The Geneve encapsulation, as defined in RFC 8926, has a Protocol Type
field, which states the Ethertype of the payload appearing after the
Geneve header.
Commit 435fe1c0c1 ("net: geneve: support IPv4/IPv6 as inner protocol")
introduced a new IFLA_GENEVE_INNER_PROTO_INHERIT flag that allowed the
use of other Ethertypes than Ethernet. However, it did not get rid of a
restriction that prohibits receiving payloads other than Ethernet,
instead the commit white-listed additional Ethertypes, IPv4 and IPv6.
This patch removes this restriction, making it possible to receive any
Ethertype as a payload, if the IFLA_GENEVE_INNER_PROTO_INHERIT flag is
set.
The restriction was set in place back in commit 0b5e8b8eea
("net: Add Geneve tunneling protocol driver"), which implemented a
protocol layer driver for Geneve to be used with Open vSwitch. The
relevant discussion about introducing the Ethertype white-list can be
found here:
https://lore.kernel.org/netdev/CAEP_g=_1q3ACX5NTHxLDnysL+dTMUVzdLpgw1apLKEdDSWPztw@mail.gmail.com/
<quote>
>> + if (unlikely(geneveh->proto_type != htons(ETH_P_TEB)))
>
> Why? I thought the point of geneve carrying protocol field was to
> allow protocols other than Ethernet... is this temporary maybe?
Yes, it is temporary. Currently OVS only handles Ethernet packets but
this restriction can be lifted once we have a consumer that is capable
of handling other protocols.
</quote>
This white-list was then ported to a generic Geneve netdevice in commit
371bd1061d ("geneve: Consolidate Geneve functionality in single
module."). Preserving the Ethertype white-list at this point made sense,
as the Geneve device could send out only Ethernet payloads anyways.
However, now that the Geneve netdevice supports encapsulating other
payloads with IFLA_GENEVE_INNER_PROTO_INHERIT and we have a consumer
capable of other protocols, it seems appropriate to lift the restriction
and allow any Geneve payload to be received.
Signed-off-by: Josef Miegl <josef@miegl.cz>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Eyal Birger <eyal.birger@gmail.com>
Link: https://lore.kernel.org/r/20230319220954.21834-1-josef@miegl.cz
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The GENEVE tunnel used with IFLA_GENEVE_INNER_PROTO_INHERIT is
point-to-point, so set IFF_POINTOPOINT to reflect that.
Signed-off-by: Josef Miegl <josef@miegl.cz>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch pass netlink message header and portid to rtnl_configure_link()
All the functions in this call chain need to add the parameters so we can
use them in the last call rtnl_notify(), and notify the userspace about
the new link info if NLM_F_ECHO flag is set.
- rtnl_configure_link()
- __dev_notify_flags()
- rtmsg_ifinfo()
- rtmsg_ifinfo_event()
- rtmsg_ifinfo_build_skb()
- rtmsg_ifinfo_send()
- rtnl_notify()
Also move __dev_notify_flags() declaration to net/core/dev.h, as Jakub
suggested.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce a simple helper function to replace a common pattern.
When accessing the GRO header, we fetch the pointer from frag0,
then test its validity and fetch it from the skb when necessary.
This leads to the pattern
skb_gro_header_fast -> skb_gro_header_hard -> skb_gro_header_slow
recurring many times throughout GRO code.
This patch replaces these patterns with a single inlined function
call, improving code readability.
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220823071034.GA56142@debian
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
According to Guillaume Nault RT_TOS should never be used for IPv6.
Quote:
RT_TOS() is an old macro used to interprete IPv4 TOS as described in
the obsolete RFC 1349. It's conceptually wrong to use it even in IPv4
code, although, given the current state of the code, most of the
existing calls have no consequence.
But using RT_TOS() in IPv6 code is always a bug: IPv6 never had a "TOS"
field to be interpreted the RFC 1349 way. There's no historical
compatibility to worry about.
Fixes: 3a56f86f1b ("geneve: handle ipv6 priority like ipv4 tos")
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Matthias May <matthias.may@westermo.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current code retrieves the TOS field after the lookup
on the ipv4 routing table. The routing process currently
only allows routing based on the original 3 TOS bits, and
not on the full 6 DSCP bits.
