Several implementations were essentialy a common piece of C code using
the cmpxchg() macro. Put the implementation in one spot that everyone
can share, and convert sparc64 over to using this.
Alpha is the lone arch-specific implementation, which codes up a
special fast path for the common case in order to avoid GP reloading
which a pure C version would require.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 66759a01ad introduced the fix for
time ticking too fast on some boards by disabling one of the doubly
connected timer pins on ATI boards.
However, it ends up being _much_ too broad a brush, and that just makes
some other ATI boards not work at all since they now have no timer
source.
So disable the automatic ATI southbridge detection, and just rely on
people who see this problem disabling it by hand with the option
"disable_timer_pin_1" on the kernel command line.
Maybe somebody can figure out the proper tests at a later date.
Acked-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pavel Emelianov and Kirill Korotaev observe that fs and arch users of
security_vm_enough_memory tend to forget to vm_unacct_memory when a
failure occurs further down (typically in setup_arg_pages variants).
These are all users of insert_vm_struct, and that reservation will only
be unaccounted on exit if the vma is marked VM_ACCOUNT: which in some
cases it is (hidden inside VM_STACK_FLAGS) and in some cases it isn't.
So x86_64 32-bit and ppc64 vDSO ELFs have been leaking memory into
Committed_AS each time they're run. But don't add VM_ACCOUNT to them,
it's inappropriate to reserve against the very unlikely case that gdb
be used to COW a vDSO page - we ought to do something about that in
do_wp_page, but there are yet other inconsistencies to be resolved.
The safe and economical way to fix this is to let insert_vm_struct do
the security_vm_enough_memory check when it finds VM_ACCOUNT is set.
And the MIPS irix_brk has been calling security_vm_enough_memory before
calling do_brk which repeats it, doubly accounting and so also leaking.
Remove that, and all the fs and arch calls to security_vm_enough_memory:
give it a less misleading name later on.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-Off-By: Kirill Korotaev <dev@sw.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Like previously done for i386, get the x86_64 watchdog tick calculation
into a state where it can also be used on CPUs with frequencies beyond
4GHz.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the add_taint() interface for setting tainted bit flags instead of
doing it manually.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Original patch from Bertro Simul
This is probably still not quite correct, but seems to be
the best solution so far.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As mentioned before, the size of the bug frame can be further reduced while
continuing to use instructions to encode the information.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... and with that all instances in arch/x86_64 are gone.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the same patch that went into i386 just before 2.6.13
came out. I still can't build 64-bit user apps, so I tested
with program (see below) in 32-bit mode on 64-bit kernel:
Before:
$ fpsig
handler: nr = 8, si = 0x0804bc90, vuc = 0x0804bd10
handler: altstack is at 0x0804b000, ebp = 0x0804bc7c
handler: si_signo = 8, si_errno = 0, si_code = 0 [unknown]
handler: fpu cwd = 0xb40, fpu swd = 0xbaa0
handler: i387 unmasked precision exception, rounded up
After:
$ fpsig
handler: nr = 8, si = 0x0804bc90, vuc = 0x0804bd10
handler: altstack is at 0x0804b000, ebp = 0x0804bc7c
handler: si_signo = 8, si_errno = 0, si_code = 6 [inexact result]
handler: fpu cwd = 0xb40, fpu swd = 0xbaa0
handler: i387 unmasked precision exception, rounded up
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The x86_64 nmi code is missing a newline in one of its messages.
I added a space before the CPU id for readability and killed the trailing
space on the previous line as well.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rather than blindly re-enabling interrupts in oops_end(), save their state
in oope_begin() and then restore that state.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The only difference was the inline assembly, so move that into
asm/msr.h and merge with the i386 version.
This adds some missing sysfs support code to x86-64.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Being the foundation for reliable stack unwinding, this fixes CFI unwind
annotations in many low-level x86_64 routines, plus a config option
(available to all architectures, and also present in the previously sent
patch adding such annotations to i386 code) to enable them separatly
rather than only along with adding full debug information.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Report PXMs instead of nodes
- Report the correct PXM, not always the one of node 1.
