Some code was calling v4l2_video_std_construct() when all it cared about
was the frame period. So make a function that just returns that and have
v4l2_video_std_construct() use it.
At this point there are no users of v4l2_video_std_construct() left outside
of v4l2-ioctl, so it could be un-exported and made static.
Change v4l2_video_std_construct() so that it doesn't zero out the struct
v4l2_standard passed in. It's already been zeroed out in the common ioctl
code.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bttv driver had static array of structures for up to 16 possible bttv
devices, even though few users have more than one or two. The structures
were quite large and this resulted in a huge BSS segment.
Change the driver to allocate the bttv device data dynamically, which
changes "struct bttv bttvs[BTTV_MAX]" to "struct bttv *bttvs[BTTV_MAX]".
It would be nice to get ride of "bttvs" entirely but there are some
complications with gpio access from the audio & mpeg drivers.
To help bttvs removal along anyway, I changed the open() methods use the
video device's drvdata to get the driver data instead of looking it up in
the bttvs array. This is also more efficient. Some WARN_ON()s are added
in cases the device node exists by the bttv device doesn't, which I don't
think should be possible.
The gpio access functions need to check if bttvs[card] is NULL now. Though
calling them on a non-existent card in the first place is wrong, but hard
to solve given the fundamental problems in how the gpio access code works.
This patch reduces the bss size by 66560 bytes on ia32. Overall change is a
reduction of 66398 bytes, as the WARN_ON()s add some 198 bytes.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Over half of the card database was used to store muxsel data. 64 bytes
were used to store one 32 bit word for each of up to 16 inputs.
The Bt8x8 only has two bits to control its mux, so muxsel data for 16
inputs will fit into a single 32 bit word. There were a couple cards that
had special muxsel data that didn't fit in two bits, but I cleaned them up
in earlier patches.
Unfortunately, C doesn't allow us to have an array of bit fields. This
makes initializing the structure more of a pain. But with some cpp magic,
we can do it by changing:
.muxsel = { 2, 3, 0, 1 },
.muxsel = { 2, 2, 2, 2, 3, 3, 3, 3, 1, 1 },
Into:
.muxsel = MUXSEL(2, 3, 0, 1),
.muxsel = MUXSEL(2, 2, 2, 2, 3, 3, 3, 3, 1, 1),
That's not so bad. MUXSEL is a fancy macro that packs the arguments (of
which there can be one to sixteen!) into a single word two bits at a time.
It's a compile time constant (a variadic function wouldn't be) so we can
use it to initialize the structure. It's important the the arguments to
the macro only be plain decimal integers. Stuff like "0x01", "(2)", or
"MUX3" won't work properly.
I also created an accessor function, bttv_muxsel(btv, input), that gets the
mux bits for the selected input. It makes it cleaner to change the way the
muxsel data is stored.
This patch doesn't change the code size and decreases the datasegment by
9440 bytes.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This card apparently uses an external mux and the Bt878's mux should always
be set to MUX2. The values for the external mux control bits were stored
in the muxsel field. This meant that when changing inputs the driver would
switch the Bt878's mux to whatever value the external mux was supposed to
be set to, then eagle_muxsel() would switch it back to MUX2 and program the
external mux. This creates an unnecessary switch of the Bt878's mux.
So change muxsel to be 2 for each input. The external mux bits are just
"input&3" so they don't really need to be stored anywhere. This also
eliminates the last non-standard use of the muxsel data.
Cc: M G Berberich <berberic@fmi.uni-passau.de>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Old versions of the bttv driver would use the high nibble of an input's
muxsel value to program the GPIO lines enabled via gpiomask2. Apparently
this was supposed to be for switching external audio muxes. Anyway, the
code that did this was removed sometime in the pre-git 2.6 series.
The RemoteVision MX board used this feature to control an external video
mux and I guess no one noticed when they removed the code.
Move the extra gpio mux data out of the high nibble of muxsel and to
rv605_muxsel(), then have that function set the gpio lines with it.
