All lanes in data-lanes and clock-lanes properties should be unique. Add
a check for this in v4l2_of_parse_csi_bus() and print a warning if
duplicated lanes are found.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds some trace points showing input compressed stream or
output decoded frame information.
Adds an unconditional trace point when streaming starts showing
the compressed stream and the decoded frame information.
Adds an unconditional trace point at instance closure summarizing
into a single line the decoding process (stream information, decoded
and output frames number, potential errors observed).
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds support of DELTA MJPEG video decoder back-end,
implemented by calling JPEG_DECODER_HW0 firmware
using RPMSG IPC communication layer.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
EOS (End Of Stream) support allows user to get
all the potential decoded frames remaining in decoder
pipeline after having reached the end of video bitstream.
To do so, user calls VIDIOC_DECODER_CMD(V4L2_DEC_CMD_STOP)
which will drain the decoder and get the drained frames
that are then returned to user.
User is informed of EOS completion in two ways:
- dequeue of an empty frame flagged to V4L2_BUF_FLAG_LAST
- reception of a V4L2_EVENT_EOS event.
If, unfortunately, no buffer is available on CAPTURE queue
to return the empty frame, EOS is delayed till user queue
one CAPTURE buffer.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
IPC (Inter Process Communication) support for communication with
DELTA coprocessor firmware using rpmsg kernel framework.
Based on 4 services open/set_stream/decode/close and their associated
rpmsg messages.
The messages structures are duplicated on both host and firmware
side and are packed (use only of 32 bits size fields in messages
structures to ensure packing).
Each service is synchronous; service returns only when firmware
acknowledges the associated command message.
Due to significant parameters size exchanged from host to copro,
parameters are not inserted in rpmsg messages. Instead, parameters are
stored in physical memory shared between host and coprocessor.
Memory is non-cacheable, so no special operation is required
to ensure memory coherency on host and on coprocessor side.
Multi-instance support and re-entrance are ensured using host_hdl and
copro_hdl in message header exchanged between both host and coprocessor.
This avoids to manage tables on both sides to get back the running context
of each instance.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Helper functions used by decoder back-ends to allocate
physically contiguous memory required by hardware video
decoder.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Internal Master 3 Bus can send and receive only 4 bytes per time.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch provide only digital support.
The device is based on Si2168 30-demodulator,
Si2158-20 tuner and CX23102-11Z chipset;
USB id: 1b80:d3b2.
Status:
- DVB-T2 works fine;
- Composite and SVideo works fine;
- Analog not implemented.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2-async had several functions doing some operations and then
not undoing the operations in a failure situation. For example,
v4l2_async_test_notify() moved a subdev into notifier's done list
even if registering the subdev (v4l2_device_register_subdev) failed.
If the subdev was allocated and v4l2_async_register_subdev() called
from the driver's probe() function, as usually, the probe()
function freed the allocated subdev and returned a failure.
Nevertheless, the subdev was still left into the notifier's done
list, causing an access to already freed memory when the notifier
was later unregistered.
A hand-edited call trace leaving freed subdevs into the notifier:
v4l2_async_register_notifier(notifier, asd)
cameradrv_probe
sd = devm_kzalloc()
v4l2_async_register_subdev(sd)
v4l2_async_test_notify(notifier, sd, asd)
list_move(sd, ¬ifier->done)
v4l2_device_register_subdev(notifier->v4l2_dev, sd)
cameradrv_registered(sd) -> fails
->v4l2_async_register_subdev returns failure
->cameradrv_probe returns failure
->devres frees the allocated sd
->sd was freed but it still remains in the notifier's list.
This patch fixes this and several other cases where a failing
function could leave nodes into a linked list while the caller
might free the node due to a failure.
Signed-off-by: Tuukka Toivonen <tuukka.toivonen@intel.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We should be returning negative error codes here or it leads to a crash.
