Add the compatibility string documentation for SiFive FU540-C0000
interface.
On the FU540, this driver also needs to read and write registers in a
management IP block that monitors or drives boundary signals for the
GEMGXL IP block that are not directly mapped to GEMGXL registers.
Therefore, add additional range to "reg" property for SiFive GEMGXL
management IP registers.
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Lots of bug fixes here:
1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.
2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
Crispin.
3) Use after free in psock backlog workqueue, from John Fastabend.
4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
Salem.
5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.
6) Network header needs to be set for packet redirect in nfp, from
John Hurley.
7) Fix udp zerocopy refcnt, from Willem de Bruijn.
8) Don't assume linear buffers in vxlan and geneve error handlers,
from Stefano Brivio.
9) Fix TOS matching in mlxsw, from Jiri Pirko.
10) More SCTP cookie memory leak fixes, from Neil Horman.
11) Fix VLAN filtering in rtl8366, from Linus Walluij.
12) Various TCP SACK payload size and fragmentation memory limit fixes
from Eric Dumazet.
13) Use after free in pneigh_get_next(), also from Eric Dumazet.
14) LAPB control block leak fix from Jeremy Sowden"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
lapb: fixed leak of control-blocks.
tipc: purge deferredq list for each grp member in tipc_group_delete
ax25: fix inconsistent lock state in ax25_destroy_timer
neigh: fix use-after-free read in pneigh_get_next
tcp: fix compile error if !CONFIG_SYSCTL
hv_sock: Suppress bogus "may be used uninitialized" warnings
be2net: Fix number of Rx queues used for flow hashing
net: handle 802.1P vlan 0 packets properly
tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
tcp: add tcp_min_snd_mss sysctl
tcp: tcp_fragment() should apply sane memory limits
tcp: limit payload size of sacked skbs
Revert "net: phylink: set the autoneg state in phylink_phy_change"
bpf: fix nested bpf tracepoints with per-cpu data
bpf: Fix out of bounds memory access in bpf_sk_storage
vsock/virtio: set SOCK_DONE on peer shutdown
net: dsa: rtl8366: Fix up VLAN filtering
net: phylink: set the autoneg state in phylink_phy_change
net: add high_order_alloc_disable sysctl/static key
tcp: add tcp_tx_skb_cache sysctl
...
This tag contains fixes, defconfig, and DT data changes for the v5.2-rc
series. The fixes are relatively straightforward:
- Addition of a TLB fence in the vmalloc_fault path, so the CPU doesn't
enter an infinite page fault loop;
- Readdition of the pm_power_off export, so device drivers that
reassign it can now be built as modules;
- A udelay() fix for RV32, fixing a miscomputation of the delay time;
- Removal of deprecated smp_mb__*() barriers.
The tag also adds initial DT data infrastructure for arch/riscv, along
with initial data for the SiFive FU540-C000 SoC and the corresponding
HiFive Unleashed board.
We also update the RV64 defconfig to include some core drivers for the
FU540 in the build.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEElRDoIDdEz9/svf2Kx4+xDQu9KksFAl0HtEkACgkQx4+xDQu9
KkuRIw//f2vSrUyMh44sevr6euVD0K++hQ0AbteQ94cGHqYWWaNxfwMHFD91Gxbj
wowTwgssq7H9nePsKANjiiLULnZNIkWXAlIncjzv3aXkH6JG3f9nEGR49yzvCbIZ
yN8wgElJ8rcVWLd096E53Su84CzxuJJ2o3wOI1nQi8aI4h3LwkM2b/O4GxZFpnWb
vIhWXqjvbUb8XL7Y+VPewtxnZItOUDHkuIkup4kP2bTgl2iDW93hzWwxNKbt6v+m
9wTzAChjcepCAXSmEGeeZ/h2HNqw2crs+NWOe0drcKxL2vKPZ6gS8ZRX/NuIoDr4
JgMILzYSO28z8N6w1cJJUdN4eGhCTvdxVTQXvkk/yZoT08X6M0xb5A1MbtizgOJ6
mZK/vM9gtuoUSZG0SRNeNoqHbWu1tIm29z435Be8hWAtzXlEfewJm8ntgFO4dGmb
E8TRSgjLzdHY0Nvwx/KVtvYmE/TMybVVRsxJJ525dqJlHT7f3VuRstvw7VQJQpz2
+JfsZbYk1KjbUc25QpAqF1LUxrRQFn2JL0Cqw+L49J8eshY77rsTcAKP6ZZWiSFZ
qodU0oPF4BkS1t0bnFuNwlqsAr/q9EiAnQO7+SvqQY/ZUnMNk9gCNn5k/rHMCfyD
2Dyo6iAbj+Yyb1rrQxX6QnlbHgpFxsG3N4s9E5jOPgKyEQM4JQ4=
=aotJ
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-v5.2/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"This contains fixes, defconfig, and DT data changes for the v5.2-rc
series.
