According to SPEC, the minimum_linkrate and maximum_linkrate should be
settable by the user. This patch introduces a callback that allows the
sas class to pass these settings on to the driver.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
At the moment we have two separate linkspeed enumerations covering
roughly the same values. This patch consolidates on a single one enum
sas_linkspeed in scsi_transport_sas.h and uses it everywhere in the
aic94xx driver. Eventually I'll get around to removing the duplicated
fields in asd_sas_phy and sas_phy ...
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds the following functionality to the FC transport:
- dev_loss_tmo LLDD callback :
Called to essentially confirm the deletion of an rport. Thus, it is
called whenever the dev_loss_tmo fires, or when the rport is deleted
due to other circumstances (module unload, etc). It is expected that
the callback will initiate the termination of any outstanding i/o on
the rport.
- fast_io_fail_tmo and LLD callback:
There are some cases where it may take a long while to truly determine
device loss, but the system is in a multipathing configuration that if
the i/o was failed quickly (faster than dev_loss_tmo), it could be
redirected to a different path and completed sooner.
Many thanks to Mike Reed who cleaned up the initial RFC in support
of this post.
The original RFC is at:
http://marc.theaimsgroup.com/?l=linux-scsi&m=115505981027246&w=2
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
During discussions with Mike Christie, I became convinced that we needed
a larger vendor id. This patch extends the id from 32 to 64 bits.
This applies on top of the prior patches that add SCSI transport events
via netlink.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch formally adds support for the posting of FC events via netlink.
It is a followup to the original RFC at:
http://marc.theaimsgroup.com/?l=linux-scsi&m=114530667923464&w=2
and the initial posting at:
http://marc.theaimsgroup.com/?l=linux-scsi&m=115507374832500&w=2
The patch has been updated to optimize the send path, per the discussions
in the initial posting.
Per discussions at the Storage Summit and at OLS, we are to use netlink for
async events from transports. Also per discussions, to avoid a netlink
protocol per transport, I've create a single NETLINK_SCSITRANSPORT protocol,
which can then be used by all transports.
This patch:
- Creates new files scsi_netlink.c and scsi_netlink.h, which contains the
single and shared definitions for the SCSI Transport. It is tied into the
base SCSI subsystem intialization.
Contains a single interface routine, scsi_send_transport_event(), for a
transport to send an event (via multicast to a protocol specific group).
- Creates a new scsi_netlink_fc.h file, which contains the FC netlink event
messages
- Adds 3 new routines to the fc transport:
fc_get_event_number() - to get a FC event #
fc_host_post_event() - to send a simple FC event (32 bits of data)
fc_host_post_vendor_event() - to send a Vendor unique event, with
arbitrary amounts of data.
Note: the separation of event number allows for a LLD to send a standard
event, followed by vendor-specific data for the event.
Note: This patch assumes 2 prior fc transport patches have been installed:
http://marc.theaimsgroup.com/?l=linux-scsi&m=115555807316329&w=2http://marc.theaimsgroup.com/?l=linux-scsi&m=115581614930261&w=2
Sorry - next time I'll do something like making these individual
patches of the same posting when I know they'll be posted closely
together.
Signed-off-by: James Smart <James.Smart@emulex.com>
Tidy up configuration not to make SCSI always select NET
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It is possible that a ctask could be completing and getting
cleaned up at the same time, we are finishing up the last
data transfer. This could then result in the data transfer
code using stale or invalid values. This patch adds a refcount
to the ctask. When the count goes to zero then we know the
transmit thread and recv thread or softirq are not touching
it and we can safely release it.
The eh should not need to grab a reference because it only cleans
up a task if it has both the xmit mutex and recv lock (or recv
side suspended).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
iSCSI RFC states that the first burst length must be smaller than the
max burst length. We currently assume targets will be good, but that may
not be the case, so this patch adds a check.
This patch also moves the unsol data out offset to the lib so the LLDs
do not have to track it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds support for sharing tag maps at the host level
(i.e. either every queue [LUN] has its own tag map or there's a single
one for the entire host). This formulation is primarily intended to
help single issue queue hardware, like the aic7xxx
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is the end point of the separate aic94xx driver based on the
original driver and transport class from Luben Tuikov
<ltuikov@yahoo.com>
The log of the separate development is:
Alexis Bruemmer:
o aic94xx: fix hotplug/unplug for expanderless systems
o aic94xx: disable split completion timer/setting by default
o aic94xx: wide port off expander support
o aic94xx: remove various inline functions
o aic94xx: use bitops
o aic94xx: remove queue comment
o aic94xx: remove sas_common.c
o aic94xx: sas remove depot's
o aic94xx: use available list_for_each_entry_safe_reverse()
o aic94xx: sas header file merge
James Bottomley:
o aic94xx: fix TF_TMF_NO_CTX processing
o aic94xx: convert to request_firmware interface
o aic94xx: fix hotplug/unplug
o aic94xx: add link error counts to the expander phys
o aic94xx: add transport class phy reset capability
o aic94xx: remove local_attached flag
o Remove README
o Fixup Makefile variable for libsas rename
o Rename sas->libsas
o aic94xx: correct return code for sas_discover_event
o aic94xx: use parent backlink port
o aic94xx: remove channel abstraction
o aic94xx: fix routing algorithms
o aic94xx: add backlink port
o aic94xx: fix cascaded expander properties
o aic94xx: fix sleep under lock
o aic94xx: fix panic on module removal in complex topology
o aic94xx: make use of the new sas_port
o rename sas_port to asd_sas_port
o Fix for eh_strategy_handler move
o aic94xx: move entirely over to correct transport class formulation
o remove last vestages of sas_rphy_alloc()
o update for eh_timed_out move
o Preliminary expander support for aic94xx
o sas: remove event thread
o minor warning cleanups
o remove last vestiges of id mapping arrays
o Further updates
o Convert aic94xx over entirely to the transport class end device and
o update aic94xx/sas to use the new sas transport class end device
o [PATCH] aic94xx: attaching to the sas transport class
o Add missing completion removal from prior patch
o [PATCH] aic94xx: attaching to the sas transport class
o Build fixes from akpm
Jeff Garzik:
o [scsi aic94xx] Remove ->owner from PCI info table
Luben Tuikov:
o initial aic94xx driver
Mike Anderson:
o aic94xx: fix panic on module insertion
o aic94xx: stub out SATA_DEV case
o aic94xx: compile warning cleanups
o aic94xx: sas_alloc_task
o aic94xx: ref count update
o aic94xx nexus loss time value
o [PATCH] aic94xx: driver assertion in non-x86 BIOS env
Randy Dunlap:
o libsas: externs not needed
Robert Tarte:
o aic94xx: sequence patch - fixes SATA support
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This flag denotes local attachment of the phy. There are two problems
with it:
1) It's actually redundant ... you can get the same information simply
by seeing whether a host is the phys parent
2) we condition a lot of phy parameters on it on the false assumption
that we can only control local phys. I'm wiring up phy resets in the
aic94xx now, and it will be able to reset non-local phys as well.
