These functions need to be reworked for Ironlake and above, but until
then at least avoid reading non-existent registers.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: combine with a gratuitous tidy]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When bringing up new hardware, or otherwise experimenting, GPU hangs are
a way of life. However, the automatic GPU reset can do more harm than
good under these circumstances, as we may wish to capture a full trace for
debugging.
Based on a patch by Zhenyu Wang.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On Ironlake, the LP0 latency is hardcoded and in ns unit, while on
Sandybridge, it comes from a register and with unit 0.1 us. So, fix
the wrong latency value while computing wm0 on Ironlake and Sandybridge.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This patch actually makes the watermark code even uglier (if that's
possible), but has the advantage of sharing code between SNB and ILK at
least. Longer term we should refactor the watermark stuff into its own
file and clean it up now that we know how it's supposed to work.
Supporting WM2 on my Vaio reduced power consumption by around 0.5W, so
this patch is definitely worthwhile (though it also needs lots of test
coverage).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: pass the watermark structs arounds]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On i830 if the tail pointer is set to within 2 cachelines of the end of
the buffer, the chip may hang. So instead if the tail were to land in
that location, we pad the end of the buffer with NOPs, and start again
at the beginning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In some configuration, the PCU may allow us to overclock the GPU.
Check for this case and adjust the max frequency as appropriate. Also
initialize the min/max frequencies to default values as indicated by
hardware.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... and just any combination of bits & ~PFIT_ENABLE. This way we do not
attempt disable to the panel fitter controller uselessly upon
intel_lvds_disable().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By tracking the current status of the backlight we can prevent recording
the value of the current backlight when we have disabled it. And so
prevent restoring it to 'off' after an unbalanced sequence of
intel_lvds_disable/enable.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=22672
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Alex Fiestas reported an issue with his HDMI connector being misdetected
as DVI unless he had something connected upon boot. By moving the
decision as to whether to use HDMI or DVI encoding for the HDMI capable
output until we probe the monitor means that we should avoid sending a
HDMI signal to a DVI monitor and also correctly detect hardware like
Alex's.
However, to really determine what connector is soldered onto the wire we
need to inspect the VBT sdvo child devices - but can we trust it?
Reported-by: Alex Fiestas <alex@eyeos.org>
Tested-by: Alex Fiestas <alex@eyeos.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32828
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Some voltage swing/pre-emphasis level use the same value on eDP
Sandybridge, like 400mv_0db and 600mv_0db are with the same value
of (0x0 << 22). So, fix them, and point out the value if it isn't
a supported voltage swing/pre-emphasis level.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Since Linux 2.6.36 the digital output on my system (855GME + DVI-I) is
not working any longer. The analog output is always activated
regardless of the type of monitor attached.
The culprit seems to be intel_crt_detect_ddc(), which returns true as
soon as an ACK from the EDID device is received. Obviously this
approach does not work with DVI-I where the analog and digital outputs
share a common DDC bus.
In a similar manner to the shared DDC wire, ala the "Mac Mini Hack", we
need an additional check to make sure that there really is an analog
device attached to the DDC.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
When trying to do channel equalization, we need to make sure we still
have clock recovery on all lanes while training. We also need to try
clock recovery again if we lose the clock or if channel eq fails 5
times. We'll try clock recovery up to 5 more times before giving up
entirely.
Gets suspend/resume working on my Vaio again and brings us back into
compliance with the DP training sequence spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We were using a stale pointer in the check which caused us to use CPU
attached DP params when we should have been using PCH attached params.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31988
Tested-by: Jan-Hendrik Zab <jan@jhz.name>
Tested-by: Christoph Lukas <christoph.lukas@gmx.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (390 commits)
drm/radeon/kms: disable underscan by default
drm/radeon/kms: only enable hdmi features if the monitor supports audio
drm: Restore the old_fb upon modeset failure
drm/nouveau: fix hwmon device binding
radeon: consolidate asic-specific function decls for pre-r600
vga_switcheroo: comparing too few characters in strncmp()
drm/radeon/kms: add NI pci ids
drm/radeon/kms: don't enable pcie gen2 on NI yet
drm/radeon/kms: add radeon_asic struct for NI asics
drm/radeon/kms/ni: load default sclk/mclk/vddc at pm init
drm/radeon/kms: add ucode loader for NI
drm/radeon/kms: add support for DCE5 display LUTs
drm/radeon/kms: add ni_reg.h
drm/radeon/kms: add bo blit support for NI
drm/radeon/kms: always use writeback/events for fences on NI
drm/radeon/kms: adjust default clock/vddc tracking for pm on DCE5
drm/radeon/kms: add backend map workaround for barts
drm/radeon/kms: fill gpu init for NI asics
drm/radeon/kms: add disabled vbios accessor for NI asics
drm/radeon/kms: handle NI thermal controller
...