From looking at the CD22M3494E datasheet, it seems like the mdelay(1) is a
much longer delay than necessary. It looks like only around 20 ns is
necessary.
Cc: Miguel Freitas <miguel@cetuc.puc-rio.br>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Old versions of the bttv driver would use the high nibble of an input's
muxsel value to program the GPIO lines enabled via gpiomask2. Apparently
this was supposed to be for switching external audio muxes. Anyway, the
code that did this was removed sometime in the pre-git 2.6 series.
These phytec boards used this feature to control an external video mux and
I guess no one noticed when they removed the code.
So add a muxsel_hook for these boards that does the necessary gpio setting.
BTW, I doubt the needs_tvaudio setting for these cards is correct.
Cc: Dirk Heer <d.heer@phytec.de>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card data for BTTV_BOARD_IVC120 set muxsel to a bunch of bogus values
(1 to 16), which the common mux code would use to set the Bt878's mux to
some random value. Then the custom code in ivc120_muxsel() would change
the Bt878's mux to the right value (always MUX0).
Better to just make the muxsel data correct (all zeros, easy!) and get the
mux right to begin with. Then the extra Bt878 mux setting code in
ivc120_muxsel() can be eliminated (the rest of the code for the IVC-120G's
external mux is still there of course).
This will help me clean up muxsel for some other changes. It should also
get rid of an unnecessary mux switch when changing from certain inputs to
certain other inputs on the IVC-120G.
Cc: Alan Garfield <alan@fromorbit.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code was using a muxsel value of -1U to indicate a digital input. A
couple places in were checking of muxsel < 0 to detect this, which doesn't
work of course because muxsel is unsigned and can't be negative.
Only a couple cards had digital inputs and it was always the last one, so
for the card database create a one bit field that indicates the last input
is digital. On init, this is used to set a new field in the bttv struct to
the digital input's number or UNSET for none. This makes it easier to
check if the current input is digital.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bttv card database is quite large and the data structure used to store
it wasn't very efficient. Most of the field are only used at card
initialization time so it doesn't matter if they aren't efficient to
access.
Overall the changes reduce code size by 60 bytes in ia32. The data size is
decreased by 5024 byes. It is probably even more for 64-bit kernels.
Move the fields in the struct around to be sorted from largest to smallest.
This saves on padding space used for alignment.
Get rid of the unused digital_mode field. Leave the setting as a comment
in the few cards entries that set it, in case someone ever writes the code.
Get rid of the unused audio_inputs field. Leave the values in the card
entries in case someone ever writes code that might use it.
Get ride of the unused radio_addr field. No card entries even set it to
anything interesting so it's not left as comments. All the code that used
it was removed in commit v2.6.14-3466-g291d1d7 from Nov 8th 2005.
Reduce video_inputs to u8 as no card has more than 255 inputs (the most is
16).
Change tuner_addr to u8. I2C addresses are only seven bits and 255 means
ADDR_UNSET, so everything fits.
Make has_radio a one bit flag.
Make the pll setting a two bit field.
Reduce svhs to four bits as no card has an s-video input above 9. Change
the value for no s-video input from UNSET (which is -1U and out of range of
four bits) to NO_SVHS (which is now 15).
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bttv card database structure had a "tuner" field that was the input
number of the tuner input or UNSET for no tuner. However, the only values
it could ever be are 0 and UNSET. Having a tuner on an input other than 0
didn't work and was never used.
There is also a "tuner_type" field that can be set to TUNER_ABSENT to
indicate no tuner, which makes "tuner = UNSET" redundant. In many cases,
tuner_type was set to UNSET when there was no tuner, which isn't quite
correct. tuner_type == UNSET is supposed to mean the tuner type isn't yet
known.
So, I changed cards where "tuner == UNSET" to always have tuner_type of
TUNER_ABSENT. At this point the tuner field is redundant, so I deleted it.