As a result the retrieved TOS is cut to the 3 bits.
However for inheriting purposes the full 6 bits should be used.
Extract the full 6 bits before the route lookup and use
that instead of the cut off 3 TOS bits.
Fixes: e305ac6cf5 ("geneve: Add support to collect tunnel metadata.")
Signed-off-by: Matthias May <matthias.may@westermo.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Link: https://lore.kernel.org/r/20220805190006.8078-1-matthias.may@westermo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new ip_tunnel_key field with the flow flags in the IPv4 route
lookups for the encapsulated packet. This will be used by the
bpf_skb_set_tunnel_key helper in the subsequent commit.
Signed-off-by: Paul Chaignon <paul@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/fcc2e0eea01e8ea465a180126366ec20596ba530.1658759380.git.paul@isovalent.com
In the most common setups, the geneve tunnels use an inner
ethernet encapsulation. In the GRO path, when such condition is
true, we can call directly the relevant GRO helper and avoid
a few indirect calls.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing netlink attribute policy and size calculation.
Also enable strict validation from this new attribute onwards.
Fixes: 435fe1c0c1 ("net: geneve: support IPv4/IPv6 as inner protocol")
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Link: https://lore.kernel.org/r/20220322043954.3042468-1-eyal.birger@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds support for encapsulating IPv4/IPv6 within GENEVE.
In order to use this, a new IFLA_GENEVE_INNER_PROTO_INHERIT flag needs
to be provided at device creation. This property cannot be changed for
the time being.
In case IP traffic is received on a non-tun device the drop count is
increased.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Link: https://lore.kernel.org/r/20220316061557.431872-1-eyal.birger@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Dave suggested a while ago (eleven years by now) "Let's make netif_rx()
work in all contexts and get rid of netif_rx_ni()". Eric agreed and
pointed out that modern devices should use netif_receive_skb() to avoid
the overhead.
In the meantime someone added another variant, netif_rx_any_context(),
which behaves as suggested.
netif_rx() must be invoked with disabled bottom halves to ensure that
pending softirqs, which were raised within the function, are handled.
netif_rx_ni() can be invoked only from process context (bottom halves
must be enabled) because the function handles pending softirqs without
checking if bottom halves were disabled or not.
netif_rx_any_context() invokes on the former functions by checking
in_interrupts().
netif_rx() could be taught to handle both cases (disabled and enabled
bottom halves) by simply disabling bottom halves while invoking
netif_rx_internal(). The local_bh_enable() invocation will then invoke
pending softirqs only if the BH-disable counter drops to zero.
Eric is concerned about the overhead of BH-disable+enable especially in
regard to the loopback driver. As critical as this driver is, it will
receive a shortcut to avoid the additional overhead which is not needed.
Add a local_bh_disable() section in netif_rx() to ensure softirqs are
handled if needed.
Provide __netif_rx() which does not disable BH and has a lockdep assert
to ensure that interrupts are disabled. Use this shortcut in the
loopback driver and in drivers/net/*.c.
Make netif_rx_ni() and netif_rx_any_context() invoke netif_rx() so they
can be removed once they are no more users left.
Link: https://lkml.kernel.org/r/20100415.020246.218622820.davem@davemloft.net
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All gro_complete() handlers are called from napi_gro_complete()
while rcu_read_lock() has been called.
There is no point stacking more rcu_read_lock()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All gro_receive() handlers are called from dev_gro_receive()
while rcu_read_lock() has been called.
There is no point stacking more rcu_read_lock()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
include/linux/netdevice.h became too big, move gro stuff
into include/net/gro.h
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the header size check in geneve6_xmit_skb and geneve_xmit_skb
to use pskb_inet_may_pull rather than pskb_network_may_pull. This fixes
two kernel selftest failures introduced by the commit introducing the
checks:
IPv4 over geneve6: PMTU exceptions
IPv4 over geneve6: PMTU exceptions - nexthop objects
It does this by correctly accounting for the fact that IPv4 packets may
transit over geneve IPv6 tunnels (and vice versa), and still fixes the
uninit-value bug fixed by the original commit.