The fixes are relatively straightforward:
- Addition of a TLB fence in the vmalloc_fault path, so the CPU
doesn't enter an infinite page fault loop
- Readdition of the pm_power_off export, so device drivers that
reassign it can now be built as modules
- A udelay() fix for RV32, fixing a miscomputation of the delay time
- Removal of deprecated smp_mb__*() barriers
This also adds initial DT data infrastructure for arch/riscv, along
with initial data for the SiFive FU540-C000 SoC and the corresponding
HiFive Unleashed board.
We also update the RV64 defconfig to include some core drivers for the
FU540 in the build"
* tag 'riscv-for-v5.2/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: remove unused barrier defines
riscv: mm: synchronize MMU after pte change
riscv: dts: add initial board data for the SiFive HiFive Unleashed
riscv: dts: add initial support for the SiFive FU540-C000 SoC
dt-bindings: riscv: convert cpu binding to json-schema
dt-bindings: riscv: sifive: add YAML documentation for the SiFive FU540
arch: riscv: add support for building DTB files from DT source data
riscv: Fix udelay in RV32.
riscv: export pm_power_off again
RISC-V: defconfig: enable clocks, serial console
At Rob's request, we're starting to migrate our DT binding
documentation to json-schema YAML format. Start by converting our cpu
binding documentation. While doing so, document more properties and
nodes. This includes adding binding documentation support for the E51
and U54 CPU cores ("harts") that are present on this SoC. These cores
are described in:
https://static.dev.sifive.com/FU540-C000-v1.0.pdf
This cpus.yaml file is intended to be a starting point and to
evolve over time. It passes dt-doc-validate as of the yaml-bindings
commit 4c79d42e9216.
This patch was originally based on the ARM json-schema binding
documentation as added by commit 672951cbd1 ("dt-bindings: arm: Convert
cpu binding to json-schema").
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Add YAML DT binding documentation for the SiFive FU540 SoC. This
SoC is documented at:
https://static.dev.sifive.com/FU540-C000-v1.0.pdf
Passes dt-doc-validate, as of yaml-bindings commit 4c79d42e9216.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Some TCP peers announce a very small MSS option in their SYN and/or
SYN/ACK messages.
This forces the stack to send packets with a very high network/cpu
overhead.
Linux has enforced a minimal value of 48. Since this value includes
the size of TCP options, and that the options can consume up to 40
bytes, this means that each segment can include only 8 bytes of payload.
In some cases, it can be useful to increase the minimal value
to a saner value.
We still let the default to 48 (TCP_MIN_SND_MSS), for compatibility
reasons.
Note that TCP_MAXSEG socket option enforces a minimal value
of (TCP_MIN_MSS). David Miller increased this minimal value
in commit c39508d6f1 ("tcp: Make TCP_MAXSEG minimum more correct.")
from 64 to 88.
We might in the future merge TCP_MIN_SND_MSS and TCP_MIN_MSS.
CVE-2019-11479 -- tcp mss hardcoded to 48
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Tyler Hicks <tyhicks@canonical.com>
Cc: Bruce Curtis <brucec@netflix.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull cgroup fixes from Tejun Heo:
"This has an unusually high density of tricky fixes:
- task_get_css() could deadlock when it races against a dying cgroup.
- cgroup.procs didn't list thread group leaders with live threads.
This could mislead readers to think that a cgroup is empty when
it's not. Fixed by making PROCS iterator include dead tasks. I made
a couple mistakes making this change and this pull request contains
a couple follow-up patches.
- When cpusets run out of online cpus, it updates cpusmasks of member
tasks in bizarre ways. Joel improved the behavior significantly"
* 'for-5.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cpuset: restore sanity to cpuset_cpus_allowed_fallback()
cgroup: Fix css_task_iter_advance_css_set() cset skip condition
cgroup: css_task_iter_skip()'d iterators must be advanced before accessed
cgroup: Include dying leaders with live threads in PROCS iterations
cgroup: Implement css_task_iter_skip()
cgroup: Call cgroup_release() before __exit_signal()
docs cgroups: add another example size for hugetlb
cgroup: Use css_tryget() instead of css_tryget_online() in task_get_css()
Instead of relying on rps_needed, it is safer to use a separate
static key, since we do not want to enable TCP rx_skb_cache
by default. This feature can cause huge increase of memory
usage on hosts with millions of sockets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mlx5 devlink health fw reporters and sw reset support
This series provides mlx5 firmware reset support and firmware devlink health
reporters.
