IPv4 options are not very well aligned within the packet and the
format of a CIPSO option is even worse. The result is that the CIPSO
engine in the kernel does a few unaligned accesses when parsing and
validating incoming packets with CIPSO options attached which generate
error messages on certain alignment sensitive platforms. This patch
fixes this by marking these unaligned accesses with the
get_unaliagned() macro.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current NetLabel code has some redundant APIs which allow both
"struct socket" and "struct sock" types to be used; this may have made
sense at some point but it is wasteful now. Remove the functions that
operate on sockets and convert the callers. Not only does this make
the code smaller and more consistent but it pushes the locking burden
up to the caller which can be more intelligent about the locks. Also,
perform the same conversion (socket to sock) on the SELinux/NetLabel
glue code where it make sense.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we create idev before addresses are added, it no longer makes
sense to remove them when addresses are all deleted.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manuel Estrada Sainz passed away on May 9th 2004, his email account got
deactivated. He was in charge of the firmware_class code, and still got
CC'ed in recent discussions about it.
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to Jean Delvare <khali@linux-fr.org> for pointing it out to me.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CC drivers/base/dd.o
drivers/base/dd.c:211: warning: =E2=80=98device_probe_drivers=E2=80=99 defi=
ned but not used
Looks like the following is dead.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Class-devices created by "struct class_device" are going to be replaced
by "struct device". Keep the deprecated PHYSDEV* variables for the already
"deprecated" struct class_device" devices.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make note of the legacy "probe-the-hardware" drivers, and some APIs that
are mostly unused except by such drivers. We probably can't escape having
legacy drivers for a while (e.g. old ISA drivers), but we can at least
discourage this style code for new drivers, and unless it's unavoidable.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andres Salomon <dilinger@debian.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes CIFS honour a process' umask like other filesystems.
Of course the server is still free to munge the permissions if it wants
to; but the client will send the "right" permissions to begin with.
A few caveats:
1) It only applies to filesystems that have CAP_UNIX (aka support unix
extensions)
2) It applies the correct mode to the follow up CIFSSMBUnixSetPerms()
after remote creation
When mode to CIFS/NTFS ACL mapping is complete we can do the
same thing for that case for servers which do not
support the Unix Extensions.
Signed-off-by: Matt Keenen <matt@opcode-solutions.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Add the PATA controller device ID to pci_ids.h for MCP73/MCP77.
Signed-off-by: Peer Chen <peerchen@gmail.com>
Cc: Alan Cox <alan@redhat.com>,
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Eliminate UltraATA/133 support for HPT374 -- the chip isn't capable of this mode
according to the manual, and doesn't even seem to tolerate 66 MHz DPLL clock...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Geller Sandor <wildy@petra.hos.u-szeged.hu>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
generic IDE PCI driver, add another device exception
This device is char device and is grabbed by generic ide driver:
00:0b.0 Class ffff: National Semiconductor Corporation 87410 IDE (rev ff) (prog-if ff)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Disallow generic IDE PCI driver to grab it by adding next condition. Also
consolidate exceptions to one bigger 'switch (dev->vendor)'.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Ingo Korb <ml@akana.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Currently when system which have HPA require HPA to be detected and
disabled upon resume from RAM or disk. The current IDE drivers do not do
this nor does libata (obviously it since it doesn't support HPA yet).
I have implemented this into the current IDE drivers and it has been
tested by many others since 7/15/2006 in bug number 6840:
http://bugzilla.kernel.org/show_bug.cgi?id=6840
and it has been confirmed to work fine with no problems.
bart: added drv != NULL check to generic_ide_suspend()
From: Lee Trager <lt73@cs.drexel.edu>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The DMA support for RAID mode broke after:
commit 71ef51cc17
Author: Jens Axboe <axboe@suse.de>
Date: Â Fri Jul 28 09:02:17 2006 +0200
  [PATCH] it821x: fix ide dma setup bug
  Only enable dma for a valid speed setting.
  Signed-off-by: Jens Axboe <axboe@suse.de>
commit 0a8348d086
Author: Jens Axboe <axboe@suse.de>
Date: Â Fri Jul 28 08:58:26 2006 +0200
  [PATCH] ide: if the id fields looks screwy, disable DMA
  It's the safer choice. Originally due to a bug in itx821x, but a
  generally sound thing to do.
