Pass HPB-DMA slave IDs in the SDHI0 platform data to enable DMA in the SDHI
driver.
Signed-off-by: Max Filippov <max.filippov@cogentembedded.com>
[Sergei: removed #include <mach/dma.h>]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Bock-W USB1 (CN29) can be USB Host/Func by SW98/SW99 settings.
USB Func will be enabled if CONFIG_USB_RENESAS_USBHS_UDC[_MODULE]
was selected on this patch
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables R-Car sound,
AK4643 (CN19) and AK4554 (CN20/CN21) codec chip
on Bock-W.
But, it supports PIO transfer only at this point.
User can check sound settings (Dip-switch/PFC etc)
via this patch, but will get under/over flow error
when playback/capture.
Because PIO transfer via SSI will be interrupted
"sampling rate" times per 1 second.
DMA transfer will be supported when HPB-DMAC was
enabled on r8a7778.
You will notice strange ALSA sound card HW
numbering on Bock-W board.
This came from AK4554 strange format on playback/capture.
The format on playback/capture is same on "normal" codec chip,
but AK4554 was different.
Because of that, AK4554 playback/capture are
registered as a different sound card.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms+renesas@verge.net.au: squashed cleanup of SND_SOC_xxx in
Kconfig by Kuninori Morimoto]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables global use of FPGA,
since it will be used from many devices.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Lots of cleanup and refactoring and some SMP additions for Renesas
platforms. Due to some inter-dependencies with other arm-soc
branches, this Renesas stuff was separated out for sending after the
other branches were merged.
Highlights:
- remove unused board support and cleanup of unused headers
- refactoring of init and device registration
- simplify IRQ initialization
Conflicts: Too many. Most of these are because Simon chose to send
some board updates through the V4L tree that ends up colliding with
the main platform changes. We'll work with him on sorting out his
workflow:
- arch/arm/boot/dts/r8a7740.dtsi:
- Add/add conflict in a devicetree file (keep both)
- arch/arm/mach-shmobile/Makefile:
- Splitting out of clock files collides with intc move to DT.
Keep HEAD version but remove intc-* files for R8A7740 and R8A7779.
- arch/arm/mach-shmobile/board-bockw.c:
- Keep HEAD but remove i2c, hspi and mmc device init calls
- arch/arm/mach-shmobile/board-marzen.c
- Remove mach/hardware.h include and r8a7779_add_usb_phy_device() call,
everything else stays.
- arch/arm/mach-shmobile/include/mach/r8a7778.h:
- From HEAD, Keep camera-rcar.h include and r8a7778_add_vin_device()
- From branch, keep everything
- arch/arm/mach-shmobile/include/mach/r8a7779.h:
- From HEAD, Keep only camera-rcar.h include and r8a7779_add_vin_device()
- arch/arm/mach-shmobile/setup-r8a7778.c
- Keep HEAD, but drop the MMC section (struct resource + add_mmc_device())
- take the new function name from our side (r8a7778_add_dt_devices())
- arch/arm/mach-shmobile/setup-r8a7779.c
- Keep HEAD, but drop r8a7779_add_usb_phy_device()
I've also pushed a test-merge2 branch where you can see how I resolved
them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Fagt
-----END PGP SIGNATURE-----
Merge tag 'renesas-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Renesas SoC cleanup, refactoring and more SMP support from Kevin Hilman:
"Lots of cleanup and refactoring and some SMP additions for Renesas
platforms. Due to some inter-dependencies with other arm-soc
branches, this Renesas stuff was separated out for sending after the
other branches were merged.
Highlights:
- remove unused board support and cleanup of unused headers
- refactoring of init and device registration
- simplify IRQ initialization"
* tag 'renesas-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (68 commits)
ARM: shmobile: Per-CPU SMP boot / sleep code for SCU SoCs
ARM: shmobile: Introduce per-CPU SMP boot / sleep code
ARM: shmobile: Use shared SCU CPU Hotplug code on r8a7779
ARM: shmobile: Use shared SCU CPU Hotplug code on sh73a0
ARM: shmobile: Add shared SCU CPU Hotplug code
ARM: shmobile: Use shared SCU SMP boot code on emev2
ARM: shmobile: Use shared SCU SMP boot code on r8a7779
ARM: shmobile: Use shared SCU SMP boot code on sh73a0
ARM: shmobile: Introduce shared SCU SMP boot code
ARM: shmobile: sh73a0: Remove global GPIO_NR definition
ARM: shmobile: kzm9d: remove nfsroot settings from bootargs
ARM: shmobile: armadillo800eva: remove nfsroot settings from bootargs
ARM: shmobile: r8a7779: move r8a7779_init_irq_xxx() to setup
ARM: shmobile: r8a7740: move r8a7740_init_irq_of() to setup
ARM: shmobile: bockw: add missing __initdata
ARM: shmobile: r8a7790: add missing __initdata
ARM: shmobile: r8a7779: add missing __initdata
ARM: shmobile: Remove unused shmobile_init_time()
ARM: shmobile: Use clocksource_of_init() on r8a7790
ARM: shmobile: Use default ->init_time() on KZM9G DT ref
...
