The macro BADBLOCK_MARKER_LENGTH is pretty long and could be reduced to
BBM_LEN which is more handy to use in the code.
This is a purely cosmetic change and is only done to avoid further
change to contain 100+ char lines just because of this definition.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610134906.3503303-3-miquel.raynal@bootlin.com
This hardware controller is embedded in XilinX Zynq-7000 SoCs and has
partial support for Hamming ECC correction.
This work is inspired from the original contributions of Punnaiah
Choudary Kalluri and Naga Sureshkumar Relli.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Michael Walle <michael@walle.cc> [on zynq-7000]
Link: https://lore.kernel.org/linux-mtd/20210610082040.2075611-19-miquel.raynal@bootlin.com
After power up, all SPI NAND's blocks are locked. Only read operations
are allowed, write and erase operations are forbidden.
The SPI NAND framework unlocks all the blocks during its initialization.
During a standby low power, the memory is powered down, losing its
configuration.
During the resume, the QSPI driver state is restored but the SPI NAND
framework does not reconfigured the memory.
This patch adds SPI-NAND MTD PM handlers for resume ops.
SPI NAND resume op re-initializes SPI NAND flash to its probed state.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210602094913.26472-4-patrice.chotard@foss.st.com
There are 2 timing registers:
- "data interface"
- "timings"
So far, the "data interface" register was named "timings" which begins
misleading when bringing support for the "timings" register. Rename it
to "data_iface".
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210527084959.208804-1-miquel.raynal@bootlin.com
Without the use of le16_to_cpu(), these accesses would have been wrong
on a big-endian machine.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 45606518f9 ("mtd: rawnand: Add onfi_fill_nvddr_interface_config() helper")
Fixes: 9310668fb6 ("mtd: rawnand: Retrieve NV-DDR timing modes from the ONFI parameter page")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210527084913.208635-1-miquel.raynal@bootlin.com
Xilinx ZynqMP SoC and the Arasan controller support 64-bit DMA
addressing. Define the right mask otherwise the default is 32
and some accesses may overflow the default mask.
Reported-by: Jorge Courett <jorge.courett@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Jorge Courett <jorge.courett@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20210527084548.208429-1-miquel.raynal@bootlin.com
In the raw NAND world, ECC engines increment ecc_stats and the final
caller is responsible for returning -EBADMSG if the verification
failed.
In the SPI-NAND world it was a bit different until now because there was
only one possible ECC engine: the on-die one. Indeed, the
spinand_mtd_read() call was incrementing the ecc_stats counters
depending on the outcome of spinand_check_ecc_status() directly.
So now let's split the logic like this:
- spinand_check_ecc_status() is specific to the SPI-NAND on-die engine
and is kept very simple: it just returns the ECC status (bonus point:
the content of this helper can be overloaded).
- spinand_ondie_ecc_finish_io_req() is the caller of
spinand_check_ecc_status() and will increment the counters and
eventually return -EBADMSG.
- spinand_mtd_read() is not tied to the on-die ECC implementation and
should be able to handle results coming from other ECC engines: it has
the responsibility of returning the maximum number of bitflips which
happened during the entire operation as this is the only helper that
is aware that several pages may be read in a row.
Fixes: 945845b54c ("mtd: spinand: Instantiate a SPI-NAND on-die ECC engine")
Reported-by: YouChing Lin <ycllin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: YouChing Lin <ycllin@mxic.com.tw>
Link: https://lore.kernel.org/linux-mtd/20210527084345.208215-1-miquel.raynal@bootlin.com
The result of an expression consisting of a single relational operator is
already of the bool type and does not need to be evaluated explicitly.
No functional change.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210510114944.3527-1-thunder.leizhen@huawei.com
Make use of the cs-gpios DT property as well as the core helper to parse
it so that the Arasan controller driver can now assert many more chips
than natively.
The Arasan controller has an internal limitation: RB0 is tied to CS0 and
RB1 is tied to CS1. Hence, it is possible to use external GPIOs as long
as one or the other native CS is not used (or configured to be driven as
a GPIO) and that all additional CS are physically wired on its
corresponding RB line. Eg. CS0 is used as a native CS, CS1 is not used
as native CS and may be used as a GPIO CS, CS2 is an additional GPIO
CS. Then the target asserted by CS0 should also be wired to RB0, while
the targets asserted by CS1 and CS2 should be wired to RB1.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-5-miquel.raynal@bootlin.com
The controller being always asserting one CS or the other, there is no
need to actually select the right target before doing a page read/write.