This also silences a static checker warning.
drivers/media/pci/mantis/mantis_cards.c:250 mantis_pci_probe()
warn: 'mantis->dmxdev.dvbdev->fops' double freed
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There isn't an ioctl to enum the supported field orders, so a user-space
application can call VIDIOC_TRY_FMT using different field orders to know
if one is supported. For example, GStreamer does this so during playback
dozens of the following messages appear in the kernel log buffer:
[ 442.143393] Not supported field order(4)
Instead of printing this as an error, just keep it as debug information.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It is likely that a "of_node_put(ep)" is missing here.
There is one in the previous error handling code, and one a few lines
below in the normal case as well.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Declare vb2_ops structure as const as it is only stored in
the ops field of a vb2_queue structure. This field is of type
const, so vb2_ops structures having same properties can be made
const too.
Done using Coccinelle:
@r1 disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p={...};
@ok1@
identifier r1.i;
position p;
struct sta2x11_vip vip;
struct vb2_queue q;
@@
(
vip.vb_vidq.ops=&i@p
|
q.ops=&i@p
)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct vb2_ops i;
File size details of media/dvb-frontends/rtl2832_sdr.o file remains the
same before and after applying the patch.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Declare vb2_ops structure as const as it is only stored in
the ops field of a vb2_queue structure. This field is of type
const, so vb2_ops structures having same properties can be made
const too.
Done using Coccinelle:
@r1 disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p={...};
@ok1@
identifier r1.i;
position p;
struct sta2x11_vip vip;
struct vb2_queue q;
@@
(
vip.vb_vidq.ops=&i@p
|
q.ops=&i@p
)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct vb2_ops i;
File size before:
text data bss dec hex filename
8448 440 0 8888 22b8 media/pci/sta2x11/sta2x11_vip.o
File size after:
text data bss dec hex filename
8552 352 0 8904 22c8 media/pci/sta2x11/sta2x11_vip.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set the subdev devnode pointer right after registration to ensure that
later errors won't skip the subdev when unregistering all devnodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Freescale provided imx-vpu looks for firmware files under /lib/firmware/vpu
by default. Make coda look there for firmware files to ease the update path.
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The UK layout of the Microsoft Remote Keyboard has two missing keys:
the hash key, and the messenger key which is sent using rc6 mce.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Bail out early, otherwise we follow a null pointer.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixes the following sparse warning:
drivers/media/usb/dvb-usb/gp8psk.c:281:28: warning:
symbol 'gp8psk_fe_ops' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hauppauge WinTV-dualHD model 01595 is a USB 2.0 dual ATSC/QAM tuner with
the following components:
USB bridge: Empia em28274
Demodulator: 2x LG LGDT3306a at addresses 0xb2 and 0x1c
Tuner: 2x Silicon Labs si2157 at addresses 0xc0 and 0xc4
This patch enables only the first tuner.
Signed-off-by: Kevin Cheng <kcheng@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds an i2c mux to the lgdt3306a demodulator. This was done to support
the Hauppauge WinTV-dualHD 01595 USB TV tuner (em28xx), which utilizes two
si2157 tuners behind gate control.
Signed-off-by: Kevin Cheng <kcheng@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While the wakeup path seems to be set up, this waitqueue is actually
never used as no-one enqueues themselves on the list. As such, wakeups
are meaningless without waiters, so lets just get rid of the whole
thing.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Using %4s to format f->fmt.pix_mp.pixelformat in fdp1_try_fmt() and
fdp1_s_fmt() may lead to more characters being printed (when the byte
following field pixelformat is not zero).
Add ".4" to the format specifier to limit the number of printed
characters to four. The resulting format specifier "%4.4s" is also used
by other media drivers to print pixelformat value.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Reviewed-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With this patch we use the new style to attach the frontend.
Signed-off-by: Niels Ole Salscheider <niels_ole@salscheider-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In AER recovery, pci_error_handlers.link_reset() is never called,
drop it now.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned by gcc:
drivers/media/usb/stk1160/stk1160-ac97.c:117:5: warning: no previous prototype for 'stk1160_has_audio' [-Wmissing-prototypes]
int stk1160_has_audio(struct stk1160 *dev)
^~~~~~~~~~~~~~~~~
drivers/media/usb/stk1160/stk1160-ac97.c:125:5: warning: no previous prototype for 'stk1160_has_ac97' [-Wmissing-prototypes]
int stk1160_has_ac97(struct stk1160 *dev)
^~~~~~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The STK1160 needs some time to transfer data to and from the AC97 codec.