I fixed 2) by moving the local check into the reset and stats function
of the mptsas, since that seems to be the only HBA that can't
(currently) control non-local phys.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch updates the fc transport for the following:
- Addition of a new attribute "system_hostname" which can be
used to set the fully qualified hostname that the fc_host
is attached to. The fc_host can then register this string
as the FDMI-based host name attribute.
Note: for NPIV, a fc_host could be associated with a system which
is not the local system.
- Add the inline function u64_to_wwn(), which is the inverse of the
existing wwn_to_u64() function.
- Slight reorg, just to keep dynamic attributes with each other, etc
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Replace scsi_device_types array API with scsi_device_type function API.
Gets rid of a lot of common code, as well as being easier to use.
- Add the new device types in SPC4 r05a, and rename some of the older ones.
- Reformat the printing of inquiry data; now fits on one line and
includes PQ.
I think I've addressed all the feedback from the previous versions. My
current test box prints:
scsi 2:0:1:0: Direct access HP 18.2G ATLAS10K3_18_SCA HP05 PQ: 0 ANSI: 2
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
These aren't used anymore since the field in scsi_cmnd where it was
stored has been removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We currently try to allocate a max_recv_data_segment_length
which can be very large (default is 64K), and common uses
are up to 1MB. It is very very difficult to allocte this
much contiguous memory and it turns out we never even use it.
We really only need a couple of pages, so this patch has us
allocates just what we know what we need today.
Later if vendors start adding vendor specific data and
we need to handle large buffers we can do this, but for
the last 4 years we have not seen anyone do this or request
it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When we enter recovery and flush the running commands
we cannot freee the connection before flushing the commands.
Some commands may have a reference to the connection
that needs to be released before. iscsi_stop was forcing
the term and suspend too early and was causing a oops
in iser, so this patch removes those callbacks all together
and allows the LLD to handle that detail.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Abort handler fixes.
If a connection is dropped and reconnected while an abort is
running then we should assume the recovery code will clean up
the abort. Not doing so causes a oops.
And if a command completes then we get the status for the abort, we do not
need to call into the LLD to cleanup the resources. Doing this causes
and oops in iser because it ends up freeing some resources twice.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The iscsi tcp code can pluck multiple rt2s from the tasks's r2tqueue
in the xmit code. This can result in the task being queued on the xmit queue
but gettting completed at the same time.
This patch fixes the above bug by making the fifo a list so
we always remove the entry on the list del.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds the ability to add a backlink to a particular port. The
idea is to represent properly ports on expanders that are used
specifically for linking to the parent device in the topology.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently struct scsi_cmnd has various fields that are used to backup
original data after the corresponding fields have been overridden for
EH commands. This means drivers can easily get at it and misuse it.
Due to the old_ naming this doesn't happen for most of them, but two
that have different names have been used wrong a lot (see previous
patch). Another downside is that they unessecarily bloat the scsi_cmnd
size.
This patch moves them onstack in scsi_send_eh_cmnd to fix those two
issues aswell as allowing future EH fixes like moving the EH command
submissions to use SG lists like everything else.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some SAS HBAs don't want to go to the trouble of tracking port numbers,
so they'd simply like to say "add this port and give it a number".
This is especially beneficial from the hotplug point of view, since
tracking ports and the available number space can be a real pain.
The current implementation uses an incrementing number per expander to
add the port on. However, since there can never be more ports than
there are phys, a later implementation will try to be more intelligent
about this.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds or modifies the transport class functions
used to notify userspace of session state events.
We modify the session addition up event and add a destruction event
to notify userspace of session creation, relogin and destruction.
And we modify the conn error event to be sent by broadcast
since multiple listeners may want to listen for it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
So the drivers do not use the channel numbers, but some do
use the target numbers. We were just adding some goofy
variable that just increases for the target nr. This is useless
for software iscsi because it is always zero. And for qla4xxx
the target nr is actually the index of the target/session
in its FW or FLASH tables. We needed to expose this to userspace
so apps could access those numbers so this patch just adds the
target nr to the iscsi session creation functions. This way
when qla4xxx's Hw thinks a session is at target nr 4
in its hw, it is exposed as that number in sysfs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
qla4xxx is initialized in two steps like other HW drivers.
It allocates the host, sets up the HW, then adds the host.
For iscsi part of HW setup is setting up persistent iscsi
sessions. At that time, the interupts are off and the driver
is not completely set up so we just want to allocate them.
