Secure discard is the same as discard except that all copies of the
discarded sectors (perhaps created by garbage collection) must also be
erased.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 83ba7b071f ("writeback: simplify the write back thread queue")
broke writeback_in_progress() as in that commit we started to remove work
items from the list at the moment we start working on them and not at the
moment they are finished. Thus if the flusher thread was doing some work
but there was no other work queued, writeback_in_progress() returned
false. This could in particular cause unnecessary queueing of background
writeback from balance_dirty_pages() or writeout work from
writeback_sb_if_idle().
This patch fixes the problem by introducing a bit in the bdi state which
indicates that the flusher thread is processing some work and uses this
bit for writeback_in_progress() test.
NOTE: Both callsites of writeback_in_progress() (namely,
writeback_inodes_sb_if_idle() and balance_dirty_pages()) would actually
need a different information than what writeback_in_progress() provides.
They would need to know whether *the kind of writeback they are going to
submit* is already queued. But this information isn't that simple to
provide so let's fix writeback_in_progress() for the time being.
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split get_dirty_limits() into global_dirty_limits()+bdi_dirty_limit(), so
that the latter can be avoided when under global dirty background
threshold (which is the normal state for most systems).
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ACPI_PREEMPTION_POINT() logic was introduced in commit 8bd108d
(ACPICA: add preemption point after each opcode parse). The follow up
commits abe1dfab6, 138d15692, c084ca70 tried to fix the preemption logic
back and forth, but nobody noticed that the usage of
in_atomic_preempt_off() in that context is wrong.
The check which guards the call of cond_resched() is:
if (!in_atomic_preempt_off() && !irqs_disabled())
in_atomic_preempt_off() is not intended for general use as the comment
above the macro definition clearly says:
* Check whether we were atomic before we did preempt_disable():
* (used by the scheduler, *after* releasing the kernel lock)
On a CONFIG_PREEMPT=n kernel the usage of in_atomic_preempt_off() works by
accident, but with CONFIG_PREEMPT=y it's just broken.
The whole purpose of the ACPI_PREEMPTION_POINT() is to reduce the latency
on a CONFIG_PREEMPT=n kernel, so make ACPI_PREEMPTION_POINT() depend on
CONFIG_PREEMPT=n and remove the in_atomic_preempt_off() check.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16210
[akpm@linux-foundation.org: fix build]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Len Brown <lenb@kernel.org>
Cc: Francois Valenduc <francois.valenduc@tvcablenet.be>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add mfd core driver for TPS6586x PMICs family.
The driver provides I/O access for the sub-device drivers and performs
regstration of the sub-devices based on the platform requirements.
In addition it implements GPIOlib interface for the chip GPIOs.
TODO:
- add interrupt support
- add platform data for PWM, backlight leds and charger
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Mike Rapoport <mike.rapoport@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds all remaining definitions that are used by the core driver
to the .c file.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is needed for the mc13783-adc driver to decide if a touch screen is
connected. If so some channels are not available as generic hwmon inputs.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some STMPE devices support entering sleep mode automatically on a
specified timeout of inactivity on the I2C bus with the host system.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Later revisions of the WM8994 add some more GPIO functions, define them
in the header file.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds a MFD driver for the JZ4740 ADC unit. The driver is used to
demultiplex IRQs and synchronize access to shared registers between the
battery, hwmon and (future) touchscreen driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for the STMPE family of I/O Expanders from
STMicroelectronics. These devices include upto 24 gpios and a varying
selection of blocks, including PWM, keypad, and touchscreen controllers.
This patch adds the MFD core.
[l.fu@pengutronix.de: fix stmpe811 enable hook]
[l.fu@pengutronix.de: add touchscreen platform data]
Acked-by: Luotao Fu <l.fu@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Split max_io_len_target_boundary out of max_io_len so that the discard
support can make use of it without duplicating max_io_len code.
Avoiding max_io_len's split_io logic enables DM's discard support to
submit the entire discard request to a target. But discards must still
be split on target boundaries.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allow discards to be passed through to linear mappings if at least one
underlying device supports it. Discards will be forwarded only to
devices that support them.
A target that supports discards should set num_discard_requests to
indicate how many times each discard request must be submitted to it.
Verify table's underlying devices support discards prior to setting the
associated DM device as capable of discards (via QUEUE_FLAG_DISCARD).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add devname:mapper/control and MAPPER_CTRL_MINOR module alias
to support dm-mod module autoloading.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
'target_request_nr' is a more generic name that reflects the fact that
it will be used for both flush and discard support.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Determine whether a mapped device is bio-based or request-based when
loading its first (inactive) table and don't allow that to be changed
later.
This patch performs different device initialisation in each of the two
cases. (We don't think it's necessary to add code to support changing
between the two types.)
Allowed md->type transitions:
DM_TYPE_NONE to DM_TYPE_BIO_BASED
DM_TYPE_NONE to DM_TYPE_REQUEST_BASED
We now prevent table_load from replacing the inactive table with a
conflicting type of table even after an explicit table_clear.
Introduce 'type_lock' into the struct mapped_device to protect md->type
and to prepare for the next patch that will change the queue
initialization and allocate memory while md->type_lock is held.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
drivers/md/dm-ioctl.c | 15 +++++++++++++++
drivers/md/dm.c | 37 ++++++++++++++++++++++++++++++-------
drivers/md/dm.h | 5 +++++
include/linux/dm-ioctl.h | 4 ++--
4 files changed, 52 insertions(+), 9 deletions(-)
nouveau starting using these APIs, the first on non-x86 hw, and this
include isn't required on anything with real amounts of vmalloc space.
this fixes a build problem on powerpc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
We don't actually need this include on any platform.
built on powerpc + x86, reported on m68k.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
isofs: Fix lseek() to position beyond 4 GB
vfs: remove unused MNT_STRICTATIME
vfs: show unreachable paths in getcwd and proc
vfs: only add " (deleted)" where necessary
vfs: add prepend_path() helper
vfs: __d_path: dont prepend the name of the root dentry
ia64: perfmon: add d_dname method
vfs: add helpers to get root and pwd
cachefiles: use path_get instead of lone dget
fs/sysv/super.c: add support for non-PDP11 v7 filesystems
V7: Adjust sanity checks for some volumes
Add v7 alias
v9fs: fixup for inode_setattr being removed
Manual merge to take Al's version of the fs/sysv/super.c file: it merged
cleanly, but Al had removed an unnecessary header include, so his side
was better.
Add multiplexed bus core support. I2C multiplexer and switches
like pca954x get instantiated as new adapters per port.