The transfer completion is indicated by command read/write bits in the
chip's audio control register. The driver should poll these bits and
wait until they have been cleared by hardware before trying to retrieve
the results of a read operation or setting a new write command.
[mchehab@s-opensource.com: make checkpatch happier]
Signed-off-by: Marcel Hasler <mahasler@gmail.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some STK1160-based devices use the chip's internal 8-bit ADC. This is
configured through a strap pin. The value of this and other pins can be
read through the POSVA register. If the internal ADC is used, or if
audio is disabled altogether, there's no point trying to setup the AC97
codec.
Signed-off-by: Marcel Hasler <mahasler@gmail.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Exposing all the channels of the device's internal AC97 codec to
userspace is unnecessary and confusing. Instead the driver should setup
the codec with proper values. This patch removes the mixer and sets up
the codec using optimal values, i.e. the same values set by the Windows
driver. This also makes the device work out-of-the-box, without the need
for the user to reconfigure the device every time it's plugged in.
Signed-off-by: Marcel Hasler <mahasler@gmail.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check that the control whose events we want to delete is still there.
Normally this will always be the case, but I am not 100% certain if
there aren't any corner cases when a device is forcibly unbound.
In any case, this will satisfy static checkers and simply make it more
robust.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Shaobo <shaobo@cs.utah.edu>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Stop accessing timer struct members directly and use the setup_timer
helper intended for that use. It makes the code cleaner and will allow
for easier change of the timer struct internals.
Signed-off-by: Matej Hulín <mito.hulin@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The error message when the second image is not available is incorrect,
replace "first image" with "second image".
Fixes CoverityScan CID#1077508 ("Copy-paste error")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The comparison of err < 0 is redundant as err has been previously
been assigned to 0 and has not changed. Remove the redundant check.
Fixes CoverityScan CID#703363 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The control for +5V Power detection must also be updated when the EDID is
not present.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Originally Toshiba told us that the only way to disable HDCP was to
set the receiver in repeater mode, that would make the authentication
fail because of missing software support. It has worked fine with all
the sources we and our customers has used, until it was reported
problems with Apple MacBook (Retina, 12-inch, Early 2015)
(https://support.apple.com/kb/SP712?locale=en_US&viewlocale=en_US)
with Apple A1612 USB type-C multiport adapter
(http://www.apple.com/shop/product/MJ1K2AM/A/usb-c-digital-av-multiport-adapter)
Finally Toshiba came up with a hidden bit that is named "Manual HDCP
authentication". In this patch the original "repeater mode" concept is
removed, and the new bit is set instead.
With his patch HDCP is disabled when connected to the Apple MacBook
and all other sources we have tested so far. The Apple MacBook is
constantly trying to authenticate, but fails and continues to transmit
unencrypted video.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The number of CSI lanes that should be used is set to the CSI_CONTROL
register by indirectly writing to the CSI_CONFW register. When the
number of lanes is read back from the CSI_CONTROL register the value
is usually correct, but we have seen that it suddenly is 1 for a short
moment before the correct value is restored again.
Toshiba have not figured out why that happen, but we have found it
safer to store the value in the driver.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for v4l2_subdev_ops structures that are only passed as an
argument to the function v4l2_subdev_init. This argument is of type
const, so v4l2_subdev_ops structures having this property can also be
declared const.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
@@
v4l2_subdev_init(...,&i@p)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_ops i;
File size before:
text data bss dec hex filename
17171 1912 20 19103 4a9f
platform/s3c-camif/camif-capture.o
File size after:
text data bss dec hex filename
17235 1848 20 19103 4a9f
platform/s3c-camif/camif-capture.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dib7000p_read_word() may return zero on i2c errors, resulting in
dib7000p_get_internal_freq() returning zero.
So don't divide by the result of dib7000p_get_internal_freq()
without checking it for zero in dib7000p_set_dds().
