopback support
ASoC: wm5110: Rename EPOUT to HPOUT3
ASoC: arizona: Add more clock rates
ASoC: arizona: Add more DSP options for mixer input muxes
...