Reported-by: kernel test robot <oliver.sang@intel.com>
Fixes: 6628ddfec7 ("net: geneve: check skb is large enough for IPv4/IPv6 header")
Suggested-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Check within geneve_xmit_skb/geneve6_xmit_skb that sk_buff structure
is large enough to include IPv4 or IPv6 header, and reject if not. The
geneve_xmit_skb portion and overall idea was contributed by Eric Dumazet.
Fixes a KMSAN-found uninit-value bug reported by syzbot at:
https://syzkaller.appspot.com/bug?id=abe95dc3e3e9667fc23b8d81f29ecad95c6f106f
Suggested-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot+2e406a9ac75bb71d4b7a@syzkaller.appspotmail.com
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similar to the previous commit, let even geneve
passthrou the L4 GRO packets
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the interface is part of a bridge or an Open vSwitch port and a
packet exceed a PMTU estimate, an ICMP reply is sent to the sender. When
using the external mode (collect metadata) the source and destination
addresses are reversed, so that Open vSwitch can match the packet
against an existing (reverse) flow.
But inverting the source and destination addresses in the shared
ip_tunnel_info will make following packets of the flow to use a wrong
destination address (packets will be tunnelled to itself), if the flow
isn't updated. Which happens with Open vSwitch, until the flow times
out.
Fixes this by uncloning the skb's ip_tunnel_info before inverting its
source and destination addresses, so that the modification will only be
made for the PTMU packet, not the following ones.
Fixes: c1a800e88d ("geneve: Support for PMTU discovery on directly bridged links")
Tested-by: Eelco Chaudron <echaudro@redhat.com>
Reviewed-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some protocol HW GSO requires fraglist supported by the device, like
SCTP. Without NETIF_F_FRAGLIST set in the dev features of geneve, it
would have to do SW GSO before the packets enter the driver, even
when the geneve dev and lower dev (like veth) both have the feature
of NETIF_F_GSO_SCTP.
So this patch is to add it for geneve.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
udp_tunnel_nic handles REGISTER and UNREGISTER event, now that all
drivers use that infra we can drop the event handling in the tunnel
drivers.
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
linux/netdevice.h is included in very many places, touching any
of its dependecies causes large incremental builds.
Drop the linux/ethtool.h include, linux/netdevice.h just needs
a forward declaration of struct ethtool_ops.
Fix all the places which made use of this implicit include.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20201120225052.1427503-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace ip_tunnel_get_stats64() with the new identical core function
dev_get_tstats64().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds transport ports information for route lookup so that
IPsec can select Geneve tunnel traffic to do encryption. This is
needed for OVS/OVN IPsec with encrypted Geneve tunnels.
This can be tested by configuring a host-host VPN using an IKE
daemon and specifying port numbers. For example, for an
Openswan-type configuration, the following parameters should be
configured on both hosts and IPsec set up as-per normal:
$ cat /etc/ipsec.conf
conn in
...
left=$IP1
right=$IP2
...
leftprotoport=udp/6081
rightprotoport=udp
...
conn out
...
left=$IP1
right=$IP2
...
leftprotoport=udp
rightprotoport=udp/6081
...
The tunnel can then be setup using "ip" on both hosts (but
changing the relevant IP addresses):
$ ip link add tun type geneve id 1000 remote $IP2
$ ip addr add 192.168.0.1/24 dev tun
$ ip link set tun up
This can then be tested by pinging from $IP1:
$ ping 192.168.0.2
Without this patch the traffic is unencrypted on the wire.
Fixes: 2d07dc79fe ("geneve: add initial netdev driver for GENEVE tunnels")
Signed-off-by: Qiuyu Xiao <qiuyu.xiao.qyx@gmail.com>
Signed-off-by: Mark Gray <mark.d.gray@redhat.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the interface is a bridge or Open vSwitch port, and we can't
forward a packet because it exceeds the local PMTU estimate,
trigger an ICMP or ICMPv6 reply to the sender, using the same
interface to forward it back.