Signed-off-by: Michael Lawnick <ml.lawnick@gmx.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Moving userspace-instantiated clients to separate lists wasn't nearly
enough to avoid deadlocks in multiplexed bus cases. We also want to
have a dedicated mutex to protect each list.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
Uninline i2c adapter locking helper functions, move them to i2c-core,
and use them in i2c-core itself. The functions are still exported for
external users. This makes future updates to the locking model (which
will be needed for multiplexing support) possible and transparent.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
Now that i2c-core offers the possibility to provide custom probing
function for I2C devices, let's make use of it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The probe method used by i2c_new_probed_device() may not be suitable
for all cases. Let the caller provide its own, optional probe
function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (226 commits)
ARM: 6323/1: cam60: don't use __init for cam60_spi_{flash_platform_data,partitions}
ARM: 6324/1: cam60: move cam60_spi_devices to .init.data
ARM: 6322/1: imx/pca100: Fix name of spi platform data
ARM: 6321/1: fix syntax error in main Kconfig file
ARM: 6297/1: move U300 timer to dynamic clock lookup
ARM: 6296/1: clock U300 intcon and timer properly
ARM: 6295/1: fix U300 apb_pclk split
ARM: 6306/1: fix inverted MMC card detect in U300
ARM: 6299/1: errata: TLBIASIDIS and TLBIMVAIS operations can broadcast a faulty ASID
ARM: 6294/1: etm: do a dummy read from OSSRR during initialization
ARM: 6292/1: coresight: add ETM management registers
ARM: 6288/1: ftrace: document mcount formats
ARM: 6287/1: ftrace: clean up mcount assembly indentation
ARM: 6286/1: fix Thumb-2 decompressor broken by "Auto calculate ZRELADDR"
ARM: 6281/1: video/imxfb.c: allow usage without BACKLIGHT_CLASS_DEVICE
ARM: 6280/1: imx: Fix build failure when including <mach/gpio.h> without <linux/spinlock.h>
ARM: S5PV210: Fix on missing s3c-sdhci card detection method for hsmmc3
ARM: S5P: Fix on missing S5P_DEV_FIMC in plat-s5p/Kconfig
ARM: S5PV210: Override FIMC driver name on Aquila board
ARM: S5PC100: enable FIMC on SMDKC100
...
Fix up conflicts in arch/arm/mach-{s5pc100,s5pv210}/cpu.c due to
different subsystem 'setname' calls, and trivial port types in
include/linux/serial_core.h
Simply replace the whole kfifo.c and kfifo.h files with the new generic
version and fix the kerneldoc API template file.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the new version of the kfifo API files kfifo.c and kfifo.h.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For consistency with other kfifo routines, return bool, not int.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Newly mkfs-ed filesystems from Seventh Edition have last modification time
set to zero, but are otherwise perfectly valid.
Also, tighten up other sanity checks to filter out most filesystems with
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We are missing the oops end marker for the exception based WARN implementation
in lib/bug.c. This is useful for logfile analysis tools.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To keep panic_timeout accuracy when running under a hypervisor, the
current implementation only spins on long time (1 second) calls to mdelay.
That brings a good effect, but the problem is the keyboard LEDs don't
blink at all on that situation.
This patch changes to call to panic_blink_enter() between every mdelay and
keeps blinking in spite of long spin timer mode.
The time to call to mdelay is now 100ms. Even this change will keep
panic_timeout accuracy enough when running under a hypervisor.
Signed-off-by: TAMUKI Shoichi <tamuki@linet.gr.jp>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Architectures implement dma_is_consistent() in different ways (some
misinterpret the definition of API in DMA-API.txt). So it hasn't been so
useful for drivers. We have only one user of the API in tree. Unlikely
out-of-tree drivers use the API.
Even if we fix dma_is_consistent() in some architectures, it doesn't look
useful at all. It was invented long ago for some old systems that can't
allocate coherent memory at all. It's better to export only APIs that are
definitely necessary for drivers.
Let's remove this API.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_get_cache_alignment returns the minimum DMA alignment. Architectures
defines it as ARCH_DMA_MINALIGN (formally ARCH_KMALLOC_MINALIGN). So we
can unify dma_get_cache_alignment implementations.
Note that some architectures implement dma_get_cache_alignment wrongly.
dma_get_cache_alignment() should return the minimum DMA alignment. So
fully-coherent architectures should return 1. This patch also fixes this
issue.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now each architecture has the own dma_get_cache_alignment implementation.
dma_get_cache_alignment returns the minimum DMA alignment. Architectures
define it as ARCH_KMALLOC_MINALIGN (it's used to make sure that malloc'ed
buffer is DMA-safe; the buffer doesn't share a cache with the others). So
we can unify dma_get_cache_alignment implementations.
This patch:
dma_get_cache_alignment() needs to know if an architecture defines
ARCH_KMALLOC_MINALIGN or not (needs to know if architecture has DMA
alignment restriction). However, slab.h define ARCH_KMALLOC_MINALIGN if
architectures doesn't define it.
Let's rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN.
ARCH_KMALLOC_MINALIGN is used only in the internals of slab/slob/slub
(except for crypto).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mem_cgroup_soft_limit_reclaim() has zone, nid and zid argument. but nid
and zid can be calculated from zone. So remove it.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Nishimura Daisuke <d-nishimura@mtf.biglobe.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently mem_cgroup_shrink_node_zone() call shrink_zone() directly. thus
it doesn't need to initialize sc.nodemask because shrink_zone() doesn't
use it at all.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Nishimura Daisuke <d-nishimura@mtf.biglobe.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the OOM killer scans task, it check a task is under memcg or
not when it's called via memcg's context.
But, as Oleg pointed out, a thread group leader may have NULL ->mm
and task_in_mem_cgroup() may do wrong decision. We have to use
find_lock_task_mm() in memcg as generic OOM-Killer does.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The gpios on the max730x chips have support for internal pullups while in
input mode.
This patch adds support for configuring these pullups via platform data.
A new member ("input_pullup_active") to the platform data struct is
introduced. A set bit in this variable activates the pullups while the
respective port is in input mode. This is a compatible enhancement since
unset bits lead to disables pullups which was the default in the original
driver.
_Note_: the 4 lowest bits in "input_pullup_active" are unused because the
first 4 ports of the controller are not used, too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are some chips (like TI WL12xx series) that can be interfaced over
SDIO but don't support the SDIO specification, meaning that they are
missing CIA (Common I/O Area) with all it's registers. Current Linux SDIO
implementation relies on those registers to identify and configure the
card, so non-standard cards can not function and cause lots of warnings
from the core when it reads invalid data from non-existent registers.
After this patch, init_card() host callback can now set new quirk
MMC_QUIRK_NONSTD_SDIO, which means that SDIO core should not try to access
any standard SDIO registers and rely on init_card() to fill all SDIO
structures instead. As those cards are usually embedded chips, all the
required information can be obtained from machine board files by the host
driver when it's called through init_card() callback.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Kalle Valo <kvalo@adurom.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If you don't use CONFIG_MMC_UNSAFE_RESUME, as soon as you attempt to
suspend, the card will be removed, therefore this patch doesn't change the
behavior of this option.
However the removal will be done by pm notifier, which runs while
userspace is still not frozen and thus can freely use del_gendisk, without
the risk of deadlock which would happen otherwise.
Card detect workqueue is now disabled while userspace is frozen, Therefore
if you do use CONFIG_MMC_UNSAFE_RESUME, and remove the card during
suspend, the removal will be detected as soon as userspace is unfrozen,
again at the moment it is safe to call del_gendisk.
Tested with and without CONFIG_MMC_UNSAFE_RESUME with suspend and hibernate.
[akpm@linux-foundation.org: clean up function prototype]
[akpm@linux-foundation.org: fix CONFIG_PM-n linkage, small cleanups]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The eMMC spec 4.4 and 4.3 + additional feature chips has CSD structure
version 3 and version 3 have to check the CSD_STRUCTURE byte in the
EXT_CSD register.
Also fix EXT_CSD revision message.
[akpm@linux-foundation.org: fix comment, per Chris Ball]
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The O_* bit numbers are defined in 20+ arch/*, and can silently overlap.