However, the anfc_select_target() helper actually also changes the
timing configuration and clock in the case were two different NAND chips
with different timing requirements would be used. In this situation, we
must ensure proper configuration of the controller by calling it.
As a consequence of this change, the anfc_select_target() helper is
being moved earlier in the driver.
Fixes: 88ffef1b65 ("mtd: rawnand: arasan: Support the hardware BCH ECC engine")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-4-miquel.raynal@bootlin.com
New chips may feature a lot of CS because of their extended length. As
many controllers have been designed a decade ago, they usually only
feature just a couple. This does not mean that the entire range of
these chips cannot be accessed: it is just a matter of adding more
GPIO CS in the hardware design. A DT property has been added to
describe the CS array: cs-gpios.
Here is the code parsing it this new property, allocating what needs to
be, requesting the GPIOs and returning an array with the additional
available CS. The first entries of this array are left empty and are
reserved for native CS.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-3-miquel.raynal@bootlin.com
As explained in the comment introduced above the fix, the Arasan
controller driver starts an operation when the prog register is being
written with a "type" specific to the action to perform.
The prog type used until now to perform a CHANGE READ COLUMN with an SDR
interface was the PAGE READ type (CMD + ADDR + CMD +
DATA). Unfortunately, for an unknown reason (let's call this a silicon
bug) any CHANGE READ COLUMN performed this way in NV-DDR mode will fail:
the data ready flag will never be triggered, nor will be the transfer
complete flag. Forcefully, this leads to a timeout situation which is
not easy to handle.
Fortunately, it was spotted that sending the same commands through a
different prog register "type", CHANGE READ COLUMN ENHANCED, would work
all the time (even though this particular command is not supported by
the core and is only available in a limited set of devices - we only
care about the controller configuration and not the actual command which
is sent to the device). So let's use this type instead when a CHANGE
READ COLUMN is requested.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-22-miquel.raynal@bootlin.com
Now that the necessary peaces to support the NV-DDR interface type have
been contributed, let's add the relevant logic to make use of it. In
particular, the core does not choose the best SDR timings anymore but
calls a more generic helper instead.
This helper checks if NV-DDR is supported by trying to find the best
NV-DDR supported mode through a logic very close to what is being done
for SDR timings. If no NV-DDR mode in common between the NAND controller
and the NAND chip is found, the core will fallback to SDR.
Side note: theoretically, the data clock speed in NV-DDR mode 0 is
slower than in SDR mode 5. In the situation where we would get a working
NV-DDR mode 0, we could also try if SDR mode 5 is supported and
eventually fallback to it in order to get the fastest possible
throughput. However, in the field, it looks like most of the devices
supporting NV-DDR avoid implementing the fastest SDR modes (like 4 and 5
EDO modes, which are a bit more complicated to handle than the other SDR
modes). So, we will stick to the simplest logic: try NV-DDR otherwise
fallback to SDR. If someone else experiences strong differences because
of that we may still implement the logic defined above.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-19-miquel.raynal@bootlin.com
Until now the parameter of the ADDR_TIMING_MODE feature was just the
ONFI timing mode (from 0 to 5) because we were only supporting the SDR
data interface. In the same byte, bits 4 and 5 indicate which data
interface is being configured so use them to set the right mode and also
read them back to ensure the right timing has been setup on the chip's
side.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-17-miquel.raynal@bootlin.com
Introduce a similar helper to onfi_find_closest_sdr_mode(), but for
NV-DDR timings. It just takes a timing structure as parameter and
returns the closest mode by comparing all minimum timings. This is
useful for rigid controllers on which tuning the timings is not
possible.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-16-miquel.raynal@bootlin.com
As explained in chapter "NV-DDR / NV-DDR2 / NV-DDR3 and Repeat Bytes" of
the ONFI specification, with some commands (mainly the commands which do
not transfer actual data) the data bytes are repeated twice and it is
the responsibility of the receiver to discard them properly. The
concerned commands are: SET_FEATURES, READ_ID, GET_FEATURES,
READ_STATUS, READ_STATUS_ENHANCED, ODT_CONFIGURE. Hence, in the NAND
core we are only impacted by the implementation of READ_ID, GET_FEATURES
and READ_STATUS.
