In the lastest OMAP4 hwmod data file, the _hwmod was removed
in order to save some memory space and because it does not
bring a lot.
The same cleanup will be have to done for other hwmods in
OMAP2 & 3 data files.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
During the _init_clocks phase, the iteration is stopped but the
status is still change from _HWMOD_STATE_REGISTERED to
_HWMOD_STATE_CLKS_INITED.
Since the _setup phase will be done nevertheless, it might be
better to keep initializing the others clocks nodes and just
keep the warning.
It is much easier to debug when a important number of clocks
name are wrong during the early debug phase of a new platform.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The WARN is a little bit too verbose and is not providing
usefull information in that case.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The previous clock API was returning a standard linux error code in
case of failure. This is not the case anymore with the new
omap_clk_get_by_name API. A NULL value means that the clock node
does not exist.
Replace all the IS_ERR check by a !clk check.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The iteration is currently done on the omap_hwmod_ocp_if pointer
and not on the table pointer that reference them.
It worked most of the time because the structure are contiguous in
memory.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some initiator modules in OMAP2 & 3 does not have IDLEST bit,
in that case we cannot detect the module readiness by
polling that bit and must exist the function immediately
assuming that the module is ready.
The previous flag was affected to the OCP interface. While it is
technically true that the idlest is related to the L4 slave
interface of the module, the PRCM status belong to the module.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The return of the omap4_cm_wait_module_ready function is checked
in order to avoid accessing the sysconfig register if the module is
not in the correct state.
In that case the _setup will exit without trying to reset
using sysconfig.
For the moment a warning is printed. A proper management of fclk
and module reset will have to be done in order to init correctly
the problematic IPs listed below.
<4>omap_hwmod: ivahd: cannot be enabled (3)
<4>omap_hwmod: iss: cannot be enabled (3)
<4>omap_hwmod: tesla: cannot be enabled (3)
<4>omap_hwmod: sdma: cannot be enabled (3)
<4>omap_hwmod: sl2: cannot be enabled (3)
<4>omap_hwmod: sad2d: cannot be enabled (3)
<4>omap_hwmod: ducati: cannot be enabled (3)
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The maximum timeout to wait for the PRCM to request that a module
exit idle or reach functionnal state is common to OMAP2/3/4 SoCs,
so, move it to the chip family-common cm.h include file.
Reduce the timeout from 20 ms to 2 ms.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Accessing the clkctrl register using offset of module & device is hard
to do in OMAP4 due to the way the CM1, CM2, PRM and PRCM_MPU are located
in the address space. There is no common base address anymore for all the
CM registers.
The easiest way to handle that on OMAP4 is to provide the absolute address
of the XXX_CLKCTRL register per hwmod.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Clean up comment style, remove unnecessary includes, and resolve some
checkpatch warnings in plat-omap/clock.c.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 678bc9a2ea split dpll4_m2_ck,
creating a 34xx and a 36xx variant, to handle the additional 16
divider steps provided on the 36xx. This in turn required dynamic
rewriting of the clock tree during initialization, which is
undesirable. All this seems to be unnecessary, though, since the
additional 16 divider steps can simply be marked with RATE_IN_36XX.
This patch does so and re-merges the affected structures.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Vishwanath Sripathy <vishwanath.bs@ti.com>
Rename the RATE_IN_343X clksel_rate.rate flag to be RATE_IN_3XXX, to reflect
that these rates are valid on all OMAP3 platforms, not just 343X.
Also rename the RATE_IN_OMAP3430ES2 clksel_rate.rate flag to be
RATE_IN_OMAP3430ES2PLUS, to reflect that these flags are valid on all
OMAP3 platforms after 3430ES2.
This patch should not result in any functional changes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
This patch cleans up arch/arm/mach-omap2/clkt_clksel.c. It:
- makes several functions static that are not called outside the file;
- adds documentation;
- makes some code paths easier to read (hopefully), by breaking up
compound statements and removing redundant checks;
- converts some pr_err()s that indicate clock tree data problems into WARN()s,
so they are more likely to be noticed;
- and moves omap2_clk_round_rate() back into mach-omap2/clock.c, its proper
home, since it is not clksel-specific.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The DEFAULT_RATE clksel_rate flag is essentially useless. It was set
on some of the lowest divisors, which, when switching to a much
higher-rate parent, could have potentially resulted in rates that
exceeded the hardware specifications for downstream clocks in the
window between the clk_set_parent(), and a subsequent clk_set_rate().
It seems much safer to just remove the flag and always use the highest
available divisor (resulting in the lowest possible rate) after the
switch, and this patch does so.
Ideally, it would be best to first attempt to switch to a divisor that
matches the clock's rate with the previous parent, if at all possible.