Add a compile time check to ensure the uniqueness as suggested by David
Miller.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: David Miller <davem@davemloft.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Jamie Lokier <jamie@shareable.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add <linux/types.h> to <linux/virtio_9p.h> so that types are explicitly
defined:
linux/virtio_9p.h:15: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 9e4f5e29 ("FC Pass Thru support") exported a number of header files
in include/scsi to user space, but didn't change the uX types to the
userspace-compatible __uX types. Without that you'll get compile errors
when including them - E.G.:
include/scsi/scsi.h:145: error: expected specifier-qualifier-list before `u8'
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Smart <james.smart@emulex.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One straggler which was missed due to merge ordering issues.
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Eric Paris <eparis@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc allows this when arg is a function, but sparse complains:
drivers/char/ipmi/ipmi_watchdog.c:303:1: error: cannot dereference this type
drivers/char/ipmi/ipmi_watchdog.c:307:1: error: cannot dereference this type
drivers/char/ipmi/ipmi_watchdog.c:311:1: error: cannot dereference this type
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Also reorders the macros with the most common ones at the top.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
There may be cases (most obviously, sysfs-writable charp parameters) where
a module needs to prevent sysfs access to parameters.
Rather than express this in terms of a big lock, the functions are
expressed in terms of what they protect against. This is clearer, esp.
if the implementation changes to a module-level or even param-level lock.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Since this section can be read-only (they're in .rodata), they should
always have been const. Minor flow-through various functions.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
This allows us to generalize the KPARAM_KMALLOCED flag, by calling a function
on every parameter when a module is unloaded.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
This is more kernel-ish, saves some space, and also allows us to
expand the ops without breaking all the callers who are happy for the
new members to be NULL.
The few places which defined their own param types are changed to the
new scheme (more which crept in recently fixed in following patches).
Since we're touching them anyway, we change get() and set() to take a
const struct kernel_param (which they really are). This causes some
harmless warnings until we fix them (in following patches).
To reduce churn, module_param_call creates the ops struct so the callers
don't have to change (and casts the functions to reduce warnings).
The modern version which takes an ops struct is called module_param_cb.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Alessandro Rubini <rubini@ipvvis.unipv.it>
Cc: Michal Januszewski <spock@gentoo.org>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-fbdev-devel@lists.sourceforge.net
Cc: linux-nfs@vger.kernel.org
Cc: netdev@vger.kernel.org
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds voltage regulator driver for Maxim 8998 chip. This chip
is used on Samsung Aquila and GONI boards and provides following
functionalities:
- 4 BUCK voltage converters, 17 LDO power regulators and 5 other power
controllers
- battery charger
This patch adds basic driver for voltage regulators and MAX 8998 MFD core.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If error hugepage is not in-use, we can fully recovery from error
by dequeuing it from freelist, so return RECOVERY.
Otherwise whether or not we can recovery depends on user processes,
so return DELAYED.
Dependency:
"HWPOISON, hugetlb: enable error handling path for hugepage"
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
This patch adds reverse mapping feature for hugepage by introducing
mapcount for shared/private-mapped hugepage and anon_vma for
private-mapped hugepage.
While hugepage is not currently swappable, reverse mapping can be useful
for memory error handler.
Without this patch, memory error handler cannot identify processes
using the bad hugepage nor unmap it from them. That is:
- for shared hugepage:
we can collect processes using a hugepage through pagecache,
but can not unmap the hugepage because of the lack of mapcount.
- for privately mapped hugepage:
we can neither collect processes nor unmap the hugepage.
This patch solves these problems.
This patch include the bug fix given by commit 23be7468e8, so reverts it.
Dependency:
"hugetlb: move definition of is_vm_hugetlb_page() to hugepage_inline.h"
ChangeLog since May 24.
- create hugetlb_inline.h and move is_vm_hugetlb_index() in it.
- move functions setting up anon_vma for hugepage into mm/rmap.c.
ChangeLog since May 13.
- rebased to 2.6.34
- fix logic error (in case that private mapping and shared mapping coexist)
- move is_vm_hugetlb_page() into include/linux/mm.h to use this function
from linear_page_index()
- define and use linear_hugepage_index() instead of compound_order()
- use page_move_anon_rmap() in hugetlb_cow()
- copy exclusive switch of __set_page_anon_rmap() into hugepage counterpart.
- revert commit 24be7468 completely
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Acked-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
is_vm_hugetlb_page() is a widely used inline function to insert hooks
into hugetlb code.
But we can't use it in pagemap.h because of circular dependency of
the header files. This patch removes this limitation.
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Commit d0adde574b added MNT_STRICTATIME
but it isn't actually used (MS_STRICTATIME clears MNT_RELATIME and
MNT_NOATIME rather than setting any mount flag).
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Prepend "(unreachable)" to path strings if the path is not reachable
from the current root.
Two places updated are
- the return string from getcwd()
- and symlinks under /proc/$PID.
Other uses of d_path() are left unchanged (we know that some old
software crashes if /proc/mounts is changed).
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add three helpers that retrieve a refcounted copy of the root and cwd
from the supplied fs_struct.
get_fs_root()
get_fs_pwd()
get_fs_root_and_pwd()
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Newly mkfs-ed filesystems from Seventh Edition have last modification
time set to zero, but are otherwise perfectly valid.
Also, tighten up other sanity checks to filter out most filesystems with
different bytesex than we're using.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
"netpoll: Use 'bool' for netpoll_rx() return type." missed the case when
CONFIG_NETPOLL is disabled.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warnings in linux/i2c.h:
Warning(include/linux/i2c.h:176): No description found for parameter 'alert'
Warning(include/linux/i2c.h:259): No description found for parameter 'of_node'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (94 commits)
V4L/DVB: tvp7002: fix write to H-PLL Feedback Divider LSB register
V4L/DVB: dvb: siano: free spinlock before schedule()
V4L/DVB: media: video: pvrusb2: remove custom hex_to_bin()
V4L/DVB: drivers: usbvideo: remove custom implementation of hex_to_bin()
V4L/DVB: Report supported QAM modes on bt8xx
V4L/DVB: media: ir-keytable: null dereference in debug code
V4L/DVB: ivtv: convert to the new control framework
V4L/DVB: ivtv: convert gpio subdev to new control framework
V4L/DVB: wm8739: convert to the new control framework
V4L/DVB: cs53l32a: convert to new control framework
V4L/DVB: wm8775: convert to the new control framework
V4L/DVB: cx2341x: convert to the control framework
V4L/DVB: cx25840: convert to the new control framework
V4L/DVB: cx25840/ivtv: replace ugly priv control with s_config
V4L/DVB: saa717x: convert to the new control framework
V4L/DVB: msp3400: convert to the new control framework
V4L/DVB: saa7115: convert to the new control framework
V4L/DVB: v4l2: hook up the new control framework into the core framework
V4L/DVB: Documentation: add v4l2-controls.txt documenting the new controls API
V4L/DVB: v4l2-ctrls: Whitespace cleanups
...
