ibuf and rbuf in lme2510_int_response are always assigned to before they
are read, and their addresses do not escape the function, so they have
no reason to be static.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Using the %ph printf extension for hex dumps like this makes the
generated code quite a bit smaller.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drivers might try to access and run enable_source and disable_source
handlers when the driver that implements these handlers is clearing
the handlers during its unregister.
Fix the following race condition:
process 1 process 2
request video streaming unbind au0828
v4l2 checks if tuner is free
... ...
au0828_unregister_media_device()
... ...
(doesn't hold graph_mutex)
mdev->enable_source = NULL;
if (mdev && mdev->enable_source) mdev->disable_source = NULL;
mdev->enable_source()
(enable_source holds graph_mutex)
As shown above enable_source check is done without holding the graph_mutex.
If unbind happens to be in progress, au0828 could clear enable_source and
disable_source handlers leading to null pointer de-reference.
Fix it by protecting enable_source and disable_source set and clear and
protecting enable_source and disable_source handler access and the call
itself.
process 1 process 2
request video streaming unbind au0828
v4l2 checks if tuner is free
... ...
au0828_unregister_media_device()
... ...
(hold graph_mutex while clearing)
mdev->enable_source = NULL;
if (mdev) mdev->disable_source = NULL;
(hold graph_mutex to check and
call enable_source)
if (mdev->enable_source)
mdev->enable_source()
If graph_mutex is held to just heck for handler being null and needs to be
released before calling the handler, there will be another window for the
handlers to be cleared. Hence, enable_source and disable_source handlers
no longer hold the graph_mutex and expect callers to hold it to avoid
forcing them release the graph_mutex before calling the handlers.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ZyDAS ZD1301 is chip having USB interface and DVB-T demodulator
integrated. This driver is for USB interface part.
Device has USB ID 0ace:13a1. Used tuner is MT2060.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The device driver should keep going even if debugfs initialization fails.
So, change the return type to void.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove a superfluous assignment to a local variable at the end of a
function.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add an inline function to obtain a struct uvc_buffer pointer from a
struct vb2_v4l2_buffer one.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Chip uses so called 8-bit i2c addresses, but on bus there is of
course correct 7-bit addresses with rw bit as lsb - verified
with oscilloscope.
Lets still use correct addresses in driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Driver supports 2 different device versions, AX and BX. Use device
IDs to pass chip version information to driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
it913x tuner driver is changed to platform model so we need bind it
using platform_device_register_data().
Also remove hacks from I2C adapter where fake tuner driver address
(addr >> 1) were used as those are no longer needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Read eeprom content to chip state and read values there when needed.
Also debug dump eeprom content.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use space characters at some source code places according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When some other buffer is immediately copied into allocated region.
Replace calls to kmalloc followed by a memcpy with a direct
call to kmemdup.
Signed-off-by: Shyam Saini <mayhs11saini@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
trivial fix to spelling mistake in err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver type can be assigned immediately when an RC device
requests to the framework to allocate the device.
This is an 'enum rc_driver_type' data type and specifies whether
the device is a raw receiver or scancode receiver. The type will
be given as parameter to the rc_allocate_device device.
Change accordingly all the drivers calling rc_allocate_device()
so that the device type is specified during the rc device
allocation. Whenever the device type is not specified, it will be
set as RC_DRIVER_SCANCODE which was the default '0' value.
Suggested-by: Sean Young <sean@mess.org>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
unknown and other are for IR protocols for which we have no decoder,
so the raw IR drivers have no chance of generating them. cec is not
an IR protocol.
Signed-off-by: Sean Young <sean@mess.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The d680_dmb keymap has some new new mappings.
Tested-by: Vincent McIntyre <vincent.mcintyre@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=r51U
-----END PGP SIGNATURE-----
Merge tag 'media/v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- fix a regression on tvp5150 causing failures at input selection and
image glitches
- CEC was moved out of staging for v4.10. Fix some bugs on it while not
too late
- fix a regression on pctv452e caused by VM stack changes
- fix suspend issued with smiapp
- fix a regression on cobalt driver
- fix some warnings and Kconfig issues with some random configs.
* tag 'media/v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] s5k4ecgx: select CRC32 helper
[media] dvb: avoid warning in dvb_net
[media] v4l: tvp5150: Don't override output pinmuxing at stream on/off time
[media] v4l: tvp5150: Fix comment regarding output pin muxing
[media] v4l: tvp5150: Reset device at probe time, not in get/set format handlers
[media] pctv452e: move buffer to heap, no mutex
[media] media/cobalt: use pci_irq_allocate_vectors
[media] cec: fix race between configuring and unconfiguring
[media] cec: move cec_report_phys_addr into cec_config_thread_func
[media] cec: replace cec_report_features by cec_fill_msg_report_features
[media] cec: update log_addr[] before finishing configuration
[media] cec: CEC_MSG_GIVE_FEATURES should abort for CEC version < 2
[media] cec: when canceling a message, don't overwrite old status info
[media] cec: fix report_current_latency
[media] smiapp: Make suspend and resume functions __maybe_unused
[media] smiapp: Implement power-on and power-off sequences without runtime PM
The media_entity_pipeline_start() and media_entity_pipeline_stop()
functions are renamed as media_pipeline_start() and media_pipeline_stop(),
respectively. The reason is two-fold: the pipeline struct is, rightly,
already called media_pipeline (rather than media_entity_pipeline) and what
this really is about is a pipeline. A pipeline consists of entities ---
and, well, other objects embedded in these entities.
As the pipeline object will be in the future moved from entities to pads
in order to support multiple pipelines through a single entity, do the
renaming now.
Similarly, functions operating on struct media_entity_graph as well as the
struct itself are renamed by dropping the "entity_" part from the prefix
of the function family and the data structure. The graph traversal which
is what the functions are about is not specifically about entities only
and will operate on pads for the same reason as the media pipeline.
The patch has been generated using the following command:
git grep -l media_entity |xargs perl -i -pe '
s/media_entity_pipeline/media_pipeline/g;
s/media_entity_graph/media_graph/g'
And a few manual edits related to line start alignment and line wrapping.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop the FSF's postal address from the source code files that typically
contain mostly the license text. Of the 628 removed instances, 578 are
outdated.
