Instead of disabling AN in loopback, just prevent restarting AN and
override the speed in sft9001_get_settings().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Early versions of the SFX7101 firmware could complete link training in
a state where it would not adequately cancel noise (Solarflare bug
10750). We previously worked around this by resetting the PHY after
seeing many Ethernet CRC errors. This workaround is unsafe since it
takes no account of the interval between errors; it also appears to
be unnecessary with production firmware. Therefore remove it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable a firmware option that appears to be necessary for reliable
operation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Printing anything over netconsole before hw is up and running is,
of course, not going to work.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
tulip: fix 21142 with 10Mbps without negotiation
drivers/net/skfp: if !capable(CAP_NET_ADMIN): inverted logic
gianfar: Fix Wake-on-LAN support
smsc911x: timeout reaches -1
smsc9420: fix interrupt signalling test failures
ucc_geth: Change uec phy id to the same format as gianfar's
wimax: fix build issue when debugfs is disabled
netxen: fix memory leak in drivers/net/netxen_nic_init.c
tun: Add some missing TUN compat ioctl translations.
ipv4: fix infinite retry loop in IP-Config
net: update documentation ip aliases
net: Fix OOPS in skb_seq_read().
net: Fix frag_list handling in skb_seq_read
netxen: revert jumbo ringsize
ath5k: fix locking in ath5k_config
cfg80211: print correct intersected regulatory domain
cfg80211: Fix sanity check on 5 GHz when processing country IE
iwlwifi: fix kernel oops when ucode DMA memory allocation failure
rtl8187: Fix error in setting OFDM power settings for RTL8187L
mac80211: remove Michael Wu as maintainer
...
with current kernels, tulip 21142 ethernet controllers fail to connect
to a 10Mbps only (i.e. without negotiation-partner) network. It used
to work in 2.4 kernels. Fix that. Tested on a 21142 Rev 0x11.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 0f0ca340e5 ("phy: power
management support") caused a regression in the gianfar driver.
Now phylib turns off PHY power during suspend, and thus WOL
doesn't work anymore.
This patch workarounds the issue by enabling wakeup in the MDIO
device, i.e. just restores the old behaviour for the gianfar
driver. Note that this way all PHYs on a given MDIO bus won't
be turned off during suspend, which isn't good from the power
saving point of view.
A proper, per netdevice wakeup management support will need
a bit reworked phylib suspend/resume logic.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a postfix decrement the timeout will reach -1 rather than 0,
so the warning will not be issued.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc9420 performs an interrupt signalling test when the interface is
brought up. The current code mistakenly sets its test flag to false
AFTER enabling the software interrupt source, making failure quite
likely.
This patch changes the code to set the test flag BEFORE enabling
interrupts. I've also removed an smp_wmb because the following spinlock
provides an implicit memory barrier.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit b31a1d8b41 ("gianfar: Convert
gianfar to an of_platform_driver") changes the gianfar's phy id to the
format like "mdio@xxxx:xx", but uec still uses the old format like
"xxxxxxxx:xx". For the board whose UEC uses gianfar-mdio like
MPC8568MDS, the phy can not be attached because of the incompatible
phy id format. This patch changes uec's phy id to the same format as
gianfar's.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Toralf Förster and Randy Dunlap.
- http://linuxwimax.org/pipermail/wimax/2009-January/000460.html
- http://lkml.org/lkml/2009/1/29/279
The definitions needed for the wimax stack and i2400m driver debug
infrastructure was, by mistake, compiled depending on CONFIG_DEBUG_FS
(by them being placed in the debugfs.c files); thus the build broke in
2.6.29-rc3 when debugging was enabled (CONFIG_WIMAX_DEBUG) and
DEBUG_FS was disabled.
These definitions are always needed if debug is enabled at compile
time (independently of DEBUG_FS being or not enabled), so moving them
to a file that is always compiled fixes the issue.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reducing jumbo ring size below 1024 reduces throughput for old
firmwares (3.4.216 and older) running on older (NX2031) chip,
so restore it back to 1024.
This was reduced in commit 32ec803348
("netxen: reduce memory footprint").
Raising jumbo ring size from 512 to 1024, adds ~4MB per port, but
there's still big saving because of original patch (~20MB per port).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath5k_config updates the software context without taking sc->lock.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes memcpy to NULL address when the ucode DMA allocation failure.