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
watchdog: hpwdt: formatting of pointers in printk()
watchdog: Adding support for ARM Primecell SP805 Watchdog
watchdog: f71808e_wdt: new watchdog driver for Fintek F71808E and F71882FG
watchdog: sch311x_wdt.c: set parent before registeriing the misc device in probe() function
watchdog: wdt_pci.c: move ids to pci_ids.h
watchdog: s3c2410_wdt - Fix removing of platform device
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - add USB-ID for PL-3601 Xbox 360 pad
Input: cy8ctmg100_ts - signedness bug
Input: elantech - report position also with 3 fingers
Input: elantech - discard the first 2 positions on some firmwares
Input: adxl34x - do not mark device as disabled on startup
Input: gpio_keys - add hooks to enable/disable device
Input: evdev - rearrange ioctl handling
Input: dynamically allocate ABS information
Input: switch to input_abs_*() access functions
Input: add static inline accessors for ABS properties
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (68 commits)
U6715 16550A serial driver support
Char: nozomi, set tty->driver_data appropriately
Char: nozomi, fix tty->count counting
serial: max3107: Fix gpiolib support
hsu: call PCI pm hooks in suspend/resume function
hsu: some code cleanup
hsu: add a periodic timer to check dma rx channel
hsu: driver for Medfield High Speed UART device
mxser: remove unnesesary NULL check
serial: add support for OX16PCI958 card
serial: 68328serial.c: remove dead (ALMA_ANS | DRAGONIXVZ | M68EZ328ADS)
timbuart: use __devinit and __devexit macros for probe and remove
serial: MMIO32 support for 8250_early.c
serial: mcf: don't take spinlocks in already protected functions
serial: general fixes in the serial_rs485 structure
serial: fix missing bit coverage of ASYNC_FLAGS
serial: "altera_uart: simplify altera_uart_console_putc()" checkpatch fixes
serial: crisv10: formatting of pointers in printk()
vt: Fix warning: statement with no effect due to vt_kern.h
tty_io: remove casts from void*
...
Fix kernel-doc warnings in linux/usb.h:
Warning(include/linux/usb.h:185): No description found for parameter 'resetting_device'
Warning(include/linux/usb.h:1212): No description found for parameter 'stream_id'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Logitech Harmony 700 series needs an extra delay during
initialization. This patch adds a USB quirk which enables such a delay
and adds the device to the quirks list.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1) Introduce ulpi specific flags for control of the ulpi phy
2) Extend the generic ulpi driver with support for Function and
Interface control of upli phy
3) Update the platforms using the generic ulpi driver with new ulpi
flags
4) Remove the otg control flags not in use
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes below compilation warning from ulpi.h
include/linux/usb/ulpi.h:145:
warning: 'struct otg_io_access_ops' declared inside parameter list
include/linux/usb/ulpi.h:145:
warning: its scope is only this definition or declaration,
which is probably not what you want
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1395) adds code to hcd_pci_suspend() for handling wakeup
races. This is another general race pattern, similar to the "open
vs. unregister" race we're all familiar with. Here, the race is
between suspending a device and receiving a wakeup request from one of
the device's suspended children.
In particular, if a root-hub wakeup is requested at about the same
time as the corresponding USB controller is suspended, and if the
controller is enabled for wakeup, then the controller should either
fail to suspend or else wake right back up again.
During system sleep this won't happen very much, especially since host
controllers generally aren't enabled for wakeup during sleep. However
it is definitely an issue for runtime PM. Something like this will be
needed to prevent the controller from autosuspending while waiting for
a root-hub resume to take place. (That is, in fact, the common case,
for which there is an extra test.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1385) adds a "do_wakeup" parameter to the pci_suspend
method used by PCI-based host controller drivers. ehci-hcd in
particular needs to know whether or not to enable wakeup when
suspending a controller. Although that information is currently
available through device_may_wakeup(), when support is added for
runtime suspend this will no longer be true.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1393) converts several of the single-bit fields in
struct usb_hcd to atomic flags. This is for safety's sake; not all
CPUs can update bitfield values atomically, and these flags are used
in multiple contexts.
The flag fields that are set only during registration or removal can
remain as they are, since non-atomic accesses at those times will not
cause any problems.
(Strictly speaking, the authorized_default flag should become atomic
as well. I didn't bother with it because it gets changed only via
sysfs. It can be done later, if anyone wants.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added a disconnect() callback to composite devices which
is called by composite glue when its disconnect callback
is called by gadget.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_string_ids_tab() and usb_string_ids_n() functions added to
the composite framework. The first accepts an array of
usb_string object and for each registeres a string id and the
second registeres a given number of ids and returns the first.
This may simplify string ids registration since gadgets and
composite functions won't have to call usb_string_id() several
times and each time check for errer status -- all this will be
done with a single call.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
FunctionFS had a bit unique name for function used to add it
to USB configuration. Renamed as to match naming convention
of other functions.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
And audit all the users. None needed the BKL. That was easy
because there was only very few around.
Tested with allmodconfig build on x86-64
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
From: Andi Kleen <ak@linux.intel.com>
With this patch, the LPM capable EHCI host controller can put device
into L1 sleep state which is a mode that can enter/exit quickly, and
reduce power consumption.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EHCI 1.1 addendum introduced several energy efficiency extensions for
EHCI USB host controllers:
1. LPM (link power management)
2. Per-port change
3. Shorter periodic frame list
4. Hardware prefetching
This patch is intended to define the HW bits and debug interface for
EHCI 1.1 addendum. The LPM and Per-port change patches will be sent out
after this patch.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
otg_io_write() function does not follow the declaration of
struct otg_io_access_ops.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1390) fixes a problem that crops up when a UHCI host
controller is unbound from uhci-hcd while there are still some active
URBs. The URBs have to be unlinked when the root hub is unregistered,
and uhci-hcd relies upon root-hub status polls as part of its
unlinking procedure. But usb_hcd_poll_rh_status() won't make those
status calls if hcd->rh_registered is clear, and the flag is cleared
_before_ the unregistration takes place.
Since hcd->rh_registered is used for other things and needs to be
cleared early, the solution is to add a new flag (rh_pollable) and use
it instead. It gets cleared _after_ the root hub is unregistered.
Now that the status polls don't end too soon, we have to make sure
they also don't occur too late -- after the root hub's usb_device
structure or the HCD's private structures are deallocated. Therefore
the patch adds usb_get_device() and usb_put_device() calls to protect
the root hub structure, and it adds an extra del_timer_sync() to
prevent the root-hub timer from causing an unexpected status poll.
This additional complexity would not be needed if the HCD framework
had provided separate stop() and release() callbacks instead of just
stop(). This lack could be fixed at some future time (although it
would require changes to every host controller driver); when that
happens this patch won't be needed any more.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
UART Features extract from STEricsson U6715 data-sheet (arm926 SoC for mobile phone):
* Fully compatible with industry standard 16C550 and 16C450 from various
manufacturers
* RX and TX 64 byte FIFO reduces CPU interrupts
* Full double buffering
* Modem control signals include CTS, RTS, (and DSR, DTR on UART1 only)
* Automatic baud rate selection
* Manual or automatic RTS/CTS smart hardware flow control
* Programmable serial characteristics:
– Baud rate generation (50 to 3.25M baud)
– 5, 6, 7 or 8-bit characters
– Even, odd or no-parity bit generation and detection
– 1, 1.5 or 2 stop bit generation
* Independent control of transmit, receive, line status, data set interrupts and FIFOs
* Full status-reporting capabilities
* Separate DMA signaling for RX and TX
* Timed interrupt to spread receive interrupt on known duration
* DMA time-out interrupt to allow detection of end of reception
* Carkit pulse coding and decoding compliant with USB carkit control interface [40]
In 16550A auto-configuration, if the fifo size is 64 then it's an U6 16550A port
Add set_termios hook & export serial8250_do_set_termios to change uart
clock following baudrate
Signed-off-by: Philippe Langlais <philippe.langlais@stericsson.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a PCI & UART driver, which suppors both PIO and DMA mode
UART operation. It has 3 identical UART ports and one internal
DMA controller.