The logic is the same for all:
2/ Check if it is relevant to read all data bytes twice.
1/ Allocate a buffer with twice the requested size (may be done
statically).
2/ Update the instruction structure to read these extra bytes in the
allocated buffer.
3/ Copy the even bytes into the original buffer. The performance hit is
negligible on such small data transfers anyway and we don't really
care about performances at this stage anyway.
4/ Free the allocated buffer, if any.
Note: nand_data_read_op() is also impacted because it is theoretically
possible to run the command/address cycles first, and, as another
operation, do the data transfers. In this case we can easily identify
the impacted commands because the force_8bit flag will be set (due to
the same reason: their data does not go through the same pipeline).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-15-miquel.raynal@bootlin.com
Most timings related to the bus timings are different between SDR and
NV-DDR. However, we identified 9 individual timings which are more
related to the NAND chip internals. These are common between the two
interface types. Fortunately, only these common timings are being shared
through the NAND core and its ->exec_op() interface, which allows the
writing of a simple macro checking the interface type and depending on
it, returning either the relevant SDR timing or the NV-DDR timing. This
is the purpose of the NAND_COMMON_TIMING_PS() macro.
As all this is evaluated at build time, one will immediately be notified
in case a non common timing is being accessed through this macro.
Two handy macros are also inserted at the same time, which use
PSEC_TO_NSEC or PSEC_TO_MSEC so that it is very easy to return timings
in milli-, nano- or pico-seconds, as usually requested by the internal
API.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-14-miquel.raynal@bootlin.com
Legacy code should not benefit from newer features, especially in
helpers that have been deprecated for a very long time. People who want
NV-DDR support must migrate their driver to the ->exec_op() API.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-13-miquel.raynal@bootlin.com
Same logic as for the SDR path, let's create a
onfi_fill_nvddr_interface_config() helper to fill an interface
configuration structure with NV-DDR timings, given a specific ONFI mode.
There is one additional thing to do compared to SDR mode: tCAD timing
can be fast or slow and this depends on an ONFI parameter page bit. By
default the slow value is declared in the timings structure definition,
but this helper can shrink it down if necessary.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-12-miquel.raynal@bootlin.com
This helper actually fills the interface configuration with SDR data.
As part of the work to bring NV-DDR support, let's rename this helper
onfi_fill_sdr_interface_config() and add a generic indirection to it.
There are no functional changes here, but this will simplify a next
change which adds onfi_fill_nvddr_interface_config() support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-11-miquel.raynal@bootlin.com
When parsing the ONFI parameter page, save the available NV-DDR timing
modes in the core's dynamic ONFI structure. Once available to the rest
of the core out of the ONFI driver, these values will then be used to
derive the best timing mode.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-10-miquel.raynal@bootlin.com
In particular, first ONFI specifications referred to SDR modes as
asynchronous modes, which is not the term we usually have in mind. The
spec has then been updated, so do the same here in the NAND subsystem to
avoid any possible confusion.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-7-miquel.raynal@bootlin.com
In the unlikely event that both blocks 10 and 11 are marked as bad (on a
32 bit machine), then the process of marking block 10 as bad stomps on
cached entry for block 11. There are (of course) other examples.
Signed-off-by: Patrick Doyle <pdoyle@irobot.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Yoshio Furuyama <ytc-mb-yfuruyama7@kioxia.com>
[<miquel.raynal@bootlin.com>: Fixed the title]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/774a92693f311e7de01e5935e720a179fb1b2468.1616635406.git.ytc-mb-yfuruyama7@kioxia.com
Commit 82bfd11f1b ("mtd: rawnand: qcom: Add support for Qcom SMEM
parser") made qcomsmem the only parser for qcom_nandc partitions. This
might be problematic for systems with both SPI and NAND MTD devices.
When booting from SPI flash the partition table should not apply to the
NAND flash.