This is a fix to bug
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1861
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After reports of poor performance, a review of the latest vendor driver
(rtl8187_linux_26.1025.0328.2007) for RTL8187L devices was undertaken.
A difference was found in the code used to index the OFDM power tables. When
the Linux driver was changed, my unit works at a much greater range than
before. I think this fixes Bugzilla #12380 and has been tested by at least
two other users.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Martín Ernesto Barreyro <barreyromartin@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A nasty bug was found where an MTU change (or anything else that caused a
reset) could race with the interrupt code. The interrupt code was entered
by a shared interrupt during the MTU change.
This change prevents the interrupt code from running while the driver is in
the middle of its reset path.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/r6040.c:441: warning: unused variable 'pdev'
Signed-off-by: Manish Katiyar <mkatiyar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this fix, virtio_net makes incorrect usage of scatterlists. It sets
the end of the scatterlist chain after the first element, despite the fact
that more entries come after it.
If you try to run dma_map_sg() on one of the scatterlists given to you by
add_buf(), you will get a null pointer oops.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 77ecaf2d5a ("gianfar: Fix VLAN
HW feature related frame/buffer size calculation") wrongly removed
priv->vlgrp assignment, and now priv->vlgrp is always NULL.
This patch fixes the issue, plus fixes following sparse warning
introduced by the same commit:
gianfar.c:1406:13: warning: context imbalance in 'gfar_vlan_rx_register' - wrong count at exit
gfar_vlan_rx_register() checks for "if (old_grp == grp)" and tries
to return w/o dropping the lock.
According to net/8021q/vlan.c VLAN core issues rx_register() callback:
1. In register_vlan_dev() only on a newly created group;
2. In unregister_vlan_dev() only if the group becomes empty.
Thus the check in the gianfar driver isn't needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current tx_has_work waited until all packets sent by the driver
are marked as completed by the FW. This is too greedy and it causes
the bnx2x_poll to spin in vain. The driver should only check that all
packets FW already completed are freed - only in unload flow the
driver should make sure that transmit queue is empty
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o reduce rx ring size from 8192 to 4096.
o cut down old huge lro buffers.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o set netdev->vlan_features appropriately.
o fix tso descriptor initialization for vlan case.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a hardware errata in some revisions of the 82574 that needs
to be worked around in the driver by setting a register bit at init.
If this bit is not set A0 versions of the 82574 can generate
tx hangs.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
802.1Q expanded the maximum ethernet frame size by 4 bytes for the
VLAN tag. We're not taking this into account in virtio_net, which
means the buffers we provide to the backend in the virtqueue RX ring
aren't big enough to hold a full MTU VLAN packet. For QEMU/KVM,
this results in the backend exiting with a packet truncation error.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spin_lock functions take a pointer to the lock, not the lock itself.
This error was noticed by compiling ebsa110_defconfig for linux-rt where
the locking functions obviously are more picky about their arguments.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Roel Kluin <12o3l@tiscali.nl>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The RTL8187 and RTL8187B devices can stall unless an explicit termination
packet is sent.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ieee80211_sta structure there is u64 supp_rates[IEEE80211_NUM_BANDS]
this is filled with all support rate from assoc_resp. If we associate
with G-band AP only supp_rates of G-band will be set the other band
supp_rates will be set to 0. If the user type this command
this will cause mac80211 to set to new channel, mac80211
does not disassociate in setting new channel, so the active
band is now A-band. then in handling the new essid mac80211 will
kick in the assoc steps which involve sending disassociation frame.
in this mac80211 will WARN_ON sta->supp_rates[A_BAND] == 0.
This fixes:
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1822http://www.kerneloops.org/searchweek.php?search=rs_get_rate
Signed-off-by: mohamed abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Artur Skawina confirmed that the first generation devices needs the same
URB_ZERO_PACKET flag, in oder to finish the pending transfer properly.
The second generation has been successfully fixed by
"p54usb: fix random traffic stalls (LM87)" (43af18f06d5)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All supported SMSC PHYs implement the standard "power down" bit 11 of
BMCR, so this patch adds support using the generic genphy_{suspend,resume}
functions.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suspend/resume routines check for phydrv != NULL, but that is
wrong because "phydrv" comes from container_of(drv). If drv is NULL,
then container_of(drv) will return non-NULL result, and the checks
won't work.