Current FW will export 4 pci devices for hsu: 3 uart ports and 1
dma controller, each has one IRQ line. And we need to discuss the
device model, one PCI device covering whole HSU should be a better
model, but there is a problem of how to export the 4 IRQs info
Current driver set the highest baud rate to 2746800bps, which is
easy to scale down to 115200/230400.... To suport higher baud rate,
we need add special process, change DLAB/DLH/PS/DIV/MUL registers
all together.
921600 is the highest baud rate that has been tested with Bluetooth
modem connected to HSU port 0. Will test more when there is right
BT firmware.
Current version contains several work around for A0's Silicon bugs
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix several issues related to the RS485 interface:
- It adds the flag SER_RS485_RTS_BEFORE_SEND that was missing from the
serial_rs485 structure (even if "delay_rts_before_send" was existing)
- It adds a further "delay_rts_after_send" field for those drivers that
can have a delay after send (e.g., atmel_serial)
- It fixes the usage of the structure in the atmel_serial driver (where
"delay_rts_before_send" should be used instead of "delay_rts_after_send").
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Bernhard Roth <br@pwrnet.de>
Cc: Philippe De Muyter <phdm@macqel.be>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It seems that currently ASYNC_FLAGS is one bit short of covering all the
bits of the ASYNC user flags. In particular it does not cover the
ASYNC_AUTOPROBE bit.
ASYNCB_LAST_USER and ASYNCB_AUTOPROBE are both equal to 15.
Therefore:
ASYNC_AUTOPROBE = 1000 0000 0000 0000
ASYNC_FLAGS = 0111 1111 1111 1111
So ASYNC_FLAGS is not covering the ASYNC_AUTOPROBE bit.
This patch fixes the issue and with the patch the values will be:
ASYNC_AUTOPROBE = 1000 0000 0000 0000
ASYNC_FLAGS = 1111 1111 1111 1111
As a side note, doing a "git grep" I didn't find any use of
ASYNC_AUTOPROBE or ASYNCB_AUTOPROBE in the kernel, besides this include
file.
Signed-off-by: John Villalovos <john.l.villalovos@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using:
gcc (GCC) 4.5.0 20100610 (prerelease)
with CONFIG_CONSOLE_TRANSLATIONS=n, the following warnings are seen:
drivers/char/vt_ioctl.c: In function ‘vt_ioctl’:
drivers/char/vt_ioctl.c:1309:4: warning: statement with no effect
drivers/char/vt.c: In function ‘vc_allocate’:
drivers/char/vt.c:774:3: warning: statement with no effect
drivers/video/console/vgacon.c: In function ‘vgacon_init’:
drivers/video/console/vgacon.c:587:3: warning: statement with no effect
drivers/video/console/vgacon.c: In function ‘vgacon_deinit’:
drivers/video/console/vgacon.c:606:2: warning: statement with no effect
drivers/video/console/fbcon.c: In function ‘fbcon_init’:
drivers/video/console/fbcon.c:1087:3: warning: statement with no effect
drivers/video/console/fbcon.c:1089:3: warning: statement with no effect
drivers/video/console/fbcon.c: In function ‘fbcon_set_disp’:
drivers/video/console/fbcon.c:1369:3: warning: statement with no effect
drivers/video/console/fbcon.c:1371:3: warning: statement with no effect
This is because several functions in include/linux/vt_kern.h are
defined to (0). Convert them to static inline functions to
silence the warnings and gain a bit of type safety.
Signed-off-by: Kevin Winchester <kjwinchester@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At the moment there is only one platform type supported and there is is
hard wired, but with these changes the infrastructure is now there for
anyone else to provide methods for their hardware.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The tty locking now follows the rules for mutexes, so
we can replace the BKL usage with a new subsystem
wide mutex.
Using a regular mutex here will change the behaviour
when blocked on the BTM from spinning to sleeping,
but that should not be visible to the user.
Using the mutex also means that all the BTM is now
covered by lockdep.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This changes all remaining users of tty_lock_nested
to be non-recursive, which lets us kill this function.
As a consequence, we won't need to keep the lock count
any more, which allows more simplifications later.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Calling wait_event_interruptible implicitly
releases the BKL when it sleeps, but we need
to do this explcitly when we have converted
it to a mutex.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As a preparation for replacing the big kernel lock
in the TTY layer, wrap all the callers in new
macros tty_lock, tty_lock_nested and tty_unlock.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This takes all the tty references through the expected interface points so
we can refcount them.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The vt layer isn't safely handling reference counts to tty object on the input
side. Add a tty port structure to the vt layer in order to implement this using
the standard helpers.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pass down the ldisc number so that the drivers don't have to peek into the
tty object themselves. This lets us get rid of another case of back referencing
port to tty which we don't want (because of races versus hangup/close).
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This lets us avoid problems with races on the flag changes
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jesse's initial patch commit said:
"At panic time (i.e. when oops_in_progress is set) we should try a bit
harder to update the screen and make sure output gets to the VT, since
some drivers are capable of flipping back to it.
So make sure we try to unblank and update the display if called from a
panic context."
I've enhanced this to add a flag to the vc that console layer can set to
indicate they want this behaviour to occur. This also adds support to
fbcon for that flag and adds an fb flag for drivers to indicate they want
to use the support. It enables this for KMS drivers.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: James Simmons <jsimmons@infradead.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is against the 2.6.34 source.
Paraphrased from the 1989 BSD patch by David Borman @ cray.com:
These are the changes needed for the kernel to support
LINEMODE in the server.
There is a new bit in the termios local flag word, EXTPROC.
When this bit is set, several aspects of the terminal driver
are disabled. Input line editing, character echo, and mapping
of signals are all disabled. This allows the telnetd to turn
off these functions when in linemode, but still keep track of
what state the user wants the terminal to be in.
New ioctl:
TIOCSIG Generate a signal to processes in the
current process group of the pty.
There is a new mode for packet driver, the TIOCPKT_IOCTL bit.
When packet mode is turned on in the pty, and the EXTPROC bit
is set, then whenever the state of the pty is changed, the
next read on the master side of the pty will have the TIOCPKT_IOCTL
bit set. This allows the process on the server side of the pty
to know when the state of the terminal has changed; it can then
issue the appropriate ioctl to retrieve the new state.
Since the original BSD patches accompanied the source code for telnet
I've left that reference here, but obviously the feature is useful for
any remote terminal protocol, including ssh.
The corresponding feature has existed in the BSD tty driver since 1989.
For historical reference, a good copy of the relevant files can be found
here:
http://anonsvn.mit.edu/viewvc/krb5/trunk/src/appl/telnet/?pathrev=17741
Signed-off-by: Howard Chu <hyc@symas.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove Hayes ESP ioctls
The Hayes ESP driver has been removed from the tree:
commit f53a2ade0b
("tty: esp: remove broken driver")
so its ioctls aren't needed any more.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'writable_limits' of git://decibel.fi.muni.cz/~xslaby/linux:
unistd: add __NR_prlimit64 syscall numbers
rlimits: implement prlimit64 syscall
rlimits: switch more rlimit syscalls to do_prlimit
rlimits: redo do_setrlimit to more generic do_prlimit
rlimits: add rlimit64 structure
rlimits: do security check under task_lock
rlimits: allow setrlimit to non-current tasks
rlimits: split sys_setrlimit
rlimits: selinux, do rlimits changes under task_lock
rlimits: make sure ->rlim_max never grows in sys_setrlimit
rlimits: add task_struct to update_rlimit_cpu
rlimits: security, add task_struct to setrlimit
Fix up various system call number conflicts. We not only added fanotify
system calls in the meantime, but asm-generic/unistd.h added a wait4
along with a range of reserved per-architecture system calls.
