According to the documentation, a timeout of 0 turns off timeouts,
which is not the case.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The drivers sets the hardware to idle when a timeout occurs. This can
be any reasonable value.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If timeouts or carrier range is not supported, return proper error.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We shouldn't be using ENOSYS when a feature is not available. I've tested
lirc; nothing is broken as far as I can make out.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adjust the keymap to use the correct nec scancodes, and adjust the
rc driver to output the correct nec scancodes.
Now the keymap can be used with any nec receiver, and the rc device
should work with any nec keymap.
Tested-by: Vincent McIntyre <vincent.mcintyre@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=Liea
-----END PGP SIGNATURE-----
Merge tag 'media/v4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Media regression fixes:
- serial_ir: fix a Kernel crash during boot on Kernel 4.11-rc1, due
to an IRQ code called too early
- other IR regression fixes at lirc and at the raw IR decoding
- a deadlock fix at the RC nuvoton driver
- fix another issue with DMA on stack at dw2102 driver
There's an extra patch there that change a driver interface for the
SoC VSP1 driver, with is shared between the DRM and V4L2 driver. The
patch itself is trivial, and was acked by David Arlie"
* tag 'media/v4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] v4l: vsp1: Adapt vsp1_du_setup_lif() interface to use a structure
[media] dw2102: don't do DMA on stack
[media] rc: protocol is not set on register for raw IR devices
[media] rc: raw decoder for keymap protocol is not loaded on register
[media] rc: nuvoton: fix deadlock in nvt_write_wakeup_codes
[media] lirc: fix dead lock between open and wakeup_filter
[media] serial_ir: ensure we're ready to receive interrupts
ir_raw_event_register() sets up change_protocol(), and without that set,
rc_setup_rx_device() does not set the protocol for the device on register.
The standard udev rules run ir-keytable, which writes to the protocols
file again, which hides this problem.
Fixes: 7ff2c2b ("[media] rc-main: split setup and unregister functions")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the protocol is set via the sysfs protocols attribute, the
decoder is loaded. However, when it is not when a device is first
plugged in or registered.
Fixes: acc1c3c ("[media] media: rc: load decoder modules on-demand")
Signed-off-by: Sean Young <sean@mess.org>
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the interrupt requested with devm_request_irq(), serial_ir.rcdev
is still null so will cause null deference if the irq handler is called
early on.
Also ensure that timeout_timer is setup.
Link: http://lkml.kernel.org/r/CA+55aFxsh2uF8gi5sN_guY3Z+tiLv7LpJYKBw+y8vqLzp+TsnQ@mail.gmail.com
[mchehab@s-opensource.com: moved serial_ir_probe() back to its original place]
Cc: <stable@vger.kernel.org> # 4.10
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The UK layout of the Microsoft Remote Keyboard has two missing keys:
the hash key, and the messenger key which is sent using rc6 mce.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Bail out early, otherwise we follow a null pointer.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
tx-only RC devices do not have a receive buffer.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
LIRC_SET_REC_TIMEOUT can fail if the value returned by
LIRC_GET_MIN_TIMEOUT is set due to rounding errors.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current message has some wanted spaces on it:
rc_core: Loaded IR protocol module ir-jvc-decoder, but protocol jvc still not available
Merge it into a single line.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
An RC device which is transmit-only shouldn't have the
LIRC_CAN_REC_MODE2 feature.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The GeekBox ships with a 12 button remote control which seems to use the
NEC protocol. The button keycodes were captured with the "ir-keytable"
tool (ir-keytable -p $PROTOCOL -t; human_button_pusher).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds driver for IR controller on MT7623 SoC.
and should also work on similar Mediatek SoC. Currently
testing successfully on NEC and SONY remote controller
only but it should work on others (lirc, rc-5 and rc-6).
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The staging lirc_imon driver contains 4 usb ids. Two of those have a VFD
and two don't. The VFD code is exactly the same in the mainline imon
driver, so that part is easily ported.
The staging driver produces raw IR rather than scancodes for the four
devices, so I've ported the raw IR code from staging to mainline imon.
Now that mainline imon can handle these four devices, lirc_imon is no
longer needed.
Compile tested only.
Signed-off-by: Sean Young <sean@mess.org>
Cc: Venky Raju <dev@venky.ws>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver was written using lirc since rc-core did not support
transmitter-only hardware at that time. Now that it does, port
this driver.
Compile tested only.
Signed-off-by: Sean Young <sean@mess.org>
Cc: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ir-spi is a simple device driver which supports the
connection between an IR LED and the MOSI line of an SPI device.
The driver, indeed, uses the SPI framework to stream the raw data
provided by userspace through an rc character device. The chardev
is handled by the LIRC framework and its functionality basically
provides:
- write: the driver gets a pulse/space signal and translates it
to a binary signal that will be streamed to the IR led through
the SPI framework.
- set frequency: sets the frequency whith which the data should
be sent. This is handle with ioctl with the
LIRC_SET_SEND_CARRIER flag (as per lirc documentation)
- set duty cycle: this is also handled with ioctl with the
LIRC_SET_SEND_DUTY_CYCLE flag. The driver handles duty cycles
of 50%, 60%, 70%, 75%, 80% and 90%, calculated on 16bit data.
The character device is created under /dev/lircX name, where X is
and ID assigned by the LIRC framework.
Example of usage:
fd = open("/dev/lirc0", O_RDWR);
if (fd < 0)
return -1;
val = 608000;
ret = ioctl(fd, LIRC_SET_SEND_CARRIER, &val);
if (ret < 0)
return -1;
val = 60;
ret = ioctl(fd, LIRC_SET_SEND_DUTY_CYCLE, &val);
if (ret < 0)
return -1;
n = write(fd, buffer, BUF_LEN);
if (n < 0 || n != BUF_LEN)
ret = -1;
close(fd);
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Raw IR transmitters do not need any thread listening for
occurring events. Check the driver type before running the
thread.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
IR raw transmitter driver type is specified in the enum
rc_driver_type as RC_DRIVER_IR_RAW_TX which includes all those
devices that transmit raw stream of bit to a receiver.
The data are provided by userspace applications, therefore they
don't need any input device allocation, but still they need to be
registered as raw devices.
Suggested-by: Sean Young <sean@mess.org>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move the input device allocation, map and protocol handling to
different functions.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver type can be assigned immediately when an RC device
requests to the framework to allocate the device.
This is an 'enum rc_driver_type' data type and specifies whether
the device is a raw receiver or scancode receiver. The type will
be given as parameter to the rc_allocate_device device.
Change accordingly all the drivers calling rc_allocate_device()
so that the device type is specified during the rc device
allocation. Whenever the device type is not specified, it will be
set as RC_DRIVER_SCANCODE which was the default '0' value.
Suggested-by: Sean Young <sean@mess.org>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Nuvoton-cir utilizes the encoding capabilities of rc-core to convert
scancodes from user space to pulse/space format understood by the
underlying hardware.
Converted samples are then written to the wakeup fifo along with other
necessary configuration to enable wake up functionality.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the s_wakeup_filter callback to the rc-loopback driver, which instead
of setting the filter just feeds the scancode back through the input
device so that it can be verified.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support in rc-core for drivers which implement the wakeup scancode
filter by encoding the scancode using the raw IR encoders. This is by
way of rc_dev::encode_wakeup which should be set to true and
rc_dev::allowed_wakeup_protocols should be set to the raw IR encoders.
