This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The regular RX path has a lot of code, but with a few
assumptions on the hardware it's possible to reduce the
amount of code significantly. Currently the assumptions
on the driver are the following:
* hardware/driver reordering buffer (if supporting aggregation)
* hardware/driver decryption & PN checking (if using encryption)
* hardware/driver did de-duplication
* hardware/driver did A-MSDU deaggregation
* AP_LINK_PS is used (in AP mode)
* no client powersave handling in mac80211 (in client mode)
of which some are actually checked per packet:
* de-duplication
* PN checking
* decryption
and additionally packets must
* not be A-MSDU (have been deaggregated by driver/device)
* be data packets
* not be fragmented
* be unicast
* have RFC 1042 header
Additionally dynamically we assume:
* no encryption or CCMP/GCMP, TKIP/WEP/other not allowed
* station must be authorized
* 4-addr format not enabled
Some data needed for the RX path is cached in a new per-station
"fast_rx" structure, so that we only need to look at this and
the packet, no other memory when processing packets on the fast
RX path.
After doing the above per-packet checks, the data path collapses
down to a pretty simple conversion function taking advantage of
the data cached in the small fast_rx struct.
This should speed up the RX processing, and will make it easier
to reason about parallelizing RX (for which statistics will need
to be per-CPU still.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Legacy clients don't support P2P power save mechanism, and thus if a P2P GO
has a legacy client connected to it, it should disable P2P PS mechanisms.
Let the driver know about this with a new bss_conf parameter.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh path and mesh gate hashtables are global, containing
all of the mpaths for every mesh interface, but the paths are
all tied logically to a single interface. The common case is
just a single mesh interface, so optimize for that by moving
the global hashtable into the per-interface struct.
Doing so allows us to drop sdata pointer comparisons inside
the lookups and also saves a few bytes of BSS and data.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers/devices might want to set the IVs by
themselves (and still let mac80211 generate MMIC).
Specifically, this is needed when the device does
offloading at certain times, and the driver has
to make sure that the IVs of new tx frames (from
the host) are synchronized with IVs that were
potentially used during the offloading.
Similarly to CCMP, move the TX IVs of TKIP keys to the
public part of the key struct, and export a function
to add the IV right into the crypto header.
The public tx_pn field is defined as atomic64, so define
TKIP_PN_TO_IV16/32 helper macros to convert it to iv16/32
when needed.
Since the iv32 used for the p1k cache is taken
directly from the frame, we can safely remove
iv16/32 from being protected by tkip.txlock.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In VHT, the specification allows to limit the number of
MSDUs in an A-MSDU in the Extended Capabilities IE. There
is also a limitation on the byte size in the VHT IE.
In HT, the only limitation is on the byte size.
Parse the capabilities from the peer and make them
available to the driver.
In HT, there is another limitation when a BA agreement
is active: the byte size can't be greater than 4095.
This is not enforced here.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
An AP can send an operating channel width change in a beacon
opmode notification IE as long as there's a change in the nss as
well (See 802.11ac-2013 section 10.41).
So don't limit updating to nss only from an opmode notification IE.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the cookie is assigned inside ieee80211_make_ack_skb()
now, we no longer need to return the ack_skb as the cookie
and can simplify the function's return and the callers. Also
rename it to ieee80211_attach_ack_skb() to more accurately
reflect its purpose.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is quite a bit of code that logically depends here since
it has to deal with all the remain-on-channel logic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When freeing the TX skb for an off-channel TX, use the correct
API to also free the ACK skb that might have been allocated.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a new station is added to AP/GO interfaces the default behaviour
is for it to be added authenticated and associated, due to backwards
compatibility. To prevent that, the driver must be able to do that
(setting the NL80211_FEATURE_FULL_AP_CLIENT_STATE feature flag) and
userspace must set the flag mask to auth|assoc and clear the set.
Handle this quirk in the API entirely in nl80211, and always push the
full flags to the drivers. NL80211_FEATURE_FULL_AP_CLIENT_STATE is
still required for userspace to be allowed to set the mask including
those bits, but after checking that add both flags to the mask and
set in case userspace didn't set them otherwise.
This obsoletes the mac80211 code handling this difference, no other
driver is currently using these flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit adds implementation for abort scan in mac80211.
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
[adjust to wdev change in previous patch and clean up code a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the last change here, I neglected to update the cookie in one code
path: when a mgmt-tx has no real cookie sent to userspace as it doesn't
wait for a response, but is off-channel. The original code used the SKB
pointer as the cookie and always assigned the cookie to the TX SKB in
ieee80211_start_roc_work(), but my change turned this around and made
the code rely on a valid cookie being passed in.
Unfortunately, the off-channel no-wait TX path wasn't assigning one at
all, resulting in an uninitialized stack value being used. This wasn't
handed back to userspace as a cookie (since in the no-wait case there
isn't a cookie), but it was tested for non-zero to distinguish between
mgmt-tx and off-channel.