We do not want to add them to sysfs and expose them to userspace
because userspace could try to do lots of fun things with them
like scanning and at that time the driver is not ready.
So this patch breakes up the session creation like other
functions that use the driver model in two the alloc
and add parts. When the driver is ready, it can then add
the sessions and userspace can begin using them.
This also fixes a bug in the addition error patch where
we forgot to do a get on the session.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I do not remember what I was thinking when we added the channel
as a argument to the session create function. It was probably
due to too much cut and paste work from the FC transport class.
The channel is meaningless for iscsi drivers so this patch drops
its usage everywhere in the iscsi related code.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Reduce duplication in the software iscsi_transport modules by
adding a libiscsi function to handle the common grunt work.
This also has the drivers return specifc -EXXX values for different
errors so userspace can finally handle them in a sane way.
Also just pass the sysfs buffers to the drivers so HW iscsi can
get/set its string values, like targetname, and initiatorname.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from david.somayajulu@qlogic.com:
Add target discovery event. We may have a setup where the iscsi traffic
is on a different netowrk than the other network traffic. In this case
we will want to do discovery though the iscsi card. This patch adds
a event to the transport class that can be used by hw iscsi cards that
support this.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
this patch introduces a port object, separates out ports and phys,
with ports becoming the primary objects of the tree.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The scsi midlayer portion of the patch
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch simplifies "good_bytes" computation in sd_rw_intr().
sd: "good_bytes" computation is always done in terms of the resolution
of the device's medium, since after that it is the number of good bytes
we pass around and other layers/contexts (as opposed ot sd) can translate
that to their own resolution (block layer:512). It also makes
scsi_io_completion() processing more straightforward, eliminating the
3rd argument to the function.
It also fixes a couple of bugs like not checking return value,
using "break" instead of "return;", etc.
I've been running with this patch for some time now on a
test (do-it-all) system.
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* git://git.infradead.org/hdrcleanup-2.6: (63 commits)
[S390] __FD_foo definitions.
Switch to __s32 types in joystick.h instead of C99 types for consistency.
Add <sys/types.h> to headers included for userspace in <linux/input.h>
Move inclusion of <linux/compat.h> out of user scope in asm-x86_64/mtrr.h
Remove struct fddi_statistics from user view in <linux/if_fddi.h>
Move user-visible parts of drivers/s390/crypto/z90crypt.h to include/asm-s390
Revert include/media changes: Mauro says those ioctls are only used in-kernel(!)
Include <linux/types.h> and use __uXX types in <linux/cramfs_fs.h>
Use __uXX types in <linux/i2o_dev.h>, include <linux/ioctl.h> too
Remove private struct dx_hash_info from public view in <linux/ext3_fs.h>
Include <linux/types.h> and use __uXX types in <linux/affs_hardblocks.h>
Use __uXX types in <linux/divert.h> for struct divert_blk et al.
Use __u32 for elf_addr_t in <asm-powerpc/elf.h>, not u32. It's user-visible.
Remove PPP_FCS from user view in <linux/ppp_defs.h>, remove __P mess entirely
Use __uXX types in user-visible structures in <linux/nbd.h>
Don't use 'u32' in user-visible struct ip_conntrack_old_tuple.
Use __uXX types for S390 DASD volume label definitions which are user-visible
S390 BIODASDREADCMB ioctl should use __u64 not u64 type.
Remove unneeded inclusion of <linux/time.h> from <linux/ufs_fs.h>
Fix private integer types used in V4L2 ioctls.
...
Manually resolve conflict in include/linux/mtd/physmap.h
This adds the Kbuild files listing the files which are to be installed by
the 'headers_install' make target, in generic directories.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add enum values for I/O Class values from rev. 10 and rev. 16a SRP
drafts. The values are used to detect targets that implement obsolete
revisions of SRP, so that the initiator can use the old format for
port identifier when connecting to them.
Signed-off-by: Ramachandra K <rkuchimanchi@silverstorm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With Achim patch the last user (gdth) is switched away from scsi_request
so we an kill it now. Also disables some code in i2o_scsi that was
broken since the sg driver stopped using scsi_requests.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We can race and misset the suspend bit if iscsi_write_space is
called then iscsi_send returns with a failure indicating
there is no space.
To handle this this patch returns a error upwards allowing xmitworker
to decide if we need to try and transmit again. For the no
write space case xmitworker will not retry, and instead
let iscsi_write_space queue it back up if needed (this relies
on the work queue code to properly requeue us if needed).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If recovery failed or we are in recovery only overwrite the state
if we are going to terminate the session or if we logged back in.
STOP_CONN_SUSPEND and conn_cnt are not used. We only support
a single connection session ATM, so cleanup that code while
we are working around it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Do not flush queues then block session. This will cause commands
to needlessly swing around on us and remove goofy
recovery_failed field and replace with state value.
And do not start recovery from within the host reset function.
This causeis too many problems becuase open-iscsi was desinged to
call out to userspace then have userpscae decide if we should
go into recovery or kill the session.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
libata implemented a feature to schedule EH without an associated EH
by manipulating shost->host_eh_scheduled in ata_scsi_schedule_eh()
directly. Move this function to scsi_error.c and rename it to
scsi_schedule_eh(). It is now an exported API for SCSI transports and
exported via new header file drivers/scsi/scsi_transport_api.h
This patch also de-export scsi_eh_wakeup() which was exported
specifically for ata_scsi_schedule_eh().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata needs to invoke EH without scmd. This patch adds
shost->host_eh_scheduled to implement such behavior.