The patch has been created with the following command without manual edits:
git grep -l "675 Mass Ave\|59 Temple Place\|51 Franklin St" -- \
drivers/media/ include/media|while read i; do i=$i perl -e '
open(F,"< $ENV{i}");
$a=join("", <F>);
$a =~ s/[ \t]*\*\n.*You should.*\n.*along with.*\n.*(\n.*USA.*$)?\n//m
&& $a =~ s/(^.*)Or, (point your browser to) /$1To obtain the license, $2\n$1/m;
close(F);
open(F, "> $ENV{i}");
print F $a;
close(F);'; done
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYYGCgAAoJEHm+PkMAQRiGjVMH/R1WKLSCVyU2QboSTZVyBGqU
6E42pMalPNaY72uxf29ZmUzds1uV5KyFn7OntsyD4qc+sQb2wxG5PvMSYAsL7HKN
lTFiW738zC9Hfx8MzC/fHLGm/7HTHpPFndZJkDOJjIPnS0MeTHAmOFM+RwCRq+px
5uvRHV4Z8yibHtijET6GqCywV0gw/uyXCi6xJfJNAspnj3hsm3ZXKJ0JPvP2ja+V
yhdnWYHDEQwRs6FyNtIWnfjH92XilVn4KcOtwnb1pFahALiTmmVqJVMiGartagqJ
fPRw98B3YHwmZpEc2SDbXaZi36WLu4hcWvvDa22SN/srXwYIzzblEwuNq1+fiBw=
=X7z+
-----END PGP SIGNATURE-----
Merge tag 'v4.10-rc1' into patchwork
Linux 4.10-rc1
* tag 'v4.10-rc1': (11427 commits)
Linux 4.10-rc1
powerpc: Fix build warning on 32-bit PPC
avoid spurious "may be used uninitialized" warning
mm: add PageWaiters indicating tasks are waiting for a page bit
mm: Use owner_priv bit for PageSwapCache, valid when PageSwapBacked
ktime: Get rid of ktime_equal()
ktime: Cleanup ktime_set() usage
ktime: Get rid of the union
clocksource: Use a plain u64 instead of cycle_t
irqchip/armada-xp: Consolidate hotplug state space
irqchip/gic: Consolidate hotplug state space
coresight/etm3/4x: Consolidate hotplug state space
cpu/hotplug: Cleanup state names
cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
staging/lustre/libcfs: Convert to hotplug state machine
scsi/bnx2i: Convert to hotplug state machine
scsi/bnx2fc: Convert to hotplug state machine
cpu/hotplug: Prevent overwriting of callbacks
x86/msr: Remove bogus cleanup from the error path
bus: arm-ccn: Prevent hotplug callback leak
...
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 73d5c5c864 ("[media] pctv452e: don't do DMA on stack") caused
a NULL pointer dereference which occurs when dvb_usb_init()
calls dvb_usb_device_power_ctrl() for the first time, before the
frontend has been attached. It also caused a recursive deadlock because
tt3650_ci_msg_locked() has already locked the mutex.
So, partially revert it, but move the buffer to the heap
(DMA capable), not to the stack (may not be DMA capable).
Instead of sharing one buffer which needs mutex protection,
do a new heap allocation for each call.
Fixes: commit 73d5c5c864 ("[media] pctv452e: don't do DMA on stack")
Cc: stable@vger.kernel.org # For Kernel 4.9
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=ADpU
-----END PGP SIGNATURE-----
Merge tag 'media/v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new Mediatek drivers: mtk-mdp and mtk-vcodec
- some additions at the media documentation
- the CEC core and drivers were promoted from staging to mainstream
- some cleanups at the DVB core
- the LIRC serial driver got promoted from staging to mainstream
- added a driver for Renesas R-Car FDP1 driver
- add DVBv5 statistics support to mn88473 driver
- several fixes related to printk continuation lines
- add support for HSV encoding formats
- lots of other cleanups, fixups and driver improvements.
* tag 'media/v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (496 commits)
[media] v4l: tvp5150: Add missing break in set control handler
[media] v4l: tvp5150: Don't inline the tvp5150_selmux() function
[media] v4l: tvp5150: Compile tvp5150_link_setup out if !CONFIG_MEDIA_CONTROLLER
[media] em28xx: don't store usb_device at struct em28xx
[media] em28xx: use usb_interface for dev_foo() calls
[media] em28xx: don't change the device's name
[media] mn88472: fix chip id check on probe
[media] mn88473: fix chip id check on probe
[media] lirc: fix error paths in lirc_cdev_add()
[media] s5p-mfc: Add support for MFC v8 available in Exynos 5433 SoCs
[media] s5p-mfc: Rework clock handling
[media] s5p-mfc: Don't keep clock prepared all the time
[media] s5p-mfc: Kill all IS_ERR_OR_NULL in clocks management code
[media] s5p-mfc: Remove dead conditional code
[media] s5p-mfc: Ensure that clock is disabled before turning power off
[media] s5p-mfc: Remove special clock rate management
[media] s5p-mfc: Use printk_ratelimited for reporting ioctl errors
[media] s5p-mfc: Set DMA_ATTR_ALLOC_SINGLE_PAGES
[media] vivid: Set color_enc on HSV formats
[media] v4l2-tpg: Init hv_enc field with a valid value
...
Now that we're storing usb_interface at em28xx struct,
there's no good reason to keep storing usb_device, as we can
get it from usb_interface. So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The usb_device->dev is not the right device for dev_foo() calls.
Instead, it should use usb_interface->dev.
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cec_allocate_adapter function doesn't need the parent device, only the
cec_register_adapter function needs it.
Drop the cec_devnode parent field, since devnode.dev.parent can be used
instead.
This change makes the framework consistent with other frameworks where the
parent device is not used until the device is registered.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A recent cleanup introduced a potential dereference of -EFAULT when we
call kfree(map->menu_info).
Fixes: 4cc5bed1ca ("[media] uvcvideo: Use memdup_user() rather than duplicating its implementation")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Those formats are implemented by The DFK 23UP1300, DFK 23UX249 and
DFK 23UX250 USB 3.0 industrial cameras from The Imaging Source.