I have the card setup code set the card's tuner_type (not the card type's
tuner_type!) to TUNER_ABSENT if it hasn't yet been set at the end of the
setup code. Various places that check if the card has a tuner will now
look for this instead of checking the card type's "tuner" field.
Also autoload the tuner module before issuing the TUNER_SET_TYPE_ADDR I2C
client call instead of after issuing it.
Overall, on ia32 this decreases compiled code size by about 24 bytes and
reduces the data size by 640 bytes.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code to set the norm for the TDA9880 analog demod was comparing
btv->norm, an index into the bttv driver's norm array, to V4L2_STD_NTSC,
which is a bit flag that's part of the V4L2 API. This doesn't work of
course and results in the PAL path always being taken.
What's more, it modified the bttv_tvcards[] entries for cards using the
TDA9880. This is wrong because changing the norm on one card will also
affect other cards of the same type. Writing to bttv_tvcards is also bad
because it should be read-only or even devinitdata.
Changing the norm would also cause the audio to become unmuted.
Have the code get called for both norm setting and audio input setting
(which where the gpios are set) to avoid needed to modify bttv_tvcards.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The norm value in the driver is an index into an array and the the driver
doesn't allow it to be negative or otherwise invalid. It should be
unsigned but wasn't in all places.
Fix some structs and functions to have the norm be unsigned. Get rid of
useless checks for "< 0". Most of the driver code can't handle a norm
value that's out of range, so change some ">= BTTV_TVNORMS" checks to
BUG_ON(). There's no point in silently ignoring invalid driver state just
to crash because of it later.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It's a quad Bt878 PCI-e x1 capture board that's basically the same as the
IVC-200 (quad Bt878 PCI) capture board that's currently supported in
the V4L2 bttv driver.
Manufacturer's web page for IVCE-8784 with photo and info:
http://www.iei.com.tw/en/product_IPC.asp?model=IVCE-8784
Signed-off-by: Douglas Kosovic <douglask@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The radio_release function of the BTTV driver is missing a call to
v4l2_prio_close. As a result, after the radio device has been opened at
least once (e.g., by HAL during bootup), v4l2_priority will never drop below
V4L2_PRIORITY_INTERACTIVE again. With the following patch against 2.6.28,
applications that run with V4L2_PRIORITY_BACKGROUND are able to open devices
again. Previous Linux versions are affected as well.
Signed-off-by: Udo Steinberg <udo@hypervisor.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the i2c driver ID will be removed in the near future we have to
modify the v4l2 debugging API to use the driver name instead of driver ID.
Note that this API is not used in applications other than v4l2-dbg.cpp
as it is for debugging and testing only.
Should anyone use the old VIDIOC_G_CHIP_IDENT, then this will be logged
with a warning that it is deprecated and will be removed in 2.6.30.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce a struct v4l2_file_operations for v4l2 drivers.
Remove the unnecessary inode argument.
Move compat32 handling (and llseek) into the v4l2-dev core: this is now
handled in the v4l2 core and no longer in the drivers themselves.
Note that this changeset reverts an earlier patch that changed the return
type of__video_ioctl2 from int to long. This change will be reinstated
later in a much improved version.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bt832 i2c driver was never used or even compiled and is no longer
maintained. It is now removed completely.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This Patch does modify the bttv-cards.c and bttc.h so that the driver
supports VD-011, VD-012, VD-012-X1 and VD-012-X2 Framegrabber from
Phytec Messtechnik GmbH.
Signed-off-by: Dirk Heer <d.heer@phytec.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The BT8XX device driver currently only supports 16 such devices in a
system. This is too small for many surveillance applications. This
patch increases the number to 32.
Signed-off-by: Alan McIvor <alan.mcivor@reveal.co.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
We want to submit a patch to -next, which will remove bus_id from
"struct device", to find the remaining pieces to convert, and finally
switch over to the new api, which will remove the 20 bytes array
and does no longer have a size limitation.