1) Add initial mlx5 kernel documentation and include devlink health reporters
2) Add CR-Space access and FW Crdump snapshot support via devlink region_snapshot
3) Issue software reset upon FW asserts
4) Add fw and fw_fatal devlink heath reporters to follow fw errors indication by
dump and recover procedures and enable trigger these functionality by user.
4.1) fw reporter:
The fw reporter implements diagnose and dump callbacks.
It follows symptoms of fw error such as fw syndrome by triggering
fw core dump and storing it and any other fw trace into the dump buffer.
The fw reporter diagnose command can be triggered any time by the user to check
current fw status.
4.2) fw_fatal repoter:
The fw_fatal reporter implements dump and recover callbacks.
It follows fatal errors indications by CR-space dump and recover flow.
The CR-space dump uses vsc interface which is valid even if the FW command
interface is not functional, which is the case in most FW fatal errors. The
CR-space dump is stored as a memory region snapshot to ease read by address.
The recover function runs recover flow which reloads the driver and triggers fw
reset if needed.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl0CsLgACgkQSD+KveBX
+j7mFwf+MYvIbUO4mXyoZIezci1UCzt1vNAkUYPceE94O9fK68ItrwtwrstgIqqS
58Tgx//MXxPpe9k9NIWjeS3i8sjcb8fDoqkjOCj7KAchv0IhSUvYFRpBrUK+yTOW
NIIXZzuCgIoR9a/hVlT/lhG+dm4MX2L5dWFtORLxMoO+ff3yiy4nNf9+Zdt0H7LT
YCELWnKeIQCvdzJAxX7OyTh3eOfc/h7o1nOsU4VugBHxKxx4T+9A26d+cZeZH5Ox
3ikTCc01ivVHqcLydAy96HQu0MENSNYNpmyDxWum3oJGFFu6hBQTM2ueRmVWZfwH
DRu+hhxONZROxxtpmP/ULmwYcLnBHg==
=VhXt
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2019-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-06-13
Mlx5 devlink health fw reporters and sw reset support
This series provides mlx5 firmware reset support and firmware devlink health
reporters.
1) Add initial mlx5 kernel documentation and include devlink health reporters
2) Add CR-Space access and FW Crdump snapshot support via devlink region_snapshot
3) Issue software reset upon FW asserts
4) Add fw and fw_fatal devlink heath reporters to follow fw errors indication by
dump and recover procedures and enable trigger these functionality by user.
4.1) fw reporter:
The fw reporter implements diagnose and dump callbacks.
It follows symptoms of fw error such as fw syndrome by triggering
fw core dump and storing it and any other fw trace into the dump buffer.
The fw reporter diagnose command can be triggered any time by the user to check
current fw status.
4.2) fw_fatal repoter:
The fw_fatal reporter implements dump and recover callbacks.
It follows fatal errors indications by CR-space dump and recover flow.
The CR-space dump uses vsc interface which is valid even if the FW command
interface is not functional, which is the case in most FW fatal errors. The
CR-space dump is stored as a memory region snapshot to ease read by address.
The recover function runs recover flow which reloads the driver and triggers fw
reset if needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Multipath hash policy value of 0 isn't distributing since the outer IP
dest and src aren't varied eventhough the inner ones are. Since the flow
is on the inner ones in the case of tunneled traffic, hashing on them is
desired.
This is done mainly for IP over GRE, hence only tested for that. But
anything else supported by flow dissection should work.
v2: Use skb_flow_dissect_flow_keys() directly so that other tunneling
can be supported through flow dissection (per Nikolay Aleksandrov).
v3: Remove accidental inclusion of ports in the hash keys and clarify
the documentation (Nikolay Alexandrov).
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9477 series chips have a SYNCLKO pin which by default outputs a
25MHz clock, but some board setups require a 125MHz clock instead. Added
a microchip,synclko-125 device tree property to allow indicating a
125MHz clock output is required.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Permit mux_id values up to 254 to be used in qmimux_register_device()
for compatibility with ip(8) and the rmnet driver.