* git://git.infradead.org/mtd-2.6: (79 commits)
mtd: Remove obsolete <mtd/compatmac.h> include
mtd: Update copyright notices
jffs2: Update copyright notices
mtd-physmap: add support users can assign the probe type in board files
mtd: remove redwood map driver
mxc_nand: Add v3 (i.MX51) Support
mxc_nand: support 8bit ecc
mxc_nand: fix correct_data function
mxc_nand: add V1_V2 namespace to registers
mxc_nand: factor out a check_int function
mxc_nand: make some internally used functions overwriteable
mxc_nand: rework get_dev_status
mxc_nand: remove 0xe00 offset from registers
mtd: denali: Add multi connected NAND support
mtd: denali: Remove set_ecc_config function
mtd: denali: Remove unuseful code in get_xx_nand_para functions
mtd: denali: Remove device_info_tag structure
mtd: m25p80: add support for the Winbond W25Q32 SPI flash chip
mtd: m25p80: add support for the Intel/Numonyx {16,32,64}0S33B SPI flash chips
mtd: m25p80: add support for the EON EN25P{32, 64} SPI flash chips
...
Fix up trivial conflicts in drivers/mtd/maps/{Kconfig,redwood.c} due to
redwood driver removal.
* 'for-linus' of git://git.infradead.org/users/eparis/notify: (132 commits)
fanotify: use both marks when possible
fsnotify: pass both the vfsmount mark and inode mark
fsnotify: walk the inode and vfsmount lists simultaneously
fsnotify: rework ignored mark flushing
fsnotify: remove global fsnotify groups lists
fsnotify: remove group->mask
fsnotify: remove the global masks
fsnotify: cleanup should_send_event
fanotify: use the mark in handler functions
audit: use the mark in handler functions
dnotify: use the mark in handler functions
inotify: use the mark in handler functions
fsnotify: send fsnotify_mark to groups in event handling functions
fsnotify: Exchange list heads instead of moving elements
fsnotify: srcu to protect read side of inode and vfsmount locks
fsnotify: use an explicit flag to indicate fsnotify_destroy_mark has been called
fsnotify: use _rcu functions for mark list traversal
fsnotify: place marks on object in order of group memory address
vfs/fsnotify: fsnotify_close can delay the final work in fput
fsnotify: store struct file not struct path
...
Fix up trivial delete/modify conflict in fs/notify/inotify/inotify.c.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (96 commits)
no need for list_for_each_entry_safe()/resetting with superblock list
Fix sget() race with failing mount
vfs: don't hold s_umount over close_bdev_exclusive() call
sysv: do not mark superblock dirty on remount
sysv: do not mark superblock dirty on mount
btrfs: remove junk sb_dirt change
BFS: clean up the superblock usage
AFFS: wait for sb synchronization when needed
AFFS: clean up dirty flag usage
cifs: truncate fallout
mbcache: fix shrinker function return value
mbcache: Remove unused features
add f_flags to struct statfs(64)
pass a struct path to vfs_statfs
update VFS documentation for method changes.
All filesystems that need invalidate_inode_buffers() are doing that explicitly
convert remaining ->clear_inode() to ->evict_inode()
Make ->drop_inode() just return whether inode needs to be dropped
fs/inode.c:clear_inode() is gone
fs/inode.c:evict() doesn't care about delete vs. non-delete paths now
...
Fix up trivial conflicts in fs/nilfs2/super.c
These form the basis of the basic WRITE etc primitives, so we
need them to be always visible. Otherwise we see errors like:
mm/filemap.c:2164: error: 'REQ_WRITE' undeclared
fs/read_write.c:362: error: 'REQ_WRITE' undeclared
fs/splice.c:1108: error: 'REQ_WRITE' undeclared
fs/aio.c:1496: error: 'REQ_WRITE' undeclared
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The previous value of 672 for L2CAP_DEFAULT_MAX_PDU_SIZE is based on
the default L2CAP MTU. That default MTU is calculated from the size
of two DH5 packets, minus ACL and L2CAP b-frame header overhead.
ERTM is used with newer basebands that typically support larger 3-DH5
packets, and i-frames and s-frames have more header overhead. With
clean RF conditions, basebands will typically attempt to use 1021-byte
3-DH5 packets for maximum throughput. Adjusting for 2 bytes of ACL
headers plus 10 bytes of worst-case L2CAP headers yields 1009 bytes
of payload.
This PDU size imposes less overhead for header bytes and gives the
baseband the option to choose 3-DH5 packets, but is small enough for
ERTM traffic to interleave well with other L2CAP or SCO data.
672-byte payloads do not allow the most efficient over-the-air
packet choice, and cannot achieve maximum throughput over BR/EDR.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The L2CAP specification requires that the ERTM retransmit timeout be at
least 2 seconds for BR/EDR connections.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add missing kernel-doc notation to struct sock:
Warning(include/net/sock.h:324): No description found for parameter 'sk_peer_pid'
Warning(include/net/sock.h:324): No description found for parameter 'sk_peer_cred'
Warning(include/net/sock.h:324): No description found for parameter 'sk_classid'
Warning(include/net/sock.h:324): Excess struct/union/enum/typedef member 'sk_peercred' description in 'sock'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix etherdevice.h parameter name typo in kernel-doc:
Warning(include/linux/etherdevice.h:138): No description found for parameter 'hwaddr'
Warning(include/linux/etherdevice.h:138): Excess function parameter 'addr' description in 'dev_hw_addr_random'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (59 commits)
igbvf.txt: Add igbvf Documentation
igb.txt: Add igb documentation
e100/e1000*/igb*/ixgb*: Add missing read memory barrier
ixgbe: fix build error with FCOE_CONFIG without DCB_CONFIG
netxen: protect tx timeout recovery by rtnl lock
isdn: gigaset: use after free
isdn: gigaset: add missing unlock
solos-pci: Fix race condition in tasklet RX handling
pkt_sched: Fix sch_sfq vs tcf_bind_filter oops
net: disable preemption before call smp_processor_id()
tcp: no md5sig option size check bug
iwlwifi: fix locking assertions
iwlwifi: fix TX tracer
isdn: fix information leak
net: Fix napi_gro_frags vs netpoll path
usbnet: remove noisy and hardly useful printk
rtl8180: avoid potential NULL deref in rtl8180_beacon_work
ath9k: Remove myself from the MAINTAINERS list
libertas: scan before assocation if no BSSID was given
libertas: fix association with some APs by using extended rates
...
Getting and putting arrays of pointers with flex arrays is a PITA. You
have to remember to pass &ptr to the _put and you have to do weird and
wacky casting to get the ptr back from the _get. Add two functions
flex_array_get_ptr() and flex_array_put_ptr() to handle all of the magic.