But that is a project for some other day or some other person. The
parent changing code is rarely used.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Writes to the PM_*GRPSEL registers should use _GRPSEL_ macros, not _EN_ macros,
to match the TRM and guard against inadvertent error. This patch should
not cause any functional change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jouni Högander <jouni.hogander@nokia.com>
Fix all of the remaining PRCM register shift/bitmask macros that did not
use the _SHIFT/_MASK suffixes to use them. This makes the use of these
macros consistent. It is intended to reduce error, as code can be inspected
visually by reviewers to ensure that bitshifts and bitmasks are used in
the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Fix all of the remaining OMAP3 PRCM register shift/bitmask macros that
did not use the _SHIFT/_MASK suffixes to use them. This makes the use
of these macros consistent. It is intended to reduce error, as code
can be inspected visually by reviewers to ensure that bitshifts and
bitmasks are used in the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Fix all of the remaining OMAP2 PRCM register shift/bitmask macros that
did not use the _SHIFT/_MASK suffixes to use them. This makes the use
of these macros consistent. It is intended to reduce error, as code
can be inspected visually by reviewers to ensure that bitshifts and
bitmasks are used in the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
remove the section annotation from omap1_clk_disable_unused()
to kill the section mismatch warning.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
- Update the omap3_defconfig to sync up with the generated .config
- Increase CONFIG_LOG_BUF_SHIFT to 16 to allow the entire
boot log to be captured
(useful when using boot time tracer, for example)
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In OMAP4, MMC1 PBIAS and its associated IO is software-controlled
by CONTROL_PBIAS and CONTROL_MMC1 registers. This patch adds PBIAS
configuration for MMC1 Controller during power-ON and power-OFF
of regulator.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding support for MMC1 & MMC2 controllers of OMAP4430 SDP
to board file.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch enables RTC and regulator support on omap4430 sdp
platform. Also sync up the defconfig with latest kernel
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds i2c1 peripherals data to
omap4430 sdp board file.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the i2c board support for OMAP4430 SDP platform.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are three i2c buses on am3517, and each i2c bus has several devices
on it, so we can't name the i2c boardinfo structures with one of these
devices. In order to make it more readable, now rename these three boardinfo
structures based on i2c indexes.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Acked-By: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Access to some of the OMAP4 GPIO registers are not properly handled.
This patch fixes it.
This patch is tested on 3430SDP and 4430SDP boards
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves OMAP4 soc specific code from 4430sdp board file.
The change is necessary so that newer board support can be added
with minimal changes. This will be also problematic for
multi-board, multi-omap builds.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3517 don't have the register OMAP343X_CONTROL_PBIAS_LITE and the regulators
like "vmmc", so we set a noop "set_power" function for it.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is two gpio for mmc use, one is for card detecting, another is
used for checking write protect. Intialize its pinmux in case the bootloader
doesn't set it.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Multi line comments are fixed as per CodingStyle
guidelines.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If we are softbooting another kernel using kexec, DMA controller state is not
known when we are performing omap_init_dma(). It is possible that some DMA
channels are already active. For example after kexec we get:
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
To prevent any weird things happening, we disable all channel interrupts during
init.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SDI Display subsystem needs access to the vdds_sdi supply
regulator. This is TWL4030's VAUX1 supply on RX-51.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The patch adds a CONFIG directive required for supporting the Amstrad Delta
connected external keyboard by default.
Created and tested against linux-omap master,
commit 104a77440f05430f29f9d3f4ecb88c1536819585 dated 2010-04-27.
Works on top of PATCH v4 4/5(7), "input: serio: add support for Amstrad Delta
serial keyboard port".
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
EHCI port on UI card and LCD share two pins (GPIO 181 and 182) thus
they have to be mutually exclusive.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Upcoming change to tlv320aic3x codec driver require four supplies.
Implement this by connecting analogic supplies to TWL4030 VMMC2 and digital
supplies to TWL4030 VIO.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This makes possible to probe the audio codec and add another i2c2
components in the future.
Fix also indentation for the first omap_register_i2c_bus.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I believe the VMMC2 constraints must be the same than with VAUX3. Older
boards are using TWL4030 VMMC2 supply for internal MMC whereas newer are
using VAUX3 that has more limited constraints defined in this same file.
More over, the VMMC2 supply is used also for analog audio domain and the
miminum analog voltage of the TLV320AIC34 codec is 2.7 V.
To combine these two facts, the patch changes supply name to V28_A as the
newer boards register VMMC2_30 for VAUX3 and uses the same constraints than
VAUX3 since those constraints are ok for the TLV320AIC34.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some Overo add-on boards include a second ethernet port. This patch
adds support for that second port.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the default configuration for AM3517EVM to enable
support for EMAC peripheral.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The emac driver currently uses Davinci clock names for the module and phy
clocks. Updated the omap3xxx_clks table to match the names
used by the Davinci emac driver.
Note that eventually the EMAC clocks should be renamed to be generic.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated patch description to match the patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Modify the default kernel configuration on AM3517 to enable CAN.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the new default configuration for the Devkit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Configuration for OMAP2430 should select ARCH_OMAP_OTG just like
it is done for OMAP2420
Signed-off-by: Viral Mehta <viral.mehta@lntinfotech.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform init code for OHCI USB on OMAP2430 SDP
Signed-off-by: Viral Mehta <viral.mehta@lntinfotech.com>
[tony@atomide.com: Updated subject to mention the board name]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch provides the following ams_delta_defconfig updates:
- explicitly select preemptable RCU,
- replace outdated CONFIG_LBD and CONFIG_LSF options with CONFIG_LBDAF,
- activate support for LCD contrast setting (new in 2.6.34),
- turn off verbose bug reporting for smaller kernel.
Created and tested against linux-2.6.34-rc3.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (250 commits)
ALSA: hda: Storage class should be before const qualifier
ASoC: tpa6130a2: Remove CPVSS and HPVdd supplies
ASoC: tpa6130a2: Define output pins with SND_SOC_DAPM_OUTPUT
ASoC: sdp4430 - add sdp4430 pcm ops to DAI.