Lots of HDMI TVs overscan the incoming image by default.
The underscan option was added as a way to compensate for
that by underscanning the image so that the edges would
not be cut off on an overscanning TV. However, the TV
provides no way of knowing whether it is overscanning or
not. If the user has disabled overscan on their TV or has a
TV that does not overscan, you will get black bars around the
edges of your screen. Prior to the patch we got complaints
and bug reports from users with overscanning TVs, now with
the patch, we get lots of complaints and bug reports from
users with non-overscanning TVs. There's no good default,
but on average there have been more users complaining about
it being on by default than off, so change it to off. This
will probably result in a new deluge of overscanning TV user
complaints. There's no winning.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This avoids some issues in the current hdmi audio code for monitors
without audio.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-ni' of ../drm-radeon-next: (30 commits)
radeon: consolidate asic-specific function decls for pre-r600
drm/radeon/kms: add NI pci ids
drm/radeon/kms: don't enable pcie gen2 on NI yet
drm/radeon/kms: add radeon_asic struct for NI asics
drm/radeon/kms/ni: load default sclk/mclk/vddc at pm init
drm/radeon/kms: add ucode loader for NI
drm/radeon/kms: add support for DCE5 display LUTs
drm/radeon/kms: add ni_reg.h
drm/radeon/kms: add bo blit support for NI
drm/radeon/kms: always use writeback/events for fences on NI
drm/radeon/kms: adjust default clock/vddc tracking for pm on DCE5
drm/radeon/kms: add backend map workaround for barts
drm/radeon/kms: fill gpu init for NI asics
drm/radeon/kms: add disabled vbios accessor for NI asics
drm/radeon/kms: handle NI thermal controller
drm/radeon/kms: parse DCE5 encoder caps when setting up encoders
drm/radeon/kms: dvo dpms updates for DCE5
drm/radeon/kms: dac dpms updates for DCE5
drm/radeon/kms: DCE5 atom dig encoder updates
drm/radeon/kms: DCE5 atom transmitter control updates
...
* 'nouveau/drm-nouveau-next' of ../drm-nouveau-next:
drm/nouveau: fix hwmon device binding
drm/nouveau: create grctx on the fly on all chipsets
drm/nvc0: fix init without firmware present
drm/nvc0/pgraph: fix 0x406028/0x405870 init
drm/nvc0/pgraph: more unit names
drm/nvc0/pfifo: support for chipsets with only one PSUBFIFO (0xc1)
drm/nvc0: reserve only subc 0 for kernel use
drm/nv50: sync up gr data error names with rnn, use for nvc0 also
drm/nvc0: parse a couple more PGRAPH_INTR
drm/nvc0: nuke left-over debug messages
drm/nvc0: kill off a couple more magics
drm/nouveau: Validate channel indices passed from userspace.
drm/nouveau: Only select ACPI_VIDEO if its dependencies are met
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
Bind the hwmon structs to nouveau device kobj. This makes sure
the hwmon files are created in the device subdir in line with
all other hwmon drivers.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Move them to radeon_asic.h together with the other asic
specific stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vbios only partially initializes the memory controller on
NI, so now we need to load the MC ucode in the driver and set
the default clocks once the ucode is loaded.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The MC ucode is no longer loaded by the vbios
tables as on previous asics. It now must be loaded
by the driver.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The hardware supports advanced user defined color management
but at the moment, there is no infrastructure in place to take
advantage of it so for now we just support the legacy LUTs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds some new NI (northern islands) specific display
register defines.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
NI chips no longer load the MC ucode in the asic_init sequence so
the asic comes up in a basic mode with low engine/memory clocks and
a voltage. Once the MC ucode is loaded by the driver the card
can be programmed to it's proper default clocks and voltage. As such
the default clocks in the firmware info table as the post clocks, not
the default running clocks. Track the default post clocks and default
running clocks separately to handle this.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some systems disable the vbios on secondary cards or cards that
have been posted. This code re-enabled the vbios so the driver
can load it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Needed to tell which DIG encoders are HBR2 capable for DP 1.2.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DVOOutputControl table was removed for DCE5.
DVOEncoderControl now handles everything.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DAC1OutputControl table was removed for DCE5.
DAC1EncoderControl now handles everything.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Supported on rv6xx/r7xx/evergreen. Cards come up in gen1 mode.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