We also do not permit the mask to be set as we cannot generate IR
which would match that.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the capability to encode Sony scancodes as raw events. Sony uses
pulse length rather than pulse distance.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the capability to encode Sharp scancodes as raw events.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the capability to encode Sanyo scancodes as raw events.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the capability to encode JVC scancodes as raw events.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the capability to encode NEC scancodes as raw events. The
scancode_to_raw is pretty much taken from the img-ir NEC filter()
callback, and modulation uses the pulse distance helper added in a
previous commit.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the capability to encode RC-6 and RC-6A scancodes as raw events.
The Manchester modulation helper is used several times with various
timings so that RC-6 header preamble, the header, header trailing bit
and the data itself can be modulated correctly.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: James Hogan <james@albanarts.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the capability to encode RC-5, RC-5X and RC-5-SZ scancodes as raw
events.
The Manchester modulation helper is used, and for RC-5X it is used twice
with two sets of timings, the first with a short trailer space for the
space in the middle, and the second with no leader so that it can
continue the space.
The encoding in RC-5-SZ first inserts a pulse and then simply utilizes
the generic Manchester encoder available in rc-core.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add IR encoding helper for pulse-distance modulation as used by the NEC
protocol.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adding a simple Manchester encoder to rc-core.
Manchester coding is used by at least RC-5 and RC-6 protocols and their
variants.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a callback to raw ir handlers for encoding and modulating a scancode
to a set of raw events. This could be used for transmit, or for
converting a wakeup scancode to a form that is more suitable for raw
hardware wake up filters.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
unknown and other are for IR protocols for which we have no decoder,
so the raw IR drivers have no chance of generating them. cec is not
an IR protocol.
Signed-off-by: Sean Young <sean@mess.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that we can select the exact variant of the protocol for wakeup
filter, the winbond-cir can use the wakeup filter rather than module
parameters.
Signed-off-by: Sean Young <sean@mess.org>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are two different encodings used for nec32:
- The ir-nec-decoder.c decoder treats it as 32 bit msb first.
- The img-ir decoder/encoder, winbond wakeup, dib0700, ir-ctl userspace,
treat nec32 analogous to necx and nec: 4 bytes, each lsb first. So this
format reverses the 4 bytes.
There are arguments to be had for both formats, but we should not use
different formats in different parts of the kernel. Selecting the second
format introduces the least code churn. It does mean that the TiVo keymap
needs updating.
This change was submitted before as "18bc174 [media] media: rc: change
32bit NEC scancode format", which was reverted because it was unclear
what scancode rc drivers produce. There are now more examples of drivers
which produce nec32 in lsb format.
The TiVo keymap is verified against the Nero Liquid TiVo remote. The
keymap is not for the Tivo DVR remote, which uses rc-5.
Signed-off-by: Sean Young <sean@mess.org>
Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We need to valdiate that scancodes are valid for their protocol; an
incorrect necx scancode could actually be a nec scancode, for example.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
For IR wakeup, a driver has to program the hardware to wakeup at a
specific IR sequence, so it makes no sense to allow multiple wakeup
protocols to be selected. In the same manner the sysfs interface only
allows one scancode to be provided.
In addition, we need to know the specific variant of the protocol.
In short, these changes are made to the wakeup_protocols sysfs entry:
- list all the protocol variants rather than the protocol groups,
e.g. "nec nec-x nec-32" rather than just "nec".
- only allow one protocol variant to be selected rather than multiple
- wakeup_filter can only be set once a protocol has been selected in
wakeup_protocols.
This is an API change, however the only user of this API is the img-ir,
but the wakeup code was never merged to mainline, so it was never used.
Signed-off-by: Sean Young <sean@mess.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are many variants of extended rc5. This implements the 20 bit
version.
Signed-off-by: Sean Young <sean@mess.org>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The 2nd stop bit in rc5 is reused as an inverted 6th command bit in
20 bits rc5x. Currently the rc5x decoder sets the 6th command bit as
an inverted duplicate of the lowest system bit; as a result we do
not have all the command bits.
Note that there are no rc5x keymaps present.
Signed-off-by: Sean Young <sean@mess.org>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Both the iguanair and the technotrend usb ir do not do any timeout
handling in hardware, so timeout is entirely done in
ir_raw_event_store_with_filter(). Any sensible timeout value will
do, so allow it to be set using LIRC_SET_REC_TIMEOUT.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
No timeout is generated by serial_ir since the port only generates
interrupts on edges. Some IR protocols like rc6 and rc5 need a trailing
space or timeout so they know there are no more bits coming.
Without it, the current key will only be reported once some more IR
occurs.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These ioctls should not succeed if the device cannot send. Also make it
clear that these ioctls should return the lirc mode, although the actual
value does not change.
Signed-off-by: Sean Young <sean@mess.org>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since "273b902 [media] lirc_dev: use LIRC_CAN_REC() define" these
ioctls no longer work.
Signed-off-by: Sean Young <sean@mess.org>
Cc: <stable@vger.kernel.org> # v4.8+
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
LIRC_SET_SEND_CARRIER ioctl should not return the carrier used, it
should return 0.
Signed-off-by: Sean Young <sean@mess.org>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The d680_dmb keymap has some new new mappings.
Tested-by: Vincent McIntyre <vincent.mcintyre@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
I think we can get rid of the spinlock protecting the kthread from being
interrupted by a wakeup in certain parts.
Even with the current implementation of the kthread the only lost wakeup
scenario could happen if the wakeup occurs between the kfifo_len check
and setting the state to TASK_INTERRUPTIBLE.
In the changed version we could lose a wakeup if it occurs between
processing the fifo content and setting the state to TASK_INTERRUPTIBLE.
This scenario is covered by an additional check for available events in
the fifo and setting the state to TASK_RUNNING in this case.
In addition the changed version flushes the kfifo before ending
when the kthread is stopped.
With this patch we gain:
- Get rid of the spinlock
- Simplify code
- Don't grep / release the mutex for each individual event but just once
for the complete fifo content. This reduces overhead if a driver e.g.
triggers processing after writing the content of a hw fifo to the kfifo.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop the FSF's postal address from the source code files that typically
contain mostly the license text. Of the 628 removed instances, 578 are
outdated.
The patch has been created with the following command without manual edits:
git grep -l "675 Mass Ave\|59 Temple Place\|51 Franklin St" -- \
drivers/media/ include/media|while read i; do i=$i perl -e '
open(F,"< $ENV{i}");
$a=join("", <F>);
$a =~ s/[ \t]*\*\n.*You should.*\n.*along with.*\n.*(\n.*USA.*$)?\n//m
&& $a =~ s/(^.*)Or, (point your browser to) /$1To obtain the license, $2\n$1/m;
close(F);
open(F, "> $ENV{i}");
print F $a;
close(F);'; done
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
"c77d17c0 [media] lirc: use-after free" introduces two problems:
cdev_del() can be called with a NULL argument, and the kobject_put()
path will cause a double free.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This function just submits the urb much like mceusb_dev_resume; removing
it simplifies mce_request_packet.
Also add missing usb_kill_urb to mce_dev_probe.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Such debug message has a logic to track the IR status,
but it doesn't provide much info. So, get rid of it.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The clock of IR can be provided by the clock provider and controlled
by common clock framework APIs.