[akpm@linux-foundation.org: simplification suggested by Joe]
Signed-off-by: Eric Paris <eparis@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Joe Perches <joe@perches.com>
Cc: James Morris <jmorris@namei.org>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A profile of a network benchmark showed iommu_num_pages rather high up:
0.52% iommu_num_pages
Looking at the profile, an integer divide is taking almost all of the time:
%
: c000000000376ea4 <.iommu_num_pages>:
1.93 : c000000000376ea4: fb e1 ff f8 std r31,-8(r1)
0.00 : c000000000376ea8: f8 21 ff c1 stdu r1,-64(r1)
0.00 : c000000000376eac: 7c 3f 0b 78 mr r31,r1
3.86 : c000000000376eb0: 38 84 ff ff addi r4,r4,-1
0.00 : c000000000376eb4: 38 05 ff ff addi r0,r5,-1
0.00 : c000000000376eb8: 7c 84 2a 14 add r4,r4,r5
46.95 : c000000000376ebc: 7c 00 18 38 and r0,r0,r3
45.66 : c000000000376ec0: 7c 84 02 14 add r4,r4,r0
0.00 : c000000000376ec4: 7c 64 2b 92 divdu r3,r4,r5
0.00 : c000000000376ec8: 38 3f 00 40 addi r1,r31,64
0.00 : c000000000376ecc: eb e1 ff f8 ld r31,-8(r1)
1.61 : c000000000376ed0: 4e 80 00 20 blr
Since every caller of iommu_num_pages passes in a constant power of two
we can inline this such that the divide is replaced by a shift. The
entire function is only a few instructions once optimised, so it is
a good candidate for inlining overall.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are no more uses of NIPQUAD or NIPQUAD_FMT. Remove the definitions.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We should use the __same_type() helper in __must_be_array().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The asm-generic/iomap.h provides these functions already, but the
non-generic fallback defines do not.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some SoC chips, HW resources may be in use during any particular idle
period. As a consequence, the cpuidle states that the SoC is safe to
enter can change from idle period to idle period. In addition, the
latency and threshold of each cpuidle state can vary, depending on the
operating condition when the CPU becomes idle, e.g. the current cpu
frequency, the current state of the HW blocks, etc.
cpuidle core and the menu governor, in the current form, are geared
towards cpuidle states that are static, i.e. the availabiltiy of the
states, their latencies, their thresholds are non-changing during run
time. cpuidle does not provide any hook that cpuidle drivers can use to
adjust those values on the fly for the current idle period before the menu
governor selects the target cpuidle state.
This patch extends cpuidle core and the menu governor to handle states
that are dynamic. There are three additions in the patch and the patch
maintains backwards-compatibility with existing cpuidle drivers.
1) add prepare() to struct cpuidle_device. A cpuidle driver can hook
into the callback and cpuidle will call prepare() before calling the
governor's select function. The callback gives the cpuidle driver a
chance to update the dynamic information of the cpuidle states for the
current idle period, e.g. state availability, latencies, thresholds,
power values, etc.
2) add CPUIDLE_FLAG_IGNORE as one of the state flags. In the prepare()
function, a cpuidle driver can set/clear the flag to indicate to the
menu governor whether a cpuidle state should be ignored, i.e. not
available, during the current idle period.
3) add power_specified bit to struct cpuidle_device. The menu governor
currently assumes that the cpuidle states are arranged in the order of
increasing latency, threshold, and power savings. This is true or can
be made true for static states. Once the state parameters are dynamic,
the latencies, thresholds, and power savings for the cpuidle states can
increase or decrease by different amounts from idle period to idle
period. So the assumption of increasing latency, threshold, and power
savings from Cn to C(n+1) can no longer be guaranteed.
It can be straightforward to calculate the power consumption of each
available state and to specify it in power_usage for the idle period.
Using the power_usage fields, the menu governor then selects the state
that has the lowest power consumption and that still satisfies all other
critieria. The power_specified bit defaults to 0. For existing cpuidle
drivers, cpuidle detects that power_specified is 0 and fills in a dummy
set of power_usage values.
Signed-off-by: Ai Li <aili@codeaurora.org>
Cc: Len Brown <len.brown@intel.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When taking a memory snapshot in hibernate_snapshot(), all (directly
called) memory allocations use GFP_ATOMIC. Hence swap misusage during
hibernation never occurs.
But from a pessimistic point of view, there is no guarantee that no page
allcation has __GFP_WAIT. It is better to have a global indication "we
enter hibernation, don't use swap!".
This patch tries to freeze new-swap-allocation during hibernation. (All
user processes are frozenm so swapin is not a concern).
This way, no updates will happen to swap_map[] between
hibernate_snapshot() and save_image(). Swap is thawed when swsusp_free()
is called. We can be assured that swap corruption will not occur.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Hugh Dickins <hughd@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Ondrej Zary <linux@rainbow-software.org>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Memcg also need to trace page isolation information as global reclaim.
This patch does it.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman recently added some vmscan tracepoints. Unfortunately they are
covered only global reclaim. But we want to trace memcg reclaim too.
Thus, this patch convert them to DEFINE_TRACE macro. it help to reuse
tracepoint definition for other similar usage (i.e. memcg). This patch
have no functionally change.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Memcg also need to trace reclaim progress as direct reclaim. This patch
add it.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman recently added some vmscan tracepoints. Unfortunately they are
covered only global reclaim. But we want to trace memcg reclaim too.
Thus, this patch convert them to DEFINE_TRACE macro. it help to reuse
tracepoint definition for other similar usage (i.e. memcg). This patch
have no functionally change.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On swapin it is fairly common for a page to be owned exclusively by one
process. In that case we want to add the page to the anon_vma of that
process's VMA, instead of to the root anon_vma.
This will reduce the amount of rmap searching that the swapout code needs
to do.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
/proc/pid/oom_adj is now deprecated so that that it may eventually be
removed. The target date for removal is August 2012.
A warning will be printed to the kernel log if a task attempts to use this
interface. Future warning will be suppressed until the kernel is rebooted
to prevent spamming the kernel log.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This a complete rewrite of the oom killer's badness() heuristic which is
used to determine which task to kill in oom conditions. The goal is to
make it as simple and predictable as possible so the results are better
understood and we end up killing the task which will lead to the most
memory freeing while still respecting the fine-tuning from userspace.
Instead of basing the heuristic on mm->total_vm for each task, the task's
rss and swap space is used instead. This is a better indication of the
amount of memory that will be freeable if the oom killed task is chosen
and subsequently exits. This helps specifically in cases where KDE or
GNOME is chosen for oom kill on desktop systems instead of a memory
hogging task.
The baseline for the heuristic is a proportion of memory that each task is
currently using in memory plus swap compared to the amount of "allowable"
memory. "Allowable," in this sense, means the system-wide resources for
unconstrained oom conditions, the set of mempolicy nodes, the mems
attached to current's cpuset, or a memory controller's limit. The
proportion is given on a scale of 0 (never kill) to 1000 (always kill),
roughly meaning that if a task has a badness() score of 500 that the task
consumes approximately 50% of allowable memory resident in RAM or in swap
space.
The proportion is always relative to the amount of "allowable" memory and
not the total amount of RAM systemwide so that mempolicies and cpusets may
operate in isolation; they shall not need to know the true size of the
machine on which they are running if they are bound to a specific set of
nodes or mems, respectively.
Root tasks are given 3% extra memory just like __vm_enough_memory()
provides in LSMs. In the event of two tasks consuming similar amounts of
memory, it is generally better to save root's task.
Because of the change in the badness() heuristic's baseline, it is also
necessary to introduce a new user interface to tune it. It's not possible
to redefine the meaning of /proc/pid/oom_adj with a new scale since the
ABI cannot be changed for backward compatability. Instead, a new tunable,
/proc/pid/oom_score_adj, is added that ranges from -1000 to +1000. It may
be used to polarize the heuristic such that certain tasks are never
considered for oom kill while others may always be considered. The value
is added directly into the badness() score so a value of -500, for
example, means to discount 50% of its memory consumption in comparison to
other tasks either on the system, bound to the mempolicy, in the cpuset,
or sharing the same memory controller.