ASoC: TWL6040: Enable earphone path in codec
ASoC: SDP4430: Add support for Earphone speaker
ASoC: SDP4430: Add sdp4430 machine driver
ASoC: tlv320dac33: Avoid powering off while in BIAS_OFF
ASoC: tlv320dac33: Use dev_dbg in dac33_hard_power function
ALSA: sound/pci/asihpi: Use kzalloc
ALSA: hdmi - dont fail on extra nodes
ALSA: intelhdmi - add id for the CougarPoint chipset
ALSA: intelhdmi - user friendly codec name
ALSA: intelhdmi - add dependency on SND_DYNAMIC_MINORS
ALSA: asihpi: incorrect range check
ALSA: asihpi: testing the wrong variable
ALSA: es1688: add pedantic range checks
ARM: McBSP: Add support for omap4 in McBSP driver
ARM: McBSP: Fix request for irq in OMAP4
OMAP: McBSP: Add 32-bit mode support
...
* 'for-linus/i2c-2635' of git://git.fluff.org/bjdooks/linux: (21 commits)
i2c-highlander: remover superflous variable
i2c-ibm-iic: drop NO_IRQ
i2c-cpm: drop NO_IRQ
i2c-mpc: drop NO_IRQ
MAINTAINERS: add i2c tree for embedded platforms
i2c-pxa: only define 'blue_murder'-function if DEBUG is #defined
i2c-pxa: remove unused macro
i2c-nomadik: fix operator precedence warning
i2c-nomadik: release region when removed
OMAP3: I2C: Clean up Errata 1p153 handling
OMAP2/3: I2C: Errata ID i207: Clear wrong RDR interrupt
omap: i2c: add a timeout to the busy waiting
omap: i2c: make errata 1.153 workaround a separate function
i2c-omap: add mpu wake up latency constraint in i2c
omap: i2c: Add i2c support on omap4 platform
i2c-bfin-twi: return completion in interrupt for smbus quick transfers
i2c-bfin-twi: remove redundant retry
i2c-bfin-twi: fix lost interrupts at high speeds
i2c-bfin-twi: add debug output for error status
i2c-bfin-twi: integrate timeout timer with completion interface
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
Add support for wakeup-mask style interrupts that share a
single mask register for various different interrupts. This
registers a set of interrupt->bit mappings and the register
they belong to.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change local_irq disable calls to use spinlocks to ensure that the
ADC driver data is protected against multiple access..
Note, this does not protect the client's data, and the client should
ensure it does not make multiple calls to the ADC driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the new locking calls to ensure that these are always exclusively
accessing the GPIO registers.
Fixes a possible race between two threads modifying the same GPIO bank,
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ensure the ADC device is touched only if S3C_DEV_ADC
is selected.
Fixes:
arch/arm/mach-s5pv210/built-in.o: In function `s5pv210_map_io':
/home/kgene/bjdooks/arch/arm/mach-s5pv210/cpu.c:92: undefined reference to `s3c_device_adc'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fixup commit 5cfc8ee0bb which
introduced ARCH_USES_GETTIMEOFFSET but missed out several
S5P architectures.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds support for Watchdog timer for Samsung S5PV210.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds support for Watchdog timer for Samsung S5P6440.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds support for Watchdog timer for Samsung S3C6410
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch moves the definitions of watchdog timer device from
plat-s3c24xx to plat-samsung. This will enable all Samsung S3C
and S5P series SoC's to use common WDT device definition.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This adds new machine definitions for the SmartQ 5 and 7.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Define platform devices for all audio devices found on S5PC100
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is for samsung GONI board using s5pc110.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds sdhci platform helpers required by sdhci-s3c driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds I2C platform helpers required by s3c2440-i2c driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds common framebuffer device helpers and register defines
for S5PV210 based machines.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds setup code for Samsung OneNAND controller driver. The
driver needs to be aware on which SoC it is running, so the actual
device id is being changed in cpu init code. S3C64xx SoCs have 2 OneNAND
controllers while S5PC100 and S5PC110 has only one.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[ben-linux@fluff.org: sort map.h entries]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch removes all obsolete files from plat-s5pc1xx. This directory is
no longer needed. S5PC100 SoC is now completely supported in plat-s5p
framework.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch moves support for gpio interrupts from plat-s5pc1xx to
mach-s5pc100 directory.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch moves S5PC100 SoC support to plat-s5p framework. Most
periperal support code has been already moved from plat-s5pc1xx to
mach-s5pc100.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move sdhci helpers from plat-s5pc1xx to mach-s5pc100.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds required platform definitions to enable s3c-fb
driver. Two framebuffer windows in 480x800x16bpp mode are defined.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add basic support for Samsung Aquila board. This board is based
on S5PC110 SoC.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The arch/arm/mach-s5pv210/Kconfig had a choice entry
to choose which of the two machines to build, which is
silly since you can easily build more than one machine
at a time.
Remove the choice entry so that both machines and any
future additions can all build in harmony.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch introduces nice defines for the initial values for UART devices
on SMDKC100.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The definition of the framebuffer parameters was created when s3c-fb.c
driver was patched to support setting the refresh rate directly (commit
600ce1a0fa). That patch was completely wrong
and was reverted in commit eb29a5cc0b what breaked the
framebuffer on s5pc100. This patch updates framebuffer definitions to
correct values.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for external interrupts on S5PV210.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Pannaga Bhushan <p.bhushan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: Ext => IRQ_EINT in title]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds touchscreen support for S5PV210.