The Freescale TBI PHYs are driver-less, so "drv" is NULL, and that
leads to the following oops:
Unable to handle kernel paging request for data at address 0xffffffe4
Faulting instruction address: 0xc0215554
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c0215554] mdio_bus_suspend+0x34/0x70
LR [c01cc508] suspend_device+0x258/0x2bc
Call Trace:
[cfad3da0] [cfad3db8] 0xcfad3db8 (unreliable)
[cfad3db0] [c01cc508] suspend_device+0x258/0x2bc
[cfad3dd0] [c01cc62c] dpm_suspend+0xc0/0x140
[cfad3e20] [c01cc6f4] device_suspend+0x48/0x5c
[cfad3e40] [c0068dd8] suspend_devices_and_enter+0x8c/0x148
[cfad3e60] [c00690f8] enter_state+0x100/0x118
[cfad3e80] [c00691c0] state_store+0xb0/0xe4
[cfad3ea0] [c018c938] kobj_attr_store+0x24/0x3c
[cfad3eb0] [c00ea9a8] flush_write_buffer+0x58/0x7c
[cfad3ed0] [c00eadf0] sysfs_write_file+0x58/0xa0
[cfad3ef0] [c009e810] vfs_write+0xb4/0x16c
[cfad3f10] [c009ed40] sys_write+0x4c/0x90
[cfad3f40] [c0014954] ret_from_syscall+0x0/0x38
[...]
This patch fixes the issue, plus removes unneeded parentheses
and fixes indentation level in mdio_bus_suspend().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A link change interrupt might be queued and activated after the loopback was set
and it will cause the loopback to fail. The PHY lock should be kept until the
loopback test is over.
That implies that the bnx2x_test_link should used within the loopback function
and not bnx2x_wait_for_link since that function also takes the PHY link
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Waiting for the FW to response requires a memory barrier
Signed-off-by: Michal Kalderon <michals@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rmmod might hang without this patch since the reference counter is not going
down
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call carrier off should not be called after register_netdev since after
register netdev open can be called at any time followed by an interrupt that
will set it to carrier_on and the probe will resume control and set it to off
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failures on load were not handled correctly - separate the flow to handle
different failures
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling napi disabled unconditionally at netif stop
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid complications, make sure that the HW is in reset (as it should be)
before trying to take it out of reset. In normal flows, the HW is indeed in rest
so this should have no effect
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be consistent with mac80211 drivers and return correct return code.
NETDEV_TX_OK is 0, but we need to be consistent wrt formatting amongst
implementations
re: http://marc.info/?l=linux-wireless&m=123119327419865&w=2
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Giuseppe Cala <jiveaxe@gmail.com> (The second "a" in "Cala" should be
a grave, U+00E0) reported success on zd1211-devs@lists.sourceforge.net.
The chip info is:
zd1211b chip 0df6:0036 v4810 high 00-0c-f6 AL2230_RF pa0 g--N-
The Sitecom WL-603 is detected as a zd1211b with a AL2230 RF transceiver chip.
Signed-off-by: Giuseppe Cala <jiveaxe@gmail.com>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In theory, the firmware acks the received a data frame, before signaling the driver to free it again.
However Artur Skawina <art.08.09@gmail.com> has shown that it can happen in reverse order as well.
This is very bad and could lead to memory corruptions, oopses and panics.
Thanks to Artur Skawina <art.08.09@gmail.com> for reporting and debugging this issue.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Tested-by: Artur Skawina <art.08.09@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we let the firmware do the data encryption, we have to remove the ICV and
(M)MIC at the end of the frame before we can give it back to mac80211.
Or, these data frames have a few trailing bytes on cooked monitor interfaces.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a obvious memory leak in the eeprom parser.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
KERN_INFO is too "loud" for messages that are generated by the ordinary
events, such as accociation. Use of KERN_DEBUG is consistent with
mac80211.
Suggested by Michael Gilbert <michael.s.gilbert@gmail.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mac80211 provides 2 structures to handle bitrates, namely
ieee80211_rate and ieee80211_tx_rate. To determine the short preamble
mode for an outgoing frame, the flag IEEE80211_TX_RC_USE_SHORT_PREAMBLE
must be checked on ieee80211_tx_rate and not ieee80211_rate (which rt2x00 did).