Currently the only user of this feature is libata and no general
interface is defined. This patch simply adds handling for
host_eh_scheduled where needed and exports scsi_eh_wakeup() to
modules. The rest is upto libata. This is the result of the
following discussion.
http://thread.gmane.org/gmane.linux.scsi/23853/focus=9760
In short, SCSI host is not supposed to know about exceptions unrelated
to specific device or command. Such exceptions should be handled by
transport layer proper. However, the distinction is not essential to
ATA and libata is planning to depart from SCSI, so, for the time
being, libata will be using SCSI EH to handle such exceptions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Introduce scsi_req_abort_cmd(struct scsi_cmnd *).
This function requests that SCSI Core start recovery for the
command by deleting the timer and adding the command to the eh
queue. It can be called by either LLDDs or SCSI Core. LLDDs who
implement their own error recovery MAY ignore the timeout event if
they generated scsi_req_abort_cmd.
First post:
http://marc.theaimsgroup.com/?l=linux-scsi&m=113833937421677&w=2
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
debugged by Ming and Rohan:
The problem Ming and Rohan debugged was that during a normal session
login, open-iscsi is not incrementing the exp_statsn counter. It was
stuck at zero. From the RFC, it looks like if the login response PDU has
a successful status then we should be incrementing that value. Also from
the RFC, it looks like if when we drop a connection then reconnect, we
should be using the exp_statsn from the old connection in the next
relogin attempt.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
align printk output
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
add transport end point callbacks so iscsi drivers that cannot connect
from userspace, like iscsi tcp, using sockets do not have to
implement their own socket infrastructure.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Several structs in <scsi/srp.h> get padded to a multiple of 8 bytes on
64-bit architectures and end up with a size that does not match the
definition in the SRP spec:
SRP spec 64-bit
sizeof (struct indirect_buf) 20 24
sizeof (struct srp_login_rsp) 52 56
sizeof (struct srp_rsp) 36 40
Fix this by adding __attribute__((packed)) to the offending structs.
Problem pointed out by Arne Redlich <arne.redlich@xiranet.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The current dc395x driver uses PIO to transfer up to 4 bytes which do not
get transferred by DMA (under unclear circumstances). For this the driver
uses page_address() which is broken on highmem. Apart from this the
actual calculation of the virtual address is wrong (even without highmem).
So, e.g., for reading it reads bytes from the driver to a wrong address
and returns wrong data, I guess, for writing it would just output random
data to the device.
The proper fix, as suggested by many, is to dynamically map data using
kmap_atomic(page, KM_BIO_SRC_IRQ) / kunmap_atomic(virt). The reason why it
has not been done until now, although I've done some preliminary patches
more than a year ago was that nobody interested in fixing this problem was
able to reliably reproduce it. Now it changed - with the help from
Sebastian Frei (CC'ed) I was able to trigger the PIO path. Thus, I was
also able to test and debug it.
There are 4 cases when PIO is used in dc395x - data-in / -out with and
without scatter-gather. I was able to reproduce and test only data-in with
and without SG. So, the data-out path is still untested, but it is also
somewhat simpler than the data-in. Fredrik Roubert (also CC'ed) also had
PIO triggering on his system, and in his case it was data-out without SG.
It would be great if he could test the attached patch on his system, but
even if he cannot, I would still request to apply the patch and just wait
if anybody cries...
Implementation: I put 2 new functions in scsi_lib.c and their declarations
in scsi_cmnd.h. I exported them without _GPL, although, I don't feel
strongly about that - not many drivers are likely to use them. But there
is at least one more - I want to use them in tmscsim.c. Whether these are
the right files for the functions and their declarations - not sure
either. Actually, they are not scsi-specific, so, might go somewhere
around other scattergather magic? They are not platform specific either,
and most SG functions are defined under arch/*/... As these issues were
discussed previously there were some more routines suggested to manipulate
scattergather buffers, I think, some of them were needed around
crypto code... So, might be a common place reasonable, like
lib/scattergather.c? I am open here.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
include/scsi/scsi_devinfo.h
Same number for two BLIST flags: BLIST_MAX_512 and BLIST_ATTACH_PQ3
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There is a lot of code duplcited between iscsi_tcp
and the upcoming iscsi_iser driver. This patch puts
the duplicated code in a lib. There is more code
to move around but this takes care of the
basics. For iscsi_offload if they use the lib we will
probably move some things around. For example in the
queuecommand we will not assume that the LLD wants
to do queue_work, but it is better to handle that
later when we know for sure what iscsi_offload looks
like (we could probably do this for iscsi_iser though to).
Ideally I would like to get the iscsi_transports modules
to a place where all they really have to do is put data
on the wire, but how to do that will hopefully be more clear
when we see other modules like iscsi_offload. Or maybe
iscsi_offload will not use the lib and it will just be
iscsi_iser and iscsi_tcp and maybe the iscsi_tcp_tgt if that
is allowed in mainline.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The current iscsi_tcp eh is not nicely setup for dm-multipath
and performs some extra task management functions when they
are not needed.
The attached patch:
- Fixes the TMF issues. If a session is rebuilt
then we do not send aborts.
- Fixes the problem where if the host reset fired, we would
return SUCCESS even though we had not really done anything
yet. This ends up causing problem with scsi_error.c's TUR.
- If someone has turned on the userspace nop daemon code to try
and detect network problems before the scsi command timeout
we can now drop and clean up the session before the scsi command
timesout and fires the eh speeding up the time it takes for a
command to go from one patch to another. For network problems
we fail the command with DID_BUS_BUSY so if failfast is set
scsi_decide_disposition fails the command up to dm for it to
try on another path.