Note: TSADC in S5PV210 support 2 touchscreen interfaces,
Only 1 is implemented as of now.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: minor title fix]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds touchscreen support for S5P6440.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: minor header fix]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds touchscreen support for S3C64XX.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: minor title fix]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
While waiting for completion of the i2c transfer, the
MPU could hit OFF mode and cause several msecs of
delay that made i2c transfers fail more often. The
extra delays and subsequent re-trys cause i2c clocks
to be active more often. This has also an negative
effect on power consumption.
Created a mechanism for passing and using the
constraint setting function in driver code. The used
mpu wake up latency constraints are now set individually
per bus, and they are calculated based on clock rate
and fifo size.
Thanks to Jarkko Nikula, Moiz Sonasath, Paul Walmsley,
and Nishanth Menon for tuning out the details of
this patch.
Updates by Kevin as requested by Tony:
- Remove omap_set_i2c_constraint_func() in favor of conditionally
adding the flag in omap_i2c_add_bus() in order to keep all the OMAP
conditional checking in a single location.
- Update set_mpu_wkup_lat prototypes to match OMAP PM layer so
OMAP PM function can be used directly in pdata.
Cc: Moiz Sonasath <m-sonasath@ti.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (48 commits)
Revert "rtc: omap: let device wakeup capability be configured from chip init logic"
DM365: Added more PINMUX configurations for AEMIF
DM365: Make CLKOUTx available
DM365: Added PINMUX definitions for GPIO30..32
Davinci: iotable based ioremap() interception
Davinci: pinmux - use ioremap()
Davinci: aintc/cpintc - use ioremap()
Davinci: psc - use ioremap()
Davinci: timer - use ioremap()
Davinci: jtag_id - use ioremap()
Davinci: da8xx: rtc - use ioremap
Davinci: gpio - use ioremap()
davinci: edma: fix coding style issue related to breaking lines
davinci: edma: use BIT() wherever possible
davinci: edma: fix coding style issue related to usage of braces
davinci: edma: use a more intuitive name for edma_info
Davinci: serial - conditional reset via pwremu
Davinci: serial - use ioremap()
Davinci: serial - remove unnecessary define
Davinci: watchdog reset separation across socs
...
Fix up trivial conflict in arch/arm/Kconfig due to removal of "select
GENERIC_TIME"
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (224 commits)
ARM: remove 'select GENERIC_TIME'
ARM: 6136/1: ARCH_REQUIRE_GPIOLIB selects GENERIC_GPIO
ARM: 6074/1: oprofile: convert from sysdev to platform device
ARM: 6073/1: oprofile: remove old files and update KConfig
ARM: 6072/1: oprofile: use perf-events framework as backend
ARM: 6071/1: perf-events: allow modules to query the number of hardware counters
ARM: 6070/1: perf-events: add support for xscale PMUs
ARM: 6069/1: perf-events: use numeric ID to identify PMU
ARM: 6064/1: pmu: register IRQs at runtime
ARM: Optionally allow ARMv6 to use 'normal, bufferable' memory for DMA
ARM: 6134/1: Handle instruction cache maintenance fault properly
ARM: nwfpe: allow debugging output to be configured at runtime
ARM: rename mach_cpu_disable() to platform_cpu_disable()
ARM: 6132/1: PL330: Add common core driver
ARM: 6094/1: Extend cache-l2x0 to support the 16-way PL310
ARM: Move memory mapping into mmu.c
ARM: Ensure meminfo is sorted prior to sanity_check_meminfo
ARM: Remove useless linux/bootmem.h includes
ARM: convert /proc/cpu/aligment to seq_file
arm: use asm-generic/scatterlist.h
...
This patch adds also the pin definition helpers in iomux-mx3.h
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move the arch/arm/mach-s3c64xx/dev-ts.c file to arch/arm/plat-samsung and
rename the Kconfig entry appropriately.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch implements cfg_gpio function for Samsung touchscreen.
And also modifies the H1940 machine respectively.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds the touchscreen platform device definition for S3C64XX boards.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This moves mach-s3c2410/include/mach/ts.h to plat-samsung/include/plat/ts.h in
order to prepare for s3c64xx support in the touchscreen driver.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move i2c helpers from plat-s5pc1xx to mach-s5pc100.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move frame buffer helpers from plat-s5pc1xx to mach-s5pc100.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch renames gpio related registers from s5pc1xx to s5pc100 to
better match the plat-s5p framework style. GPIO_MP* defines now used
anywhere thus has been removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move gpio-lib support from plat-s5pc1xx to mach-s5pc100. Only basic gpio
functionality is now supported. Gpio interrupts are disabled temporarly
and will be added later.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
GPIOlib helpers from plat-samsung already have functions for accessing
4bit gpio banks. This patch removes the duplicated functions from
plat-s5pc1xx/gpiolib.c.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is a pre-requisite clock patch for the plat-s5pc1xx to plat-s5p
movement. The patches that perform the movement of the code from
plat-s5pc1xx to plat-s5p (and mach-s5pc100) should also enable the
build for the mach-s5pc100/clock.c code.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Driver strength parameter can be changed not only on S5PC100 but also
on S5PV210/S5PC110 platforms, so move the helper functions to the common
plat-samsung directory.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds GPIOlib support for S5PV210.