If metadata collection is enabled, set destination and source
addresses for the flow as if we were receiving the packet, so that
Open vSwitch can match the ICMP error against the existing
association.
v2: Use netif_is_any_bridge_port() (David Ahern)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's currently possible to bridge Ethernet tunnels carrying IP
packets directly to external interfaces without assigning them
addresses and routes on the bridged network itself: this is the case
for UDP tunnels bridged with a standard bridge or by Open vSwitch.
PMTU discovery is currently broken with those configurations, because
the encapsulation effectively decreases the MTU of the link, and
while we are able to account for this using PMTU discovery on the
lower layer, we don't have a way to relay ICMP or ICMPv6 messages
needed by the sender, because we don't have valid routes to it.
On the other hand, as a tunnel endpoint, we can't fragment packets
as a general approach: this is for instance clearly forbidden for
VXLAN by RFC 7348, section 4.3:
VTEPs MUST NOT fragment VXLAN packets. Intermediate routers may
fragment encapsulated VXLAN packets due to the larger frame size.
The destination VTEP MAY silently discard such VXLAN fragments.
The same paragraph recommends that the MTU over the physical network
accomodates for encapsulations, but this isn't a practical option for
complex topologies, especially for typical Open vSwitch use cases.
Further, it states that:
Other techniques like Path MTU discovery (see [RFC1191] and
[RFC1981]) MAY be used to address this requirement as well.
Now, PMTU discovery already works for routed interfaces, we get
route exceptions created by the encapsulation device as they receive
ICMP Fragmentation Needed and ICMPv6 Packet Too Big messages, and
we already rebuild those messages with the appropriate MTU and route
them back to the sender.
Add the missing bits for bridged cases:
- checks in skb_tunnel_check_pmtu() to understand if it's appropriate
to trigger a reply according to RFC 1122 section 3.2.2 for ICMP and
RFC 4443 section 2.4 for ICMPv6. This function is already called by
UDP tunnels
- a new function generating those ICMP or ICMPv6 replies. We can't
reuse icmp_send() and icmp6_send() as we don't see the sender as a
valid destination. This doesn't need to be generic, as we don't
cover any other type of ICMP errors given that we only provide an
encapsulation function to the sender
While at it, make the MTU check in skb_tunnel_check_pmtu() accurate:
we might receive GSO buffers here, and the passed headroom already
includes the inner MAC length, so we don't have to account for it
a second time (that would imply three MAC headers on the wire, but
there are just two).
This issue became visible while bridging IPv6 packets with 4500 bytes
of payload over GENEVE using IPv4 with a PMTU of 4000. Given the 50
bytes of encapsulation headroom, we would advertise MTU as 3950, and
we would reject fragmented IPv6 datagrams of 3958 bytes size on the
wire. We're exclusively dealing with network MTU here, though, so we
could get Ethernet frames up to 3964 octets in that case.
v2:
- moved skb_tunnel_check_pmtu() to ip_tunnel_core.c (David Ahern)
- split IPv4/IPv6 functions (David Ahern)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
geneve_nl2info() sets 'df' conditionally, so we have to
initialize it by copying the value from existing geneve
device in geneve_changelink().
Fixes: 56c09de347 ("geneve: allow changing DF behavior after creation")
Reported-by: syzbot+7ebc2e088af5e4c0c9fa@syzkaller.appspotmail.com
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cater to devices which:
(a) may want to sleep in the callbacks;
(b) only have IPv4 support;
(c) need all the programming to happen while the netdev is up.
Drivers attach UDP tunnel offload info struct to their netdevs,
where they declare how many UDP ports of various tunnel types
they support. Core takes care of tracking which ports to offload.
Use a fixed-size array since this matches what almost all drivers
do, and avoids a complexity and uncertainty around memory allocations
in an atomic context.
Make sure that tunnel drivers don't try to replay the ports when
new NIC netdev is registered. Automatic replays would mess up
reference counting, and will be removed completely once all drivers
are converted.
v4:
- use a #define NULL to avoid build issues with CONFIG_INET=n.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new structure geneve_config and moves the per-device
configuration attributes to it, like we already have in VXLAN with
struct vxlan_config. This ends up being pretty invasive since those
attributes are used everywhere.