Fixes: c6adf77953 ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=6C8e
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190614' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Remove references to old schedulers for the scheduler switching and
blkio controller documentation (Andreas)
- Kill duplicate check for report zone for null_blk (Chaitanya)
- Two bcache fixes (Coly)
- Ensure that mq-deadline is selected if zoned block device is enabled,
as we need that to support them (Damien)
- Fix io_uring memory leak (Eric)
- ps3vram fallout from LBDAF removal (Geert)
- Redundant blk-mq debugfs debugfs_create return check cleanup (Greg)
- Extend NOPLM quirk for ST1000LM024 drives (Hans)
- Remove error path warning that can now trigger after the queue
removal/addition fixes (Ming)
* tag 'for-linus-20190614' of git://git.kernel.dk/linux-block:
block/ps3vram: Use %llu to format sector_t after LBDAF removal
libata: Extend quirks for the ST1000LM024 drives with NOLPM quirk
bcache: only set BCACHE_DEV_WB_RUNNING when cached device attached
bcache: fix stack corruption by PRECEDING_KEY()
blk-mq: remove WARN_ON(!q->elevator) from blk_mq_sched_free_requests
blkio-controller.txt: Remove references to CFQ
block/switching-sched.txt: Update to blk-mq schedulers
null_blk: remove duplicate check for report zone
blk-mq: no need to check return value of debugfs_create functions
io_uring: fix memory leak of UNIX domain socket inode
block: force select mq-deadline for zoned block devices
* HE (802.11ax) work continues
* WPA3 offloads
* work on extended key ID handling continues
* fixes to honour AP supported rates with auth/assoc frames
* nl80211 netlink policy improvements to fix some issues
with strict validation on new commands with old attrs
-----BEGIN PGP SIGNATURE-----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=j+Um
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-06-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Many changes all over:
* HE (802.11ax) work continues
* WPA3 offloads
* work on extended key ID handling continues
* fixes to honour AP supported rates with auth/assoc frames
* nl80211 netlink policy improvements to fix some issues
with strict validation on new commands with old attrs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix broken SVE ptrace API when running in a big-endian configuration
- Fix performance regression due to off-by-one in TLBI range checking
- Fix build regression when using Clang
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl0DsZ0ACgkQt6xw3ITB
YzRE3wf9GJibmSnm9q5gmtHcKMrH+atXrI93nyzhBZxYaAYAKSiz7RCMSpc7iudI
bGMruaaqn/2xrdOie3vOOfSqFfzrfcFOuh/0id9R2IyiFSg08BrI369buejNRtm+
BUhdUQCe5p5afJ7PYFa7CYD+tSC1WiHXfOhH6sRYllerwaMiR9y/eqf3Gh5zB26Q
ca/+2Jh59DxXIpSWP9nTzPyV9xKOJ1B8JdMR5BMIUnOgUXQhMwNeuivRrZnEG9yT
PZDGbk5WxKci+LHPOt7stFFuo7hZn3SCKJ0mZ20VUs0w7ETMJuI0Ss4TlE2mgYag
TASmsypuLdRz5mxIeyY5QYXppSyYiA==
=AhWz
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here are some arm64 fixes for -rc5.
The only non-trivial change (in terms of the diffstat) is fixing our
SVE ptrace API for big-endian machines, but the majority of this is
actually the addition of much-needed comments and updates to the
documentation to try to avoid this mess biting us again in future.
There are still a couple of small things on the horizon, but nothing
major at this point.
Summary:
- Fix broken SVE ptrace API when running in a big-endian configuration
- Fix performance regression due to off-by-one in TLBI range checking
- Fix build regression when using Clang"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/sve: Fix missing SVE/FPSIMD endianness conversions
arm64: tlbflush: Ensure start/end of address range are aligned to stride
arm64: Don't unconditionally add -Wno-psabi to KBUILD_CFLAGS
There's no rate control algorithm that *doesn't* want to call
it internally, and calling it internally will let us modify
its behaviour in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The in-memory representation of SVE and FPSIMD registers is
different: the FPSIMD V-registers are stored as single 128-bit
host-endian values, whereas SVE registers are stored in an
endianness-invariant byte order.
This means that the two representations differ when running on a
big-endian host. But we blindly copy data from one representation
to another when converting between the two, resulting in the
register contents being unintentionally byteswapped in certain
situations. Currently this can be triggered by the first SVE
instruction after a syscall, for example (though the potential
trigger points may vary in future).
