Adds DMA Engine framework support into RapidIO subsystem.
Uses DMA Engine DMA_SLAVE interface to generate data transfers to/from
remote RapidIO target devices.
Introduces RapidIO-specific wrapper for prep_slave_sg() interface with an
extra parameter to pass target specific information.
Uses scatterlist to describe local data buffer. Address flat data buffer
on a remote side.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add RapidIO mport driver for IDT TSI721 PCI Express-to-SRIO bridge device.
The driver provides full set of callback functions defined for mport
devices in RapidIO subsystem. It also is compatible with current version
of RIONET driver (Ethernet over RapidIO messaging services).
This patch is applicable to kernel versions starting from 2.6.39.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Chul Kim <chul.kim@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add debug configuration option for RapidIO subsystem.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the functionality to enable Input receiver and Output transmitter of
every port, to allow non-maintenance traffic.
Signed-off-by: Thomas Moll <thomas.moll@sysgo.com>
Signed-off-by: Alexandre Bounine <abounine@tundra.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Extentions to RapidIO switch support:
1. modify switch route operation declarations to allow using single
switch-specific file for family of switches that share the same route
table operations.
2. add standard route table operations for switches that that support
route table manipulation registers as defined in the Rev.1.3 of RapidIO
specification.
3. add clear-route-table operation for switches
4. add CPSxx and TSIxxx families of RapidIO switches
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Tested-by: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RapidIO system size will auto probe in RIO setup. The route table
and rionet_active in rionet.c are changed to be allocated dynamically
according to the size of the system.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds a RapidIO subsystem to the kernel. RIO is a switched fabric interconnect
used in higher-end embedded applications. The curious can look at the specs
over at http://www.rapidio.org
The core code implements enumeration/discovery, management of
devices/resources, and interfaces for RIO drivers.
There's a lot more to do to take advantages of all the hardware features.
However, this should provide a good base for folks with RIO hardware to start
contributing.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