This allows us to clean up the argument lists for geneve_configure (4
arguments instead of 8) and geneve_nl2info (5 instead of 9).
This also reduces the copy-paste of code setting those attributes
between geneve_configure and geneve_changelink to a single memcpy,
which would have avoided the bug fixed in commit
56c09de347 ("geneve: allow changing DF behavior after creation").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, trying to change the DF parameter of a geneve device does
nothing:
# ip -d link show geneve1
14: geneve1: <snip>
link/ether <snip>
geneve id 1 remote 10.0.0.1 ttl auto df set dstport 6081 <snip>
# ip link set geneve1 type geneve id 1 df unset
# ip -d link show geneve1
14: geneve1: <snip>
link/ether <snip>
geneve id 1 remote 10.0.0.1 ttl auto df set dstport 6081 <snip>
We just need to update the value in geneve_changelink.
Fixes: a025fb5f49 ("geneve: Allow configuration of DF behaviour")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the geneve interface is in collect_md (external) mode, it can't send any
packets submitted directly to its net interface, as such packets won't have
metadata attached. This is expected.
However, the kernel itself sends some packets to the interface, most
notably, IPv6 DAD, IPv6 multicast listener reports, etc. This is not wrong,
as tunnel metadata can be specified in routing table (although technically,
that has never worked for IPv6, but hopefully will be fixed eventually) and
then the interface must correctly participate in IPv6 housekeeping.
The problem is that any such attempt increases the tx_error counter. Just
bringing up a geneve interface with IPv6 enabled is enough to see a number
of tx_errors. That causes confusion among users, prompting them to find
a network error where there is none.
Change the counter used to tx_dropped. That better conveys the meaning
(there's nothing wrong going on, just some packets are getting dropped) and
hopefully will make admins panic less.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IFLA_GENEVE_* attributes are in the data array, which is correctly
used when fetching the value, but not when setting the extended
ack. Because IFLA_GENEVE_MAX < IFLA_MAX, we avoid out of bounds
array accesses, but we don't provide a pointer to the invalid
attribute to userspace.
Fixes: a025fb5f49 ("geneve: Allow configuration of DF behaviour")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debug check must be done after unregister_netdevice_many() call --
the list_del() for this is done inside .ndo_stop.
Fixes: 2843a25348 ("geneve: speedup geneve tunnels dismantle")
Reported-and-tested-by: <syzbot+68a8ed58e3d17c700de5@syzkaller.appspotmail.com>
Cc: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
ipv6_stub uses the ip6_dst_lookup function to allow other modules to
perform IPv6 lookups. However, this function skips the XFRM layer
entirely.
All users of ipv6_stub->ip6_dst_lookup use ip_route_output_flow (via the
ip_route_output_key and ip_route_output helpers) for their IPv4 lookups,
which calls xfrm_lookup_route(). This patch fixes this inconsistent
behavior by switching the stub to ip6_dst_lookup_flow, which also calls
xfrm_lookup_route().
This requires some changes in all the callers, as these two functions
take different arguments and have different return types.
Fixes: 5f81bd2e5d ("ipv6: export a stub for IPv6 symbols used by vxlan")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
IN_MULTICAST's primary intent is as a uapi macro.
Elsewhere in the kernel we use ipv4_is_multicast consistently.
This patch unifies linux's multicast checks to use that function
rather than this macro.
Signed-off-by: Dave Taht <dave.taht@gmail.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit a07966447f ("geneve: ICMP error lookup handler") I wrongly
assumed buffers from icmp_socket_deliver() would be linear. This is not
the case: icmp_socket_deliver() only guarantees we have 8 bytes of linear
data.
Eric fixed this same issue for fou and fou6 in commits 26fc181e6c
("fou, fou6: do not assume linear skbs") and 5355ed6388 ("fou, fou6:
avoid uninit-value in gue_err() and gue6_err()").
Use pskb_may_pull() instead of checking skb->len, and take into account
the fact we later access the GENEVE header with udp_hdr(), so we also
need to sum skb_transport_header() here.
Reported-by: Guillaume Nault <gnault@redhat.com>
Fixes: a07966447f ("geneve: ICMP error lookup handler")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