  Signed-off-by: Jens Axboe <axboe@suse.de>
However it worked by pure luck before Jens' fixes: bogus ide_dma_enable()
usage in it821x driver combined with loosy check in ide_dma_verbose() allowed
the hardware to operate in DMA mode. When these problems were fixed the DMA
support broke...
The source root for the regression turned out to be that the it821x.c code
was clearing too much of id->field_valid. The IDE core code was using the
original value of id->field_valid to do the tuning but later DMA got disabled
in ide_dma_verbose() because of the incorrect id->field_valid fixup. Fix it.
While at it:
* Do fixup() after probing the drives but before tuning them (which is also
OK w.r.t. ide_undecoded_slave() fixup). This change fixes device IDENTIFY
data to be consistent before/after the tuning and allows us to remove extra
re-tuning of drives from it821x_fixups().
* Fake MWDMA0 enabled/supported bits in IDENTIFY data if the device has
DMA capable bit set (this is just to tell the IDE core that DMA is
supported since it821x firmware takes care of DMA mode programming).
* Don't touch timing registers and don't program transfer modes on devices
et all when in RAID mode - depend solely on firmware to do the tuning
(as suggested by Alan Cox and done in libata pata_it821x driver).
Thanks for testing the patch goes out to Thomas Kuther.
Cc: Thomas Kuther <gimpel@sonnenkinder.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Problem noticed by Joe Zbiciak, see
http://kerneltrap.org/node/8252
for details.
On CSB6 the driver is using BIOS settings and not programming DMA/PIO timings
itself. However the logic was completely broken and resulted in wrong timings
being silently allowed (instead of being corrected by the driver).
This bug would explain some data corruption/timeout issues with Serverworks
MegaIDE in RAID mode that Alan Cox has fixed recently with:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=2074a106f52b6371885afbd714e929d60d0e3f64
For 2.6.23 we may be better off with completely switching the driver to always
programming timings (libata pata_serverworks.c driver is doing things this way
and there were no problems reported so far) but for 2.6.22 lets fix the bug
in the simplest and the least intrusive way.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove crappy code noticed by Linus, see
http://lkml.org/lkml/2007/5/23/476
for details.
While at it simplify logic a bit.
There should be no functionality changes caused by this patch.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch moves flexcop-dma (currently used only by flexcop-pci) to
b2c2-flexcop-pci module, that is dependent on CONFIG_PCI, fixing the bug
as reported by Geert Uytterhoeven <geert@linux-m68k.org>:
drivers/media/dvb/b2c2/flexcop-dma.c uses the PCI DMA API, but
DVB_B2C2_FLEXCOP doesn't depend on PCI, causing the following problem on
PCI-less systems:
| linux/drivers/media/dvb/b2c2/flexcop-dma.c:20: warning: implicit declaration of function 'pci_alloc_consistent'
| linux/drivers/media/dvb/b2c2/flexcop-dma.c:20: warning: implicit declaration of function 'pci_alloc_consistent'
Apparently this is the flexcop DMA core, which is used by both
DVB_B2C2_FLEXCOP_PCI and DVB_B2C2_FLEXCOP_USB.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Schimek requested the addition of inverted alpha framebuffer
caps/flags to support such hardware.
'Normal' alpha uses this formula to mix the framebuffer and video:
output = fb pixel * fb alpha + video pixel * (1 - fb alpha)
and the 'inverted' alpha uses this formula:
output = fb pixel * (1 - fb alpha) + video pixel * fb alpha
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The VIDIOC_CROPCAP ioctl was missing in ivtv.
The handling of output video cropping was wrong. This has now been fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L2_CAP_VIDEO_OUTPUT_POS was initially introduced for 2.6.22 but never
actually used: remove it before the final 2.6.22 is made.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- fixed the urb allocation part that was not taking into account the current alternate setting
this fixes usb_submit_urb returning -90 errno in isocIrq.
- fixed usb_submit_urb returning -1 errno in isocIrq (need to ignore usb urb with status==-ENOENT)
Acked-by: Dwaine P. Garden <dwainegarden@rogers.com>
Signed-off-by: Thierry Merle <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several people reported unreliable reception with the current driver.