Prepend cmdlinepart and ofpart parsers to allow override of the
partition parser.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/cf470f05af514acd5bd94548804ffa96b966a0a8.1619029869.git.baruch@tkos.co.il
Smatch complains that the error code is not set on this error path:
drivers/mtd/nand/raw/nand_base.c:842 nand_setup_interface()
warn: missing error code 'ret'
But actually returning success is intentional because the NAND chip will
still work in mode 0. This patch adds a "ret = 0;" assignment to make
the intent more clear and to silence the static checker warning. It
doesn't affect the compiled code because GCC optimises the assignment
away.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/YH6Ugwz3gcga+q8X@mwanda
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210408111514.1011020-2-yukuai3@huawei.com
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Li <liwei391@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210407100526.3278741-1-liwei391@huawei.com
JFFS2:
- Use splice_write()
- Fix for a slab-out-of-bounds bug
UBI:
- Fix for clang related warnings
- Code cleanup
UBIFS:
- Fix for inode rebirth at replay
- Set s_uuid
- Use zstd for default filesystem
-----BEGIN PGP SIGNATURE-----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=IwH7
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull JFFS2, UBI and UBIFS updates from Richard Weinberger:
"JFFS2:
- Use splice_write()
- Fix for a slab-out-of-bounds bug
UBI:
- Fix for clang related warnings
- Code cleanup
UBIFS:
- Fix for inode rebirth at replay
- Set s_uuid
- Use zstd for default filesystem"
* tag 'for-linus-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubi: Remove unnecessary struct declaration
jffs2: Hook up splice_write callback
jffs2: avoid Wempty-body warnings
jffs2: Fix kasan slab-out-of-bounds problem
ubi: Fix fall-through warnings for Clang
ubifs: Report max LEB count at mount time
ubifs: Set s_uuid in super block to support ima/evm uuid options
ubifs: Default to zstd compression
ubifs: Only check replay with inode type to judge if inode linked
-----BEGIN PGP SIGNATURE-----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=ovSn
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Stop synchronizing kernel log buffer readers by logbuf_lock. As a
result, the access to the buffer is fully lockless now.
Note that printk() itself still uses locks because it tries to flush
the messages to the console immediately. Also the per-CPU temporary
buffers are still there because they prevent infinite recursion and
serialize backtraces from NMI. All this is going to change in the
future.
- kmsg_dump API rework and cleanup as a side effect of the logbuf_lock
removal.
- Make bstr_printf() aware that %pf and %pF formats could deference the
given pointer.
- Show also page flags by %pGp format.
- Clarify the documentation for plain pointer printing.
- Do not show no_hash_pointers warning multiple times.
- Update Senozhatsky email address.
- Some clean up.
* tag 'printk-for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: (24 commits)
lib/vsprintf.c: remove leftover 'f' and 'F' cases from bstr_printf()
printk: clarify the documentation for plain pointer printing
kernel/printk.c: Fixed mundane typos
printk: rename vprintk_func to vprintk
vsprintf: dump full information of page flags in pGp
mm, slub: don't combine pr_err with INFO
mm, slub: use pGp to print page flags
MAINTAINERS: update Senozhatsky email address
lib/vsprintf: do not show no_hash_pointers message multiple times
printk: console: remove unnecessary safe buffer usage
printk: kmsg_dump: remove _nolock() variants
printk: remove logbuf_lock
printk: introduce a kmsg_dump iterator
printk: kmsg_dumper: remove @active field
printk: add syslog_lock
printk: use atomic64_t for devkmsg_user.seq
printk: use seqcount_latch for clear_seq
printk: introduce CONSOLE_LOG_MAX
printk: consolidate kmsg_dump_get_buffer/syslog_print_all code
printk: refactor kmsg_dump_get_buffer()
...