Signed-off-by: Pannaga Bhushan <p.bhushan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Timer interrupts range was defined as 43-47, what overlaps with VIC0 range
(32-64). This was caused probably by a typo while the common interrupts
definition was refactored. This patch moves timer interrupt range to safe
area of 11-15 (just before uart range).
This fixes the commit 87aef30eb3
("ARM: S5P: Change S5P_TIMER_IRQ based to 11 for SAMSUNG S5P series.")
which meant to move these into the old (and previously reserved)
ISA space.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[ben-linux@fluff.org: update description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds DSS2 support to the beagleboard boardfile. DVI and
TV-out are supported.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add LCD, Boot-up logo, framebuffer console, Keypad
and Power button support
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The Touch controller and LCD Panel share the same SPI bus 1.
So, we need to define the touch controller in the SPI board info
else, the SPI bus will be contended due to invalid state of
Touch controller's Chip Select thus preventing the LCD panel
from working.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Adds basic support for LCD Panel on Nokia N900
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Define platform devices for all audio devices found on S5P6440
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Define platform devices for all audio devices found on S5P6442
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Define platform devices for all audio devices found on S5PV210
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The pm-gpio.c code was incrementing the gpio_nr from the nr_gpios
field and the bank-bank offset inside the loop, and also in the
for() loop with a ++.
Remove the ++, as the number is already at the next GPIO, thus
ensuring that we don't skip a gpio bank by accident.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
As part of the cleanup, remove the old macros mapping GPIO numbers
to the base of the register now we have gpiolib to manage the GPIO
mappings for us.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Update a couple of S3C24XX and S3C2412 files that are still
using the GPIO number to register mapping calls to get the
s3c_gpio_chip and use the base field from that.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Start cleaning up the numbering of GPIO banks by removing the old
bank start definitions currently being used by some of the header
files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Increase GPIOs number for S3C244X, and make S3C_GPIO_END
point to BANKJ end, otherwise gpiolib refuses to register
BANKJ
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[ben-linux@fluff.org: Move pm fix to new patch]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the S3C_FB_MAX_WIN to the platform data to avoid
having to include the registers with the platform data.
Set S3C_FB_MAX_WIN to 5, which is the maximum that any
of the current hardware can do and the cost of having
it set to this for all is minimal (at least for the
platform data case), then always leave this as the maximum
for the systems supported.
Also remove the inclusion of <mach/regs-fb.h> from
the device definition in arch/arm/plat-samsung
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the definition of the LCD clock bit, it is the TFT display
controller on bit 9, not the older STN on bit 10.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This adds the xusbxti clock to S3C64XX platform.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Samsung's Soc S5PV210 has three PL330 DMACs. First is dedicated for
Memory->Memory data transfer while the other two meant for data
transfer with peripherals.
Define and add latter two PL330 DMACs as platform devices on the
S5PV210 platform.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Samsung's Soc S5P6442 has two PL330 DMACs. First is dedicated for
Memory->Memory data transfer while the second is meant for data
transfer with peripherals.
Define and add the peripheral PL330 DMAC as platform device on the
S5P6442 platform.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Samsung's Soc S5P6440 has one PL330 DMAC.
Define and add the PL330 DMAC as platform device on the
S5P6440 platform.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Latest Samsung SoCs have one or more PL330 as their DMACs. This patch
implements the S3C DMA API for PL330 core driver.
The design has been kept as generic as possible while keeping effort to
add support for new SoCs to the minimum possible level.
Some of the salient features of this driver are:-
o Automatic scheduling of client requests onto DMAC if more than
one DMAC can reach the peripheral. Factors, such as current load
and number of exclusive but inactive peripherals that are
supported by the DMAC, are used to decide suitability of a DMAC
for a particular client.
o CIRCULAR buffer option is supported.
o The driver scales transparently with the number of DMACs and total
peripherals in the platform, since all peripherals are added to
the peripheral pool and DMACs to the controller pool.
For most conservative use of memory, smallest driver size and best
performance, we don't employ legacy data structures of the S3C DMA API.
That should not have any affect since those data structures are completely
invisible to the DMA clients.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch de-asserts the reset line that is connected to the USB
ULPI PHY on USB Host1.
This patch should be included with the original USB host enablement
set of patches of mx51 babbage hw, but was accidentily left out.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch moves RTC device definitions from mach-s3c64xx
to plat-samsung, to enable the other SoCs to use same device
definition.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The member "clock" of struct "sja1000_platform_data" is documented as
"CAN bus oscillator frequency in Hz" but it's actually used as the CAN
clock frequency, which is half of it. To avoid further confusion, this
patch fixes it by renaming the member to "osc_freq". That way, also
non mainline users will notice the change. The platform code for the
relevant boards is updated accordingly. Furthermore, pre-defined
values are now used for the members "ocr" and "cdr".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves ADC device definition to plat-samsung.
Because that is generic to the S3C64XX and S5P Series SoCs.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Seems like a typo, wrong setup leads to broken image on ipaq screen.
Signed-off-by: Mike Solovyev <ms@sk.2-ch.org>
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The ARCH_REQUIRE_GPIOLIB config option will select GPIOLIB which
in turn will select GENERIC_GPIO. Because of this, there is no
reason to do the select GENERIC_GPIO in arch/arm/Kconfig for the
architectures that have ARCH_REQUIRE_GPIOLIB.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In preparation for removing volatile from the atomic_t definition, this
patch adds a volatile cast to all the atomic read functions.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a reworking of an original patch posted by Aaro Koskinen:
oprofile does not work with PM, because sysdev_suspend() is done with
interrupts disabled and oprofile needs a mutex. Implementing oprofile
as a platform device solves this problem.