This fixes a regression which was triggered in 2.6.29-rcX as reported by Chris Clayton.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-By: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mcs7830_set_reg() and mcs7830_get_reg() are called with buffers
from stack which must not be used directly for USB transfers.
This causes corruption of the stack particulary on non x86
architectures because DMA may be used for these transfers.
Signed-off-by: Christian Eggers <christian.eggers@kathrein.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve usbnet's devdbg to always type-check diagnostic arguments,
like dev_dbg (device.h). This makes no change to the resulting size of
usbnet modules.
This patch also removes an #ifdef DEBUG directive from rndis_wlan so
it's devdbg statements are always type-checked at compile time.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
while(--j >= 0) keeps spinning when j is unsigned:
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't forget to call pci_disable_device() in myri10ge_remove()
and when myri10ge_probe() fails.
By the way, update the copyright years.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin reported a bug in two error paths where skbs were wrongly
being freed using kfree(). He provided a fix where it was replaced to
kfree_skb(), as it should be.
However, in i2400mu_rx(), the error path was missing returning an
indication of the failure. Changed to reset rx_skb to NULL and return
it to the caller, i2400mu_rxd(). It will be treated as a transient
error and just ignore the packet.
Depending on the buffering conditions inside the device, the data
packet might be dropped or the device will signal the host again for
data-ready-to-read and the host will retry.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Contrary to what the docs say, the 'extended interrupt cause' bit in
the interrupt cause register (bit 1) appears to not be maskable on at
least some of the mv643xx_eth platforms, making writing zeroes to the
interrupt mask register but not the extended interrupt mask register
insufficient to stop interrupts from occuring. Therefore, also write
zeroes to the extended interrupt mask register when shutting down the
port.
This fixes the interrupt storm seen on the Pegasos board when shutting
down the interface.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 66e63ffbc0 ("mv643xx_eth:
implement ->set_rx_mode()") cleaned up mv643xx_eth's multicast filter
programming, but broke it as well.
The non-special multicast filter table (for multicast addresses that
are not of the form 01:00:5e:00:00:xx) consists of 256 hash table
buckets organised as 64 32-bit words, where the 'accept' bits are
in the LSB of each byte, so in bits 24 16 8 0 of each 32-bit word.
The old code got this right, but the referenced commit broke this by
using bits 3 2 1 0 instead. This commit fixes this up.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit cd4ccf76bf.
On the Pegasos board, we can't do DMA burst that are longer than
one cache line. For now, go back to using 32 byte DMA bursts for
all mv643xx_eth platforms -- we can switch the ARM-based platforms
back to doing long 128 byte bursts in the next development cycle.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reported-by: Alan Curry <pacman@kosh.dhis.org>
Reported-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies how the tg3 driver handles device firmware.
The patch starts by consolidating David Woodhouse's earlier patch under
the same name. Specifically, the patch moves the request_firmware call
into a separate tg3_request_firmware() function and calls that function
from tg3_open() rather than tg3_init_one().
The patch then goes on to limit the number of devices that will make
request_firmware calls. The original firmware patch unnecessarily
requested TSO firmware for devices that did not need it. This patch
reduces the set of devices making TSO firmware patches to approximately
the following device set : 5703, 5704, and 5705.
Finally, the patch reduces the effects of a request_firmware() failure.