Signed-off-by: Edgar Thier <info@edgarthier.net>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In randconfig builds that select VIDEO_EM28XX_V4L2 and
MEDIA_SUBDRV_AUTOSELECT, but not MEDIA_CAMERA_SUPPORT, we get
a Kconfig warning:
warning: (VIDEO_EM28XX_V4L2) selects VIDEO_MT9V011 which has unmet direct dependencies (MEDIA_SUPPORT && I2C && VIDEO_V4L2 && MEDIA_CAMERA_SUPPORT)
This avoids the warning by making that 'select' conditional on
MEDIA_CAMERA_SUPPORT. Alternatively we could mark EM28XX as
'depends on MEDIA_CAMERA_SUPPORT', but it does not seem to
have any real dependency on that itself.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If MEDIA_SUBDRV_AUTOSELECT and VIDEO_GO7007 are both set, we
automatically select VIDEO_OV7640, but that depends on MEDIA_CAMERA_SUPPORT,
so we get a Kconfig warning if that is disabled:
warning: (VIDEO_GO7007) selects VIDEO_OV7640 which has unmet direct dependencies (MEDIA_SUPPORT && I2C && VIDEO_V4L2 && MEDIA_CAMERA_SUPPORT)
This adds another dependency so we don't accidentally select
it when it is unavailable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We pass an int pointer to stk_camera_read_reg() but only write to the
highest byte. It's a bug on big endian systems and generally a nasty
thing to do and doesn't match the write function either.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
Remove another reduntdant include, that managed to sneak by commit
97139d4a6f ("treewide: remove redundant #include <linux/kconfig.h>").
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
'buf' is malloced in dibusb_rc_query() and should be freed before
leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: ff1c123545 ("[media] dibusb: handle error code on RC query")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It is not clear what this return value means. All implemenations
return 0, and the one caller ignores the value. Let's remove this
useless return value completely.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These are immutable. Making them "const" allows the compiler to move
them to the "rodata" section.
Note that cxd2841er_t_c_ops cannot be made "const", because
cxd2841er_attach() modifies it. Ouch!
[mchehab@s-opensource.com: fix merge conflicts]
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
-----BEGIN PGP SIGNATURE-----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=5WN9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.10 merge window
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
Instead of using pr_foo(), use dev_foo(), with provides a
better output. As this device is a multi-interface one,
we'll set the device name to show the chipset and the driver
used.
While here, get rid of printk continuation messages.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dvb-usb system has its own macro to print hexa dumps
(debug_dump). Such macro doesn't support messages with
KERN_CONT after commit 563873318d ("Merge branch 'printk-cleanups'").
So, let's get rid of a printk() that would be assuming that
this would work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some continuation messages are not using KERNEL_CONT.
Since commit 563873318d ("Merge branch 'printk-cleanups"),
this won't work as expected anymore. So, let's add KERN_CONT
to those lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some continuation messages are not using KERNEL_CONT.
Since commit 563873318d ("Merge branch 'printk-cleanups"),
this won't work as expected anymore. So, let's add KERN_CONT
to those lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Rift CV1 Sensor has bInterfaceClass set to vendor specific, so we
need an entry in uvc_ids to probe it. Just as the Rift DK2 IR tracker,
it misreports the pixel format as YUYV instead of Y8.
The sensor is configured with a low exposure time and high black level
by default, so that only bright IR sources can be seen.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that the CEC framework has been moved out of staging and into the
mainline kernel we can do the same for the pulse8-cec driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is a reworking of a patch originally submitted by Ryley Angus,
modified by Hans Verkuil and then seemingly forgotten before changes
suggested by Keith Pyle here:
http://www.mail-archive.com/linux-media@vger.kernel.org/msg75163.html
were made and tested.
I have implemented the suggested changes and have been testing for the
last 2 months. I am no longer experiencing lockups while recording
(with blue light on, requiring power cycling) which had been a long
standing problem with the HD-PVR. I have not noticed any other problems
since applying the patch.
Signed-off-by: Jonathan Sims <jonathan.625266@earthlink.net>
Reported-by: Ryley Angus <ryleyjangus@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As reported by smatch:
drivers/media/usb/usbtv/usbtv-video.c:716 usbtv_s_ctrl() error: doing dma on the stack (data)
drivers/media/usb/usbtv/usbtv-video.c:758 usbtv_s_ctrl() error: doing dma on the stack (data)
We should not do it, as it won't work on Kernels 4.9 and upper.
So, alloc a buffer for it.
Fixes: c53a846c48 ("[media] usbtv: add video controls")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The DVB binding schema at the DVB core assumes that the frontend is a
separate driver. Faling to do that causes OOPS when the module is
removed, as it tries to do a symbol_put_addr on an internal symbol,
causing craches like:
WARNING: CPU: 1 PID: 28102 at kernel/module.c:1108 module_put+0x57/0x70
Modules linked in: dvb_usb_gp8psk(-) dvb_usb dvb_core nvidia_drm(PO) nvidia_modeset(PO) snd_hda_codec_hdmi snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm snd_timer snd soundcore nvidia(PO) [last unloaded: rc_core]
CPU: 1 PID: 28102 Comm: rmmod Tainted: P WC O 4.8.4-build.1 #1
Hardware name: MSI MS-7309/MS-7309, BIOS V1.12 02/23/2009
Call Trace:
dump_stack+0x44/0x64
__warn+0xfa/0x120
module_put+0x57/0x70
module_put+0x57/0x70
warn_slowpath_null+0x23/0x30
module_put+0x57/0x70
gp8psk_fe_set_frontend+0x460/0x460 [dvb_usb_gp8psk]
symbol_put_addr+0x27/0x50
dvb_usb_adapter_frontend_exit+0x3a/0x70 [dvb_usb]
From Derek's tests:
"Attach bug is fixed, tuning works, module unloads without
crashing. Everything seems ok!"
Reported-by: Derek <user.vdr@gmail.com>
Tested-by: Derek <user.vdr@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit bc29131ecb10 ("[media] gp8psk: don't do DMA on stack") fixed the
usage of DMA on stack, but the memcpy was wrong for gp8psk_usb_in_op().
Fix it.
From Derek's email:
"Fix confirmed using 2 different Skywalker models with
HD mpeg4, SD mpeg2."
Suggested-by: Johannes Stezenbach <js@linuxtv.org>
Fixes: bc29131ecb10 ("[media] gp8psk: don't do DMA on stack")
Tested-by: Derek <user.vdr@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When receiving a nec repeat, ensure the correct scancode is repeated
rather than a random value from the stack. This removes the need for
the bogus uninitialized_var() and also fixes the warnings:
drivers/media/usb/dvb-usb/dib0700_core.c: In function ‘dib0700_rc_urb_completion’:
drivers/media/usb/dvb-usb/dib0700_core.c:679: warning: ‘protocol’ may be used uninitialized in this function
[sean addon: So after writing the patch and submitting it, I've bought the
hardware on ebay. Without this patch you get random scancodes
on nec repeats, which the patch indeed fixes.]