- And we had to add some basic iscsi session block code. Previously
if we were trying to repair a session we would retrun a MLQUEUE code
in the queuecommand. This worked but it was not the most efficient
or pretty thing to do since it would take a while to relogin
to the target. For iscsi_tcp/open-iscsi a lot of the iscsi error handler
is in userspace the block code is pretty bare. We will be
adding to that for qla4xxx.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For iscsi boot when going from initramfs to the real root we
need to stop the userpsace iscsi daemon. To later restart it
iscsid needs to be able to rebuild itself and part of that
process is matching a session running the kernel with the
iscsid representation. To do this the attached patch
adds several required iscsi values. If the LLD does not provide
them becuase, login is done in userspace, then the transport
class and userspace set ths up for the LLD.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
from hare@suse.de and michaelc@cs.wisc.edu
hw iscsi like qla4xxx does not allocate a host per session and
for userspace it is difficult to restart iscsid using the
"iscsi handles" for the session and connection, so this
patch just has the class or userspace allocate the id for
the session and connection.
Note: this breaks userspace and requires users to upgrade to the newest
open-iscsi tools. Sorry about his but open-iscsi is still too new to
say we have a stable user-kernel api and we were not good nough
designers to know that other hw iscsi drivers and iscsid itself would
need such changes. Actually we sorta did but at the time we did not
have the HW available to us so we could only guess.
Luckily, the only tools hooking into the class are the open-iscsi ones
or other tools like iscsitart hook into the open-iscsi engine from
userspace or prgroams like anaconda call our tools so they are not affected.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some devices report a peripheral qualifier of 3 for LUN 0; with the original
code, we would still try a REPORT_LUNS scan (if SCSI level is >= 3 or if we
have the BLIST_REPORTLUNS2 passed in), but NOT any sequential scan.
Also, the device at LUN 0 (which is not connected according to the PQ) is not
registered with the OS.
Unfortunately, SANs exist that are SCSI-2 and do NOT support REPORT_LUNS, but
report a unknown device with PQ 3 on LUN 0. We still need to scan them, and
most probably we even need BLIST_SPARSELUN (and BLIST_LARGELUN). See the bug
reference for an infamous example.
This is patch 3/3:
3. Implement the blacklist flag BLIST_ATTACH_PQ3 that makes the scsi
scanning code register PQ3 devices and continues scanning; only sg
will attach thanks to scsi_bus_match().
Signed-off-by: Kurt Garloff <garloff@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As previously reported via Michael Reed, the FC transport took a hit
in 2.6.15 (perhaps a little earlier) when we solved a recursion error.
There are 2 deadlocks occurring:
- With scan and the delete items sharing the same workq, flushing the
workq for the delete code was getting it stalled behind a very long
running scan code path.
- There's a deadlock where scsi_remove_target() has to sit behind
scsi_scan_target() due to contention over the scan_lock().
This patch resolves the 1st deadlock and significantly reduces the
odds of the second. So far, we have only replicated the 2nd deadlock
on a highly-parallel SMP system. More on the 2nd deadlock in a following
email.
This patch reworks the transport to:
- Only use the scsi host workq for scanning
- Use 2 other workq's internally. One for deletions, the other for
scheduled deletions. Originally, we tried this with a single workq,
but the occassional flushes of the scheduled queues was hitting the
second deadlock with a slightly higher frequency. In the future, we'll
look at the LLDD's and the transport to see if we can get rid of this
extra overhead.
- When moving to the other workq's we tightened up some object states
and some lock handling.
- Properly syncs adds/deletes
- minor code cleanups
- directly reference fc_host_attrs, rather than through attribute
macros
- flush the right workq on delayed work cancel failures.
Large kudos to Michael Reed who has been working this issue for the last
month.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original From: Ingo Flaschberger <if@xip.at>
To support the RA4100 array from Compaq.
This patch now correctly handles SCSI_UNKNOWN types with regard to
BLIST_REPORTLUNS2 (allow it) and cdb[1] LUN inclusion (don't).
It also allows a BLIST_MAX_512 flag to restrict the maximum transfer
length to 512 blocks (apparently this is an RA4100 problem).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We currently have two implementations of this obsolete ioctl, one in
the block layer and one in the scsi code. Both of them have drawbacks.
This patch kills the scsi layer version after updating the block version
with the missing bits:
- argument checking
- use scatterlist I/O
- set number of retries based on the submitted command
This is the last user of non-S/G I/O except for the gdth driver, so
getting this in ASAP and through the scsi tree would be nie to kill
the non-S/G I/O path. Jens, what do you think about adding a check
for non-S/G I/O in the midlayer?
Thanks to Or Gerlitz for testing this patch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Overriding the whole EH code is a per-transport, not per-host thing.
Move ->eh_strategy_handler to the transport class, same as
->eh_timed_out.
Downside is that scsi_host_alloc can't check for the total lack of EH
anymore, but the transition period from old EH where we needed it is
long gone already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At the moment libata doesn't pass pm_message_t down ata_device_suspend.
This causes drives to be powered down when we just want a freeze,
causing unnecessary wear and tear. This patch gets pm_message_t passed
down so that it can be used to determine whether to power down the
drive.
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
drivers/scsi/libata-core.c | 5 +++--
drivers/scsi/libata-scsi.c | 4 ++--
drivers/scsi/scsi_sysfs.c | 2 +-
include/linux/libata.h | 4 ++--
include/scsi/scsi_host.h | 2 +-
5 files changed, 9 insertions(+), 8 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This allows the removal of the contained flag and also does a bit of
class renaming (sas_rphy->sas_device).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original from Christoph Hellwig and Eric Moore. This version exports
the scsi_reprobe_device() function as an inline.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch makes expanders appear as labelled objects with properties in
the SAS tree.
I've also modified the phy code to make expander phys appear labelled by
host number, expander number and phy index.