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
Pull media updates from Mauro Carvalho Chehab:
"This series contains:
- Exynos s5p-mfc driver got support for VP8 encoder
- Some SoC drivers gained support for asynchronous registration
(needed for DT)
- The RC subsystem gained support for RC activity LED;
- New drivers added: a video decoder(adv7842), a video encoder
(adv7511), a new GSPCA driver (stk1135) and support for Renesas
R-Car (vsp1)
- the first SDR kernel driver: mirics msi3101. Due to some troubles
with the driver, and because the API is still under discussion, it
will be merged at staging for 3.12. Need to rework on it
- usual new boards additions, fixes, cleanups and driver
improvements"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (242 commits)
[media] cx88: Fix regression: CX88_AUDIO_WM8775 can't be 0
[media] exynos4-is: Fix entity unregistration on error path
[media] exynos-gsc: Register v4l2 device
[media] exynos4-is: Fix fimc-lite bayer formats
[media] em28xx: fix assignment of the eeprom data
[media] hdpvr: fix iteration over uninitialized lists in hdpvr_probe()
[media] usbtv: Throw corrupted frames away
[media] usbtv: Fix deinterlacing
[media] v4l2: added missing mutex.h include to v4l2-ctrls.h
[media] DocBook: upgrade media_api DocBook version to 4.2
[media] ml86v7667: fix compile warning: 'ret' set but not used
[media] s5p-g2d: Fix registration failure
[media] media: coda: Fix DT driver data pointer for i.MX27
[media] s5p-mfc: Fix input/output format reporting
[media] v4l: vsp1: Fix mutex double lock at streamon time
[media] v4l: vsp1: Add support for RT clock
[media] v4l: vsp1: Initialize media device bus_info field
[media] davinci: vpif_capture: fix error return code in vpif_probe()
[media] davinci: vpif_display: fix error return code in vpif_probe()
[media] MAINTAINERS: add entries for adv7511 and adv7842
...
* Remove global GPIO_NR definition from sh73a0 SoC
* Remove unnecessary nfsroot settings from bootargs of
kzm9d and armadillo800eva
* Rename irq initialisation functions of r8a7779 SoC
to make them consistent with other SoCs
* Simplify irq initialisation of r8a7740 SoC
* Add missing __initdata annotations to bockw board, and
r8a7790 and r8a7779 SoCs
* Refactor time initialisation and remove shmobile_init_time.
- This affects the following boards: kzm9g, marzen, ape6evm,
armadillo800eva and bockw
- This affects the following SoCs: r8a7790, r8a7779, r7a7740, r7a73a4
* Cleanup device registration code of r8a7778 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Sbjt
-----END PGP SIGNATURE-----
Merge tag 'renesas-cleanup3-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/renesas
From Simon Horman:
Third round of Renesas ARM based SoC cleanups for v3.12
* Remove global GPIO_NR definition from sh73a0 SoC
* Remove unnecessary nfsroot settings from bootargs of
kzm9d and armadillo800eva
* Rename irq initialisation functions of r8a7779 SoC
to make them consistent with other SoCs
* Simplify irq initialisation of r8a7740 SoC
* Add missing __initdata annotations to bockw board, and
r8a7790 and r8a7779 SoCs
* Refactor time initialisation and remove shmobile_init_time.