Furthermore, STR and SNR values seem to be inverted.
This fix is based on a patch posted by Hartmut Hackman.
Thanks to Helmut Auer for testing and helping to optimize the patch.
tda826x:
- set baseband cut-off to 19 MHz
tda10086:
- change the parameters of the carrier recovery loop
- toggle register 0x02 between 0x35 (tuning) and 0x00 (locked)
- invert STR and SNR values
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Sliced VBI transfers use PIO instead of DMA. This was done inside the
interrupt handler, but since PIO accesses are very slow this meant that
a lot of time was spent inside the interrupt handler. All PIO copies are
now moved to a workqueue. This should fix various issues with missing time
ticks and remote key hits.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If this mutex_lock_interruptible() does fail due to signal_pending() then the
state of the driver will get trashed in interesting ways, because userspace
cannot and will not retry the close().
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the SAA7111 device is powered down, and requires re-initialisation when
the V4L device is opened (as on the NetWinder), the SAA7111 driver gets
completely confused about the current settings.
The problem is centred around the way the driver keeps _two_ cached copies
of the current settings - one of the struct video_picture settings, and one
of the registers.
When the decoder is re-initailised, the cached register settings are
overwritten, as are the values in the hardware registers. However, the
cached video_picture settings are not.
Resolve this by removing the useless and buggy second level of caching for
video_picture. Instead, provide a function which updates register values
if and only if the value we are going to write to the register has changed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The recent changes on Kconfig broke compilation when VIDEO_DEV is compiled
as module. On some cases, drivers like VIDEO_BUF are compiled with 'y' option
instead of 'm':
...
Thanks to: Toralf Forster <toralf.foerster@gmx.de> for pointing this issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Original patch and description from Neil Brown <neilb@suse.de>,
merged and adapted to splice branch by me. Neils text follows:
__generic_file_splice_read() currently samples the i_size at the start
and doesn't do so again unless it needs to call ->readpage to load
a page. After ->readpage it has to re-sample i_size as a truncate
may have caused that page to be filled with zeros, and the read()
call should not see these.
However there are other activities that might cause ->readpage to be
called on a page between the time that __generic_file_splice_read()
samples i_size and when it finds that it has an uptodate page. These
include at least read-ahead and possibly another thread performing a
read
So we must sample i_size *after* it has an uptodate page. Thus the
current sampling at the start and after a read can be replaced with a
sampling before page addition into spd.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
__generic_file_splice_read's partial page check, at eof after readpage,
not only got its calculations wrong, but also reused the loff variable:
causing data corruption when splicing from a non-0 offset in the file's
last page (revealed by ext2 -b 1024 testing on a loop of a tmpfs file).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
I've seen inode related deadlocks, so move this call outside of the
actor itself, which may hold the inode lock.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There's really no reason it's below the first use of the pointer
type, and it'll fail compilation for the network addition (for good
reason). So move it up a bit.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
QPs attached to an SRQ must never have their own RQ, and QPs not
attached to SRQs must have an RQ with at least 1 entry. Enforce all
of this in set_rq_size().
Based on a patch by Eli Cohen <eli@mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
next_port should be between sysctl_local_port_range[0] and [1].
However, it is initially set to a random value with get_random_bytes().
If the value is negative when treated as a signed integer, next_port
can end up outside the expected range because of the result of the %
operator being negative.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code in __mlx4_ib_modify_qp() overwrites context->params1 after
the RNR retry parameter is ORed in, which results in the RNR retry
parameter always being set to 0. Fix this by moving where we OR in
the value to later in the function, after the initial assignment of
context->params1.
Found by the Mellanox firmware group.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a dMPT entry has the PA flag (direct physical address) set, then
the (unused) MTT base address field has to be set to 0.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
HCA firmware with incompatible changes to the FW commmand interface is
coming soon. Add a check of the interface revision during
initialization and bail out if the firmware advertises a revision that
the driver doesn't know about. This will avoid strange failures later
if the driver goes on using the wrong interface revision.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This fixes the IDE controller not showing up on Netra-T1
systems.
Just like Simba bridges, some PCI bridges can lack the
'ranges' OBP property. So we handle this similarly to
the existing Simba code:
1) In of_device register address resolving, we push the
translation to the parent.