Signed-off-by: Ruqiang Ju <juruqiang@huawei.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The address is 13 bits but it was stuffed in an u8, so 5 bits are
missing from the scancode.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While checking why we need i386 checking, I noticed that
the serial code referred at the driver was moved to another
place. Update it to make clear from where such code came from.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Many lirc drivers have their own receive buffers which are freed on
unplug (e.g. ir_lirc_unregister). This means that ir->buf->wait_poll
will be freed directly after unplug so do not remove yourself from the
wait queue.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If you unplug an lirc device while reading from it, you will get an
use after free as the cdev is freed while still in use.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[ 101.457944] ------------[ cut here ]------------
[ 101.457954] WARNING: CPU: 3 PID: 1819 at kernel/sched/core.c:7708 __might_sleep+0x7e/0x80
[ 101.457960] do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffffc0364bc2>] lirc_dev_fop_read+0x292/0x4e0 [lirc_dev]
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In learning mode, you can get much longer messages which can run out
of lengths. The usb message will slightly larger.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The wideband receiver is a little awkward on the redrat3. Data arrives
on a different endpoint, and the learning command must be reissued
every time data is learned.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If redrat3_delete() is called, ensure ep_in and udev members are set
up so we don't dereference null in the error path. Also ensure that
rc dev device exists before we enable the receiver and that the
led urb exists before we create the led device.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cleanup the error logic, removing checks for things that
should be always initialized when the routines are called,
and remove some bogus messages.
[mchehab@s-opensource.com: fix some merge conflicts]
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Rename the pnp driver in sysfs from /sys/bus/pnp/drivers/Winbond CIR
to /sys/bus/pnp/drivers/winbond-cir
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Kernel takes care that interrupts from one source are serialized.
So there's no need to use spinlock_irq_save.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Spinlock nvt_lock is a member of struct nvt_dev and there's no need
to prefix it with nvt_. So remove this prefix.
[mchehab@s-opensource.org: change the prefix also at the open function,
as the patch removing it were not applied (yet?)]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Using a separate spinlock to protect access to substruct tx of struct
nvt_dev doesn't provide any actual benefit. We can use spinlock
nvt_lock to protect all access to struct nvt_dev and get rid of
nvt->tx.lock.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Member pdev of struct nvt_dev is needed only to access &pdev->dev.
We can get rid of this it by using rdev->dev.parent instead
(both point to the same struct device).
Setting rdev->dev.parent can be removed from the probe function
as this is done by devm_rc_allocate_device now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
rc_unregister_device() will first call ir_free_table(), and later
device_del(); however, the latter causes a call to rc_dev_uevent(),
which prints rc_map.name, which at this point has already bee freed.
This fixes a use-after-free bug found with KASAN.
As reported by Shuah:
"I am seeing the following when I do rmmod on au0828
BUG: KASAN: use-after-free in string+0x170/0x1f0 at addr ffff8801bd513000
Read of size 1 by task rmmod/1831
CPU: 1 PID: 1831 Comm: rmmod Tainted: G W 4.9.0-rc5 #5
Hardware name: Hewlett-Packard HP ProBook 6475b/180F, BIOS 68TTU Ver. F.04 08/03/2012
ffff8801aea2f680 ffffffff81b37ad3 ffff8801fa403b80 ffff8801bd513000
ffff8801aea2f6a8 ffffffff8156c301 ffff8801aea2f738 ffff8801bd513000
ffff8801fa403b80 ffff8801aea2f728 ffffffff8156c59a ffff8801aea2f770
Call Trace:
dump_stack+0x67/0x94
[<ffffffff8156c301>] kasan_object_err+0x21/0x70
[<ffffffff8156c59a>] kasan_report_error+0x1fa/0x4d0
[<ffffffffa116f05f>] ? au0828_exit+0x10/0x21 [au0828]
[<ffffffff8156c8b3>] __asan_report_load1_noabort+0x43/0x50
[<ffffffff81b58b20>] ? string+0x170/0x1f0
[<ffffffff81b58b20>] string+0x170/0x1f0
[<ffffffff81b621c4>] vsnprintf+0x374/0x1c50
[<ffffffff81b61e50>] ? pointer+0xa80/0xa80
[<ffffffff8156b676>] ? save_stack+0x46/0xd0
[<ffffffff81566faa>] ? __kmalloc+0x14a/0x2a0
[<ffffffff81b3d70a>] ? kobject_get_path+0x9a/0x200
[<ffffffff81b408c2>] ? kobject_uevent_env+0x282/0xca0
[<ffffffff81b412eb>] ? kobject_uevent+0xb/0x10
[<ffffffff81f10104>] ? device_del+0x434/0x6d0
[<ffffffffa0fea717>] ? rc_unregister_device+0x177/0x240 [rc_core]
[<ffffffffa116eeb0>] ? au0828_rc_unregister+0x60/0xb0 [au0828]
The problem is fixed with this patch on Linux 4.9-rc4"
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Tested-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is no need to check for CONFIG_COMPAT and consequently
assign the compat_ioctl.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Return directly after a call of the function "rc_allocate_device" failed
at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The local variable "ret" will be set to an appropriate value a bit later.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The local variable "rc" will be set to an appropriate value a bit later.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* Return directly after a call of the function "kcalloc" failed
at the beginning.
* Reorder two calls for the function "kfree" at the end.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the specification of a data type by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script "checkpatch.pl" pointed information out like the following.
WARNING: Possible unnecessary 'out of memory' message
Thus remove such a logging statement in five functions.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* Multiplications for the size determination of memory allocations
indicated that array data structures should be processed.
Thus use the corresponding function "kcalloc".
This issue was detected by using the Coccinelle software.
* Replace the specification of data types by pointer dereferences
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of calling printk() directly, use pr_foo() macro.
That should make the rc_core messages be formatted with the
right prefix.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/media/rc/meson-ir.ko | grep alias
$
After this patch:
$ modinfo drivers/media/rc/meson-ir.ko | grep alias
alias: of:N*T*Camlogic,meson-gxbb-irC*
alias: of:N*T*Camlogic,meson-gxbb-ir
alias: of:N*T*Camlogic,meson8b-irC*
alias: of:N*T*Camlogic,meson8b-ir
alias: of:N*T*Camlogic,meson6-irC*
alias: of:N*T*Camlogic,meson6-ir
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Simplify the remove function and the error path in the probe function by
using the managed versions of rc_allocate_device and rc_register_device.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Introduce managed versions of both functions.
They allows to simplify the error path in the probe function of
rc drivers, and usually also to simplify the remove function.
New element managed_alloc in struct rc_dev is needed to correctly
handle mixed use, e.g. managed version of rc_register_device and
normal version of rc_allocate_device.
In addition devm_rc_allocate_device sets rc->dev.parent as having a
reference to the parent device might be useful for future extensions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Changing available_protocols to atomic64_t allows to get rid of the
mutex protecting access to the variable. This helps to simplify
the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is only one waiter for the completion, therefore there is no need
to use complete_all(). Let's make that clear by using complete() instead
of complete_all().
While we are at it, we do a small optimization with the reinitialization
of the completion before we use it.
The usage pattern of the completion is:
waiter context waker context
send_packet()
init_completion()
usb_submit_urb()
wait_for_completion_interruptible()
usb_tx_callback()
complete()
imon_disonnect()
complete()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Function ite_set_carrier_params() uses variable use_demodulator after
having initialized it to false in some if branches, but this variable is
never set to true otherwise.
This bug has been found using clang -Wsometimes-uninitialized warning
flag.