- This affects the following boards: kzm9g, marzen, ape6evm,
armadillo800eva and bockw
- This affects the following SoCs: r8a7790, r8a7779, r7a7740, r7a73a4
* Cleanup device registration code of r8a7778 SoC
* tag 'renesas-cleanup3-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (45 commits)
ARM: shmobile: sh73a0: Remove global GPIO_NR definition
ARM: shmobile: kzm9d: remove nfsroot settings from bootargs
ARM: shmobile: armadillo800eva: remove nfsroot settings from bootargs
ARM: shmobile: r8a7779: move r8a7779_init_irq_xxx() to setup
ARM: shmobile: r8a7740: move r8a7740_init_irq_of() to setup
ARM: shmobile: bockw: add missing __initdata
ARM: shmobile: r8a7790: add missing __initdata
ARM: shmobile: r8a7779: add missing __initdata
ARM: shmobile: Remove unused shmobile_init_time()
ARM: shmobile: Use clocksource_of_init() on r8a7790
ARM: shmobile: Use default ->init_time() on KZM9G DT ref
ARM: shmobile: Use default ->init_time() on Marzen DT ref
ARM: shmobile: Use default ->init_time() on APE6EVM DT ref
ARM: shmobile: Use default ->init_time() on APE6EVM
ARM: shmobile: Use default ->init_time() on Armadillo DT ref
ARM: shmobile: Use default ->init_time() on Bockw DT ref
ARM: shmobile: Use default ->init_time() on Bockw
ARM: shmobile: Use default ->init_time() on r8a7779
ARM: shmobile: Use default ->init_time() on r8a7778
ARM: shmobile: Use default ->init_time() on r8a7740
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add ML86V7667 platform devices on BOCK-W board, configure VIN0/1 pins, and
register VIN0/1 devices with the ML86V7667 specific platform data.
[Sergei: some macro/comment cleanup; updated the copyrights, removed duplicate
'sh_eth' driver being enabled before registering VIN1 due to a pin conflict,
removed superfluous semicolon after iclink[01]_ml86v7667' initializer.]
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that the 'register_type' field of the 'sh_eth' driver's platform data is not
used by the driver anymore, it's time to remove it and its initializers from
the SH platform code. Also move *enum* declaring values for this field from
<linux/sh_eth.h> to the local driver's header file as they're only needed
by the driver itself now...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds missing __initdata to driver data/resource
which are used from platform_device_register_xxx()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Leave ->init_time() set to NULL to use the default ARM behaviour.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
sh-hspi driver which doesn't need platform data at the time of
registration can be registerd on SoC.
And, registering these drivers in the SoC code can avoid
unwanted device numbering issue.
(ex. the hspi2 device number will be spi.0 if hspi2 only registered)
This patch registers it on SoC code as cleanup C code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
i2c-rcar driver which doesn't need platform data at the time of
registration can be registerd on SoC.
And, registering these drivers in the SoC code can avoid
unwanted device numbering issue.
(ex. the i2c3 device number will be i2c.0 if i2c3 only registered)
This patch registers it on SoC code as cleanup C code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
sdhi driver which needs platform data at the time of
registration is used from BockW only.
Now, ARM/shmobile aims to support DT,
and the C code base board support will be removed
if DT support is completed.
Current driver registration method which needs platform data
and which is not shared complicates codes.
This means legacy C code cleanup after DT supporting
will be more complicated
This patch registers it on board code as cleanup C code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
usb phy driver which needs platform data at the time of
registration is used from BockW only.
Now, ARM/shmobile aims to support DT,
and the C code base board support will be removed
if DT support is completed.
Current driver registration method which needs platform data
and which is not shared complicates codes.
This means legacy C code cleanup after DT supporting
will be more complicated
This patch registers it on board code as cleanup C code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
sh_mmcif driver which needs platform data at the time of
registration is used from BockW only.
Now, ARM/shmobile aims to support DT,
and the C code base board support will be removed
if DT support is completed.
Current driver registration method which needs platform data
and which is not shared complicates codes.
This means legacy C code cleanup after DT supporting
will be more complicated
This patch registers it on board code as cleanup C code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The following message is printed on the BOCK-W kernel bootup:
sh-pfc pfc-r8a7778: invalid group "sdhi0" for function "sdhi0"
In addition, SD card cannot be detected. The reason is apparently that commit
ca7bb30948 (ARM: shmobile: bockw: add SDHI0 support) matched
the previous version of commit 564617d2f9 (sh-pfc: r8a7778:
add SDHI support).
Add the missing pin groups according to the BOCK-W board schematics.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
These are 18 branches on 9 platforms with board specific changes, mostly
for defconfig files, but nothing really exciting in here.