So, fix the conversion functions fpsimd_to_sve(), sve_to_fpsimd()
and sve_sync_from_fpsimd_zeropad() to swab where appropriate.
There is no common swahl128() or swab128() that we could use here.
Maybe it would be worth making this generic, but for now add a
simple local hack.
Since the byte order differences are exposed in ABI, also clarify
the documentation.
Cc: Alex Bennée <alex.bennee@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Alan Hayward <alan.hayward@arm.com>
Cc: Julien Grall <julien.grall@arm.com>
Fixes: bc0ee47603 ("arm64/sve: Core task context handling")
Fixes: 8cd969d28f ("arm64/sve: Signal handling support")
Fixes: 43d4da2c45 ("arm64/sve: ptrace and ELF coredump support")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
[will: Fix typos in comments and docs spotted by Julien]
Signed-off-by: Will Deacon <will.deacon@arm.com>
CFQ is gone. No need anymore to document its "proportional weight time
based division of disk policy".
Signed-off-by: Andreas Herrmann <aherrmann@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove references to CFQ and legacy block layer which are gone.
Update example with what's available under blk-mq.
Signed-off-by: Andreas Herrmann <aherrmann@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch fixes a spelling typo in rds.txt
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add bindings for Wiznet's w5x00 series of SPI interfaced Ethernet chips.
Based on the bindings for microchip,enc28j60.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
TLS offload drivers keep track of TCP seq numbers to make sure
the packets are fed into the HW in order.
When packets get dropped on the way through the stack, the driver
will get out of sync and have to use fallback encryption, but unless
TCP seq number is resynced it will never match the packets correctly
(or even worse - use incorrect record sequence number after TCP seq
wraps).
Existing drivers (mlx5) feed the entire record on every out-of-order
event, allowing FW/HW to always be in sync.
This patch adds an alternative, more akin to the RX resync. When
driver sees a frame which is past its expected sequence number the
stream must have gotten out of order (if the sequence number is
smaller than expected its likely a retransmission which doesn't
require resync). Driver will ask the stack to perform TX sync
before it submits the next full record, and fall back to software
crypto until stack has performed the sync.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TLS offload device may lose sync with the TCP stream if packets
arrive out of order. Drivers can currently request a resync at
a specific TCP sequence number. When a record is found starting
at that sequence number kernel will inform the device of the
corresponding record number.
This requires the device to constantly scan the stream for a
known pattern (constant bytes of the header) after sync is lost.
This patch adds an alternative approach which is entirely under
the control of the kernel. Kernel tracks records it had to fully
decrypt, even though TLS socket is in TLS_HW mode. If multiple
records did not have any decrypted parts - it's a pretty strong
indication that the device is out of sync.
We choose the min number of fully encrypted records to be 2,
which should hopefully be more than will get retransmitted at
a time.
After kernel decides the device is out of sync it schedules a
resync request. If the TCP socket is empty the resync gets
performed immediately. If socket is not empty we leave the
record parser to resync when next record comes.
Before resync in message parser we peek at the TCP socket and
don't attempt the sync if the socket already has some of the
next record queued.
On resync failure (encrypted data continues to flow in) we
retry with exponential backoff, up to once every 128 records
(with a 16k record thats at most once every 2M of data).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEmvEkXzgOfc881GuFWsYho5HknSAFAlz60fwTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRBaxiGjkeSdILI8B/41j6UxwMSYMetM/Vw2AyqPt0z671Gu
mAVzDK3PZF5WIzD5JsDlUhwN1dqvfvAZeSS1tQwQ18ZpQLkRSxlAKhkLLlxBVKpJ
0uDwYuFWwXF8DbdlRwZq+Db0GGAXW5+8WtA4gp9GTiIP6kTgmqnnaZvWPnQzQmKJ
RCY8YAzF52jXa4hBfLsXiG7NoO6cZHQJMFKLsQEpHV+GMqTcAYJHzBP6YVVXC8PG
495TREmTq5lvRKc2U3QS6//yPWleFYr5ViW/psEcBPCGdruyJI8LjDRaqnGWRBJX
vPyEVSFHtQZu49Vue3g4jbjhVr8OWTV/MsFgE/zK5Ahe+2G5969pID3n
=iCgZ
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.2-20190607' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2019-06-07
this is a pull reqeust of 9 patches for net/master.