Thanks,
Kay
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The kernel number of a v4l2 node (e.g. videoX, radioX or vbiX) is now
independent of the minor number. So instead of using the minor field
of the video_device struct one has to use the num field: this always
contains the kernel number of the device node.
I forgot about this when I did the v4l2 core change, so this patch
converts all drivers that use it in one go. Luckily the change is
trivial.
Cc: michael@mihu.de
Cc: mchehab@infradead.org
Cc: corbet@lwn.net
Cc: luca.risolia@studio.unibo.it
Cc: isely@pobox.com
Cc: pe1rxq@amsat.org
Cc: royale@zerezo.com
Cc: mkrufky@linuxtv.org
Cc: stoth@linuxtv.org
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the vidioc_enum_fmt_vbi_cap ops: it was scheduled for removal in
2.6.28 since the v4l2 specification says that V4L2_BUF_TYPE_VBI_CAPTURE should
not support VIDIOC_ENUM_FMT. It's also pretty pointless.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With video_nr, vbi_nr and radio_nr being simple integers, it is not
possible to use these parameters on a system with multiple bttv
adapters (which happens to be my case.) video_register_device() will
always fail on the second and later adapters. Turn these parameters
into arrays, as many other V4L drivers are already doing, so that they
can be used on such systems.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the input is set to tuner and no antenna is connected, the BT848
can flood VPRES interrupts. So we don't want to enable this type of
interrupts when the input it set to tuner.
As we don't do anything when receiving such an interrupt anyway, the
easiest fix is to simply not unmask this specific interrupt.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) and CDI Brasil
(www.cdibrasil.com.br/) for sponsoring this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The BKL is now moved from the video_open function in v4l2-dev.c to the
various drivers. It seems about a third of the drivers already has a
lock of some sort protecting the open(), another third uses
video_exclusive_open (yuck!) and the last third required adding the
BKL in their open function.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the following crash in the bttv driver:
BUG: unable to handle kernel NULL pointer dereference at 000000000000036c
IP: [<ffffffffa037860a>] radio_open+0x3a/0x170 [bttv]
This happens because radio_open assumes that all present bttv devices
have a radio function. If a bttv device without radio and one with
radio are installed on the same system, and the one without radio is
registered first, then radio_open checks for the radio device number
of a bttv device that has no radio function, and this breaks. All we
have to do to fix it is to skip bttv devices without a radio function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
b2c2-flexcop, dvb/bt8xx and video/bt8xx fails to build on ARM with:
__bad_udelay is specifically designed on ARM to fail when udelay is
called in a bad way. arch/arm/include/asm/delay.h has this to say
about __bad_udelay:
/*
* This function intentionally does not exist; if you see references to
* it, it means that you're calling udelay() with an out of range value.
*
* With currently imposed limits, this means that we support a max delay
* of 2000us. Further limits: HZ<=1000 and bogomips<=3355
*/
extern void __bad_udelay(void);
Solution is to replace udelay by a mdelay and udelay with value less than 2000
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed a lot of sparse warnings: mostly warnings about shadowed variables
and signed/unsigned mismatches.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After commit d9b19199e4
(always enable FW_LOADER unless EMBEDDED=y) we can remove
the FW_LOADER select's and corresponding dependencies
on HOTPLUG.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The type and type2 fields were unused and so could be removed.
Instead add a vfl_type field that contains the type of the video
device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All ioctl callbacks are now stored in a new v4l2_ioctl_ops struct. Drivers fill in
a const struct v4l2_ioctl_ops and video_device just contains a const pointer to it.
This ensures a clean separation between the const ops struct and the non-const
video_device struct.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The functions in a header should not belong to another module. The prio functions
belong to v4l2-common.c, so move them to v4l2-common.h.
The ioctl functions belong to v4l2-ioctl.c, so create a new v4l2-ioctl.h header
and move those functions to it.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The class_dev field is a normal device, not a class device. This is very
confusing and now that the old 'dev' field has been renamed to 'parent'
we can rename 'class_dev' to just 'dev'.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The field 'dev' is not the video device, but the parent of the video device.