Since the shmobile platform still uses board files for some of the newer
machines, we get a few changes there as the result of drivers getting
enabled for those boards. This causes some conflicts with contents getting
added from multiple branches in sh-mobile specific files. Renesas is
putting a lot of work into migrating to device-tree based setup, which
will make all those files obsolete in the future and avoid both the
conflicts and the need to have these files in the first place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7bgc
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board specific changes from Arnd Bergmann:
"These are 18 branches on 9 platforms with board specific changes,
mostly for defconfig files, but nothing really exciting in here.
Since the shmobile platform still uses board files for some of the
newer machines, we get a few changes there as the result of drivers
getting enabled for those boards. This causes some conflicts with
contents getting added from multiple branches in sh-mobile specific
files. Renesas is putting a lot of work into migrating to device-tree
based setup, which will make all those files obsolete in the future
and avoid both the conflicts and the need to have these files in the
first place."
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits)
arm: multi_v7_defconfig: Enable initrd/initramfs support
arm: multi_v7_defconfig: Enable Zynq UART driver
ARM: omap2plus_defconfig: enable USB_PHY and NOP_USB_XCEIV
ARM: OMAP1: nokia770: enable Tahvo
ARM: OMAP3EVM: Marking omap3_evm_display_init() with CONFIG_BROKEN
arm: omap: board-overo: reset GPIO for SMSC911x
ARM: shmobile: BOCK-W: change Ether device name
ARM: ux500: board-mop500: remove unused pin modes
ARM: shmobile: bockw: add MMCIF support
ARM: shmobile: bockw: add SPI FLASH support
ARM: shmobile: bockw: add I2C device support
ARM: shmobile: BOCK-W: add Ether support
ARM: tegra: defconfig updates
ARM: shmobile: bockw defconfig: add MMCIF support
ARM: shmobile: bockw defconfig: add M25P80 support
ARM: shmobile: bockw defconfig: add RTC RX8581 support
ARM: shmobile: marzen: keep local function as static
ARM: shmobile: bockw: add SDHI0 support
ARM: shmobile: marzen: Use INTC External IRQ pin driver for SMSC
ARM: shmobile: lager: support GPIO switches
...
When changing the name of Ether platform device in the commit c02f846938 (ARM:
shmobile: r8a7778: fix Ether device name), I completely forgot that there's also
platform device name used in bockw_pinctrl_map[], so the commit "ARM: shmobile:
BOCK-W: add Ether support" went in with the old "sh-eth" device name. Now change
it to "r8a777x-ether" in accordance with the commits that are now in the 'net-
next.git' repository, otherwise BOCK-W Ether support won't work in 3.11.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables Spansion S25FL008K chip on HSPI0
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables rx8581 on I2C0
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Register Ether device from bockw_init(), passing the platform data to it, adding
only the RMII pin group to bockw_pinctrl_map[]. Although the LINK signal exists
on the board, it's connected to the link/activity LED output of the PHY, thus
the link disappears and reappears after each packet. We'd be better off ignoring
such signal and getting the link state from the PHY indirectly.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[horms+renesas@verge.net.au: manually applied]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Register the USB PHY device from bockw_init(), passing the platform data to it.
Set machine's init_late() method to r8a7778_init_late() in order for [EO]HCI to
get registered too...
Don't forget to add USB PENC0/1 pins to bockw_pinctrl_map[].
The patch has been tested on the BOCK-W board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch is directly accessing to PUPR4 register which can
control SDHI0 CD/WP pin pull-up setting.
It should be replaced in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SMSC driver will try to get regulator if .config had CONFIG_REGULATOR,
and, shmobile_defconfig has it.
SMSC driver on Bock-W board will be failed if it doens't have
dummy regulator settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Debug serial (= SCIF0) is connected to CN9 upper side,
and it is shared by RCAN.
This patch adds SCIF/RCAN dipswitch explanation on
comment area for developers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Bock-W board will needs more board specific ioremap() method.
This patch tidyup current FPGA specific settings
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds SMSC ethernet support on Bock-W
Bock-W SMSC needs FPGA settings which enables interrupt.
This patch does it on bockw_init() function.
As notes for future, this FPGA settings should be updated,
since this FPGA is using cascaded interrupt.
Current code is assuming that this FPGA interrupt user is only SMSC.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add basic Bock-W board support
More devices will be added on top of this patch after
PICNTRL and clock framework are in better shape.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