- Only warn for the case of a PXM overlapping by itself
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nick points out it never worked because PageReserved was
set and it might cause problems later on. Also HOTPLUG_CPU
is much more common now so let's care not too much
about the !hotplug case.
Cc: nickpiggin@yahoo.com.au
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It only offers extremly dubious security advantages and
is not worth the overhead in this critical path.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The global bit was not set in the first 2MB page, instead
it had a bit in the free AVL section which is useless.
Fixed thus.
Noticed by Eric Biederman
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86_64 idle=poll might be a little less responsive than it should: unlike
mwait_idle, and unlike i386, its poll_idle left TIF_POLLING_NRFLAG set.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds console and earlyprintk support for a host file
on AMD's SimNow simulator.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of using a global spinlock to protect the state
of the remote TLB flush use a lock and state for each sending CPU.
To tell the receiver where to look for the state use 8 different
call vectors. Each CPU uses a specific vector to trigger flushes on other
CPUs. Depending on the received vector the target CPUs look into
the right per cpu variable for the flush data.
When the system has more than 8 CPUs they are hashed to the 8 available
vectors. The limited global vector space forces us to this right now.
In future when interrupts are split into per CPU domains this could be
fixed, at the cost of needing more IPIs in flat mode.
Also some minor cleanup in the smp flush code and remove some outdated
debug code.
Requires patch to move cpu_possible_map setup earlier.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we use 64bit kernel on ia64/x86_64/s390 architecture, and we run
32bit binary on 32bit compatibility mode, sendfile system call seems be
not set offset argument.
This is because sendfile's return value is not zero but the code regards
the result by return value is zero or not.
This problem will be affect to ia64/x86_64/s390 and not affect to other
architecture does not affect other architecture (mips/parisc/ppc64/sparc64).
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Include build number in oops output
Helps me to match oopses to correct kernel.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The resume code uses CPU hotplug now so at resume time
we only ever see one CPU.
Pointed out by Yu Luming.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The FLATMEM people added it, but there doesn't seem a good reason
because end_pfn is identical.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It could be wrong for kexec or other cases. Read it from
the CPU instead.
Signed-off-by: Murali <muralim@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One machine is constantly throwing NMI watchdog timeouts in mce_log
This was one attempt to fix it.
(AK: this doesn't actually fix the bug I'm seeing unfortunately, probably
drop. I don't like it that the reader can spin forever now waiting
for a writer)
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Originally from Stuart Hayes.
When setting up the APIC for the Uniprocessor kernel don't
assume the CPU has an APIC ID of zero.
This fixes boot with the UP kernel on Dell PowerEdge 6800/6850 4way systems.
Cc: Stuart.Hayes@dell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In particular on systems where the local APIC space and node space
is very different from the Linux CPU number space.
Previously the older NUMA setup code directly parsing the K8
northbridge registers had some issues on 8 socket or dual core
systems. This patch fixes them.
This is mainly done by fixing some confusion between Linux
CPU numbers and local APIC ids. We now pass the local APIC IDs
to later code, which avoids mismatches.
Also add some heuristics to detect cases where the Hypertransport
nodeids and the local APIC IDs don't match, but are shifted
by a constant offset.
This is still all quite hackish, hopefully BIOS writers fill
in correct SRATs instead.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do that later when the CPU boots. SRAT just stores the APIC<->Node
mapping node. This fixes problems on systems where the order
of SRAT entries does not match the MADT.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We used to disable them to work around a bug, but that
is not needed anymore. Keeping them enabled avoids the NMI
watchdog triggering in some cases.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Handles case where BIOS gives CPUs very large APIC numbers correctly.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This was just needed for the Numasaurus, which fortunately
doesn't support x86-64 CPUs.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No x86-64 chipset has this bug
Generated code doesn't change because it was always disabled.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that Greg implemented MCFG/_SEG support this shouldn't be needed
anymore
Cc: gregkh@suse.de
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the new macros for x86_64 too.