Fixes: 620a32bba4 ("[media] rc: New rc-based ite-cir driver for
several ITE CIRs")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit 563873318d ("Merge branch 'printk-cleanups"),
continuation lines require KERN_CONT. Instead, let's just
use %*ph to print the buffer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=JqCR
-----END PGP SIGNATURE-----
Merge tag 'media/v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation improvements: conversion of all non-DocBook documents
to Sphinx and lots of fixes to the uAPI media book
- New PCI driver for Techwell TW5864 media grabber boards
- New SoC driver for ATMEL Image Sensor Controller
- Removal of some obsolete SoC drivers (s5p-tv driver and soc_camera
drivers)
- Addition of ST CEC driver
- Lots of drivers fixes, improvements and additions
* tag 'media/v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (464 commits)
[media] ttusb_dec: avoid the risk of go past buffer
[media] cx23885: Fix some smatch warnings
[media] si2165: switch to regmap
[media] si2165: use i2c_client->dev instead of i2c_adapter->dev for logging
[media] si2165: Remove legacy attach
[media] cx231xx: attach si2165 driver via i2c_client
[media] cx231xx: Prepare for attaching new style i2c_client DVB demod drivers
[media] cx23885: attach si2165 driver via i2c_client
[media] si2165: support i2c_client attach
[media] si2165: avoid division by zero
[media] rcar-vin: add R-Car gen2 fallback compatibility string
[media] lgdt3306a: remove 20*50 msec unnecessary timeout
[media] cx25821: Remove deprecated create_singlethread_workqueue
[media] cx25821: Drop Freeing of Workqueue
[media] cxd2841er: force 8MHz bandwidth for DVB-C if specified bw not supported
[media] redrat3: hardware-specific parameters
[media] redrat3: remove hw_timeout member
[media] cxd2841er: BER and SNR reading for ISDB-T
[media] dvb-usb: avoid link error with dib3000m{b,c|
[media] dvb-usb: split out common parts of dibusb
...
Driver updates for ARM SoCs, including a couple of newly added drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for the
EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GvTq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for
the EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
bus: qcom-ebi2: depend on HAS_IOMEM
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
clocksource: exynos_mct: Add the support for ARM64
perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
bus: qcom: add EBI2 driver
bus: qcom: add EBI2 device tree bindings
rtc: rtc-pm8xxx: Add support for pm8018 rtc
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
soc: qcom: smd: Reset rx tail rather than tx
memory: atmel-sdramc: fix a possible NULL dereference
reset: hi6220: allow to compile test driver on other architectures
reset: zynq: add driver Kconfig option
reset: sunxi: add driver Kconfig option
reset: stm32: add driver Kconfig option
reset: socfpga: add driver Kconfig option
...
Add these options as module parameters for now; should other drivers
need similar options we could add it to the LIRC api.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is a duplicate of the timeout in rc_dev.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently we do not know what variant (bit length) of the nec protocol
is used, other than from guessing from the length of the scancode. Now
nec will be handled the same way as the sony protocol or the rc6 protocol;
one variant per bit length.
In the future we might want to expose the rc protocol type to userspace
and we don't want to be introducing this world of pain into userspace
too.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When reporting decoded protocol use the enum rather than the bitmap.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ir_raw_event_handle is called anyway after the hw fifo content stored
in nvt->buf[] has been written to the kfifo. There is not really a
benefit in the potential additional call to ir_raw_event_handle
whilst nvt->buf[] is being processed.
Getting rid of this additional call allows to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The call to nvt_get_rx_ir_data and nvt_process_rx_ir_data from
the ISR is protected with spinlock nvt->lock. Therefore it's
guaranteed that nvt->pkts is 0 when entering nvt_get_rx_ir_data
(as nvt->pkts is set to 0 at the end of nvt_process_rx_ir_data).
Having said that we can remove b_idx.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When removing module nuvoton-cir I get a fifo overrun warning.
It turned out to be caused by a spurious interrupt when the logical CIR
device is being disabled (although no interrupt source bit being set).
Reading the interrupt status register returns 0xff, therefore the fifo
overrun bit is mistakenly interpreted as being set.
Fix this by ignoring interrupts when interrupt source and status register
reads return 0xff.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This partly reverts commit 078600f514.
Due to the relocation of input_register_device() call, holding down a
button on an IR remote no longer resulted in repeated key down events.
Signed-off-by: Ole Ernst <olebowle@gmx.com>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Trivial fix to spelling mistake in dev_err message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer SoCs (Meson 8b and GXBB) are using REG2 (offset 0x20) instead of
REG1 to configure the decoder mode. This makes it necessary to
introduce new bindings so the driver knows which register has to be
used.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Fix this sparse warning:
drivers/media/rc/redrat3.c:490:18: warning: incorrect type in assignment (different base types)
drivers/media/rc/redrat3.c:495:9: warning: cast to restricted __be32
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
Instead of hardcoding a timeout, let userspace change it dynamically
by adding a s_timeout ops.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The redrat3 sends an usb packet to the host either when the minimum pause
or the timeout occurs, so we can always add a trailing space in our
processing.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
LIRC_SET_SEND_CARRIER should return 0 on success or -errno.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When s_tx_mask is given an invalid bitmask, the number of transmitters
should be returned. See the LIRC_SET_TRANSMITTER_MASK lirc ioctl
documentation.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If a system configures the Nuvoton chip to use the alternative
EFM IO address (CR_EFIR2) then after probing the primary EFM IO
address (CR_EFIR) this region is not released.
If a driver for another function of the Nuvoton Super I/O
chip uses the same probing mechanism then it will hang if
loaded after the nuvoton-cir driver.
This was reported for the nct6775 hwmon driver.
Fix this by properly releasing the region after probing CR_EFIR.
This regression was introduced with kernel 4.6 so cc it to stable.
Reported-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Antti Seppälä <a.seppala@gmail.com>
Cc: <stable@vger.kernel.org> # 4.6.x-
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The LIRC_CAN_REC() returns a boolean "flag & LIRC_CAN_REC_MASK"
to check whether the device can receive data.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When opening or closing a lirc character device, the framework
provides to the user the possibility to keep track of opening or
closing of the device by calling two functions:
- set_use_inc() when opening the device
- set_use_dec() when closing the device
if those are not set by the lirc user, the system segfaults.
Check the pointer value before calling the above functions.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If ioctl is called, it cannot be a case of invalid system call
number (ENOSYS), that is a ENOTTY case which means that the
device doesn't support that specific ioctl command.
So, replace ENOSYS with ENOTTY.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When comparing a variable with a constant, the comparison should
start from the variable and not from the constant. It's also
written in the human DNA.
Swap the terms of comparisons whenever the constant comes first
and fix the following checkpatch warning:
WARNING: Comparisons should place the constant on the right side of the test
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The three if statements check the same thing, merge them in only
one statement.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are two if ... else which check the same thing in different
part of the code, they can be merged in a single check.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The whole function is inside an 'if' statement
("if (ir->d.add_to_buf)").
Check the opposite of that statement at the beginning and exit,
this way we can have one level less of indentation.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The code can be rearranged so that some goto paths can be removed
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch mutes also all the checkpatch warnings related to
printk.
Reword all the printouts so that the string doesn't need to be
split, which fixes the following checkpatch warning:
WARNING: quoted string split across lines
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Transmitters don't necessarily need to have a FIFO managed buffer
for their transfers.
When registering the driver, before allocating the buffer, check
whether the device is a transmitter or receiver. Allocate the
buffer only for receivers.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
During the driver registration, move the buffer allocation on a
separate function.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Converts the dtt200u DVB USB driver over to the rc-core
infrastructure for its handling of IR remotes. This device can receive
generic NEC / NEC Extended signals and the switch to the newer core
enables the easy use of tools such as ir-keytable to modify the active
key map.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix RC5 decoding with Fintek CIR chipset
Commit e87b540be2 tightened up the RC5
decoding by adding a check for trailing silence to ensure a valid RC5
command had been received. Unfortunately the trailer length checked was
10 units and the Fintek CIR device does not want to provide details of a
space longer than 6350us. This meant that RC5 remotes working on a
Fintek setup on 3.16 failed on 3.17 and later. Fix this by shortening
the trailer check to 6 units (allowing for a previous space in the
received remote command).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=117221
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Cc: stable@vger.kernel.org
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These two fields are not used and can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the logical device is disabled then it can not generate interrupts.