Fix this by assigning a dummy non-zero cookie unconditionally, and get
rid of a misleading comment and some dead code while at it. I'll clean
up the ACK SKB handling separately later.
Fixes: 3b79af973c ("mac80211: stop using pointers as userspace cookies")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Scheduled scan has to be reconfigured only if wowlan wasn't
configured, since otherwise it should continue to run (with
the 'any' trigger) or be aborted.
The current code will end up asking the driver to start a new
scheduled scan without stopping the previous one, and leaking
some memory (from the previous request.)
Fix this by doing the abort/restart under the proper conditions.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's only a single caller of this function, so it can
be moved to the same file and made static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As this API has never really seen any use and most drivers don't
ever use the value derived from it, remove it.
Change the only driver using it (rt2x00) to simply use the DTIM
period instead of the "max sleep" time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 5c48f12017.
Some device drivers (ath10k) offload part of aggregation including AddBA/DelBA
negotiations to firmware. In such scenario, the PMF configuration of
the station needs to be provided to driver to enable encryption of
AddBA/DelBA action frames.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* many internal fixes, API improvements, cleanups, etc.
* full AP client state tracking in cfg80211/mac80211 from Ayala
* VHT support (in mac80211) for mesh
* some A-MSDU in A-MPDU support from Emmanuel
* show current TX power to userspace (from Rafał)
* support for netlink dump in vendor commands (myself)
-----BEGIN PGP SIGNATURE-----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=BF9F
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-10-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For the current cycle, we have the following right now:
* many internal fixes, API improvements, cleanups, etc.
* full AP client state tracking in cfg80211/mac80211 from Ayala
* VHT support (in mac80211) for mesh
* some A-MSDU in A-MPDU support from Emmanuel
* show current TX power to userspace (from Rafał)
* support for netlink dump in vendor commands (myself)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables adding stations in unauthenticated mode, just after
receiving the first authentication frame; which in turn allows
sending a negative authentication reply if the station cannot be
added.
In addition init rate control for unassociated station only when
it becomes associated, prior to that low rates will be used.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current behavior of notifying CQM events is inconsistent:
Upon first configuration there is a cqm event with the current
status according to threshold configured, regardless of signal
stability.
When there is reconfiguration no event is sent unless there is
a significant change to the signal level according to the new
configuration.
Since the current reconfiguration behavior might cause missing
CQM events in case the current signal did not change but is on
the other side of the new threshold, fix that by resetting the
stored signal level upon reconfiguration.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the cfg80211's frame registration api receives wdev, however
mac80211 assumes per device filter configuration and ignores wdev.
Per device filtering is too wasteful, especially for multi-channel
devices.
Introduce new per vif frame registration API and use it for probe
request registrations in ieee80211_mgmt_frame_register()
Also call directly to ieee80211_configure_filter instead of using a work
since it is now allowed to sleep in ieee80211_mgmt_frame_register.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes we are interested in testing TDLS performance in a specific
width setting. Add the ability to disable the wider-band feature, thereby
allowing the TDLS channel width to be controlled by the BSS width.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The HT MCS mask has 9 bytes, the VHT one only has 8 streams.
Split the loops to handle this correctly.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When beacon filtering is enabled the mac80211 software implementation
for RSSI CQM cannot work as beacons will not be available. Rather than
accepting such a configuration without proper effect, reject it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define rc_rateidx_vht_mcs_mask array and rate_idx_match_vht_mcs_mask()
method in order to apply mcs mask for vht rates
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The IEEE802.11-2012 specification is vague regarding SMPS operation during
TDLS. It does not define a clear way to transition between SMPS states.
To avoid interop issues, set SMPS to off when TDLS peers are connected.
Accomplish this by extending the definition of the AUTOMATIC state. If the
driver forces a state other than OFF, disconnect all TDLS peers.
While at it, avoid changing the SMPS state of the peer STA. We have no
way to control it, so try and behave correctly towards it.
Move the TDLS peer-teardown function to where the rest of the TDLS code
resides.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow a device to specify support for the TDLS wider-bandwidth feature.
Indicate this support during TDLS setup in the ext-capab IE and set an
appropriate station flag when our TDLS peer supports it.
This feature gives TDLS peers the ability to use a wider channel than
the base width of the BSS. For instance VHT capable TDLS peers connected
on a 20MHz channel can extend the channel to 80MHz, if regulatory
considerations allow it.
Do not cap the bandwidth of such stations by the current BSS channel width
in mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code was always a bit awkward due to the 80-col restriction
and got worse in the previous patch. Refactor it a bit into its
own function to make it read nicer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are now a fairly large number of mesh fields that really
aren't needed in any other modes; move those into their own
structure and allocate them separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge back net-next to get wireless driver changes (from Kalle)
to be able to create the API change across all trees properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The csa counter has moved from sdata to beacon/presp but
it is not updated accordingly for mesh and ibss. Fix this.
Fixes: af296bdb8d ("mac80211: move csa counters from sdata to beacon/presp")
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even if the pointers are really only accessible to root and used
pretty much only by wpa_supplicant, this is still not great; even
for debugging it'd be easier to have something that's easier to
read and guaranteed to never get reused.