Note that the current scripts includes different definitions; more exactly,
it only contains part of the DWARF2 sections and the .comment one from
Stabs. Shouldn't be a problem, anyway.
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
get_cpu_vendor() no longer has any users in other files.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes the problem with "Averatec 6240 pcmcia_socket0: unable to
apply power", which was due to the CardBus IOMEM register region being
allocated at an address that was actually inside the RAM window that had
been reserved for video frame-buffers in an UMA setup.
The BIOS _should_ have marked that region reserved in the e820 memory
descriptor tables, but did not.
It is fixed by rounding up the default starting address of PCI memory
allocations, so that we leave a bigger gap after the final known memory
location. The amount of rounding depends on how big the unused memory
gap is that we can allocate IOMEM from.
Based on example code by Linus.
Acked-by: Greg KH <greg@kroah.com>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds a lost fput in 32bit tiocgdev ioctl on x86-64
[ chrisw: Updated to use fget_light/fput_light ]
Signed-Off-By: Kirill Korotaev <dev@sw.ru>
Signed-Off-By: Maxim Giryaev <gem@sw.ru>
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
enforce_max_cpus nukes out cpu_present_map and cpu_possible_map making it
impossible to add new cpus in the system. Since it doesnt provide any
additional value apart this call and reference is removed.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The use of non-shortcut version of routines breaking CPU hotplug. The option
to select this via cmdline also is deleted with the physflat patch, hence
directly placing this code under CONFIG_HOTPLUG_CPU.
We dont want to use broadcast mode IPI's when hotplug is enabled. This causes
bad effects in send IPI to a cpu that is offline which can trip when the cpu
is in the process of being kicked alive.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sanitized and fixed floppy dependencies: split the messy dependencies for
BLK_DEV_FD by introducing a new symbol (ARCH_MAY_HAVE_PC_FDC), making
BLK_DEV_FD depend on that one and taking declarations of ARCH_MAY_HAVE_PC_FDC
to arch/*/Kconfig. While we are at it, fixed several obvious cases when
BLK_DEV_FD should have been excluded (architectures lacking asm/floppy.h
are *not* going to have floppy.c compile, let alone work).
If you can come up with better name for that ("this architecture might
have working PC-compatible floppy disk controller"), you are more than
welcome - just s/ARCH_MAY_HAVE_PC_FDC/your_prefered_name/g in the patch
below...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a race condition where in system used to hang or sometime
crash within minutes when kprobes are inserted on ISR routine and a task
routine.
The fix has been stress tested on i386, ia64, pp64 and on x86_64. To
reproduce the problem insert kprobes on schedule() and do_IRQ() functions
and you should see hang or system crash.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a bug in kprobes's handling of a corner case on i386 and
x86_64. On an SMP system, if one CPU unregisters a kprobe just after
another CPU hits that probepoint, kprobe_handler() on the latter CPU sees
that the kprobe has been unregistered, and attempts to let the CPU continue
as if the probepoint hadn't been hit. The bug is that on i386 and x86_64,
we were neglecting to set the IP back to the beginning of the probed
instruction. This could cause an oops or crash.
This bug doesn't exist on ppc64 and ia64, where a breakpoint instruction
leaves the IP pointing to the beginning of the instruction. I don't know
about sparc64. (Dave, could you please advise?)
This fix has been tested on i386 and x86_64 SMP systems. To reproduce the
problem, set one CPU to work registering and unregistering a kprobe
repeatedly, and another CPU pounding the probepoint in a tight loop.