Therefore this check is not needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Study states have never been used and are not needed. Remove them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The definition of rawir includes the initialization already.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Wake states have never been in use and now that we can set the
wakeup sequence via sysfs there's in general no need for them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The registers defining wakeup sequence handling are set when the
wakeup sequence is set via sysfs. There's no need to initialize them
otherwise.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is a rudimentary ISR for handling interrupts generated by the
wakeup part of the chip. Interrupts however have never been enabled
in the wakeup part.
Also, now that we can set the wakeup sequence via sysfs, there's in
general no need to enable interrupts in the wakeup part.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
To detect a rx fifo overrun it's checked whether the number of elements
in the chip fifo exceeds the fifo size. This check can never return true
and is wrong.
Instead we should generate an interrupt if the fifo overruns.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the rc_map table is created the char pointer of the name of the keymap
is copied to the rc_map->name field. However, this pointer points to memory
from the keymap module itself.
Since these keymap modules are not refcounted, that means anyone can call
rmmod to unload that module. Which is not a big deal because the contents of
the map is all copied to rc_map, except for the keymap name.
So after a keymap module is unloaded the name pointer has become stale. Unloading
the rc-core module will now cause a kernel oops in rc_dev_uevent().
The solution is to kstrdup the name so there are no more references to the
keymap module remaining.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop dmtimer usage for pulse timer in favor of hrtimer. That allows
removing PWM dmitimer platform data usage.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the upcoming removal of legacy boot, lets add support to one of the
last N900 drivers remaining without it. As the driver still uses omap
dmtimer, add auxdata as well.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert driver to use PWM framework instead of calling dmtimer functions
directly for PWM timer. Remove paragraph about writing to the Free Software
Foundation's mailing address while at it.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ir-rx51 driver for n900 has been disabled since the multiarch
changes as plat include directory no longer is SoC specific.
Let's fix it with minimal changes to pass the dmtimer calls in
pdata. Then the following changes can be done while things can
be tested to be working for each change:
1. Change the non-pwm dmtimer to use just hrtimer if possible
2. Change the pwm dmtimer to use Linux PWM API with the new
drivers/pwm/pwm-omap-dmtimer.c and remove the direct calls
to dmtimer functions
3. Parse configuration from device tree and drop the pdata
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Add handling of remote control events coming from the HDMI CEC bus
and the new protocol required for that.
Signed-off-by: Kamil Debski <kamil@wypas.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CONFIG_DEBUG_KOBJECT_RELEASE found this bug.
Signed-off-by: Max Kellermann <max@duempel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add USB ID of SMK RXX6000 series IR receiver. Often branded as
Lenovo receiver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
New USB ID for Adaptec eHome receiver in some HP laptops.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Access to dev->initialized is atomic and dev->initialized isn't
accessed in any other code protected by this mutex.
Therefore we don't need to get the mutex here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Passing overlapping source and destination to snprintf is
fragile. Replace with a single (mostly) equivalent call. If one wants
to preserve the space preceding udev->product whether or not there was
a manufacturer, just remove udev->manufacturer from the && expression.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It makes the printk cleaner. As a side efect, it also fixes those smatch
warnings:
drivers/media/rc/mceusb.c:590 mceusb_dev_printdata() warn: argument 6 to %02x specifier has type 'char'
drivers/media/rc/mceusb.c:590 mceusb_dev_printdata() warn: argument 7 to %02x specifier has type 'char'
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Switch attribute wakeup_data from binary to a text attribute.
This makes it easier to handle in userspace and allows to
use the output of tools like mode2 almost as is to set a
wakeup sequence.
Changing to a text format and values in microseconds also
makes the userspace interface independent of the setting of
SAMPLE_PERIOD in the driver.
In addition document the new sysfs attribute in
Documentation/ABI/testing/sysfs-class-rc-nuvoton.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
MODULE_DEVICE_TABLE() is missing, so the module isn't auto-loading on
systems supporting infrared. This commit adds the missing line so it
works out of the box when built as a module and running on a sunxi
system with an infrared receiver.
Signed-off-by: Emilio López <emilio.lopez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since rc_allocate_device() uses kmalloc, it can returns NULL,
so need to check, otherwise, NULL derefenrece can happen.
Reported-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix AverMedia RM-KS keymap using user guide to meet LinuxTV wiki rules.
The remote command didn't seem to change in itself since its creation: it's
just to make keys more standard and remove the FIXME.
Signed-off-by: Philippe Valembois <lephilousophe@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds a binary attribute /sys/class/rc/rc?/wakeup_data which
allows to read / write the wakeup sequence.
In combination with the core extension for exposing the most recent raw
packet this allows to easily define and set a wakeup sequence.
At least on my Zotac CI321 the BIOS resets the wakeup sequence at each boot
to a factory default. Therefore I use a udev rule
SUBSYSTEM=="rc", DRIVERS=="nuvoton-cir", ACTION=="add", RUN+="<script>"
with the script basically doing
cat <stored wakeup sequence> >/sys${DEVPATH}/wakeup_data
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The device initialization completes only after calling
input_register_device(). However, rc_open() can be called while
the device is being registered by the input/evdev core. So, we
can't expect that rc_dev->initialized to be true.
Change the logic to don't require initialized == true at rc_open
and change the type of initialized to be atomic.
this way, we can check for it earlier where it is really needed,
without needing to lock the mutex just for testing it.
Tested with nuvoton_cir driver on a NUC5i7RYB with CIR integrated on it.
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We can only unlock if mutex_lock() succeeds.
Fixes the following warning:
drivers/media/rc/lirc_dev.c:535 lirc_dev_fop_close() error: double unlock 'mutex:&lirc_dev_lock'
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of having the timeouts hardcoded, and getting only the
accel value from the array, put everything in the same place.
That simplifies the logic.
As a side effect, it also cleans several smatch errors:
include/linux/jiffies.h:359:41: error: strange non-value function or array
include/linux/jiffies.h:361:42: error: strange non-value function or array
(one per time_after/time_before line)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The mutex lock at rc_register_device() was added by commit 08aeb7c9a4
("[media] rc: add locking to fix register/show race").
It is meant to avoid race issues when trying to open a sysfs file while
the RC register didn't complete.