Rename accordingly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Also remove some blank lines that were used to split compat code at -devel
tree.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clean up the use of structure templates in bttv-i2c. For one thing, a
real template is supposed to be read-only. And in some cases it's more
efficient to initialize the few fields we need individually.
This clean-up shrinks bttv-i2c.o by 29% (x86_64).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The naming for the callbacks that handle the VIDIOC_ENUM_FMT and
VIDIOC_S/G/TRY_FMT ioctls was very confusing. Renamed it to match
the v4l2_buf_type name.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
vidiocgmbuf() does this:
mutex_lock(&fh->cap.vb_lock);
retval = videobuf_mmap_setup(&fh->cap, gbuffers, gbufsize,
V4L2_MEMORY_MMAP);
and videobuf_mmap_setup() then just does
mutex_lock(&q->vb_lock);
ret = __videobuf_mmap_setup(q, bcount, bsize, memory);
mutex_unlock(&q->vb_lock);
which is an obvious double-take deadlock.
This patch fixes this by having vidiocgmbuf() just call the
__videobuf_mmap_setup function instead.
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Reported-by: Koos Vriezen <koos.vriezen@gmail.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since:
1) FW_LOADER is defined as:
config FW_LOADER
tristate "Userspace firmware loading support"
depends on HOTPLUG
2) several V4L/DVB driver just selects it;
3) select is not smart enough to auto-select HOTPLUG, if select FW_LOADER.
So, All drivers that select FW_LOADER should also depend on HOTPLUG.
An easier solution (for the end-user perspective) would be to "select HOTPLUG".
However, live is not simple. This would cause recursive dependency issues like
this one:
drivers/usb/Kconfig:62:error: found recursive dependency: USB -> USB_OHCI_HCD
-> I2C -> MEDIA_TUNER -> MEDIA_TUNER_XC2028 -> HOTPLUG -> PCCARD -> PCMCIA ->
USB_ARCH_HAS_HCD -> MOUSE_APPLETOUCH -> USB
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDEO_TUNER is responsible for compilation of tuners.ko module. This were the
previous behaviour before the creation of MEDIA_TUNER.
Before this patch, tuner.ko were created even for drivers that don't need a
tuner (like webcam drivers).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Also, change the variable names used in the min/max macros to avoid shadowed
variable warnings when min/max min_t/max_t are nested.
Small formatting changes to make all the macros have a similar form.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix v4l build]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There were several issues in the past, caused by the hybrid tuner design, since
now, the same tuner can be used by drivers/media/dvb and drivers/media/video.
Kconfig items were rearranged, to split V4L/DVB core from their drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the leak of the bttv_fh structure allocated in radio_open which
was introduced by commit 5cd3955cb8.
Signed-off-by: Robert Fitzsimons <robfitz@273k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert dvb-bt8xx to use tuner-simple instead of dvb-pll for Philips FCV1236D
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
TUNER_PHILIPS_ATSC is an ambiguous name for a tuner. Rename it to
TUNER_PHILIPS_FCV1236D to be more descriptive.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I have what looks like a Geovision GV-600 (or 650) card. It has a large
chip in the middle labeled
CONEXANT
FUSION 878A
25878-13
E345881.1
0312 TAIWAN
It has an audio connector coming out from a chip labeled
ATMEL
0242
AT89C2051-24PI
It is identified as follows on my Debian GNU/Linux Etch (kernel 2.6.18)
...
01:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
01:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
...