* Handle possible -EPROBE_DEFER from parse_mtd_partitions()
* Constify buf in mtd_write_user_prot_reg()
* Constify name param in mtd_bdi_init
* Fix fall-through warnings for Clang
* Get rid of Big MTD Lock ouf of mtdchar
* Drop mtd_mutex usage from mtdchar_open()
* Don't lock when recursively deleting partitions
* Use module_mtd_blktrans() to register driver when relevant
* Parse MTD as NVMEM cells
* New OTP (one-time-programmable) erase ioctl
* Require write permissions for locking and badblock ioctls
* physmap:
- Fix error return code of physmap_flash_remove()
- physmap-bt1-rom: Fix unintentional stack access
* ofpart parser:
- Support Linksys Northstar partitions
- Make symbol 'bcm4908_partitions_quirks' static
- Limit parsing of deprecated DT syntax
- Support BCM4908 fixed partitions
* Qcom parser:
- Incompatible with spi-nor 4k sectors
- Fix error condition
- Extend Qcom SMEM parser to SPI flash
CFI:
* Disable broken buffered writes for CFI chips within ID 0x2201
* Address a Coverity report for unused value
SPI NOR core:
* Add OTP support
* Fix module unload while an op in progress
* Add various cleanup patches
* Add Michael and Pratyush as designated reviewers in MAINTAINERS
SPI NOR controller drivers:
* intel-spi:
- Move platform data header to x86 subfolder
NAND core:
* Fix error handling in nand_prog_page_op() (x2)
* Add a helper to retrieve the number of ECC bytes per step
* Add a helper to retrieve the number of ECC steps
* Let ECC engines advertize the exact number of steps
* ECC Hamming:
- Populate the public nsteps field
- Use the public nsteps field
* ECC BCH:
- Populate the public nsteps field
- Use the public nsteps field
Raw NAND core:
* Add support for secure regions in NAND memory
* Try not to use the ECC private structures
* Remove duplicate include in rawnand.h
* BBT:
- Skip bad blocks when searching for the BBT in NAND (APPLIED THEN REVERTED)
Raw NAND controller drivers:
* Qcom:
- Convert bindings to YAML
- Use dma_mapping_error() for error check
- Add missing nand_cleanup() in error path
- Return actual error code instead of -ENODEV
- Update last code word register
- Add helper to configure location register
- Rename parameter name in macro
- Add helper to check last code word
- Convert nandc to chip in Read/Write helper
- Update register macro name for 0x2c offset
* GPMI:
- Fix a double free in gpmi_nand_init
* Rockchip:
- Use flexible-array member instead of zero-length array
* Atmel:
- Update ecc_stats.corrected counter
* MXC:
- Remove unneeded of_match_ptr()
* R852:
- replace spin_lock_irqsave by spin_lock in hard IRQ
* Brcmnand:
- Move to polling in pio mode on oops write
- Read/write oob during EDU transfer
- Fix OOB R/W with Hamming ECC
* FSMC:
- Fix error code in fsmc_nand_probe()
* OMAP:
- Use ECC information from the generic structures
SPI-NAND core:
* Add missing MODULE_DEVICE_TABLE()
SPI-NAND drivers:
* gigadevice: Support GD5F1GQ5UExxG
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmCBq3UACgkQJWrqGEe9
VoS9Xwf+I9W5WZS+WLYdlJ9RvuPDYVyZolZdsxIOOaOGuMAYSLJI/GjWJyHAFdwJ
qIPvr6qFnmKfUUaFZkln5Qk4QSfx+/t7+yj57e3lM9bSBEfTNToMI4AU8X6UAxa5
NHnsU8O8sohnk2UrP1qRtk3IezJ0FdzHbQAc82GQ1QY+IE0NwHg0ETjgESR5iEfq
PSnXb5Dgd637ENUlLsauSLbqFcD8sULvA3fJngxkQbBXDfv3KNZQhNsqw/l7NMY5
rROk8/jv7kgnYs8ObdkWO9SZ9QIiFSLk3vgbrTTNl8ozYpIMVbsrLmsnh7G34RNO
oWmbyOQdMDugaPYLJ9aTQmyI1qbKsA==
=zJPs
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core:
- Handle possible -EPROBE_DEFER from parse_mtd_partitions()
- Constify buf in mtd_write_user_prot_reg()
- Constify name param in mtd_bdi_init
- Fix fall-through warnings for Clang
- Get rid of Big MTD Lock ouf of mtdchar
- Drop mtd_mutex usage from mtdchar_open()
- Don't lock when recursively deleting partitions
- Use module_mtd_blktrans() to register driver when relevant
- Parse MTD as NVMEM cells
- New OTP (one-time-programmable) erase ioctl
- Require write permissions for locking and badblock ioctls
- physmap:
- Fix error return code of physmap_flash_remove()
- physmap-bt1-rom: Fix unintentional stack access
- ofpart parser:
- Support Linksys Northstar partitions
- Make symbol 'bcm4908_partitions_quirks' static
- Limit parsing of deprecated DT syntax
- Support BCM4908 fixed partitions
- Qcom parser:
- Incompatible with spi-nor 4k sectors
- Fix error condition
- Extend Qcom SMEM parser to SPI flash
CFI:
- Disable broken buffered writes for CFI chips within ID 0x2201