Adding a lock there causes troubles, as detected by the Kernel lock
debug instrumentation at the Kernel:
======================================================
[ INFO: possible circular locking dependency detected ]
4.5.0-rc3+ #46 Not tainted
-------------------------------------------------------
systemd-udevd/2681 is trying to acquire lock:
(s_active#171){++++.+}, at: [<ffffffff8171a115>] kernfs_remove_by_name_ns+0x45/0xa0
but task is already holding lock:
(&dev->lock){+.+.+.}, at: [<ffffffffa0724def>] rc_register_device+0xb2f/0x1450 [rc_core]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&dev->lock){+.+.+.}:
[<ffffffff8124817d>] lock_acquire+0x13d/0x320
[<ffffffff822de966>] mutex_lock_nested+0xb6/0x860
[<ffffffffa0721f2b>] show_protocols+0x3b/0x3f0 [rc_core]
[<ffffffff81cdaba5>] dev_attr_show+0x45/0xc0
[<ffffffff8171f1b3>] sysfs_kf_seq_show+0x203/0x3c0
[<ffffffff8171a6a1>] kernfs_seq_show+0x121/0x1b0
[<ffffffff81617c71>] seq_read+0x2f1/0x1160
[<ffffffff8171c911>] kernfs_fop_read+0x321/0x460
[<ffffffff815abc20>] __vfs_read+0xe0/0x3d0
[<ffffffff815ae90e>] vfs_read+0xde/0x2d0
[<ffffffff815b1d01>] SyS_read+0x111/0x230
[<ffffffff822e8636>] entry_SYSCALL_64_fastpath+0x16/0x76
-> #0 (s_active#171){++++.+}:
[<ffffffff81244f24>] __lock_acquire+0x4304/0x5990
[<ffffffff8124817d>] lock_acquire+0x13d/0x320
[<ffffffff81717d3a>] __kernfs_remove+0x58a/0x810
[<ffffffff8171a115>] kernfs_remove_by_name_ns+0x45/0xa0
[<ffffffff81721592>] remove_files.isra.0+0x72/0x190
[<ffffffff8172174b>] sysfs_remove_group+0x9b/0x150
[<ffffffff81721854>] sysfs_remove_groups+0x54/0xa0
[<ffffffff81cd97d0>] device_remove_attrs+0xb0/0x140
[<ffffffff81cdb27c>] device_del+0x38c/0x6b0
[<ffffffffa0724b8b>] rc_register_device+0x8cb/0x1450 [rc_core]
[<ffffffffa1326a7b>] dvb_usb_remote_init+0x66b/0x14d0 [dvb_usb]
[<ffffffffa1321c81>] dvb_usb_device_init+0xf21/0x1860 [dvb_usb]
[<ffffffffa13517dc>] dib0700_probe+0x14c/0x410 [dvb_usb_dib0700]
[<ffffffff81dbb1dd>] usb_probe_interface+0x45d/0x940
[<ffffffff81ce7e7a>] driver_probe_device+0x21a/0xc30
[<ffffffff81ce89b1>] __driver_attach+0x121/0x160
[<ffffffff81ce21bf>] bus_for_each_dev+0x11f/0x1a0
[<ffffffff81ce6cdd>] driver_attach+0x3d/0x50
[<ffffffff81ce5df9>] bus_add_driver+0x4c9/0x770
[<ffffffff81cea39c>] driver_register+0x18c/0x3b0
[<ffffffff81db6e98>] usb_register_driver+0x1f8/0x440
[<ffffffffa074001e>] dib0700_driver_init+0x1e/0x1000 [dvb_usb_dib0700]
[<ffffffff810021b1>] do_one_initcall+0x141/0x300
[<ffffffff8144d8eb>] do_init_module+0x1d0/0x5ad
[<ffffffff812f27b6>] load_module+0x6666/0x9ba0
[<ffffffff812f5fe8>] SyS_finit_module+0x108/0x130
[<ffffffff822e8636>] entry_SYSCALL_64_fastpath+0x16/0x76
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&dev->lock);
lock(s_active#171);
lock(&dev->lock);
lock(s_active#171);
*** DEADLOCK ***
3 locks held by systemd-udevd/2681:
#0: (&dev->mutex){......}, at: [<ffffffff81ce8933>] __driver_attach+0xa3/0x160
#1: (&dev->mutex){......}, at: [<ffffffff81ce8941>] __driver_attach+0xb1/0x160
#2: (&dev->lock){+.+.+.}, at: [<ffffffffa0724def>] rc_register_device+0xb2f/0x1450 [rc_core]
In this specific case, some error happened during device init,
causing IR to be disabled.
Let's fix it by adding a var that will tell when the device is
initialized. Any calls before that will return a -EINVAL.
That should prevent the race issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
nvt_disable_cir calls nvt_disable_logical_dev (that may sleep) and is
called from contexts holding a spinlock.
Fix this and remove the unneeded clearing of CIR_IREN as this is done
in nvt_cir_disable already.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
nvt_enable_wake calls nvt_select_logical_dev (that may sleep) and is called
from contexts holding a spinlock. Fix this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
nvt_enable_cir calls nvt_enable_logical_dev (that may sleep)
while holding a spinlock.
This patch fixes this and moves the content of nvt_enable_cir
to nvt_open as this is the only caller.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Extend the locking to protect more critical actions like register accesses
in the interrupt handlers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Only handle an interrupt if at least one combination of event bit
and related interrupt bit is set.
Previously it was just checked that at least one event bit and
at least one interrupt bit are set.
This fixes issues like the following which was caused by
interrupt sharing:
An interrupt intended for nvt_cir_isr was handled by nvt_cir_wake_isr
first and because status bit CIR_WAKE_IRSTS_IR_PENDING was set
the wake fifo was accidently cleared.
This patch also fixes the bug that nvt_cir_wake_isr returned IRQ_HANDLED
even if it detected that the (shared) interrupt was meant for another
handler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Check for the case that no Nuvoton chip is found on either EFM port.
Also move the position of nvt_efm_disable to reduce the time the
EFM ports are locked.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
At least on Zotac CI321 ACPI provides an ioport range for the wake up part
but accessing these ioports has no effect.
Instead the ioport base address is set to another value already
(0xa20 in my case) and accessing this ioport range works.
Therefore set a new ioport base address only if the current ioport base
address is 0 (register reset default).
The need to use the existing base address instead of trying to set
an own one doesn't seem to be limited to this specific device as other
drivers like hwmon/nct6775 do it the same way.
This change was successfully tested on the mentioned device.
And the change should be generic enough to not break the driver for
other chips (however due to lack of appropriate hardware I wasn't
able to test this).
[mchehab@osg.samsung.com: Tested on Intel NUC NUC5i7RYB with BIOS
version RYBDWi35.86A.0350.2015.0812.1722]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Calling nvt_set_cir_iren separately is not needed as this is done
by nvt_cir_regs_init.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Selecting the logical device in the interrupt handler is not needed
as no configuration register is accessed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Only enable the logical devices after the registers have been initialized.
The call to nvt_enable_logical_dev in nvt_resume is not needed as this is
done implicitely by nvt_cir_regs_init now.
[mchehab@osg.samsung.com: fixed multiline comment to kernel CodingStyle]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Switch to using the recently introduced IR default timeout value
(IR_DEFAULT_TIMEOUT) and consider the value of SAMPLE_PERIOD
when calculating the limit count register value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
At least on NVT6779D clearing the wake fifo works in learning mode only
(although this condition is not mentioned in the chip spec).
Setting the clear fifo bit has no effect in wake up mode.
Even if clearing the wake fifo should work in wake up mode on other
chips this workaround doesn't hurt.
If needed the caller of nvt_clear_cir_wake_fifo has to take care
of locking.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The two EFM ioports are accessed by drivers for other parts of the Nuvoton
Super-IO chips too. Therefore access to these ioports needs to be
protected by using request_muxed_region (like it's implemented e.g. in
hwmon/nct6775 already).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The FIFO is used for ir_raw_event records, however for some historic
reason the FIFO is used on a per byte basis. IMHO this adds unneeded
complexity. Therefore set up the FIFO for ir_raw_event records.
This also allows to define the FIFO statically as part of
ir_raw_event_ctrl instead of having to allocate the FIFO dynamically.
In addition:
- When writing into the FIFO and it's full return ENOSPC instead of
ENOMEM thus making it easier to tell between "FIFO full" and
"Dynamic memory allocation failed" when the error is propagated to
a higher level.
Also add an error message.
- When reading from the FIFO check whether it's empty.
This is not strictly needed here but kfifo_out is annotated
"must check" anyway.
Successfully tested it with the nuvoton-cir driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When requesting resources use different names for the normal and
the wakeup part. This makes it easier to interpret the output
of e.g. /proc/interrupts and /proc/ioports.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The driver allocates the spinlock but fails to initialize it correctly.