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable hardware perf-events if CPU_HAS_PMU and select
HAVE_OPROFILE if HAVE_PERF_EVENTS. If no hardware support
is present, OProfile will fall back to timer mode.
This patch also removes the old OProfile drivers in favour
of the code implemented by perf.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are currently two hardware performance monitoring subsystems in
the kernel for ARM: OProfile and perf-events. This creates the
following problems:
1.) Duplicate PMU accessor code. Inevitable code drift may lead to
bugs in one framework that are fixed in the other.
2.) Locking issues. OProfile doesn't reprogram hardware counters
between profiling runs if the events to be monitored have not been
changed. This means that other profiling frameworks cannot use the
counters if OProfile is in use.
3.) Due to differences in the two frameworks, it may not be possible to
compare the results obtained by OProfile with those obtained by perf.
This patch removes the OProfile PMU driver code and replaces it with
calls to perf, therefore solving the issues mentioned above.
The only userspace-visible change is the lack of SCU counter support
for 11MPCore. This is currently unsupported by OProfile userspace tools anyway and therefore shouldn't cause any problems.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Jamie Iles <jamie.iles@picochip.com>
Cc: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For OProfile to initialise oprofilefs correctly, it needs to know
the number of counters it can represent.
This patch adds a function to the ARM perf-events backend to return
the number of hardware counters available for the current PMU.
Cc: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The perf-events framework for ARM only supports v6 and v7 cores.
This patch adds support for xscale v1 and v2 PMUs to perf, based on the
OProfile drivers in arch/arm/oprofile/op_model_xscale.c
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM perf-events framework provides support for a number of different
PMUs using struct arm_pmu. The char *name field of this struct can be
used to identify the PMU, but this is cumbersome if used outside of perf.
This patch replaces the name string for a PMU with an enum, which holds
a unique ID for the PMU being represented. This ID can be used to index
an array of names within perf, so no functionality is lost. The presence
of the ID field, allows other kernel subsystems [currently oprofile] to
use their own mappings for the PMU name.
Cc: Jean Pihet <jpihet@mvista.com>
Acked-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current PMU infrastructure for ARM requires that the IRQs for the PMU
device are fixed at compile time and are selected based on the ARCH_ or MACH_ flags. This has the disadvantage of tying the Kernel down to a
particular board as far as profiling is concerned.
This patch replaces the compile-time IRQ registration with a runtime mechanism which allows the IRQs to be registered with the framework as
a platform_device.
A further advantage of this change is that there is scope for registering
different types of performance counters in the future by changing the id
of the platform_device and attaching different resources to it.
Acked-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide a configuration option to allow the ARMv6 to use normal
bufferable memory for coherent DMA. This option is forced to 'y'
for ARMv7, and offered as a configuration option on ARMv6.
Enabling this option requires drivers to have the necessary barriers
to ensure that data in DMA coherent memory is visible prior to the
DMA operation commencing.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested on actual hardware using the g_ether and g_serial gadget drivers.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Eyebot robot needs the OTG port in host mode on the smartbot.
Add a new board definition so we can select the usb host/device
mode at boot with the mx31moboard_baseboard boot parameter.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In preparation for a new robot which needs the
OTG port as host.
This moves the OTG device registration into board
initialisation.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Acked-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Setup the pad with correct pull-up/down before doing the reset.
Assert the PHY enable signal so the reset is really done.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Acked-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
All other functions have the channel argument of type 'unsigned int'
the s3c2410_dma_devconfig also accept the same value as argument but
treat it as type 'int'. Remove this anomaly by make it 'unsigned int'.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add sclk clocks of type 'struct clksrc_clk' clock. The 'group2' of
clock clock sources is also added. This patch also changes the the
'id' member value of the uclk1 clock for instance instance 0 since
there are 4 instances of the uclk1 clock.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the sclk_audio(0/1/2) clocks and sclk_spdif clock of type
'struct clksrc_clk' clock. Also, add clk_pcmcdclk(0/1/2) clocks
of type 'struct clk' clock.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add sclk_dac, sclk_mixer and sclk_hdmi clocks. These clocks
are of type 'struct clksrc_clk' and so have a corresponding
clock list. These clocks are also added to the list of
clocks to be registered at boot time.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds the following system clocks.
1. clk_sclk_hdmiphy
2. clk_sclk_usbphy0
3. clk_sclk_usbphy1
4. sclk_dmc (dram memory controller clock)
5. sclk_onenand
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds the following.
1. Adds 'clk_sclk_hdmi27m' clock to represent the HDMI 27MHz clock.
2. Adds 'clk_vpllsrc; clock of type clksrc_clk to represent the
input clock for VPLL.
3. Adds 'clk_sclk_vpll' clock of type clksrc_clk to represent the
output of the MUX_VPLL mux.
4. Add clk_sclk_hdmi27m, clk_vpllsrc and clk_sclk_vpll to the list
of clocks to be registered.
5. Adds boot time print of 'clk_sclk_vpll' clock rate.
6. Adds 'clk_fout_vpll' clock to plat-s5p such that it is reusable
on other s5p platforms.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clk_p83 clock, which is the PCLK clock for PSYS domain, is of
type 'struct clk' whereas on S5PV210, this clock is suitable to be
of type clksrc_clk clock (since it has a clock divider). So this
patch replaces the 'struct clk' type clock to 'struct clksrc_clk'
type clock for the PCLK PSYS clock.