The first patch is by Alexander Dahl and removes a duplicate menu entry from
the Kconfig. The next patch by Joakim Zhang fixes the timeout in the flexcan
driver when setting small bit rates. Anssi Hannula's patch for the xilinx_can
driver fixes the bittiming_const for CAN FD core. The two patches by Sean
Nyekjaer bring mcp25625 to the existing mcp251x driver. The patch by Eugen
Hristev implements an errata for the m_can driver. YueHaibing's patch fixes the
error handling ing can_init(). The patch by Fabio Estevam for the flexcan
driver removes an unneeded registration message during flexcan_probe(). And the
last patch is by Willem de Bruijn and adds the missing purging the socket
error queue on sock destruct.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Keystone 2 66AK2HK/E/L 1G Ethernet Switch Subsystems contains The
Common Platform Time Sync (CPTS) module which is in general compatible with
CPTS module found on "legacy" TI AM3/4/5 SoCs. So, the basic support for
Keystone 2 CPTS is available by default, but not documented.
The Keystone 2 CPTS module supports also some additional features like time
sync reference (RFTCLK) clock selection through CPTS_RFTCLK_SEL register
(offset: x08) in CPTS module, which is modelled as multiplexer clock.
This patch adds missed binding documentation for Keystone 2 66AK2HK/E/L
CPTS module.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2019-06-07
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix several bugs in riscv64 JIT code emission which forgot to clear high
32-bits for alu32 ops, from Björn and Luke with selftests covering all
relevant BPF alu ops from Björn and Jiong.
2) Two fixes for UDP BPF reuseport that avoid calling the program in case of
__udp6_lib_err and UDP GRO which broke reuseport_select_sock() assumption
that skb->data is pointing to transport header, from Martin.
3) Two fixes for BPF sockmap: a use-after-free from sleep in psock's backlog
workqueue, and a missing restore of sk_write_space when psock gets dropped,
from Jakub and John.
4) Fix unconnected UDP sendmsg hook API which is insufficient as-is since it
breaks standard applications like DNS if reverse NAT is not performed upon
receive, from Daniel.
5) Fix an out-of-bounds read in __bpf_skc_lookup which in case of AF_INET6
fails to verify that the length of the tuple is long enough, from Lorenz.
6) Fix libbpf's libbpf__probe_raw_btf to return an fd instead of 0/1 (for
{un,}successful probe) as that is expected to be propagated as an fd to
load_sk_storage_btf() and thus closing the wrong descriptor otherwise,
from Michal.
7) Fix bpftool's JSON output for the case when a lookup fails, from Krzesimir.
8) Minor misc fixes in docs, samples and selftests, from various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fully compatible with mcp2515, the mcp25625 have integrated transceiver.
This patch add the mcp25625 to the device tree bindings documentation.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
The axienet driver requires the use of an axistream-connected attribute,
but this isn't documented in the devicetree bindings. Document how this
attribute is supposed to be used, including the upcoming change to make
the usage of this attribute optional.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio child node for the MDIO bus is generally required when using
this driver but was not documented other than being shown in the
example. Document it as an optional (but usually required) parameter.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously this driver only handled interrupts from the DMA RX and TX
blocks, not from the Ethernet core itself. Add optional support for
the Ethernet core interrupt, which is used to detect rx_missed and
framing errors signalled by the hardware. In order to use this
interrupt, a third interrupt needs to be specified in the device tree.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was previously always calculating the MDIO clock divisor
(from AXI bus clock to MDIO bus clock) based on the CPU clock frequency,
assuming that it is the same as the AXI bus frequency, but that
simplistic method only works on the MicroBlaze platform.
Add support for specifying the clock used for the device in the device
tree using the clock framework. If the clock is specified then it will
be used when calculating the clock divisor. The previous CPU clock
detection method is left for backward compatibility if no clock is
specified.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the "altr,socfpga-stmmac-a10-s10" binding for Arria10/Agilex/Stratix10
implementation of the stmmac ethernet controller.
On the Arria10, Agilex, and Stratix10 SoCs, there are a few differences from
the Cyclone5 and Arria5:
- The emac PHY setup bits are in separate registers.
- The PTP reference clock select mask is different.
- The register to enable the emac signal from FPGA is different.