/proc/pid/oom_adj is changed so that its meaning is rescaled into the
units used by /proc/pid/oom_score_adj, and vice versa. Changing one of
these per-task tunables will rescale the value of the other to an
equivalent meaning. Although /proc/pid/oom_adj was originally defined as
a bitshift on the badness score, it now shares the same linear growth as
/proc/pid/oom_score_adj but with different granularity. This is required
so the ABI is not broken with userspace applications and allows oom_adj to
be deprecated for future removal.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since 2.6.28 zone->prev_priority is unused. Then it can be removed
safely. It reduce stack usage slightly.
Now I have to say that I'm sorry. 2 years ago, I thought prev_priority
can be integrate again, it's useful. but four (or more) times trying
haven't got good performance number. Thus I give up such approach.
The rest of this changelog is notes on prev_priority and why it existed in
the first place and why it might be not necessary any more. This information
is based heavily on discussions between Andrew Morton, Rik van Riel and
Kosaki Motohiro who is heavily quotes from.
Historically prev_priority was important because it determined when the VM
would start unmapping PTE pages. i.e. there are no balances of note within
the VM, Anon vs File and Mapped vs Unmapped. Without prev_priority, there
is a potential risk of unnecessarily increasing minor faults as a large
amount of read activity of use-once pages could push mapped pages to the
end of the LRU and get unmapped.
There is no proof this is still a problem but currently it is not considered
to be. Active files are not deactivated if the active file list is smaller
than the inactive list reducing the liklihood that file-mapped pages are
being pushed off the LRU and referenced executable pages are kept on the
active list to avoid them getting pushed out by read activity.
Even if it is a problem, prev_priority prev_priority wouldn't works
nowadays. First of all, current vmscan still a lot of UP centric code. it
expose some weakness on some dozens CPUs machine. I think we need more and
more improvement.
The problem is, current vmscan mix up per-system-pressure, per-zone-pressure
and per-task-pressure a bit. example, prev_priority try to boost priority to
other concurrent priority. but if the another task have mempolicy restriction,
it is unnecessary, but also makes wrong big latency and exceeding reclaim.
per-task based priority + prev_priority adjustment make the emulation of
per-system pressure. but it have two issue 1) too rough and brutal emulation
2) we need per-zone pressure, not per-system.
Another example, currently DEF_PRIORITY is 12. it mean the lru rotate about
2 cycle (1/4096 + 1/2048 + 1/1024 + .. + 1) before invoking OOM-Killer.
but if 10,0000 thrreads enter DEF_PRIORITY reclaim at the same time, the
system have higher memory pressure than priority==0 (1/4096*10,000 > 2).
prev_priority can't solve such multithreads workload issue. In other word,
prev_priority concept assume the sysmtem don't have lots threads."
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Michael Rubin <mrubin@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a trace event for when page reclaim queues a page for IO and records
whether it is synchronous or asynchronous. Excessive synchronous IO for a
process can result in noticeable stalls during direct reclaim. Excessive
IO from page reclaim may indicate that the system is seriously under
provisioned for the amount of dirty pages that exist.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Larry Woodman <lwoodman@redhat.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Michael Rubin <mrubin@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an event for when pages are isolated en-masse from the LRU lists.
This event augments the information available on LRU traffic and can be
used to evaluate lumpy reclaim.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Larry Woodman <lwoodman@redhat.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Michael Rubin <mrubin@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add two trace events for kswapd waking up and going asleep for the
purposes of tracking kswapd activity and two trace events for direct
reclaim beginning and ending. The information can be used to work out how
much time a process or the system is spending on the reclamation of pages
and in the case of direct reclaim, how many pages were reclaimed for that
process. High frequency triggering of these events could point to memory
pressure problems.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Larry Woodman <lwoodman@redhat.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Michael Rubin <mrubin@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We try to avoid livelocks of writeback when some steadily creates dirty
pages in a mapping we are writing out. For memory-cleaning writeback,
using nr_to_write works reasonably well but we cannot really use it for
data integrity writeback. This patch tries to solve the problem.
The idea is simple: Tag all pages that should be written back with a
special tag (TOWRITE) in the radix tree. This can be done rather quickly
and thus livelocks should not happen in practice. Then we start doing the
hard work of locking pages and sending them to disk only for those pages
that have TOWRITE tag set.
Note: Adding new radix tree tag grows radix tree node from 288 to 296
bytes for 32-bit archs and from 552 to 560 bytes for 64-bit archs.
However, the number of slab/slub items per page remains the same (13 and 7
respectively).
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement function for setting one tag if another tag is set for each item
in given range.
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new anon-vma code, was suboptimal and it lead to erratic invocation of
ksm_does_need_to_copy. That leads to host hangs or guest vnc lockup, or
weird behavior. It's unclear why ksm_does_need_to_copy is unstable but
the point is that when KSM is not in use, ksm_does_need_to_copy must never
run or we bounce pages for no good reason. I suspect the same hangs will
happen with KVM swaps. But this at least fixes the regression in the
new-anon-vma code and it only let KSM bugs triggers when KSM is in use.
The code in do_swap_page likely doesn't cope well with a not-swapcache,
especially the memcg code.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Izik Eidus <ieidus@yahoo.com>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current implementation of tmpfs is not scalable. We found that
stat_lock is contended by multiple threads when we need to get a new page,
leading to useless spinning inside this spin lock.
This patch makes use of the percpu_counter library to maintain local count
of used blocks to speed up getting and returning of pages. So the
acquisition of stat_lock is unnecessary for getting and returning blocks,
improving the performance of tmpfs on system with large number of cpus.
On a 4 socket 32 core NHM-EX system, we saw improvement of 270%.
The implementation below has a slight chance of race between threads
causing a slight overshoot of the maximum configured blocks. However, any
overshoot is small, and is bounded by the number of cpus. This happens
when the number of used blocks is slightly below the maximum configured
blocks when a thread checks the used block count, and another thread
allocates the last block before the current thread does. This should not
be a problem for tmpfs, as the overshoot is most likely to be a few blocks
and bounded. If a strict limit is really desired, then configured the max
blocks to be the limit less the number of cpus in system.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add percpu_counter_compare that allows for a quick but accurate comparison
of percpu_counter with a given value.
A rough count is provided by the count field in percpu_counter structure,
without accounting for the other values stored in individual cpu counters.
The actual count is a sum of count and the cpu counters. However, count
field is never different from the actual value by a factor of
batch*num_online_cpu. We do not need to get actual count for comparison
if count is different from the given value by this factor and allows for
quick comparison without summing up all the per cpu counters.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No real bugs, just some dead code and some fixups.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid quite a lot of warnings in header files in a gcc 4.6 -Wall builds
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define stubs for the numa_*_id() generic percpu related functions for
non-NUMA configurations in <asm-generic/topology.h> where the other
non-numa stubs live.
Fixes ia64 !NUMA build breakage -- e.g., tiger_defconfig
Back out now unneeded '#ifndef CONFIG_NUMA' guards from ia64 smpboot.c
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have been used naming try_set_zone_oom and clear_zonelist_oom.
The role of functions is to lock of zonelist for preventing parallel
OOM. So clear_zonelist_oom makes sense but try_set_zone_oome is rather
awkward and unmatched with clear_zonelist_oom.
Let's change it with try_set_zonelist_oom.
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: David Rientjes <rientjes@google.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>