For those devices that are requesting TSO firmware, the driver will turn
off the TSO capability. If TSO firmware becomes available at a later
time, the device can be closed and then opened again to reacquire the
TSO capability.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_carrier_off() is sufficient to stop Tx into the driver. Stopping the Tx
queues is redundant and unnecessary. By the same token, netif_carrier_on()
will be sufficient to re-enable Tx, so waking the queues is unnecessary.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register VLAN ID 0 so that frames with VLAN ID 0 are received and get
their tag stripped when ixgbe is not in DCB mode. VLAN ID 0 means
that the frame is 'priority tagged' only - it is not a VLAN, but the
priority value is the tag in valid. The functions
ixgbe_vlan_rx_register() and ixgbe_vlan_rx_kill_vid() were moved up a
couple functions to correct compiling issues with this change.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The is an issue where setting Relaxed Ordering (RO) bit
(in a PCI-E write transaction) on 82598 causing the chipset
to drop DCA hints. This patch forces RO not to be set for
descriptors as well as payload. This will only be in effect
while DCA is enabled and no performance difference was
noticed in testing.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the assigned value is being overwritten shortly after, it can be
dropped and so the whole variable definition moved to the start of the
function.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is copy and paste from the original driver. As skb_reserve() is
also called within korina_alloc_ring() when initially allocating the
receive descriptors, the same should be done when allocating new space
after passing an skb to upper layers.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the last loop iteration, i has the value RC32434_NUM_RDS and
therefore leads to an index overflow when used afterwards to address the
last element. This is yet another another bug introduced when rewriting
parts of the driver for upstream preparation, as the original driver
used 'RC32434_NUM_RDS - 1' instead.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lro manager's frag_align_pad setting was missing,
leading to misaligned access to the skb passed up
to the stack.
Tested-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases when an underrun occur, all macb buffers where consumed
and the netif_queue was stopped infinitely. This happens then the TGO
(transfer ongoing) bit in the TSR is set (and UND). It seems like
clening up after the underrun makes the driver and the macb hardware
end up in an inconsistent state. The result of this is that in the
following calls to macb_tx no TX buffers are released -> the
netif_queue was stopped, and never woken up again.
The solution is to disable the transmitter, if TGO is set, before
clening up after the underrun, and re-enable the transmitter when the
cleaning up is done.
Signed-off-by: Richard Röjfors <richard.rojfors@endian.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updating the version and the year of updated files
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make sure no swapping are made by the compiler, changed HAS_WORK to inline
functions and added all the necessary barriers
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Driver supports the 57711 and 57711E as well but the description was out of
date
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the default PHY version (0x4321) is read - the PHY FW load failed
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10M/100M autoneg was not establishing link.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting loopback requires time to take effect
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HW should be configured so fast toggling between 1G and 10G will not be
missed. Make sure that the HW is re-configured in full
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the page size is > 8KB this violation happens
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't dump eeprom when bnx2x adapter is down. Running ethtool -e causes an eeh
without it when the device is down
Signed-off-by: Paul Larson <pl@linux.vnet.ibm.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Has a negative side effect when sending MAC update with no content (as done in
the self-test)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lock was release too soon. Make sure the HW is marked as locked until the
boot driver was unloaded from FW perspective
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failures in the probe not handled correctly - separate the flow to handle
different failures
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error check could result with not freeing the IRQ
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Use consistent types for ehca_plpar_hcall9()
IB/ehca: Fix printk format warnings from u64 type change
IPoIB: Do not print error messages for multicast join retries
IB/mlx4: Fix memory ordering problem when posting LSO sends
mlx4_core: Fix min() warning
IPoIB: Fix deadlock between ipoib_open() and child interface create
IPoIB: Fix hang in napi_disable() if P_Key is never found
p54 doesn't support AES-128-CMAC offload.
This patch will fix the noisy mac80211 warnings, when 802.11w is enabled:
mac80211-phy189: failed to set key (4, ff:ff:ff:ff:ff:ff) to hardware (-22)
mac80211-phy189: failed to set key (5, ff:ff:ff:ff:ff:ff) to hardware (-22)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When running modprobe rt73usb, and then rmmod rt73usb, and then
iwconfig, the wlan0 device does not disappear. When repeating this
process again, we get a kernel Oops errors and "BUG: unable to handle
kernel paging request..." message in the kernel log.
The reason for this is that there is an error in rt2x00rfkill_free(),
which is called in the process of removing the device
(rt2x00lib_remove_dev() in rt2x00dev.c).
rt2x00rfkill_free() clears the RFKILL_STATE_ALLOCATED bit , which is
bit number 1 () in rt2x00dev->flags instead of in
rt2x00dev->rfkill_state. As a result, when checking the
DEVICE_STATE_REGISTERED_HW bit (bit number 1 in rt2x00dev->flags) in
rt2x00lib_remove_hw() it is **unset**, and we wrongly **don't** call
ieee80211_unregister_hw().