So, for my current config, you see something like this in sysfs:
/sys/class/scsi_host/host1/device/phy-1:4/expander-1:0/phy-1-0:12/rphy-1:0-12/target1:0:1
And the expander properties are:
jejb@sparkweed> cd /sys/class/sas_expander/expander-1\:0/
jejb@sparkweed> for f in *; do echo -n $f ": "; cat $f; done
component_id : 29024
component_revision_id : 4
component_vendor_id : VITESSE
device : cat: device: Is a directory
level : 0
product_id : VSC7160 Eval Brd
product_rev : 4
uevent : cat: uevent: Permission denied
vendor_id : VITESSE
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This moves the eh_timed_out functionality from the scsi_host_template
to the transport_template. Given that this is now a transport function,
the EH_RESET_TIMER case no longer caps the timer reschedulings. The
transport guarantees that this is not an infinite condition.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Begin introducing the concept of sas remote devices that have an rphy
embedded. The first one (this) is a simple end device. All that an
end device really does is have port mode page parameters contained.
The next and more complex piece will be expander remote devices.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I don't think these exist in silicon yet, but the aic94xx driver has a
register setting for them.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In order to use the new execute_in_process_context() API, you have to
provide it with the work storage, which I do in SCSI in scsi_device and
scsi_target, but which also means that we can no longer queue up the
target reaps, so instead I moved the target to a state model which
allows target_alloc to detect if we've received a dying target and wait
for it to be gone. Hopefully, this should also solve the target
namespace race.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some non-standard SCSI targets or protocols, such as USB UFI, report "no
LUN present" by setting the Peripheral Device Type to 0x1f and the
Peripheral Qualifier to 0 (not 3 as the standard requires) in the INQUIRY
response. This patch (as650b) adds a new target flag and code to
accomodate such targets.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Introduce new helpers:
- spi_populate_width_msg()
- spi_populate_sync_msg()
- spi_populate_ppr_msg()
and use them in drivers which already enable the SPI transport.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As devfs has been disabled from the kernel tree for a number of months
now (5 to be exact), here's a patch against 2.6.16-rc1-git1 that removes
support for it from the SCSI subsystem.
The patch also removes the scsi_disk devfs_name field as it's no longer
needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We have several points in the SCSI stack (primarily for our device
functions) where we need to guarantee process context, but (given the
place where the last reference was released) we cannot guarantee this.
This API gets around the issue by executing the function directly if
the caller has process context, but scheduling a workqueue to execute
in process context if the caller doesn't have it. Unfortunately, it
requires memory allocation in interrupt context, but it's better than
what we have previously. The true solution will require a bit of
re-engineering, so isn't appropriate for 2.6.16.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From:
michaelc@cs.wisc.edufujita.tomonori@lab.ntt.co.jpda-x@monatomic.org
and err path fixup from:
ogerlitz@voltaire.com
This patch cleans up that interface by having the lld and class
pass a iscsi_cls_session or iscsi_cls_conn between each other when
the function is used by HW and SW iscsi llds. This way the lld
does not have to remember if it has to send a handle or pointer
and a handle or pointer to connection, session or host.
This also has the class verify the session handle that gets passed from
userspace instead of using the pointer passed into the kernel directly.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Export two SCSI EH command handling functions. To be used by libata EH.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When the scsi_execute_async interface was added it ended up reducing
the flexibility of userspace to send arbitrary scsi commands through
sg using SG_IO. The SG_IO interface allows userspace to specify the
CDB length. This is now ignored in scsi_execute_async and it is
guessed using the COMMAND_SIZE macro, which is not always correct,
particularly for vendor specific commands. This patch adds a cmd_len
parameter to the scsi_execute_async interface to allow the caller
to specify the length of the CDB.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After the recent overhaul of the block layer the variable
"ordered_flush" is no longer used.
Signed-off-by: Tetsuo Takata <takatatt@intellilink.co.jp>
Signed-off-by: Jens Axboe <axboe@suse.de>
On alpha:
In file included from drivers/scsi/sym53c8xx_2/sym_glue.h:59,
from drivers/scsi/sym53c8xx_2/sym_fw.c:40:
include/scsi/scsi_transport_spi.h:57: error: field `dv_mutex' has incomplete type
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the second version of the patch to address Christoph's comments.
Instead of doing the lib, I just kept everything in scsi_trnapsort_iscsi.c
like the FC and SPI class. This was becuase the driver model and sysfs
class is tied to the session and connection setup so separating did not
buy very much at this time.
The reason for this patch was becuase HW iscsi LLDs like qla4xxx cannot
use the iscsi class becuase the scsi_host was tied to the interface and
class code. This patch just seperates the session from scsi host so
that LLDs that allocate the host per some resource like pci device
can still use the class.
This is also fixes a couple refcount bugs that can be triggered
when users have a sysfs file open, close the session, then
read or write to the file.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When James Smart fixed the issue of the userspace scan atributes
crashing the system with the FC transport class he added a patch to
let the transport class check if the parent is valid for a given
transport class.
When adding support for the integrated raid of fusion sas devices
we ran into a problem with that, as it didn't allow adding virtual
raid volumes without the transport class knowing about it.
So this patch adds a user_scan attribute instead, that takes over from
scsi_scan_host_selected if the transport class sets it and thus lets
the transport class control the user-initiated scanning. As this
plugs the hole about user-initiated scanning the target_parent hook
goes away and we rely on callers of the scanning routines to do
something sensible.
For SAS this meant I had to switch from a spinlock to a mutex to
synchronize the topology linked lists, in FC they were completely
unsynchronized which seems wrong.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert the SCSI transport class code to use a mutex rather than a
semaphore.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add fc_host attribute permanent_port_name which is
used to show the port name of the primary port -
the port that initially logged into the fabric.