This patch modifies the following.
1. Removes definitions and usage of 'clk_p66' clock.
2. Adds 'clk_pclk_psys' clock which is of type 'struct clksrc_clk'.
3. Replaces all usage of clk_p66 with clk_pclk_psys clock.
4. Adds clk_pclk_psys into list of clocks to be registered.
5. Removes the sys_clks array since it is no longer required.
Also the registration of clocks in sys_clks is also removed.
6. Remove the 'GET_DIV' as it is no longer required.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clk_p83 clock, which is the PCLK clock for DSYS domain, is of
type 'struct clk' whereas on S5PV210, this clock is suitable to be
of type clksrc_clk clock (since it has a clock divider). So this
patch replaces the 'struct clk' type clock to 'struct clksrc_clk'
type clock for the PCLK DSYS clock.
This patch modifies the following.
1. Remove definitions and usage of 'clk_p83' clock.
2. Adds 'clk_pclk_dsys' clock which is of type 'struct clksrc_clk'.
3. Replace all usage of clk_p83 with clk_pclk_dsys clock.
4. Adds clk_pclk_dsys into list of clocks to be registered.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clk_h100 clock represents the IMEM clock for the MSYS domain.
This clock rate of this clock is always half of the hclk_msys clock.
There is an issue when getting the clock rate of the clk_h100 clock
(clock get_rate hclk_h100 always returns clock rate that is equal to
the hclk_msys clock rate).
This patch modifies the following.
1. Moves the definition of the clk_h100 clock into the 'init_clocks'
list with the appropriate parent, ctrlbit, enable and ops fields.
2. The name of the clock is changed from 'clk_h100' to 'hclk_imem'
to represent more clearly that is represents the IMEM clock in
the MSYS domain.
3. The function to get the clock rate of the hclk_imem clock is added.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clk_p100 clock, which is the PCLK clock for MSYS domain, is of
type 'struct clk' whereas on S5PV210, this clock is suitable to be
of type clksrc_clk clock (since it has a choice of clock source
and a pre-divider). So this patch replaces the 'struct clk' type
clock to 'struct clksrc_clk' type clock for the PCLK MSYS clock.
This patch modifies the following.
1. Remove definitions and usage of 'clk_p100' clock.
2. Adds 'clk_pclk_msys' clock which is of type 'struct clksrc_clk'.
3. Replace all usage of clk_p100 with clk_pclk_msys clock.
4. Adds clk_pclk_msys into list of clocks to be registered.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clk_h133 clock, which is the HCLK clock for PSYS domain, is of
type 'struct clk' whereas on S5PV210, this clock is suitable to be
of type clksrc_clk clock (since it has a choice of clock source
and a pre-divider). So this patch replaces the 'struct clk' type
clock to 'struct clksrc_clk' type clock for the HCLK PSYS clock.
This patch modifies the following.
1. Remove definitions and usage of 'clk_h133' clock.
2. Adds 'clk_hclk_psys' clock which is of type 'struct clksrc_clk'.
3. Replace all usage of clk_h133 with clk_hclk_psys clock.
4. Adds clk_hclk_psys into list of clocks to be registered.
5. Removes the clock rate calculation of hclk133 and replaces
it with code that derives the HCLK PSYS clock rate from
the clk_hclk_psys clock.
6. Modify printing of the system clock rates.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clk_h166 clock, which is the HCLK clock for DSYS domain, is of
type 'struct clk' whereas on S5PV210, this clock is suitable to be
of type clksrc_clk clock (since it has a choice of clock source
and a pre-divider). So this patch replaces the 'struct clk' type
clock to 'struct clksrc_clk' type clock for the HCLK DSYS clock.
This patch modifies the following.
1. Remove definitions and usage of 'clk_h166' clock.
2. Adds 'clk_sclk_a2m' clock which is one of possible parent clock
sources for the DSYS HCLK clock.
3. Adds 'clk_hclk_dsys' clock which is of type 'struct clksrc_clk'.
4. Replace all usage of clk_h166 with clk_hclk_dsys clock.
5. Adds clk_sclk_a2m and clk_hclk_dsys into list of clocks to
be registered.
6. Removes the clock rate calculation of hclk166 and replaces
it with code that derives the HCLK DSYS clock rate from
the clk_hclk_dsys clock.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clk_h200 represents the HCLK for the MSYS domain. This clock
is of type 'struct clk' but on V210, it is more suitable to be of
type 'struct clksrc_clk' (since it is a divided version of the
armclk). The replacement clock is renamed as clk_hclk_msys to
indicate that it represents the HCLK for MSYS domain.
This patch modifies the following.
1. Removes the usage of the clk_h200 clock.
2. Adds the new clock 'clk_hclk_msys'.
3. Adds clk_hclk_msys to the list of sysclks to be registered.
4. Modifies the hclk_msys clock rate calculation procedure to
be based on the new clk_hclk_msys clock.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch modifies the following.
1. Adds arm clock 'clk_armclk' of type clksrc_clk clock type.
2. Adds arm clock to the list of system clocks 'sysclks' for
registering it along with other system clocks.
3. Modifies the armclk clock rate calculation procedure to be
based on the new clk_armclk clock.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The assignment of clock rates for fout apll/mpll/epll is moved further
up in the s5pv210_setup_clocks function because the subsequent patches
require the clock rate of fout clocks to be setup.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch modifies the following.