Signed-off-by: Sean Young <sean@mess.org>
Tested-by: Sean Young <sean@mess.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=MRLH
-----END PGP SIGNATURE-----
Merge tag 'media/v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A series of fixup patches meant to fix the usage of DMA on stack, plus
one warning fixup"
* tag 'media/v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (32 commits)
[media] radio-bcm2048: don't ignore errors
[media] pctv452e: fix semicolon.cocci warnings
[media] flexcop-usb: don't use stack for DMA
[media] stk-webcam: don't use stack for DMA
[media] s2255drv: don't use stack for DMA
[media] cpia2_usb: don't use stack for DMA
[media] digitv: handle error code on RC query
[media] dw2102: return error if su3000_power_ctrl() fails
[media] nova-t-usb2: handle error code on RC query
[media] technisat-usb2: use DMA buffers for I2C transfers
[media] pctv452e: don't call BUG_ON() on non-fatal error
[media] pctv452e: don't do DMA on stack
[media] nova-t-usb2: don't do DMA on stack
[media] gp8psk: don't go past the buffer size
[media] gp8psk: don't do DMA on stack
[media] dtv5100: don't do DMA on stack
[media] dtt200u: handle USB control message errors
[media] dtt200u: don't do DMA on stack
[media] dtt200u-fe: handle errors on USB control messages
[media] dtt200u-fe: don't do DMA on stack
...
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: <linux-media@vger.kernel.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: <linux-media@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: <linux-media@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch derives from previous one(s) by CrazyCat. I used the commit adding rev.3 to mainline Linux kernel as an example, so credits go to its author(s).
The hardware seems to scan and tune OK.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
TechnoTrend TT-connect S2-4650 CI seems to be a variation of
the DVBSky S960CI device.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The variable name is always assigned to a literal string in the
proceeding switch statement, so it is never null and hence the
null check is redundant. Remove null the check.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Add a new USB ID for EVOLVEO XtraTV stick.
[mchehab@s-opensource.org: fix patch and make checkpatch happy]
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some devices have invalid baSourceID references, causing uvc_scan_chain()
to fail, but if we just take the entities we can find and put them
together in the most sensible chain we can think of, turns out they do
work anyway. Note: This heuristic assumes there is a single chain.
At the time of writing, devices known to have such a broken chain are
- Acer Integrated Camera (5986:055a)
- Realtek rtl157a7 (0bda:57a7)
Signed-off-by: Henrik Ingo <henrik.ingo@avoinelama.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Keeping Documentation/media/v4l-drivers/gspca-cardlist.rst in
sync with the gspca script requires a parser. Simplify the
commented line, to make the parser work better.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some continuation messages are not using KERN_CONT.
Since commit 563873318d ("Merge branch 'printk-cleanups"),
this won't work as expected anymore. So, let's add KERN_CONT
to those lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The dvb_filter.c can hardly be considered as part of the DVB
core. More than half of the code there is commented out by
av7110 and ttusb_dec.
On the latter, just two small helper functions and a struct
definition is used.
Being part of the core means that it would require an
amount of work to fix issues in it, like bad printk's
on it, and to document it on some future, like other kAPI
headers. It simply not worth the effort for something that
seems to be deprecated, as no new drivers use it.
So, move it out of the core, by moving it to pci/ttpci
directory, where av7110 driver is kept, and copy the two
routines used by ttyusb_dec directly into its code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are still several places with printk's called directly.
Convert them to pr_foo() macros, except for the debug printk's,
as those are enabled via modprobe vars.
While here, realign the pr_foo() arguments to match the
recommended CodingStyle.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver has a lot of printk continuation lines for
debugging purposes. Since commit 563873318d
("Merge branch 'printk-cleanups"), this won't work as expected
anymore. So, let's add KERN_CONT to those lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols checkpatch warnings, several strings
were broken into multiple lines. This is not considered
a good practice anymore, as it makes harder to grep for
strings at the source code. So, join those continuation
lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYAoDuAAoJEHm+PkMAQRiGUeEH/03/cUjHeY5aJkcJ0JeHkoU5
GR5nRGcjfFF6cGujw2cSXBf5NzZTcrvBBFSgGNJ/rqm4EeDBsmf6T8qSfEKky/SY
3CNWSzayFU8Na3C8Z/a/xPTPicneX9zVnAi8XMAKXwWPmu21JCLR/hkKaxQ29qGr
Nqe4kEdLEF80d5lFRfNjK3CX4bD6w6P7aTBaM6wuRe4u5AXKJlSF+j838o5+/tSQ
Q1V7fyXlX+kwNmH4gViim8im0PLm7/7Li8e24pL3cAR2G6DHrUzcsYYoRMHpk5bv
HdBeCgZL6TnIaJc0ui2FRqQsifaVfM5J+pK81wr/JhBP2hmuWIN7NMupfCYtCcM=
=Mown
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rc1' into patchwork
Linux 4.9-rc1
* tag 'v4.9-rc1': (13774 commits)
Linux 4.9-rc1
score: traps: Add missing include file to fix build error
fs/super.c: don't fool lockdep in freeze_super() and thaw_super() paths
fs/super.c: fix race between freeze_super() and thaw_super()
overlayfs: Fix setting IOP_XATTR flag
iov_iter: kernel-doc import_iovec() and rw_copy_check_uvector()
CIFS: Retrieve uid and gid from special sid if enabled
CIFS: Add new mount option to set owner uid and gid from special sids in acl
qedr: Add events support and register IB device
qedr: Add GSI support
qedr: Add LL2 RoCE interface
qedr: Add support for data path
qedr: Add support for memory registeration verbs
qedr: Add support for QP verbs
qedr: Add support for PD,PKEY and CQ verbs
qedr: Add support for user context verbs
qedr: Add support for RoCE HW init
qedr: Add RoCE driver framework
pkeys: Remove easily triggered WARN
MIPS: Wire up new pkey_{mprotect,alloc,free} syscalls
...
the return values for dvb_usb_generic_rw() and dvb_usb_generic_write()
should be checked, as otherwise the drivers won't be doing the right
thing in the case of errors.
So, add __must_check to both declarations.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
While here, remove a dead function calling usb_control_msg().
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There's no sense on decoding and generating a RC key code if
there was an error on the URB control message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There's no sense on decoding and generating a RC key code if
there was an error on the URB control message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
On this driver, most of the transfers are OK, but the I2C
one was using stack.
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are some conditions on this driver that are tested with
BUG_ON() with are not serious enough to hang a machine.