With the recent change to make mac80211 create an ack_skb for the
mgmt-tx path this becomes possible, only the client probe method
needs to also allocate an ack_skb, and we can store the cookie in
that skb.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we return the TX status for an nl80211 mgmt TX SKB, we
should also return the original frame with the status to
allow userspace to match up the submission (it could also
use the cookie but both ways are permissible.)
As TX SKBs could be encrypted, at least in the case of ANQP
while associated with the AP, copy the original SKB, store
it with an ACK frame ID and restructure the status path to
use that to return status with the original SKB. Otherwise,
userspace (in particular wpa_supplicant) will get confused.
Reported-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For drivers supporting TSO or similar features, but that still have
PN assignment in software, there's a need to have some memory to
store the current PN value. As mac80211 already stores this and it's
somewhat complicated to add a per-driver area to the key struct (due
to the dynamic sizing thereof) it makes sense to just move the TX PN
to the keyconf, i.e. the public part of the key struct.
As TKIP is more complicated and we won't able to offload it in this
way right now (fast-xmit is skipped for TKIP unless the HW does it
all, and our hardware needs MMIC calculation in software) I've not
moved that for now - it's possible but requires exposing a lot of
the internal TKIP state.
As an bonus side effect, we can remove a lot of code by assuming the
keyseq struct has a certain layout - with BUILD_BUG_ON to verify it.
This might also improve performance, since now TX and RX no longer
share a cacheline.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to remain-on-channel scheduling delays, when we split an ROC
while coalescing, we'll usually get a picture like this:
existing ROC: |------------------|
current time: ^
new ROC: |------| |-------|
If the expected response frames are then transmitted by the peer
in the hole between the two fragments of the new ROC, we miss
them and the process (e.g. ANQP query) fails.
mac80211 expects that the window to miss something is small:
existing ROC: |------------------|
new ROC: |------||-------|
but that's normally not the case.
To avoid this problem, coalesce only if the new ROC's duration
is <= the remaining time on the existing one:
existing ROC: |------------------|
new ROC: |-----|
and never split a new one but schedule it afterwards instead:
existing ROC: |------------------|
new ROC: |-------------|
type=bugfix
bug=not-tracked
fixes=unknown
Reported-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: EliadX Peller <eliad@wizery.com>
Reviewed-by: Matti Gottlieb <matti.gottlieb@intel.com>
Tested-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers with fast-xmit (e.g. ath10k) running in
AP_VLAN setups would fail to communicate with
connected 4addr stations.
The reason was when new station associates it
first goes into master AP interface. It is not
until later that a dedicated AP_VLAN is created
for it and the station itself is moved there.
After that Tx directed at the station should use
4addr header. However fast-xmit wasn't
recalculated and 3addr header remained to be used.
This in turn caused the connected 4addr stations
to drop packets coming from the AP until some
other event would cause fast-xmit to recalculate
for that station (which could never come).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For ciphers not supported by mac80211, the function currently
doesn't return any PN data. Fix this by extending the driver's
get_key_seq() a little more to allow moving arbitrary PN data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend the function to read the TKIP IV32/IV16 to read the IV/PN for
all ciphers in order to allow drivers with full hardware crypto to
properly support this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently while associated to an AP and sending a (public) action
frame to a different AP on the same channel, the action frame will
be sent like a regular tx frame without going off channel.
When power save is enabled this can cause problems, since the device
can go into power save and miss the response to the action frame
that is sent by the other AP.
Force off-channel transmission to avoid this issue in case
- HW offchannel is used,
- the user didn't forbid transmitting frames off channel
- the frame is not sent to the AP that we are associated with
(if it is we assume the response would be bufferable)
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to speed up mac80211's TX path, add the "fast-xmit" cache
that will cache the data frame 802.11 header and other data to be
able to build the frame more quickly. This cache is rebuilt when
external triggers imply changes, but a lot of the checks done per
packet today are simplified away to the check for the cache.
There's also a more detailed description in the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
-----BEGIN PGP SIGNATURE-----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=O/cf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Lots of updates for net-next; along with the usual flurry
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the upcoming fast-xmit patch, changing station state will
build a header cache based on the station's capabilities, and
as the QoS capability (sta.wme) impacts the header, it needs
to be set before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Indicating just the peer's capability is fairly pointless
if the local device doesn't support it. Make the variable
track both combined, and remove the 'local support' check
in the TX path.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will expose in /sys whether the ifname of a device is set by
userspace or generated by the kernel. The latter kind (wlanX, etc)
is not deterministic, so userspace needs to rename these devices
to names that are guaranteed to stay the same between reboots. The
former, however should never be renamed, so userspace needs to be
able to reliably tell the difference.
Similar functionality was introduced for the rtnetlink core in
commit 5517750f05 ("net: rtnetlink - make create_link take name_assign_type")
Signed-off-by: Tom Gundersen <teg@jklm.no>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
[reformat changelog to fit 72 cols]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