1. Registers the mout_apll clksrc_clk clock.
2. The mout_mpll and mout_epll clocks were registered as 'struct clk'
types and then their parents were setup using the s3c_set_clksrc
function. This patch reduces the two steps into one by registering
the mout_mpll and mout_epll clocks using the s3c_register_clksrc
function.
3. As per point 2 above, the init_parents array is no longer required.
So the mout clocks are now put together in a new array named 'sysclks'.
The sysclks array will list the system level clocks and more
clocks will be added to it in the subsequent patches.
4. The clks array is left empty because of the movement of mpll and epll
clocks into the sysclks array. It is not deleted since subsequent
patches will add clocks into this array.
Signed-off-by: Thomas Abraham <thomas.ab <at> samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim <at> samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The system clock definitions are currently defined below the
peripheral clock definitions in the V210 clock code. For the V210
clock updates that follow this patch, it is required that the
system clock definitions such as the mout_apll and mout_mpll be
defined prior to the device clock definitions. This patch
re-arranges the system clock defintions for the clock updates that
follow this patch.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Between "clean D line..." and "invalidate I line" operations in
v7_coherent_user_range(), the memory page may get swapped out.
And the fault on "invalidate I line" could not be properly handled
causing the oops.
In ARMv6 "external abort on linefetch" replaced by "instruction cache
maintenance fault". Let's handle it as translation fault. It fixes the
issue.
I'm not sure if it's reasonable to check arch version in run-time.
Let's do it in compile time for now.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@nokia.com>
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enabling CONFIG_USER_DEBUG allows NWFPE to complain about every FP
exception, which with some programs can cause the kernel message log
to fill with NWFPE debug, swamping out other messages.
This change allows NWFPE debugging to be configured at run time.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PL330 is a configurable DMA controller PrimeCell device.
The register map of the device is well defined.
The configuration of a particular implementation can be
read from the six configuration registers CR0-4,Dn.
This patch implements a driver for the specification:-
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0424a/DDI0424A_dmac_pl330_r0p0_trm.pdf
The exported interface should be sufficient to implement
a driver for any DMA API.
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The L310 cache controller's interface is almost identical
to the L210. One major difference is that the PL310 can
have up to 16 ways.
This change uses the cache's part ID and the Associativity
bits in the AUX_CTRL register to determine the number of ways.
Also, this version prints out the CACHE_ID and AUX_CTRL registers.
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These files include linux/bootmem.h without using anything from this
file; remove the unnecessary include.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert code away from ->read_proc/->write_proc interfaces. Switch to
proc_create()/proc_create_data() which makes addition of proc entries
reliable wrt NULL ->proc_fops, NULL ->data and so on.
Problem with ->read_proc et al is described here commit
786d7e1612 "Fix rmmod/read/write races in
/proc entries"
This patch is part of an effort to remove the old simple procfs PAGE_SIZE
buffer interface.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6126/1: ARM mpcore_wdt: fix build failure and other fixes
ARM: 6125/1: ARM TWD: move TWD registers to common header
ARM: 6110/1: Fix Thumb-2 kernel builds when UACCESS_WITH_MEMCPY is enabled
ARM: 6112/1: Use the Inner Shareable I-cache and BTB ops on ARMv7 SMP
ARM: 6111/1: Implement read/write for ownership in the ARMv6 DMA cache ops
ARM: 6106/1: Implement copy_to_user_page() for noMMU
ARM: 6105/1: Fix the __arm_ioremap_caller() definition in nommu.c
DA8xx OHCI driver fails to load due to failing clk_get() call for the USB 2.0
clock. Arrange matching USB 2.0 clock by the clock name instead of the device.
(Adding another CLK() entry for "ohci.0" device won't do -- in the future I'll
also have to enable USB 2.0 clock to configure CPPI 4.1 module, in which case
I won't have any device at all.)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
McBSP module in OMAP4 needs to be able to set its tx/rx threshold
and enable the transmitter/receiver when starting an audio stream.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In OMAP4, there is only one irq line for TX and RX paths. Use
the correct irq line to avoid errors at runtime.
Also, request irq line only once (instead of requesting for TX
and RX).
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This rejects unaligned device virtual address('da') and physical
address('pa') and informs error to caller when a page table entry is
set. Otherwise, a wrong address can be used by IO device.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: Hari Kanigeri <h-kanigeri2@ti.com>
Searching avaialable spaces should be stopped as soon as it turns out
that there's no possibility with the rest of it.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Inserting a gap page between IOVMAs could detect an override on other
IOVMA with iommu fault. This was originally suggested by Sakari Ailus
and based on the work and comment by David Cohen.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: David Cohen <david.cohen@nokia.com>
Cc: Sakari Ailus <Sakari.Ailus@nokia.com>
This CONFIG_OMAP_IOMMU_DEBUG option cannot be selected because it's
not visible on menu. Make this option selectable.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
There are some places to scan iotlb entries. This iteration macro
could make these code a bit simpler with proceeding iotlb entries
transparently.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Tested-by: Hari Kanigeri <h-kanigeri2@ti.com>
This patch adds TLB preservation support to IOMMU module
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This patch provides the iommu support for OMAP4 co-processors.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This patch includes changes to omap3-iommu.c file to make it generic
for all OMAPs. Renamed omap3-iommu.c to omap-iommu.c
[Hiroshi DOYU: Remove unnecessary "iommu-y" in Makefile]
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