So, just return an error if this happens.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If something bad happens while an USB control message is
transfered, return an error code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If something goes wrong, return an error code, instead of
assuming that everything went fine.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There's no sense on decoding and generating a RC key code if
there was an error on the URB control message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Be sure that I2C reads won't use stack by passing
a pointer to the state buffer, that we know it was
allocated via kmalloc, instead of relying on the buffer
allocated by an I2C client.
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dib0700_ctrl_rd() takes a RX and a TX pointer. Be sure that
both will point to a memory allocated via kmalloc().
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of sending USB commands for every stats call, collect
them once, when status is updated. As the frontend kthread
will call it on every few seconds, the stats will still be
collected.
Besides reducing the amount of USB/I2C transfers, this also
warrants that all stats will be collected at the same time,
and makes easier to convert it to DVBv5 stats in the future.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There's no sense on decoding and generating a RC key code if
there was an error on the URB control message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Merge more updates from Andrew Morton:
- a few block updates that fell in my lap
- lib/ updates
- checkpatch
- autofs
- ipc
- a ton of misc other things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (100 commits)
mm: split gfp_mask and mapping flags into separate fields
fs: use mapping_set_error instead of opencoded set_bit
treewide: remove redundant #include <linux/kconfig.h>
hung_task: allow hung_task_panic when hung_task_warnings is 0
kthread: add kerneldoc for kthread_create()
kthread: better support freezable kthread workers
kthread: allow to modify delayed kthread work
kthread: allow to cancel kthread work
kthread: initial support for delayed kthread work
kthread: detect when a kthread work is used by more workers
kthread: add kthread_destroy_worker()
kthread: add kthread_create_worker*()
kthread: allow to call __kthread_create_on_node() with va_list args
kthread/smpboot: do not park in kthread_create_on_cpu()
kthread: kthread worker API cleanup
kthread: rename probe_kthread_data() to kthread_probe_data()
scripts/tags.sh: enable code completion in VIM
mm: kmemleak: avoid using __va() on addresses that don't have a lowmem mapping
kdump, vmcoreinfo: report memory sections virtual addresses
ipc/sem.c: add cond_resched in exit_sme
...
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes this smatch warning:
drivers/media/usb/ttusb-dec/ttusb_dec.c:243 ttusb_dec_handle_irq() error: buffer overflow 'rc_keys' 26 <= 126
As the RC keys should be enabled previously, via:
set_bit(rc_keys[i], input_dev->keybit);
It wouldn't go past the buffer in practice. Yet, as bad
things may happen when going past buffer, it doesn't hurt adding
a check here.
While here, fix CodingStyle issues on the routine.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
cx231xx does not yet support attaching new-style i2c_client DVB demod
drivers. Add necessary code base on tuner support for i2c_client.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Tha ARM randconfig builds came up with another rare build failure
for the dib3000mc driver, when dvb-usb-dibusb-mb is built-in and
dib3000mc is a loadable module:
ERROR: "dibusb_dib3000mc_frontend_attach" [drivers/media/usb/dvb-usb/dvb-usb-nova-t-usb2.ko] undefined!
ERROR: "dibusb_dib3000mc_tuner_attach" [drivers/media/usb/dvb-usb/dvb-usb-nova-t-usb2.ko] undefined!
Apparently this used to be a valid configuration (build-time, not
run-time), but broke as part of a cleanup.
I tried reverting the cleanup, but saw that the code was still wrong
then. This version adds a dependency for dib3000mb, to ensure that
dib3000mb does not force the dibusb_dib3000mc_frontend_attach function
to be built-in when dib3000mc is a loadable module.
I have also checked the two other files that were changed in the original
cleanup, and found them to be correct in either version, so I do not
touch that part.
As this is a rather obscure bug, there is no need for backports.
Fixes: 028c70ff42 ("[media] dvb-usb/dvb-usb-v2: use IS_ENABLED")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Tha ARM randconfig builds came up with another rare build failure
for the dib3000mc driver, when dvb-usb-dibusb-mb is built-in and
dib3000mc is a loadable module:
ERROR: "dibusb_dib3000mc_frontend_attach" [drivers/media/usb/dvb-usb/dvb-usb-nova-t-usb2.ko] undefined!
ERROR: "dibusb_dib3000mc_tuner_attach" [drivers/media/usb/dvb-usb/dvb-usb-nova-t-usb2.ko] undefined!
Apparently this used to be a valid configuration (build-time, not
run-time), but broke as part of a cleanup.
I tried reverting the cleanup, but saw that the code was still wrong
then. This tries to fix the code properly, by moving the problematic
functions into a new file that now is built as a loadable module or
built-in, whichever is correct for a particular configuration. It fixes
the regression as well as the runtime problem that already existed.
The new module dependency chain is now:
dvb-usb-{dibusb_mc,a800,dib0700,umt-010,gp8psk} dvb-usb-dibusb-mb
| | | |
dvb-usb-dibusb-mc-common | ___________| |
| | | | |
dib3000mc (frontend) | | | dib3000mb (frontend)
| | |
| | |
dvb-usb-dibusb-common
I have also checked the two other files that were changed in the original
cleanup, and found them to be correct in either version, so I do not
touch that part.
As this is a rather obscure bug, there is no need for backports.
Fixes: 028c70ff42 ("[media] dvb-usb/dvb-usb-v2: use IS_ENABLED")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently we do not know what variant (bit length) of the nec protocol
is used, other than from guessing from the length of the scancode. Now
nec will be handled the same way as the sony protocol or the rc6 protocol;
one variant per bit length.
In the future we might want to expose the rc protocol type to userspace
and we don't want to be introducing this world of pain into userspace
too.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The hardware does not decode the 16, 20 or 24 bit variety.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These structures are only used to copy into other structures, so declare
them as const.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct dvb_tuner_ops i@p = { ... };
@ok1@
identifier r.i;
expression e;
position p;
@@
e = i@p
@ok2@
identifier r.i;
expression e1, e2;
position p;
@@
memcpy(e1, &i@p, e2)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct dvb_tuner_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct dvb_tuner_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These i2c_algorithm structures are only stored in the alg field of an
i2c_adapter structure, which is declared as const. This declare the
structures as const as well.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.alg = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for snd_pcm_ops structures that are only stored in the ops field of a
snd_soc_platform_driver structure or passed as the third argument to
snd_pcm_set_ops. The corresponding field or parameter is declared const,
so snd_pcm_ops structures that have this property can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_pcm_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_platform_driver e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i;
expression e1, e2;
position p;
@@
snd_pcm_set_ops(e1, e2, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_pcm_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_pcm_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver should not ignore errors while registering the I2C
bus, as this device can't even minimally work without the buses,
as it uses those buses internally to talk with the several IP
blocks inside the chip.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cx231xx_get_i2c_adap() function should return the I2C
adapter that will be used to talk with a device. It should never
be NULL, as otherwise the driver will try to dereference a
null pointer.