01:0a.0 0400: 109e:036e (rev 11)
Subsystem: 008a:763c
Flags: bus master, medium devsel, latency 64, IRQ 58
Memory at dfffe000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
01:0a.1 0480: 109e:0878 (rev 11)
Subsystem: 008a:763c
Flags: bus master, medium devsel, latency 64, IRQ 58
Memory at dffff000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
It was being detected as a GENERIC UNKNOWN CARD both by the 2.6.18
kernel and the latest v4l-dvb drivers, but it did not work at all. The
card has sixteen (16) BNC video inputs, four of them on the board itself
and twelve on three daughter-cards. It has a single bt878 chip, no tuner
and what looks like and audio input. After doing some research I managed
to get only eight channels working by forcing card=125 and those DID NOT
match channels 0-7 on the card, and no audio.
Based on what was working for card=125, I added the card definition
block, added a specific muxsel routine and got the card working fully
with xawtv, where the sixteen channels show up as Composite0 to
Composite15, matching the channel labels in the card and daughter-cards.
I have made no efforts yet to get audio working, but would appreciate
any pointers.
Signed-off-by: Ernesto Hernández-Novich <emhn@usb.ve>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The PixelView PlayTV card definition structure was missing initialization of
the tuner_addr and radio_addr fields. As a result it was impossible to have the
tuner initialized using parameters specified while loading the bttv.ko module.
This regression became visible after the v4l rearrangements introduced
somewhere around 2.6.15 kernel version.
The root cause for the tuner initialization failure is located in the
attach_inform function in the bttv-i2c.c file.
There at the very beginning the addr variable holding the tuner device address
is initialized with the value taken from the bttv_tvcards array.
For the PixelView PlayTV card the tuner address field (and the radio address as
well) was uninitialized, and thus equal 0. Later in that function execution of
the TUNER_SET_TYPE_ADDR tuner command is guarded with check for the tuner
address either equal ADDR_UNSET, or client->addr.
Since both are non-zero (the latter in case of the card owned by me at the
runtime is equal 0x61) the TUNER_SET_TYPE_ADDR command is not executed, and
consequently in the tuner_attach function in the tuner-core.c file call to
i2c_attach_client does not result in assigning the tuner type variable with the
requested value.
Providing initialization of the tuner_addr and radio_addr with ADDR_UNSET
values as it is already done for other tv cards defined in bttv-cards.c ensures
that the tuner initialization is done correctly, just as it used to be in the
2.6.14 kernel.
Signed-off-by: Wojciech Migda <wojtek.golf@interia.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
videobuf-dma-sg does not need to depend on PCI. Switch it to using generic
DMA API, convert all affected drivers, relax Kconfig restriction, improve
compile-time type checking, fix some Coding Style violations while at it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Static memory is always initialized with 0.
- Replaced in some cases C99 comments for /* */
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We should check for proper index first
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A number of the radio tuner ioctl functions are shared with the TV
tuner, these functions require a struct bttv_fh data structure to be
allocated and initialized.
Signed-off-by: Robert Fitzsimons <robfitz@273k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
fixes sparse warning:
drivers/media/video/bt8xx/bttv-driver.c:3391:3: warning: Initializer entry defined twice
drivers/media/video/bt8xx/bttv-driver.c:3392:3: also defined here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The initial work to convert the bttv driver to V4L2 "Partial conversion
from V4L1 to V4L2" (e84619b174), missed
the line which set the appropriate overlay crop structure in the newly
allocated bttv_buffer. This then causes a divide error in the
bttv_calc_geo function.
Signed-off-by: Robert Fitzsimons <robfitz@273k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
IR were not working for Winfast XP 2000 TV.
Gabor Nyekhelyi <n0gabor@vipmail.hu> wrote a hack some time ago:
http://marc.info/?l=linux-video&m=116362609323281&w=2
This patch fixes CodingStyle and commits the hack. I suspect that the proper
solution would be to find the proper mask_keydown for this IR. Anyway, better
to have this patch as a workaround.
Thanks to Stafan Talpalaru <stefantalpalaru@yahoo.com> for pointing the issue.