Acked-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the x86_64 architecture specific changes to prevent the
possible race conditions.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
64 bit architectures all implement their own compatibility sys_open(),
when in fact the difference is simply not forcing the O_LARGEFILE
flag. So use the a common function instead.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: <viro@parcelfarce.linux.theplanet.co.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch cleans up a commonly repeated set of changes to the NTP state
variables by adding two helper inline functions:
ntp_clear(): Clears the ntp state variables
ntp_synced(): Returns 1 if the system is synced with a time server.
This was compile tested for alpha, arm, i386, x86-64, ppc64, s390, sparc,
sparc64.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mark variables which are usually accessed for reads with __readmostly.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Frank Sorenson <frank@tuxrocks.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Uses of RCU for dynamically changeable NMI handlers need to use the new
rcu_dereference() and rcu_assign_pointer() facilities. This change makes
it clear that these uses are safe from a memory-barrier viewpoint, but the
main purpose is to document exactly what operations are being protected by
RCU. This has been tested on x86 and x86-64, which are the only
architectures affected by this change.
Signed-off-by: <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a new kernel debug feature: CONFIG_DETECT_SOFTLOCKUP.
When enabled then per-CPU watchdog threads are started, which try to run
once per second. If they get delayed for more than 10 seconds then a
callback from the timer interrupt detects this condition and prints out a
warning message and a stack dump (once per lockup incident). The feature
is otherwise non-intrusive, it doesnt try to unlock the box in any way, it
only gets the debug info out, automatically, and on all CPUs affected by
the lockup.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows a valid iommu placed immediately after memory to work, to be
recognized as after the last byte of memory and not overlapping it.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Need to ensure we dont get prempted when we clear ourself from mask when using
clustered mode genapic code.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Up to date I've been using the GS value to determine the processor number
in dumps from show_regs, however this can be cumbersome to do if you don't
have the vmlinux to verify with the address of cpu_pda, how about the
following? I considered using hard_smp_processor_id for robustness but we
already dereference current so we're already relying on MSR_GS_BASE being
sane.
Signed-off-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When handling writes to /proc/irq, current code is re-programming rte
entries directly. This is not recommended and could potentially cause
chipset's to lockup, or cause missing interrupts.
CONFIG_IRQ_BALANCE does this correctly, where it re-programs only when the
interrupt is pending. The same needs to be done for /proc/irq handling as well.
Otherwise user space irq balancers are really not doing the right thing.
- Changed pending_irq_balance_cpumask to pending_irq_migrate_cpumask for
lack of a generic name.
- added move_irq out of IRQ_BALANCE, and added this same to X86_64
- Added new proc handler for write, so we can do deferred write at irq
handling time.
- Display of /proc/irq/XX/smp_affinity used to display CPU_MASKALL, instead
it now shows only active cpu masks, or exactly what was set.
- Provided a common move_irq implementation, instead of duplicating
when using generic irq framework.
Tested on i386/x86_64 and ia64 with CONFIG_PCI_MSI turned on and off.
Tested UP builds as well.
MSI testing: tbd: I have cards, need to look for a x-over cable, although I
did test an earlier version of this patch. Will test in a couple days.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Zwane Mwaikambo <zwane@holomorphy.com>
Grudgingly-acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Coywolf Qi Hunt <coywolf@lovecn.org>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix remaining bits of u32 vs. pm_message confusion. Should not break
anything.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reset the ISA DMA controller into a known state after a suspend. Primary
concern was reenabling the cascading DMA channel (4).
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch moves the common code in x86 and x86-64's semaphore.c into a
single file in lib/semaphore-sleepers.c. The arch specific asm stubs are
left in the arch tree (in semaphore.c for i386 and in the asm for x86-64).
There should be no changes in code/functionality with this patch.
Signed-off-by: Benjamin LaHaise <benjamin.c.lahaise@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It has been reported that the way Linux handles NODEFER for signals is
not consistent with the way other Unix boxes handle it. I've written a
program to test the behavior of how this flag affects signals and had
several reports from people who ran this on various Unix boxes,
confirming that Linux seems to be unique on the way this is handled.