We might instead fix the callers, but if this condition
ever happens, it is really a driver bug, because i2c_port
should always be a value from enum CX231XX_I2C_MASTER_PORT.
Found when checking the code due to this bug:
[ 39.769021] BUG: unable to handle kernel NULL pointer dereference at 0000000000000002
[ 39.769105] IP: [<ffffffff81638393>] i2c_master_send+0x13/0x70
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The number of the cx231xx REQ for GPIO register set/get are wrong.
They should follow what's there at cx231xx-pcb-cfg.h.
Noticed while checking the cx231xx parser at the v4l-utils.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If something bad happens when switching between digital
and analog mode, prints an error and outputs the returned code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This device uses GPIOs: 28 to switch between analog and
digital modes: on digital mode, it should be set to 1.
The code that sets it on analog mode is OK, but it misses
the logic that sets it on digital mode.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cx231xx_set_agc_analog_digital_mux_select() callers
expect it to return 0 or an error. Returning a positive value
makes the first attempt to switch between analog/digital to fail.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
changed 'unsigned' to 'unsigned int' to obtain the coding style.
Signed-off-by: Jannik Becher <Becher.Jannik@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is part of a final push to convert all drivers to g/s_selection.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_thread" is involved in streaming the camera data.
It has a single work item(&dev->work_struct) and hence doesn't require
ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in sd_stop0() to ensure that there are no
pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Frank Zago <frank@zago.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_thread" is involved in streaming the camera data.
It has a single work item(&sd->work_struct) and hence doesn't require
ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in sd_stop0() to ensure that there are no
pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_thread" is involved in streaming the camera data.
It has a single work item(&sd->work_struct) and hence doesn't require
ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in sd_stop0() to ensure that there are no
pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_thread" is involved in updating the JPEG quality
of the gspca_dev. It has a single work item(&sd->work) and hence doesn't
require ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in sd_stop0() to ensure that there are no
pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "workqueue" is involved in polling the pvrusb2 hardware
(pvr2_hdw).
It has a single work item(&hdw->workpoll) and hence doesn't require
ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in pvr2_hdw_destroy to ensure that there are no
pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sometimes, the USB pipe could enter into a stalled state,
and may need a reset to rework.
Add such logic.
[mchehab@osg.samsung.com: ported from Android's source:
3a322adc00%5E%21]
Signed-off-by: Terry Heo <terryheo@google.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mrOW
-----END PGP SIGNATURE-----
Merge tag 'media/v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new framework support for HDMI CEC and remote control support
- new encoding codec driver for Mediatek SoC
- new frontend driver: helene tuner
- added support for NetUp almost universal devices, with supports
DVB-C/S/S2/T/T2 and ISDB-T
- the mn88472 frontend driver got promoted from staging
- a new driver for RCar video input
- some soc_camera legacy drivers got removed: timb, omap1, mx2, mx3
- lots of driver cleanups, improvements and fixups
* tag 'media/v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (377 commits)
[media] cec: always check all_device_types and features
[media] cec: poll should check if there is room in the tx queue
[media] vivid: support monitor all mode
[media] cec: fix test for unconfigured adapter in main message loop
[media] cec: limit the size of the transmit queue
[media] cec: zero unused msg part after msg->len
[media] cec: don't set fh to NULL in CEC_TRANSMIT
[media] cec: clear all status fields before transmit and always fill in sequence
[media] cec: CEC_RECEIVE overwrote the timeout field
[media] cxd2841er: Reading SNR for DVB-C added
[media] cxd2841er: Reading BER and UCB for DVB-C added
[media] cxd2841er: fix switch-case for DVB-C
[media] cxd2841er: fix signal strength scale for ISDB-T
[media] cxd2841er: adjust the dB scale for DVB-C
[media] cxd2841er: provide signal strength for DVB-C
[media] cxd2841er: fix BER report via DVBv5 stats API
[media] mb86a20s: apply mask to val after checking for read failure
[media] airspy: fix error logic during device register
[media] s5p-cec/TODO: add TODO item
[media] cec/TODO: drop comment about sphinx documentation
...
Fix a memory leak on probe error of the airspy usb device driver.
The problem is triggered when more than 64 usb devices register with
v4l2 of type VFL_TYPE_SDR or VFL_TYPE_SUBDEV.
The memory leak is caused by the probe function of the airspy driver
mishandeling errors and not freeing the corresponding control structures
when an error occours registering the device to v4l2 core.
A badusb device can emulate 64 of these devices, and then through
continual emulated connect/disconnect of the 65th device, cause the
kernel to run out of RAM and crash the kernel, thus causing a local DOS
vulnerability.
Fixes CVE-2016-5400
Signed-off-by: James Patrick-Evans <james@jmp-e.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch addresses CVE-2016-5400, a local DOS vulnerability caused by
a memory leak in the airspy usb device driver.
The vulnerability is triggered when more than 64 usb devices register
with v4l2 of type VFL_TYPE_SDR or VFL_TYPE_SUBDEV.A badusb device can
emulate 64 of these devices then through continual emulated
connect/disconnect of the 65th device, cause the kernel to run out of
RAM and crash the kernel.
The vulnerability exists in kernel versions from 3.17 to current 4.7.
The memory leak is caused by the probe function of the airspy driver
mishandeling errors and not freeing the corresponding control structures
when an error occours registering the device to v4l2 core.
Signed-off-by: James Patrick-Evans <james@jmp-e.com>
Cc: stable@vger.kernel.org # Up to Kernel 3.17
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The value 5 of the EEPROM_TS_MODE register (meaning dual tuner presence) is
only valid for AF9035 devices. For IT9135 devices it is invalid and led to a
false positive dual tuner mode detection with PCTV 79e.
Therefore on non-AF9035 devices and with value 5 the driver now defaults to
single tuner mode and outputs a regarding info message to log.
This fixes Bugzilla bug #118561.
Reported-by: Marc Duponcheel <marc@offline.be>
Signed-off-by: Stefan Pöschel <basic.master@gmx.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
My static checker complains that if adap->props.num_frontends is 0 then
"ret" is uninitialized. I don't think that can happen. But "ret" is
always zero here so we can just remove the condition.