For a virtual port (registered via the primary port with
FDISC command) it is useful to know not only its (virtual)
port name but also the permanent port name.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
LLDDs should never see REQ_BLOCK_PC requests, we can handle them just
fine in the core code. There is a small behaviour change in that some
check in sr's rw_intr are bypassed, but I consider the old behaviour
a bug.
Mike found this cleanup opportunity and provdided early patches, so all
the credit goes to him, even if I redid the patches from scratch beause
that was easier than forward-porting the old patches.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
the scsi layer is using semaphores in a mutex way, this patch converts
these into using mutexes instead
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds suspend patch to libata, and ata_piix in particular. For
most low level drivers, they should just need to add the 4 hooks to
work. As I can only test ata_piix, I didn't enable it for more
though.
Suspend support is the single most important feature on a notebook, and
most new notebooks have sata drives. It's quite embarrassing that we
_still_ do not support this. Right now, it's perfectly possible to
suspend the drive in mid-transfer.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All ordered request related stuff delegated to HLD. Midlayer
now doens't deal with ordered setting or prepare_flush
callback. sd.c updated to deal with blk_queue_ordered
setting. Currently, ordered tag isn't used as SCSI midlayer
cannot guarantee request ordering.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
In the scenario that a link was broken, the devloss timer for each
rport was expire at roughly the same time, causing lots of "delete"
workqueue items being queued. Depth is dependent upon the number of
rports that were on the link.
The rport target remove calls were calling flush_scheduled_work(),
which would interrupt the stream, and start the next workqueue item,
which did the same thing, and so on until recursion depth was large.
This fix stops the recursion in the initial delete path, and pushes it
off to a host-level work item that reaps the dead rports.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rename scsi_print_msg to spi_print_msg and move its prototype from
scsi_dbg.h to scsi_transport_spi.h
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This merge is pretty extensive. The conflict is over the new
req->retries parameter, so I had to change the prototype to
scsi_setup_blk_pc_cmnd() and the usage in sd, sr and st.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add scsi helpers to create really-large-requests and convert
scsi-ml to scsi_execute_async().
Per Jens's previous comments, I placed this function in scsi_lib.c.
I made it follow all the queue's limits - I think I did at least :), so
I removed the warning on the function header.
I think the scsi_execute_* functions should eventually take a request_queue
and be placed some place where the dm-multipath hw_handler can use them
if that failover code is going to stay in the kernel. That conversion
patch will be sent in another mail though.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This follows on from Jens' patch and consolidates all of the ULD
separate handlers for REQ_BLOCK_PC into a single call which has his
fix for our direction bug.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add forward declarations to allow scsi_transport_spi.h to be compiled by
itself.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make the vendor, model and rev fields in scsi_device pointers to const
and update a few prototypes of functions using them.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_send_eh_cmnd currently uses a semaphore and an overload of eh_timer
to either get a completion for a command for a timeout.
Switch to using a completion and wait_for_completion_timeout to simply
the code and not having to deal with the races ourselves.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This function has been superceeded by the block request based interfaces
and is unused (except for the uncompilable cpqfc driver).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
now that the abuse in qla2xxx is gone this field can be remove.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add an InfiniBand SCSI RDMA Protocol (SRP) initiator. This driver is
used to talk talk to InfiniBand SRP targets (storage devices).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We recently went back to implement a board reset. When we perform the
reset, we wanted to tear down the internal data structures and rebuild
them. Unfortunately, when it came to the rport structure, things were
odd. If we deleted them, the scsi targets and sdevs would be
torn down. Not a good thing for a temporary reset. We could block the
rports, but we either maintain the internal structures to keep the
rport reference (perhaps even replicating what's in the transport),
or we have to fatten the fc transport with new search routines to find
the rport (and deal with a case of a dangling rport that the driver
forgets).
It dawned on me that we had actually reached this state incorrectly.
When the fc transport first started, we did the block/unblock first, then
added the rport interface. The purpose of block/unblock is to hide the
temporary disappearance of the rport (e.g. being deleted, then readded).
Why are we making the driver do the block/unblock ? We should be making
the transport have only an rport add/delete, and the let the transport
handle the block/unblock.
So... This patch removes the existing fc_remote_port_block/unblock
functions. It moves the block/unblock functionality into the
fc_remote_port_add/delete functions. Updates for the lpfc driver are
included. Qlogic driver updates are also enclosed, thanks to the
contributions of Andrew Vasquez. [Note: the qla2xxx changes are
relative to the scsi-misc-2.6 tree as of this morning - which does
not include the recent patches sent by Andrew]. The zfcp driver does
not use the block/unblock functions.
One last comment: The resulting behavior feels very clean. The LLDD is
concerned only with add/delete, which corresponds to the physical
disappearance. However, the fact that the scsi target and sdevs are
not immediately torn down after the LLDD calls delete causes an
interesting scenario... the midlayer can call the xxx_slave_alloc and
xxx_queuecommand functions with a sdev that is at the location the
rport used to be. The driver must validate the device exists when it
first enters these functions. In thinking about it, this has always
been the case for the LLDD and these routines. The existing drivers
already check for existence. However, this highlights that simple
validation via data structure dereferencing needs to be watched.
To deal with this, a new transport function, fc_remote_port_chkready()
was created that LLDDs should call when they first enter these two
routines. It validates the rport state, and returns a scsi result
which could be returned. In addition to solving the above, it also
creates consistent behavior from the LLDD's when the block and deletes
are occuring.
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New dev_printk wrappers, which allow us to shrink code, and
eliminate direct references to host/channel/id/lun members:
scmd_printk()
Introduce wrappers for highly common idioms, which may also help us
eliminate some ->{channel,id} references in the future:
{scmd,sdev}_id()
{scmd,sdev}_channel()
The scmd_* wrappers are present in scsi/scsi_device.h because they all
employ the dereference chain cmd->device->$member. We would prefer to
use static inline functions rather than macros, but that would have a
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Ok, here's a patch to add such a common API for fc transport users.