Because of these differences, the dwmac-socfpga glue logic driver will
use this new binding to set the appropriate bits for PHY, PTP reference
clock, and signal from FPGA.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSQHSd0lITzzeNWNm3h3BK/laaZPAUCXPkV+wAKCRDh3BK/laaZ
PMGyAQDq6ry0bTRPIL52Ek+eRS/pi3bIsH96e22Q6W/NrAQEfwD+NtFZneAW/Tux
AuKIRWqS7UdqCjLurwMHfR9bOHrBDQI=
=z7pu
-----END PGP SIGNATURE-----
Merge tag 'ovl-fixes-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"Here's one fix for a class of bugs triggered by syzcaller, and one
that makes xfstests fail less"
* tag 'ovl-fixes-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: doc: add non-standard corner cases
ovl: detect overlapping layers
ovl: support the FS_IOC_FS[SG]ETXATTR ioctls
When RST packets are sent because no socket could be found,
it makes sense to use flowlabel_reflect sysctl to decide
if a reflection of the flowlabel is requested.
This extends commit 22b6722bfa ("ipv6: Add sysctl for per
namespace flow label reflection"), for some TCP RST packets.
In order to provide full control of this new feature,
flowlabel_reflect becomes a bitmask.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6250 has port_base_addr 0x8 or 0x18 (depending on
configuration pins), so it constitutes a new family and hence needs
its own compatible string.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible that TCP stack will decide to retransmit a packet
right when that packet's data gets acked, especially in presence
of packet reordering. This means that packets may be in flight,
even though tls_device code has already freed their record state.
Make fill_sg_in() and in turn tls_sw_fallback() not generate a
warning in that case, and quietly proceed to drop such frames.
Make the exit path from tls_sw_fallback() drop monitor friendly,
for users to be able to troubleshoot dropped retransmissions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add binding document for the ethernet on MT7629 SoC.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add an extra required property "mediatek,physpeed" to sgmiisys to determine
link speed to match up the capability of the target PHY.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When isdn4linux came up in the context of another patch series, I
remembered that we had discussed removing it a while ago.
It turns out that the suggestion from Karsten Keil wa to remove I4L
in 2018 after the last public ISDN networks are shut down. This has
happened now (with a very small number of exceptions), so I guess it's
time to try again.
We currently have three ISDN stacks in the kernel: the original
isdn4linux (with the hisax driver), the newer CAPI (with four drivers),
and finally the mISDN stack (supporting roughly the same hardware as
hisax).
As far as I can tell, anyone using ISDN with mainline kernel drivers in
the past few years uses mISDN, and this is typically used for voice-only
PBX installations that don't require a public network.
The older stacks support additional features for data networks, but those
typically make no sense any more if there is no network to connect to.
My proposal for this time is to kill off isdn4linux entirely, as it seems
to have been unusable for quite a while. This code has been abandoned
for many years and it does cause problems for treewide maintenance as
it tends to do everything that we try to stop doing.
Birger Harzenetter mentioned that is is still using i4l in order to
make use of the 'divert' feature that is not part of mISDN, but has
otherwise moved on to mISDN for normal operation, like apparently
everyone else.
CAPI in turn is not quite as obsolete, but two of the drivers (avm
and hysdn) don't seem to be used at all, while another one (gigaset)
will stop being maintained as Paul Bolle is no longer able to
test it after the network gets shut down in September.
All three are now moved into drivers/staging to let others speak
up in case there are remaining users.
This leaves Bluetooth CMTP as the only remaining user of CAPI, but
Marcel Holtmann wishes to keep maintaining it.
For the discussion on version 1, see [2]
Unfortunately, Karsten Keil as the maintainer has not participated in
the discussion.
Arnd
[1] https://patchwork.kernel.org/patch/8484861/#17900371
[2] https://listserv.isdn4linux.de/pipermail/isdn4linux/2019-April/thread.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1ISP
-----END PGP SIGNATURE-----
Merge tag 'isdn-removal' of https://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground
Arnd Bergmann says:
====================
isdn: deprecate non-mISDN drivers
When isdn4linux came up in the context of another patch series, I
remembered that we had discussed removing it a while ago.
It turns out that the suggestion from Karsten Keil wa to remove I4L
in 2018 after the last public ISDN networks are shut down. This has
happened now (with a very small number of exceptions), so I guess it's
time to try again.
We currently have three ISDN stacks in the kernel: the original
isdn4linux (with the hisax driver), the newer CAPI (with four drivers),
and finally the mISDN stack (supporting roughly the same hardware as
hisax).
As far as I can tell, anyone using ISDN with mainline kernel drivers in
the past few years uses mISDN, and this is typically used for voice-only
PBX installations that don't require a public network.
The older stacks support additional features for data networks, but those
typically make no sense any more if there is no network to connect to.