This extra check was added in commit 0d3ab8410d ('[media] dvb core:
must check dvb_create_media_graph()').
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the USB ID for Terratec Cinergy S2 Rev.3 (0ccd:0102).
Curiously dvb-usb-ids included already the USB ID for TERRATEC_CINERGY_S2_R3 even if the device was not supported.
Reported-by: Christian Knippel <namerp@googlemail.com>
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The DW2102 DVB-S/S2 driver uses the info() logging function from
dvb-usb.h. This function already appends a newline to the provided log
message, causing the dmesg output from DW2102 to include blank lines.
Fix this by removing the newline in the calls to info().
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When disconnecting the usbtv device, the sound card is unregistered
from ALSA and the snd member of the usbtv struct is set to NULL. If
the usbtv snd_trigger work is running, this can cause a race condition
where the kernel will attempt to access free'd resources, shown in
[1].
This patch fixes the disconnection code by cancelling any snd_trigger
work before unregistering the sound card from ALSA and checking that
the snd member still exists in the work function.
[1]:
usb 3-1.2: USB disconnect, device number 6
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffff81093850>] process_one_work+0x30/0x480
PGD 405bbf067 PUD 405bbe067 PMD 0
Call Trace:
[<ffffffff81093ce8>] worker_thread+0x48/0x4e0
[<ffffffff81093ca0>] ? process_one_work+0x480/0x480
[<ffffffff81093ca0>] ? process_one_work+0x480/0x480
[<ffffffff81099998>] kthread+0xd8/0xf0
[<ffffffff815c73c2>] ret_from_fork+0x22/0x40
[<ffffffff810998c0>] ? kthread_worker_fn+0x170/0x170
---[ end trace 0f3dac5c1a38e610 ]---
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Tested-by: Peter Sutton <foxxy@foxdogstudios.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This op is deprecated and should not be used anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This op is deprecated and should not be used anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This op is deprecated and should not be used anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Converts the dtt200u DVB USB driver over to the rc-core
infrastructure for its handling of IR remotes. This device can receive
generic NEC / NEC Extended signals and the switch to the newer core
enables the easy use of tools such as ir-keytable to modify the active
key map.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_thread" is involved in updating parameters for
transfers. It has a single work item(&sd->work) and hence
doesn't require ordering. Also, it is not being used on a memory
reclaim path. Hence, the singlethreaded workqueue has been replaced with
the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in sd_stop0() to ensure that there are no
pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXefulAAoJEHm+PkMAQRiG6nMH/2O1vcZeOtqmx2yCMUeXyKAT
wG88XflXzf3rM7C7TiObEYVf/bbLleJ7saDLEeic7ButD5gyYacIuzylVnrcqfBc
vinz4cOw5kvu9DrRkCKdOfiTAgwYtqQW+syJ8ZK4lPQuSxnPAs+F/FKSOpyUF5FN
Dngr520KjYKBEtn27W9UDPChFRwQoWAlaOC534eusaArCJtHGHHiuq5TEDn2EIo8
pUw2vwx5JiquSHOY34WLU7r+QoilovCQlUSsBQdLlPjfMB1QFtclPYa+5yEMjkT4
wusOUOfS/zK0rV6KnEdc/SkpiVX5C9WpFiWUOdEeJ5mZ+KijVkaOa9K1EDx8jSM=
=7Hwh
-----END PGP SIGNATURE-----
Merge tag 'v4.7-rc6' into patchwork
Linux 4.7-rc6
* tag 'v4.7-rc6': (1245 commits)
Linux 4.7-rc6
ovl: warn instead of error if d_type is not supported
MIPS: Fix possible corruption of cache mode by mprotect.
locks: use file_inode()
usb: dwc3: st: Use explicit reset_control_get_exclusive() API
phy: phy-stih407-usb: Use explicit reset_control_get_exclusive() API
phy: miphy28lp: Inform the reset framework that our reset line may be shared
namespace: update event counter when umounting a deleted dentry
9p: use file_dentry()
lockd: unregister notifier blocks if the service fails to come up completely
ACPI,PCI,IRQ: correct operator precedence
fuse: serialize dirops by default
drm/i915: Fix missing unlock on error in i915_ppgtt_info()
powerpc: Initialise pci_io_base as early as possible
mfd: da9053: Fix compiler warning message for uninitialised variable
mfd: max77620: Fix FPS switch statements
phy: phy-stih407-usb: Inform the reset framework that our reset line may be shared
usb: dwc3: st: Inform the reset framework that our reset line may be shared
usb: host: ehci-st: Inform the reset framework that our reset line may be shared
usb: host: ohci-st: Inform the reset framework that our reset line may be shared
...
Patrick Keshishian improved the explanation of the protocol when porting
the driver to OpenBSD. Given it's a reverse engineering one and there's
no documetnation it might be helpful to whoever hacks on the driver.
Signed-off-by: Patrick Keshishian <sidster@boxsoft.com>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
OpenBSD would like to reuse some code but consider the licensing not
clear enough. Let's clarify it a bit so that it suits their conventions:
1.) Keep the "extra text" away from the copyright statement and the
rights grant.
2.) Add the warranty disclaimer -- it should not be legally required,
nevertheless the clause 1. of the rights grant refest to it.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Federico Simoncelli <fsimonce@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When CONFIG_INPUT is disabled, multiple gspca backend drivers
print compile-time warnings about unused variables:
media/usb/gspca/cpia1.c: In function 'sd_stopN':
media/usb/gspca/cpia1.c:1627:13: error: unused variable 'sd' [-Werror=unused-variable]
media/usb/gspca/konica.c: In function 'sd_stopN':
media/usb/gspca/konica.c:246:13: error: unused variable 'sd' [-Werror=unused-variable]
This annotates the variables as __maybe_unused, to let the compiler
know that they are declared intentionally.
Fixes: ee186fd96a ("[media] gscpa_t613: Add support for the camera button")
Fixes: c2f644aeeb ("[media] gspca_cpia1: Add support for button")
Fixes: b517af7228 ("V4L/DVB: gspca_konica: New gspca subdriver for konica chipset using cams")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "workqueue" is involved in transmitting hdpvr buffers.
It has a single work item(&dev->worker) and hence doesn't require
ordering. Also, it is not being used on a memory reclaim path. Hence,
the singlethreaded workqueue has been replaced with the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in hdpvr_device_release() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_thread" is involved in JPEG quality update.
It has a single work item(&sd->work) and hence doesn't require ordering.