On one of my machines the device
ID 2304:0229 Pinnacle Systems, Inc. PCTV Dual DVB-T 2001e
about once a day/every two days gets into a state, where
most (all?) I2C reads return with an error. Tuning during this
state will result in a divide by zero without this patch.
This patch doesn't fix the root cause for the device getting
into a bad state, but it allows me to unload/reload the drivers,
bringing it back into a usable state.
Signed-off-by: Martin Wache <M.Wache@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_{core/video}_ops structures are stored in the
fields of the v4l2_subdev_ops structure which are of type const.
Also, v4l2_subdev_ops structure is passed to a function
having its argument of type const. As these structures are never
modified, so declare them as const.
Done using Coccinelle: (One of the scripts used)
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
@@
v4l2_i2c_subdev_init(...,&i@p)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_ops i;
File size before:
text data bss dec hex filename
2732 608 8 3348 d14 drivers/media/i2c/ml86v7667.o
File size after:
text data bss dec hex filename
3100 232 8 3340 d0c drivers/media/i2c/ml86v7667.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_{core/video}_ops structures are stored in the
fields of the v4l2_subdev_ops structure which are of type const.
Also, v4l2_subdev_ops structure is passed to a function
having its argument of type const. As these structures are never
modified, so declare them as const.
Done using Coccinelle: (One of the scripts used)
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_video_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
struct v4l2_subdev_ops obj;
@@
obj.video=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_video_ops i;
File size before:
text data bss dec hex filename
1809 872 0 2681 a79 drivers/media/i2c/ak881x.o
File size after:
text data bss dec hex filename
2185 496 0 2681 a79 drivers/media/i2c/ak881x.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_pad_ops structures are stored in the pad field
of the v4l2_subdev_ops structure and this field is of type const.
As the v4l2_subdev_pad_ops structures are never modified, they can be
declared as const.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_pad_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
struct v4l2_subdev_ops obj;
@@
obj.pad=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_pad_ops i;
File size before:
text data bss dec hex filename
7633 512 20 8165 1fe5 media/i2c/m5mols/m5mols_core.o
File size after:
text data bss dec hex filename
7761 384 20 8165 1fe5 media/i2c/m5mols/m5mols_core.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This delay is in non-atomic context and it does not seem to be
time-critical so relax it to allow the timer subsystem to optimize
hrtimers.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_{core/pad/video}_ops structures are stored in the
fields of the v4l2_subdev_ops structure which are of type const.
Also, v4l2_subdev_ops structure is passed to a function
having its argument of type const. As these structures are never
modified, so declare them as const.
Done using Coccinelle: (One of the scripts used)
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_video_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
struct v4l2_subdev_ops obj;
@@
obj.video=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_video_ops i;
File sizes before:
text data bss dec hex filename
7810 736 16 8562 2172 drivers/media/i2c/mt9p031.o
9652 736 24 10412 28ac drivers/media/i2c/mt9v032.o
4613 552 20 5185 1441 drivers/media/i2c/noon010pc30.o
2615 552 8 3175 c67 drivers/media/i2c/s5k6a3.o
File sizes after:
text data bss dec hex filename
8322 232 16 8570 217a drivers/media/i2c/mt9p031.o
10164 232 24 10420 28b4 drivers/media/i2c/mt9v032.o
4933 232 20 5185 1441 drivers/media/i2c/noon010pc30.o
2935 232 8 3175 c67 drivers/media/i2c/s5k6a3.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_{core/pad/video}_ops structures are stored in the
fields of the v4l2_subdev_ops structure which are of type const.
Also, v4l2_subdev_ops structure is passed to a function
having its argument of type const. As these structures are never
modified, so declare them as const.
Done using Coccinelle: (One of the scripts used)
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_video_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
struct v4l2_subdev_ops obj;
@@
obj.video=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_video_ops i;
File size before:
text data bss dec hex filename
6170 2752 144 9066 236a media/platform/xilinx/xilinx-tpg.o
File size after:
text data bss dec hex filename
6666 2384 8 9058 2362 media/platform/xilinx/xilinx-tpg.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