The way NODEFER affects signals on other Unix boxes is as follows:
1) If NODEFER is set, other signals in sa_mask are still blocked.
2) If NODEFER is set and the signal is in sa_mask, then the signal is
still blocked. (Note: this is the behavior of all tested but Linux _and_
NetBSD 2.0 *).
The way NODEFER affects signals on Linux:
1) If NODEFER is set, other signals are _not_ blocked regardless of
sa_mask (Even NetBSD doesn't do this).
2) If NODEFER is set and the signal is in sa_mask, then the signal being
handled is not blocked.
The patch converts signal handling in all current Linux architectures to
the way most Unix boxes work.
Unix boxes that were tested: DU4, AIX 5.2, Irix 6.5, NetBSD 2.0, SFU
3.5 on WinXP, AIX 5.3, Mac OSX, and of course Linux 2.6.13-rcX.
* NetBSD was the only other Unix to behave like Linux on point #2. The
main concern was brought up by point #1 which even NetBSD isn't like
Linux. So with this patch, we leave NetBSD as the lonely one that
behaves differently here with #2.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some nodes can have large holes on x86-64.
This fixes problems with the VM allowing too many dirty pages because it
overestimates the number of available RAM in a node. In extreme cases you
can end up with all RAM filled with dirty pages which can lead to deadlocks
and other nasty behaviour.
This patch just tells the VM about the known holes from e820. Reserved
(like the kernel text or mem_map) is still not taken into account, but that
should be only a few percent error now.
Small detail is that the flat setup uses the NUMA free_area_init_node() now
too because it offers more flexibility.
(akpm: lotsa thanks to Martin for working this problem out)
Cc: Martin Bligh <mbligh@mbligh.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Delete the ability to build an ACPI kernel that does
not include PCI support. When such a machine is created
and it requires a tuned kernel, send a patch.
http://bugzilla.kernel.org/show_bug.cgi?id=1364
Signed-off-by: Len Brown <len.brown@intel.com>
I mistakedly disabled fusion support in an earlier update. Fusion
is commonly used on many x86-64 systems, so this was a problem.
This patch fixes that.
Signed-off-by: And Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code to detect IO links on Opteron would not check
if the node had actually memory. This could lead to pci_bus_to_node
returning an invalid node, which might cause crashes later
when dma_alloc_coherent passes it to page_alloc_node().
The bug has been there forever but for some reason
it is causing now crashes.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Plug a race in TSC synchronization
We need to do tsc_sync_wait() before the CPU is set online to prevent
multiple CPUs from doing it in parallel - which won't work because TSC
sync has global unprotected state.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Oops. I knew I didn't have the physical versus logical cpu identifiers right
when I generated that patch. It's not nearly as bad as I feared at the time
though.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
modprobe aes does not work on x86_64. i386 has a similar line, this could
be the right fix. Would be nice to have in 2.6.13 final.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't log machine check events left over from boot. Too many BIOSes leave
bogus events in there.
This unfortunately also makes it impossible to log events that caused a
reboot. For people with non broken BIOS there is mce=bootlog
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the sparse mem changes and the kexec changes
were merged into setup.c they came in, in the wrong order.
This patch changes the order so we don't run sparse_init
which uses the bootmem allocator until we all of the
reserve_bootmem calls has been made.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The IA32 ptrace emulation currently returns the wrong registers for fs/gs;
it's returning what x86_64 calls gs_base. We need regs.gsindex in order
for GDB to correctly locate the TLS area. Without this patch, the 32-bit
GDB testsuite bombs on a 64-bit kernel. With it, results look about like
I'd expect, although there are still a handful of kernel-related failures
(vsyscall related?).
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86_64 had hardcoded the VM_ numbers so it broke down when the numbers
were changed.