2) In PCI device scanning, we interrogate the PCI config
space registers of the PCI bus device in order to resolve
the resources, just like the generic Linux PCI probing
code does.
With much help and testing from Fabio, who also reported
the initial problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Fabio Massimo Di Nitto <fabbione@ubuntu.com>
To be consistent with other architectures, include the generic version
of rwsem.h.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug was caught by LTP testcase fchmod06 on Blackfin platform.
In the manpage of fchmod, "EPERM: The effective UID does not match the
owner of the file, and the process is not privileged (Linux: it does not
have the CAP_FOWNER capability)."
But the ramfs nommu code missed the inode_change_ok POSIX UID/GID
verification. This patch fixed this.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.linux-xtensa.org/kernel/xtensa-feed:
Xtensa: use asm-generic/fcntl.h
[XTENSA] Remove non-rt signal handling
[XTENSA] Move common sections into bss sections
[XTENSA] clean-up header files
[XTENSA] Use generic 64-bit division
[XTENSA] Remove multi-exported symbols from xtensa_ksyms.c
[XTENSA] fix sources using deprecated assembler directive
[XTENSA] Spelling fixes in arch/xtensa
[XTENSA] fix bit operations in bitops.h
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (24 commits)
xfrm: Add security check before flushing SAD/SPD
[NET_SCHED]: Fix filter double free
[NET]: Avoid duplicate netlink notification when changing link state
[UDP]: Revert 2-pass hashing changes.
[AF_UNIX]: Fix stream recvmsg() race.
[NETFILTER]: nf_conntrack_amanda: fix textsearch_prepare() error check
[NETFILTER]: ip_tables: fix compat related crash
[NETFILTER]: nf_conntrack: fix helper module unload races
[RTNETLINK]: ifindex 0 does not exist
[NETLINK]: Mark netlink policies const
[TCP] tcp_probe: Attach printf attribute properly to printl().
[TCP]: Use LIMIT_NETDEBUG in tcp_retransmit_timer().
[NET]: Merge dst_discard_in and dst_discard_out.
[RFKILL]: Make rfkill->name const
[IPV4]: Restore old behaviour of default config values
[IPV4]: Add default config support after inetdev_init
[IPV4]: Convert IPv4 devconf to an array
[IPV4]: Only panic if inetdev_init fails for loopback
[TCP]: Honour sk_bound_dev_if in tcp_v4_send_ack
[BNX2]: Update version and reldate.
...
This is a minor fix, but what is currently there is essentially wrong.
In do_page_fault, if the faulting address from user code happens to be
in kernel address space (int *p = (int*)-1; p = 0xbed;) then the
do_page_fault handler will jump over the local_irq_enable with the
goto bad_area_nosemaphore;
But the first line there sees this is user code and goes through the
process of sending a signal to send SIGSEGV to the user task. This whole
time interrupts are disabled and the task can not be preempted by a
higher priority task.
This patch always enables interrupts in the user path of the
bad_area_nosemaphore.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix warning by moving do_default_vi into CONFIG_CPU_MIPSR2_SRS
[MIPS] Fix some minor typoes in arch/mips/Kconfig.
[MIPS] Remove prototype for deleted function qemu_handle_int
[MIPS] Fix some system calls with long long arguments
[MIPS] Make dma_map_sg handle sg elements which are longer than one page
[MIPS] Drop __ARCH_WANT_SYS_FADVISE64
[MIPS] Fix VGA corruption on RM300C
[MIPS] RM300: Fix MMIO problems by marking the PCI INT ACK region busy
[MIPS] EMMA2RH: remove dead KGDB code
[MIPS] Remove duplicate fpu enable hazard code.
[MIPS] Atlas, Malta, SEAD: Remove scroll from interrupt handler.
In file included from /usr/src/linux-2.6-2/net/ipv4/ip_input.c:118:
include2/asm/system.h:245: error: parse error before "__cmpxchg_32"
include2/asm/system.h:245: error: parse error before '*' token
include2/asm/system.h:245: warning: type defaults to `int' in declaration of `__cmpxchg_32'
include2/asm/system.h:245: warning: function declaration isn't a prototype
include2/asm/system.h:245: warning: data definition has no type or storage class
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