Relevant LLD changes (lpfc and qla2xxx) also present.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add a flag to mark a PHY as attached to the HBA as opposed to beeing on
an expander. This is needed because various features are only supported
on those. This is a crude hack, the proper fix would be to use
different classes for host-attached vs expander phys. I'm looking into
that.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For now supporting the ->get_linkerrors method is mandatory. I'll
probably be beaten to implement the .show_foo variables and different
types of attributes soon..
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This should eliminate (at least in the mid layer) to make numeric
assumptions about any of the enumeration variables. As a side effect,
it will also make all the messages consistent and line us up nicely for
the error logging strategy (if it ever shows itself again).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently we just ignore the device, which means there are a few
arrays out there that we don't find.
This patch updates the scsi_report_lun_scan() to take a target instead
of a device so it can be called on a return of
SCSI_SCAN_TARGET_PRESENT, which is what a PQ 3 device returns.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: hare@suse.de
for a proper alignment between open-iscsi and iscsitarget the
definitions in include/iscsi_proto.h do not match exactly.
With this patch it's possible to have iscsitarget use
'include/iscsi_proto.h' instead of its own iscsi_hdr.h.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: michaelc@cs.wisc.edu
Cleanup some iscsi_proto defs, add some missing values, and
fix some defs.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Alan Stern <stern@rowland.harvard.edu>
This patch (as561) fixes the error handler's thread-exit code. The
kthread_stop call won't wake the thread from a down_interruptible, so
the patch gets rid of the semaphore and simply does
set_current_state(TASK_INTERRUPTIBLE);
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Modified to simplify the termination loop and correct the sleep condition.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We fix the oops by enforcing the host state model. There have also
been two extra states added: SHOST_CANCEL_RECOVERY and
SHOST_DEL_RECOVERY so we can take the model through host removal while
the recovery thread is active.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
obviously FC Port Speeds in scsi_transport_fc.h are defined according
to FC-HBA:
#define FC_PORTSPEED_1GBIT 1
#define FC_PORTSPEED_2GBIT 2
#define FC_PORTSPEED_10GBIT 4
#define FC_PORTSPEED_4GBIT 8
Problem is, whoever invented FC-HBA did not care about FC-FS or
FC-GS-x. Following FC-FS/FC-GS-x defintions of port speeds would look
like:
1 GBit: 0x0001
2 GBit: 0x0002
4 GBit: 0x0004
10GBit: 0x0008
(and new in FC-LS:
8 Gbit: 0x0010
16GBit: 0x0020)
I really appreciate if scsi_transport_fc.h would define port speeds
according to FC-GS-x/FC-FS. Thus mapping of port speed capabilities to
values defined in scsi_transport_fc.h can be avoided in the LLDD.
Attached is a patch to change the definitions.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The original API returned either an ERR_PTR() or a refcounted sdev.
Unfortunately, if it's successful, you need to do a scsi_device_put() on
the sdev otherwise the refcounting is wrong.
Everyone seems to expect that scsi_add_device() should be callable
without doing the ref put, so alter the API so it is (we still have
__scsi_add_device with the original behaviour).
The only actual caller that needs altering is the one in firewire ...
not because it gets this right, but because it acts on the error if one
is returned.
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On some platforms the hard-casting of 8 byte node_name and
port_name arrays to an u64 would cause unaligned-access
warnings. Generalize the conversions with a transport
helper function which performs consistent shifting of WWN
bytes.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SAS transport class contains common code to deal with SAS HBAs, an
aproximated representation of SAS topologies in the driver model,
and various sysfs attributes to expose these topologies and managment
interfaces to userspace.
In addition to the basic SCSI core objects this transport class introduces
two additional intermediate objects: The SAS PHY as represented by struct
sas_phy defines an "outgoing" PHY on a SAS HBA or Expander, and the SAS
remote PHY represented by struct sas_rphy defines an "incoming" PHY on a
SAS Expander or end device. Note that this is purely a software concept, the
underlying hardware for a PHY and a remote PHY is the exactly the same.
There is no concept of a SAS port in this code, users can see what PHYs
form a wide port based on the port_identifier attribute, which is the same
for all PHYs in a port.
This submission doesn't handle hot-plug addition or removal of SAS devices
and thus doesn't do scanning in a workqueue yet, that will be added in
phase2 after this submission. In a third phase I will add additional
managment infrastructure.
I think this submission is ready for 2.6.14, but additional comments are
of course very welcome.
I'd like to thanks James Smart a lot for his very useful input on the
design.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This one removes struct scsi_request entirely from sd. In the process,
I noticed we have no callers of scsi_wait_req who don't immediately
normalise the sense, so I updated the API to make it take a struct
scsi_sense_hdr instead of simply a big sense buffer.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This one's slightly more difficult. The transport class uses
REQ_FAILFAST, so another interface (scsi_execute) had to be invented to
take the extra flag. Also, the sense functions are shifted around to
allow spi_execute to place data directly into a struct scsi_sense_hdr.
With this change, there's probably a lot of unnecessary sense buffer
allocation going on which we can fix later.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After this, we just have some drivers, all the ULDs and the SPI
transport class using scsi_wait_req().
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original From: Mike Christie <michaelc@cs.wisc.edu>
Add scsi_execute_req() as a replacement for scsi_wait_req()
Fixed up various pieces (added REQ_SPECIAL and caught req use after
free)
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch is necessary if we begin exposing underlying physical disks
(which can attach to the SPI transport class) of the hardware RAID
cards, since we don't want any SPI parameters binding to the RAID
devices.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