The kernel reports a BUG indicating bad spinlock magic when spinlock
debugging is enabled.
Call spin_lock_init() on it to initialize it correctly.
Fixes: b4e3e59fb5 ("[media] rc: add sunxi-ir driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that that the decoder modules are loaded on-demand we can move
loading the lirc module to rc_register_device directly and remove
unneeded functions and comments.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Checking whether a protocol is enabled and calling the related decoder
functions should be done by the rc core, not the protocol handlers.
Properly handle lirc considering that no protocol bit is set for lirc.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Declare struct proto_names and its member name as const.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Prepare on-demand decoder module loading by adding a module_name member
to struct proto_names and introducing the related load function.
After this patch of the series the decoder modules are still loaded
unconditionally.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, if a decoder module is unloadad, the respective protocol
is still shown as enabled (if it was enabled before).
Fix this by resetting the respective protocol bits if a decoder
module is unloaded.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Simplify the logging.
I had some doubts about using the elvis operator as it's GNU extension.
However GNU extensions are explicitely allowed and this operator is
used at several places in the kernel code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Switch the info about the detected chip type from debug to info level
as it might be useful not only for debugging purposes.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of explicitely checking debug use nvt_dbg like in other parts
of the driver thus simplifying the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the NCT6779D. It's found e.g. on the Zotac CI321 mini-pc
and I successfully tested it on this device.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the chip detection code more similar to the one used for the
same chips in watchdog/w83627hf_wdt.c and hwmon/w83627ehf.c.
Apart from better maintainability we gain
- unified naming of chips (e.g. 677C -> NCT6776F)
- driver works with all revisions of the chips
(least 4 bits of id are masked)
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using IRQ_RETVAL is unneeded here. IRQ_NONE / IRQ_HANDLED can be
returned directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Denon also uses the Sharp protocol, however with different check bits.
It would have been also possible to add this as a separate protocol
but this may not be worth the effort.
Successfully tested with a Denon RC-1002 remote control.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
streamzap uses 'struct timeval' to store the start time of a signal for
gap tracking. struct timeval uses a 32-bit seconds representation which
will overflow in year 2038 and beyond. Replace struct timeval with ktime_t
which uses a 64-bit seconds representation and is 2038 safe. This patch
uses ktime_get_real() preserving the use of wall-clock time in the
original code.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
rc-main mistakenly uses #ifdef MODULE to determine whether it should
load the rc keymap modules. This symbol is only defined if rc-main
is being built as a module itself, and bears no relation to whether
the rc keymaps are modules.
Fix this to use CONFIG_MODULES instead.
Fixes: 631493ecac ("[media] rc-core: merge rc-map.c into rc-main.c")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Many decoders require a trailing space (period without IR illumination)
to be delivered before completing a decode.
Since the gpio-ir-recv driver only delivers events on gpio transitions,
a single IR symbol (caused by a quick touch on an IR remote) will not
be properly decoded without the use of a timer to flush the tail end
state of the IR receiver.
This patch initializes and uses a timer and the timeout field of rcdev
to complete the stream and allow decode.
The timeout can be overridden through the use of the LIRC_SET_REC_TIMEOUT
ioctl.
Signed-off-by: Eric Nelson <eric@nelint.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The device is set as wakeup capable using proper wakeup API but the
driver misuses IRQF_NO_SUSPEND to set the interrupt as wakeup source
which is incorrect.
This patch removes the use of IRQF_NO_SUSPEND flags replacing it with
enable_irq_wake instead.
Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: kernel@stlinux.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Let's not mix platform_data headers with the core headers. Instead, let's
create a subdir at linux/platform_data and move the headers to that
common place, adding it to MAINTAINERS.
The headers were moved with:
mkdir include/linux/platform_data/media/; git mv include/media/gpio-ir-recv.h include/media/ir-rx51.h include/media/mmp-camera.h include/media/omap1_camera.h include/media/omap4iss.h include/media/s5p_hdmi.h include/media/si4713.h include/media/sii9234.h include/media/smiapp.h include/media/soc_camera.h include/media/soc_camera_platform.h include/media/timb_radio.h include/media/timb_video.h include/linux/platform_data/media/
And the references fixed with this script:
MAIN_DIR="linux/platform_data/"
PREV_DIR="media/"
DIRS="media/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This driver doesn't claim the IR transmitter to be wakeup source. It
even disables the clock and the IR during suspend-resume cycle.
This patch removes yet another misuse of IRQF_NO_SUSPEND.
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Guoxiong Yan <yanguoxiong@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cIed
-----END PGP SIGNATURE-----
Merge tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new DVB frontend drivers: ascot2e, cxd2841er, horus3a, lnbh25
- new HDMI capture driver: tc358743
- new driver for NetUP DVB new boards (netup_unidvb)
- IR support for DVBSky cards (smipcie-ir)
- Coda driver has gain macroblock tiling support
- Renesas R-Car gains JPEG codec driver
- new DVB platform driver for STi boards: c8sectpfe
- added documentation for the media core kABI to device-drivers DocBook
- lots of driver fixups, cleanups and improvements
* tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (297 commits)
[media] c8sectpfe: Remove select on undefined LIBELF_32
[media] i2c: fix platform_no_drv_owner.cocci warnings
[media] cx231xx: Use wake_up_interruptible() instead of wake_up_interruptible_nr()
[media] tc358743: only queue subdev notifications if devnode is set
[media] tc358743: add missing Kconfig dependency/select
[media] c8sectpfe: Use %pad to print 'dma_addr_t'
[media] DocBook media: Fix typo "the the" in xml files
[media] tc358743: make reset gpio optional
[media] tc358743: set direction of reset gpio using devm_gpiod_get
[media] dvbdev: document most of the functions/data structs
[media] dvb_frontend.h: document the struct dvb_frontend
[media] dvb-frontend.h: document struct dtv_frontend_properties
[media] dvb-frontend.h: document struct dvb_frontend_ops
[media] dvb: Use DVBFE_ALGO_HW where applicable
[media] dvb_frontend.h: document struct analog_demod_ops
[media] dvb_frontend.h: Document struct dvb_tuner_ops
[media] Docbook: Document struct analog_parameters
[media] dvb_frontend.h: get rid of dvbfe_modcod
[media] add documentation for struct dvb_tuner_info
[media] dvb_frontend: document dvb_frontend_tune_settings
...
This reverts commit 9869da5bac.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 1d971d927e.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit a0466f15b4.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit cf257e288a.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 0d830b2d12.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 2e4ebde269.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit da7ee60b03.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 275ddb40bc removed the lirc
"protocol" but kept backwards compatibility by always listing
the protocol as present and enabled. This patch further improves
the logic by only listing the protocol if the lirc module is loaded
(or if lirc is builtin).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This changes the keymap back to the state before commit 616a4b83
and changes the driver to use full NEC32 scancodes following the
instructions provided by Malcolm Priestley <tvboxspy@gmail.com>.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The LIRC protocol was always a bad fit and if we're ever going to expose
protocol numbers in a user-space API, it'd be better to get rid of the
LIRC "protocol" first.
The sysfs API is kept backwards compatible by always listing the lirc
protocol as present and enabled.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch changes rc-core to use the kernel facilities that are already
available for handling unique numbers instead of rolling its own bitmap
stuff.
Signed-off-by: David Härdeman <david@hardeman.nu>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The input_dev is already gone when the rc device is being unregistered
so checking for its presence only means that no remove uevent will be
generated.