Also, it is not being used on a memory reclaim path. Hence, the
singlethreaded workqueue has been replaced with the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in sd_stop0() to ensure that there are no
pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2-compliance fails with this message:
fail: v4l2-test-buffers.cpp(250): \
timestamp != V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC && \
timestamp != V4L2_BUF_FLAG_TIMESTAMP_COPY
...
test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: FAIL
When setting the frame time, gspca uses v4l2_get_timestamp() which uses
ktime_get_ts() which uses ktime_get_ts64() which returns a monotonic
timestamp, so it's safe to initialize the buffer flags to
V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC to fix the failure.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to v4l2-compliance VIDIOC_ENUM_FRAMEINTERVALS should fail for
unsupported frame sizes, but gspca is too tolerant and tries to find
the frame intervals for the frame size nearest to the requested one.
This makes v4l2-compliance fail with this message:
fail: v4l2-test-formats.cpp(123): \
found frame intervals for invalid size 321x240
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: FAIL
Fix this by using an exact match for the frame size when enumerating
frame intervals, and retuning an error if the frame size for which the
frame intervals have been asked is not supported.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The name wxh_to_nearest_mode() reflects better what the function does.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set the frame _interval_ type to V4L2_FRMIVAL_TYPE_DISCRETE instead of
using V4L2_FRMSIZE_TYPE_DISCRETE which is meant for frame _size_.
The old and new values happen to be the same so there is no functional
change.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When writing the change in commit dcc7fdbec5 ("[media] gspca:
ov534/topro: prevent a division by 0") I used magic numbers for the
default framerate to minimize the code footprint to make it easier to
backport the patch to the stable trees.
However it's better if the default framerate has its own define to avoid
risking using different values in different places, and for readability.
While at it also remove some trivial comments about the framerates which
don't add much to the code anymore.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The pwc driver causes a warning when CONFIG_USB_PWC_INPUT_EVDEV is unset:
drivers/media/usb/pwc/pwc-if.c: In function 'usb_pwc_probe':
drivers/media/usb/pwc/pwc-if.c:1115:1: warning: label 'err_video_unreg' defined but not used [-Wunused-label]
This moves the unused label and code inside another #ifdef to
get rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this a proper typed array. Drop the old allocate context code since
that is no longer used.
Note that the memops functions now get a struct device pointer instead of
the struct device ** that was there initially (actually a void pointer to
a struct containing only a struct device pointer).
This code is now a lot cleaner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If *nplanes is not zero, it should use the requested size if valid
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Gcc 6.1 warns about an unused table:
drivers/media/usb/em28xx/em28xx-dvb.c:907:38: warning: 'pctv_461e_m88ds3103_config' defined but not used [-Wunused-const-variable=]
static const struct m88ds3103_config pctv_461e_m88ds3103_config = {
^~~~~~~~~~~~~~~~~~~~~~~~~~
That's a left over of patch 76b91be3d3 ('em28xx: PCTV 461e use I2C
client for demod and SEC').
Remove the dead code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The header file has some private static structures that
are used only by the C file. Move those structures to the C file,
in order to shut up gcc 6.1 warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The header file has some private static structures that
are used only by the C file. Move those structures to the C file,
in order to shut up gcc 6.1 warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The header file has some private static structures that
are used only by the C file. Move those structures to the C file,
in order to shut up gcc 6.1 warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The header file has some private static structures that
are used only by the C file. Move those structures to the C file,
in order to shut up gcc 6.1 warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The header file has some private static structures that
are used only by the C file. Move those structures to the C file,
in order to shut up gcc 6.1 warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The mc5602_s5k4aa.h has some private static structures that
are used only by the C file. Move those structures to the C file,
in order to shut up gcc 6.1 warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The mc5602_brigde.h is included at m5602 submodules. This
causes Gcc 6.1 to complain:
drivers/media/usb/gspca/m5602/m5602_bridge.h:124:28: warning: 'sensor_urb_skeleton' defined but not used [-Wunused-const-variable=]
static const unsigned char sensor_urb_skeleton[] = {
^~~~~~~~~~~~~~~~~~~
drivers/media/usb/gspca/m5602/m5602_bridge.h:119:28: warning: 'bridge_urb_skeleton' defined but not used [-Wunused-const-variable=]
static const unsigned char bridge_urb_skeleton[] = {
^~~~~~~~~~~~~~~~~~~
Let's shut up gcc 6.1 warnings by moving those data structures
to the core, as they're used only there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Gcc 6.1 warns about some unused vars. Remove them:
drivers/media/usb/usbvision/usbvision-core.c:94:18: warning: 'min_imgheight' defined but not used [-Wunused-const-variable=]
static const int min_imgheight = MIN_FRAME_HEIGHT;
^~~~~~~~~~~~~
drivers/media/usb/usbvision/usbvision-core.c:93:18: warning: 'min_imgwidth' defined but not used [-Wunused-const-variable=]
static const int min_imgwidth = MIN_FRAME_WIDTH;
^~~~~~~~~~~~
drivers/media/usb/usbvision/usbvision-core.c:92:18: warning: 'max_imgheight' defined but not used [-Wunused-const-variable=]
static const int max_imgheight = MAX_FRAME_HEIGHT;
^~~~~~~~~~~~~
drivers/media/usb/usbvision/usbvision-core.c:91:18: warning: 'max_imgwidth' defined but not used [-Wunused-const-variable=]
static const int max_imgwidth = MAX_FRAME_WIDTH;
^~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
struct media_devnode is currently embedded at struct media_device.
While this works fine during normal usage, it leads to a race
condition during devnode unregister. the problem is that drivers
assume that, after calling media_device_unregister(), the struct
that contains media_device can be freed. This is not true, as it
can't be freed until userspace closes all opened /dev/media devnodes.
In other words, if the media devnode is still open, and media_device
gets freed, any call to an ioctl will make the core to try to access
struct media_device, with will cause an use-after-free and even GPF.
Fix this by dynamically allocating the struct media_devnode and only
freeing it when it is safe.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The uvc compat ioctl implementation seems to have copied user data
for no good reason. Remove a bunch of copies.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
The current code goes through a lot of indirection just to call a
known handler. Simplify it: just call the handlers directly.
Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@kernel.org>
The code is checking for negative returns but it should be checking for
zero.
Fixes: aab3125c43 ('[media] em28xx: add support for registering multiple i2c buses')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove __func__ and KBUILD_MODNAME from logging formatters and pass
USB interface device instead, so logging can be done correctly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