My proposal for this time is to kill off isdn4linux entirely, as it seems
to have been unusable for quite a while. This code has been abandoned
for many years and it does cause problems for treewide maintenance as
it tends to do everything that we try to stop doing.
Birger Harzenetter mentioned that is is still using i4l in order to
make use of the 'divert' feature that is not part of mISDN, but has
otherwise moved on to mISDN for normal operation, like apparently
everyone else.
CAPI in turn is not quite as obsolete, but two of the drivers (avm
and hysdn) don't seem to be used at all, while another one (gigaset)
will stop being maintained as Paul Bolle is no longer able to
test it after the network gets shut down in September.
All three are now moved into drivers/staging to let others speak
up in case there are remaining users.
This leaves Bluetooth CMTP as the only remaining user of CAPI, but
Marcel Holtmann wishes to keep maintaining it.
For the discussion on version 1, see [2]
Unfortunately, Karsten Keil as the maintainer has not participated in
the discussion.
Arnd
[1] https://patchwork.kernel.org/patch/8484861/#17900371
[2] https://listserv.isdn4linux.de/pipermail/isdn4linux/2019-April/thread.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
memory.stat and other files already consider subtrees in their output, and
we should too in order to not present an inconsistent interface.
The current situation is fairly confusing, because people interacting with
cgroups expect hierarchical behaviour in the vein of memory.stat,
cgroup.events, and other files. For example, this causes confusion when
debugging reclaim events under low, as currently these always read "0" at
non-leaf memcg nodes, which frequently causes people to misdiagnose breach
behaviour. The same confusion applies to other counters in this file when
debugging issues.
Aggregation is done at write time instead of at read-time since these
counters aren't hot (unlike memory.stat which is per-page, so it does it
at read time), and it makes sense to bundle this with the file
notifications.
After this patch, events are propagated up the hierarchy:
[root@ktst ~]# cat /sys/fs/cgroup/system.slice/memory.events
low 0
high 0
max 0
oom 0
oom_kill 0
[root@ktst ~]# systemd-run -p MemoryMax=1 true
Running as unit: run-r251162a189fb4562b9dabfdc9b0422f5.service
[root@ktst ~]# cat /sys/fs/cgroup/system.slice/memory.events
low 0
high 0
max 7
oom 1
oom_kill 1
As this is a change in behaviour, this can be reverted to the old
behaviour by mounting with the `memory_localevents' flag set. However, we
use the new behaviour by default as there's a lack of evidence that there
are any current users of memory.events that would find this change
undesirable.
akpm: this is a behaviour change, so Cc:stable. THis is so that
forthcoming distros which use cgroup v2 are more likely to pick up the
revised behaviour.
Link: http://lkml.kernel.org/r/20190208224419.GA24772@chrisdown.name
Signed-off-by: Chris Down <chris@chrisdown.name>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix Sphinx warnings in Documentation/vm/hmm.rst by using "::" notation and
inserting a blank line. Also add a missing ';'.
Documentation/vm/hmm.rst:292: WARNING: Unexpected indentation.
Documentation/vm/hmm.rst:300: WARNING: Unexpected indentation.
Link: http://lkml.kernel.org/r/c5995359-7c82-4e47-c7be-b58a4dda0953@infradead.org
Fixes: 023a019a9b ("mm/hmm: add default fault flags to avoid the need to pre-fill pfns arrays")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Jérôme Glisse <jglisse@redhat.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-05-31
The following pull-request contains BPF updates for your *net-next* tree.
Lots of exciting new features in the first PR of this developement cycle!
The main changes are:
1) misc verifier improvements, from Alexei.
2) bpftool can now convert btf to valid C, from Andrii.
3) verifier can insert explicit ZEXT insn when requested by 32-bit JITs.
This feature greatly improves BPF speed on 32-bit architectures. From Jiong.
4) cgroups will now auto-detach bpf programs. This fixes issue of thousands
bpf programs got stuck in dying cgroups. From Roman.
5) new bpf_send_signal() helper, from Yonghong.
6) cgroup inet skb programs can signal CN to the stack, from Lawrence.
7) miscellaneous cleanups, from many developers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There has been quite a few progress around the two steps mentioned in the
answer to the following question:
Q: BPF 32-bit subregister requirements
This patch updates the answer to reflect what has been done.
v2:
- Add missing full stop. (Song Liu)
- Minor tweak on one sentence. (Song Liu)
v1:
- Integrated rephrase from Quentin and Jakub
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