- Address a Coverity report for unused value
SPI NOR core:
- Add OTP support
- Fix module unload while an op in progress
- Add various cleanup patches
- Add Michael and Pratyush as designated reviewers in MAINTAINERS
SPI NOR controller drivers:
- intel-spi:
- Move platform data header to x86 subfolder
NAND core:
- Fix error handling in nand_prog_page_op() (x2)
- Add a helper to retrieve the number of ECC bytes per step
- Add a helper to retrieve the number of ECC steps
- Let ECC engines advertize the exact number of steps
- ECC Hamming:
- Populate the public nsteps field
- Use the public nsteps field
- ECC BCH:
- Populate the public nsteps field
- Use the public nsteps field
Raw NAND core:
- Add support for secure regions in NAND memory
- Try not to use the ECC private structures
- Remove duplicate include in rawnand.h
- BBT:
- Skip bad blocks when searching for the BBT in NAND (APPLIED THEN REVERTED)
Raw NAND controller drivers:
- Qcom:
- Convert bindings to YAML
- Use dma_mapping_error() for error check
- Add missing nand_cleanup() in error path
- Return actual error code instead of -ENODEV
- Update last code word register
- Add helper to configure location register
- Rename parameter name in macro
- Add helper to check last code word
- Convert nandc to chip in Read/Write helper
- Update register macro name for 0x2c offset
- GPMI:
- Fix a double free in gpmi_nand_init
- Rockchip:
- Use flexible-array member instead of zero-length array
- Atmel:
- Update ecc_stats.corrected counter
- MXC:
- Remove unneeded of_match_ptr()
- R852:
- replace spin_lock_irqsave by spin_lock in hard IRQ
- Brcmnand:
- Move to polling in pio mode on oops write
- Read/write oob during EDU transfer
- Fix OOB R/W with Hamming ECC
- FSMC:
- Fix error code in fsmc_nand_probe()
- OMAP:
- Use ECC information from the generic structures
SPI-NAND core:
- Add missing MODULE_DEVICE_TABLE()
SPI-NAND drivers:
- gigadevice: Support GD5F1GQ5UExxG"
* tag 'mtd/for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (89 commits)
Revert "mtd: rawnand: bbt: Skip bad blocks when searching for the BBT in NAND"
mtd: core: Constify buf in mtd_write_user_prot_reg()
Revert "mtd: spi-nor: macronix: Add support for mx25l51245g"
mtd: spi-nor: core: Fix an issue of releasing resources during read/write
mtd: cfi_cmdset_0002: remove redundant assignment to variable timeo
mtd: cfi_cmdset_0002: Disable buffered writes for AMD chip 0x2201
mtd: rawnand: qcom: Use dma_mapping_error() for error check
mtd: rawnand: gpmi: Fix a double free in gpmi_nand_init
mtd: rawnand: qcom: Add missing nand_cleanup() in error path
mtd: rawnand: Add support for secure regions in NAND memory
dt-bindings: mtd: Add a property to declare secure regions in NAND chips
dt-bindings: mtd: Convert Qcom NANDc binding to YAML
mtd: spi-nor: winbond: add OTP support to w25q32fw/jw
mtd: spi-nor: implement OTP support for Winbond and similar flashes
mtd: spi-nor: add OTP support
mtd: spi-nor: swp: Improve code around spi_nor_check_lock_status_sr()
mtd: spi-nor: Move Software Write Protection logic out of the core
mtd: rawnand: bbt: Skip bad blocks when searching for the BBT in NAND
include: linux: mtd: Remove duplicate include of nand.h
mtd: parsers: ofpart: support Linksys Northstar partitions
...
This reverts commit bd9c9fe2ad.
Since commit bd9c9fe2ad ("mtd: rawnand: bbt: Skip bad blocks when
searching for the BBT in NAND") the bad block table cannot be found
on a imx27-phytec-phycard-s-rdk board:
Bad block table not found for chip 0
Bad block table not found for chip 0
Revert it for now, until a better solution can be found.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210419140350.809853-1-festevam@gmail.com
The write buffer comes from user and should be const.
Constify write buffer in mtd core and across all _write_user_prot_reg()
users. cfi_cmdset_{0001, 0002} and onenand_base will pay the cost of an
explicit cast to discard the const qualifier since the beginning, since
they are using an otp_op_t function prototype that is used for both reads
and writes. mtd_dataflash and SPI NOR will benefit of the const buffer
because they are using different paths for writes and reads.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210403060931.7119-1-tudor.ambarus@microchip.com
struct ubi_wl_entry is defined at 178th line.
The declaration here is unnecessary. Remove it.
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