Cc: stable@kernel.org
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The RC_ST and IR_SUNXI entries have weird indentation, and the RC_ST
entry is actually malformed. Fix it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using CONFIG_PM_SLEEP suppress the warnings when the driver is
compiled without PM sleep functions:
drivers/media/rc/st_rc.c:338:12: warning: ‘st_rc_suspend’ defined but not used [-Wunused-function]
drivers/media/rc/st_rc.c:359:12: warning: ‘st_rc_resume’ defined but not used [-Wunused-function]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
This RC map was taken from Christoph Pinkl's patch
(http://patchwork.linuxtv.org/patch/7217/). It is used solely by the respective
mantis based card because the encoding is not known.
Signed-off-by: Jan Klötzke <jan@kloetzke.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This RC map was taken from Christoph Pinkl's patch
(http://patchwork.linuxtv.org/patch/7217/). It is used solely by the respective
mantis based card because the encoding is not known.
Signed-off-by: Jan Klötzke <jan@kloetzke.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This RC map was taken from Christoph Pinkl's patch
(http://patchwork.linuxtv.org/patch/7217/). It is used solely by the respective
mantis based card because the encoding is not known.
Signed-off-by: Jan Klötzke <jan@kloetzke.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The TS35 remote is distributed with TechniSat CableStar HD2 cards (mantis
chipset). The exact protocol type is unknown, making this rc map probably only
usable by mantis cards.
Signed-off-by: Jan Klötzke <jan@kloetzke.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Don't allow sleep when getting the gpio value in the irq-handler.
On my rk3288 board this results in might_sleep warnings when receiving
data like:
BUG: sleeping function called from invalid context at drivers/gpio/gpiolib.c:1531
in_atomic(): 1, irqs_disabled(): 128, pid: 0, name: swapper/0
CPU: 0 PID: 0 Comm: swapper/0 Tainted: P 4.1.0-rc5+ #2011
Hardware name: Rockchip (Device Tree)
[<c00189a0>] (unwind_backtrace) from [<c0013b04>] (show_stack+0x20/0x24)
[<c0013b04>] (show_stack) from [<c0757970>] (dump_stack+0x8c/0xbc)
[<c0757970>] (dump_stack) from [<c0053188>] (___might_sleep+0x238/0x284)
[<c0053188>] (___might_sleep) from [<c0053264>] (__might_sleep+0x90/0xa4)
[<c0053264>] (__might_sleep) from [<c02ff4ac>] (gpiod_get_raw_value_cansleep+0x28/0x44)
[<c02ff4ac>] (gpiod_get_raw_value_cansleep) from [<bf0363c4>] (gpio_ir_recv_irq+0x24/0x6c [gpio_ir_recv])
[<bf0363c4>] (gpio_ir_recv_irq [gpio_ir_recv]) from [<c008a78c>] (handle_irq_event_percpu+0x164/0x550)
[<c008a78c>] (handle_irq_event_percpu) from [<c008abc4>] (handle_irq_event+0x4c/0x6c)
[<c008abc4>] (handle_irq_event) from [<c008df88>] (handle_edge_irq+0x128/0x150)
[<c008df88>] (handle_edge_irq) from [<c0089edc>] (generic_handle_irq+0x30/0x40)
[<c0089edc>] (generic_handle_irq) from [<c02fc4cc>] (rockchip_irq_demux+0x158/0x210)
[<c02fc4cc>] (rockchip_irq_demux) from [<c0089edc>] (generic_handle_irq+0x30/0x40)
[<c0089edc>] (generic_handle_irq) from [<c008a058>] (__handle_domain_irq+0x98/0xc0)
[<c008a058>] (__handle_domain_irq) from [<c00094a4>] (gic_handle_irq+0x4c/0x70)
[<c00094a4>] (gic_handle_irq) from [<c0014684>] (__irq_svc+0x44/0x5c)
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Nuvoton-cir utilizes the encoding capabilities of rc-core to convert
scancodes from user space to pulse/space format understood by the
underlying hardware.
Converted samples are then written to the wakeup fifo along with other
necessary configuration to enable wake up functionality.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: James Hogan <james@albanarts.com>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the s_wakeup_filter callback to the rc-loopback driver, which instead of
setting the filter just feeds the scancode back through the input device
so that it can be verified.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support in rc-core for drivers which implement the wakeup scancode
filter by encoding the scancode using the raw IR encoders. This is by
way of rc_dev::encode_wakeup which should be set to true to make the
allowed wakeup protocols the same as the set of raw IR encoders.
As well as updating the sysfs interface to know which wakeup protocols
are allowed for encode_wakeup drivers, also ensure that the IR
decoders/encoders are loaded when an encode_wakeup driver is registered.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the capability to encode RC-6 and RC-6A scancodes as raw events.
The protocol is chosen based on the specified protocol mask, and
whether all the required bits are set in the scancode mask, and none of
the unused bits are set in the scancode data.
The Manchester modulation helper is used several times with various
timings so that RC-6 header preamble, the header, header trailing bit
and the data itself can be modulated correctly.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: James Hogan <james@albanarts.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the capability to encode RC-5, RC-5X and RC-5-SZ scancodes as raw
events. The protocol is chosen based on the specified protocol mask,
and whether all the required bits are set in the scancode mask, and
none of the unused bits are set in the scancode data. For example a
scancode filter with bit 16 set in both data and mask is unambiguously
RC-5X.
The Manchester modulation helper is used, and for RC-5X it is used twice
with two sets of timings, the first with a short trailer space for the
space in the middle, and the second with no leader so that it can
continue the space.
The encoding in RC-5-SZ first inserts a pulse and then simply utilizes
the generic Manchester encoder available in rc-core.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adding a simple Manchester encoder to rc-core.
Manchester coding is used by at least RC-5 and RC-6 protocols and their
variants.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: James Hogan <james@albanarts.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a callback to raw ir handlers for encoding and modulating a scancode
to a set of raw events. This could be used for transmit, or for
converting a wakeup scancode filter to a form that is more suitable for
raw hardware wake up filters.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Building for avr32 leads the following build warning:
drivers/media/rc/st_rc.c:270: warning: passing argument 1 of 'IS_ERR' discards qualifiers from pointer target type
drivers/media/rc/st_rc.c:271: warning: passing argument 1 of 'PTR_ERR' discards qualifiers from pointer target type
devm_ioremap_resource() returns void __iomem *, so change 'base' and
'rx_base' definitions accordingly.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Building for avr32 leads the following build warning:
drivers/media/rc/ir-hix5hd2.c:221: warning: passing argument 1 of 'IS_ERR' discards qualifiers from pointer target type
drivers/media/rc/ir-hix5hd2.c:222: warning: passing argument 1 of 'PTR_ERR' discards qualifiers from pointer target type
devm_ioremap_resource() returns void __iomem *, so change 'base' definition
accordingly.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver does not use any PCI IDs, don't include
the pci_ids.h header.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
[mchehab@osg.samsung.com: fix a merge conflict at adv7604.c]
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
redrat3_send_cmd() can return an error or the read data. However,
it currently returns an u8, as reported by smatch:
drivers/media/rc/redrat3.c:416 redrat3_send_cmd() warn: signedness bug returning '(-12)'
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are some false-positive warnings produced by smatch:
drivers/media/rc/ir-sony-decoder.c:129 ir_sony_decode() warn: missing break? reassigning 'data->state'
drivers/media/rc/ir-sony-decoder.c:137 ir_sony_decode() warn: missing break? reassigning 'data->state'
drivers/media/rc/ir-sony-decoder.c:165 ir_sony_decode() warn: missing break? reassigning 'data->state'
This is due to the logic used there to detect the need of a break.
While those are false positives, it is easy to get rid of them without
any drawbacks. The side effect is a cleaner function, with is good.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