This patch corrects this: the parameter for __test_and_clear_bit() in
rt2x00rfkill_free() should be &rt2x00dev->rfkill_state and not
&rt2x00dev->flags.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In function iwl_send_cmd_sync(), if the flag CMD_WANT_SKB is set but
we are not provided with a valid SKB (cmd->meta.u.skb == NULL), we need
to remove the CMD_WANT_SKB flag from the TX cmd queue. Otherwise in case
the cmd comes in later, it will possibly set an invalid address. Thus
it causes an invalid memory access.
This fixed the bug http://bugzilla.kernel.org/show_bug.cgi?id=11326.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect operator causes the REG_DOMAIN_2GHZ_MASK to be zero which
surely was not the goal of this definition. Mask out the 11a flags
correctly.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was not supposed to be a bitwise AND operation, but a check of
two separate conditions. Anyway, the old code happened to result in
the same behavior, so this is just changing the code to be easier to
understand and also to keep sparse from warning about dubious
operators.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Data structures that come over the wire from the WLAN firmware must be packed.
This fixes alignment problems on the blackfin architecture and, reportedly, on
the AVR32.
This is a replacement for the previous version of this patch which had also
explicitly used get_unaligned_ macros. As Johannes Berg pointed out, these
macros were unnecessary.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Colin McCabe <colin@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug that could occur, if it the eeprom is incomplete or partly corrupted.
BUG: unable to handle kernel NULL pointer dereference at 00000008
IP: p54_assign_address+0x108/0x15d [p54common]
Oops: 0002 [#1] SMP
Pid: 12988, comm: phy1 Tainted: P W 2.6.28-rc6-wl #3
RIP: 0010: p54_assign_address+0x108/0x15d [p54common]
[...]
Call Trace:
p54_alloc_skb+0xa3/0xc0 [p54common]
p54_scan+0x37/0x204 [p54common]
[...]
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes a build error in absence of CONFIG_IPV6:
drivers/net/netxen/netxen_nic_main.c:1189: error: implicit declaration of function 'ipv6_hdr'
drivers/net/netxen/netxen_nic_main.c:1189: error: invalid type argument of '->'
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For NX3031 only one I/O range is mapped, so unmapping other
two which are used by older chips, causes this warning on
ppc64.
"Attempt to iounmap early bolted mapping at 0x0000000000000000"
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix
drivers/net/mlx4/profile.c: In function `mlx4_make_profile':
drivers/net/mlx4/profile.c:110: warning: comparison of distinct pointer types lacks a cast
This happened because num_possible_cpus() was secretly changed by
commit ae7a47e7 ("cpumask: make cpumask.h eat its own dogfood.") from
returning "int" to (now) returning "unsigned int". I think that was a
good change, so we should just swallow the fallout.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Cc: Jack Morgenstein <jackm@dev.mellanox.co.il>
Cc: Vladimir Sokolovsky <vlad@mellanox.co.il>
Cc: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (95 commits)
b44: GFP_DMA skb should not escape from driver
korina: do not use IRQF_SHARED with IRQF_DISABLED
korina: do not stop queue here
korina: fix handling tx_chain_tail
korina: do tx at the right position
korina: do schedule napi after testing for it
korina: rework korina_rx() for use with napi
korina: disable napi on close and restart
korina: reset resource buffer size to 1536
korina: fix usage of driver_data
bnx2x: First slow path interrupt race
bnx2x: MTU Filter
bnx2x: Indirection table initialization index
bnx2x: Missing brackets
bnx2x: Fixing the doorbell size
bnx2x: Endianness issues
bnx2x: VLAN tagged packets without VLAN offload
bnx2x: Protecting the link change indication
bnx2x: Flow control updated before reporting the link
bnx2x: Missing mask when calculating flow control
...
b44 chip has some hardware limitations, that need GFP_DMA bounce
buffers in some situations.
In order to not deplete DMA zone, we should keep allocated GFP_DMA skb
only for driver use. At rx time, we copy such skb to newly allocated
skb, reusing existing copybreak infrastructure.
On machines with low amount of memory, all skb meet the hardware limitation,
so no copy is needed. We detect this situation using a new device flag, set
to one if one GFP_DMA skb was ever allocated by b44_alloc_rx_skb().
Previously allocated skb, even outside from DMA zone will then be recycled,
to have minimal impact on DMA zone use.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Tested-by: Ionut Leonte <ionut.leonte@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