CC: Gabor Nyekhelyi <n0gabor@vipmail.hu>
CC: Stafan Talpalaru <stefantalpalaru@yahoo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
bttv driver is working as previously. An additional gain of about 1,5Kb were
obtained with the driver conversion to vidioc_ioctl2:
text data bss dec hex filename
89208 40244 57556 187008 2da80 old/bttv.ko
88960 38740 57556 185256 2d3a8 new/bttv.ko
(measured on a x86_64)
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since there are a few vidioc_ functions that were exported, rename those
functions to bttv_ in order to avoid poluting namespace.
The other functions were also renamed, to standardize inside the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Someone wasn't using the v4l-dvb commit scripts and so didn't run the
automatic whitespace cleaner on their code.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several media drivers use input_(*) functions so they need to depend on
the INPUT config symbol.
drivers/built-in.o: In function `bttv_input_fini':
linux-2.6.24-rc1-git4/drivers/media/video/bt8xx/bttv-input.c:346: undefined reference to `input_unregister_device'
drivers/built-in.o: In function `bttv_input_init':
linux-2.6.24-rc1-git4/drivers/media/video/bt8xx/bttv-input.c:204: undefined reference to `input_allocate_device'
linux-2.6.24-rc1-git4/drivers/media/video/bt8xx/bttv-input.c:335: undefined reference to `input_free_device'
linux-2.6.24-rc1-git4/drivers/media/video/bt8xx/bttv-input.c:321: undefined reference to `input_register_device'
linux-2.6.24-rc1-git4/drivers/media/video/bt8xx/bttv-input.c:335: undefined reference to `input_free_device'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is part of the old V4L1->V4L2 bttv patch, ported to current tree
by Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is part of the old V4L1->V4L2 bttv patch, ported to current tree
by Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is part of the old V4L1->V4L2 bttv patch, ported to current tree
by Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently, the only tuner-specific device that allows special
configurations is tda9887. However, tea5767 also may require some
special configurations (for example, to specify a different Xtal freq).
This patch replaces TDA9887_SET_CONFIG by a more generic internal ioctl
(TUNER_SET_CONFIG). The newer one allows specifying what tuner is
appliable to a configuration set, and allows an arbitrary configuration
struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Drivers were using cookie cutter code for stopping the read/stream. Use the
new videobuf_stop function which is lock safe.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The V4L1 spec says that the image size should be with with VIDIOCSWIN before
requesting buffers with VIDIOCGMBUF and capturing into them with
VIDIOCMCAPTURE.
But it seems that many apps don't do this. They set the size using the fields
in the VIDIOCMCAPTURE ioctl. The driver doesn't know what size to capture
until it actually starts to capture. In particular, it doesn't know what size
to capture until it has already mmap the captured buffers. Which is quite
stupid. Why V4L1 has size and format fields for VIDIOCMCAPTURE I have no idea.
Many drivers don't support this, including those using v4l1-compat.
The bttv does, which is probably the only reason such broken software is so
prevalent.
But, the driver doesn't adjust its idea of what size is being captured when it
is set this way. If you try to query the driver's current setting with
v4l2-ctl, it won't be correct.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The bttv driver instists that the depth specified in the call to VIDIOCSPICT
match the pixel format specified in the same call.
vlc doesn't set the depth field, which makes the SPICT ioctl always fail.
The V4L1 standard is not clear on how most operation are supposed to work, and
this is no exception. The depth field would appear to be entirely redundant,
as the pixel format specifies a specific depth. It could be that this field
was only meant for output from the *G*PICT ioctl and should be ignored in
*S*PICT. This is in fact what the v4l1-compat wrapper does.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Not architecture specific code should not #include <asm/scatterlist.h>.
This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
struct video_device used to define a .hardware field. While
initialized on severl drivers, this field is never used inside V4L.
However, drivers using it need to include the old V4L1 header.
This seems to cause compilation troubles with some random configs.
Better just to remove it from all drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
This removes NOP implementations of i2c_algorithm.algo_control.
With this change, there are no implementations of this hook in
the kernel.org tree ... that hook seems about ripe to remove.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