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch adds boundary check for the MAX_GSI_NUM. Same as the update for
i386, the patch addresses a problem with ACPI SCI IRQ. The patch corrects
the code such that SCI IRQ is skipped and duplicate entry is avoided. The
VIA chipset uses 4-bit IRQ register for internal interrupt routing, and
therefore cannot handle IRQ numbers assigned to its devices. The patch
corrects this problem by allowing PCI IRQs below 16.
Signed-off-by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I was observing reproducible crashes on the "movw %bx,(%rsi)" instruction
below while a process in a recvfrom() system call was copying packet data
to user space. The patch below fixes the exception table and causes the
crash to no longer reproduce. Please apply.
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sync_tsc was using smp_call_function to ask the boot processor to report
it's tsc value. smp_call_function performs an IPI_send_allbutself which is
a broadcast ipi. There is a window during processor startup during which
the target cpu has started and before it has initialized it's interrupt
vectors so it can properly process an interrupt. Receveing an interrupt
during that window will triple fault the cpu and do other nasty things.
Why cli does not protect us from that is beyond me.
The simple fix is to match ia64 and provide a smp_call_function_single.
Which avoids the broadcast and is more efficient.
This certainly fixes the problem of getting stuck on boot which was
very easy to trigger on my SMP Hyperthreaded Xeon, and I think
it fixes it for the right reasons.
Minor changes by AK
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the standard hardware page table manipulation macros.
This is possible now that linux works with all 4 levels
of the page tables.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In an uncensored copy of code from i386 to x86_64 I wound up
with inline assembly with the wrong constraints. Use input
constraints instead of output constraints.
So I know the assembler will do the right thing specify the size
of the operand lidtq and lgdtq instead of just lidt and lgdt.
Make load_segments use an input constraint, and delete the macro fun.
Without having to reload %cs like I do on i386 this code is noticeably
simpler.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While booting with SMT disabled in bios, when using acpi srat to setup
cpu_to_node[], sparse apic_ids create problems.
Without this patch, intel x86_64 boxes with hyperthreading disabled in the
bios (and which rely on srat for numa setup) endup having incorrect values in
cpu_to_node[] arrays, causing sched domains to be built incorrectly etc.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This avoids some potential stack overflows with very deep softirq callchains.
i386 does this too.
TOADD CFI annotation
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Save a byte here and there. Ultimatively useless, but these things always
catch my eyes when reading the code so just fix them for now.
Also I got at least one patch fixing of them already, which gives a good
excuse.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Icecream preprocesses c sources locally, and sends the result off to a remote
host for compiling. It does not recognize includes at assembler level. The
fix is to put the assemberincludes an a separate .s file, which will always be
assembled locally.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use physical mode instead of logical mode to address more CPUs. This is also
used in the CPU hotplug case to avoid a race.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Will be obsolete with physflat.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Not used anymore since quite some time. Just uses -m32 instead.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch will create machinecheck sysdev directories per CPU. All of the
cpus still share the same ctl banks. When compiled with CONFIG_HOTPLUG_CPU,
it will also bring up/down sysdev directories as cpus go up/down. I have
tested the patch along with CONFIG_HOTPLUG_CPU option on in 2.6.13-rc1 kernel.
Minor changes by AK: remove useless unload function
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Keith Manning
Print a boot message for hotplug memory zones
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Minor cleanup.
Move things into their include files, remove obsolete includes, fix
indentation, remove obsolete special cases etc.
I also added the per cpu section to asm-generic/sections.h and fixed
init/main.c to use it.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No need to print kernel addresses there and clarify what the APIC-ID is.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Does not change any semantics because numa_add_cpu checks for CPU 0 anyways.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Various code needs this information now before the actual SMP bootup. Instead
of computing it on the fly while booting the other CPUs set it up now while
initial MPtable/MADT parsing.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the x86_64 cpu hotplug changes went in it added a check in
default_do_nmi() which kills NMI delivery on any CPU but the BSP.
The NMI watchdog is brought up quite some time before the online bit is set
in num_online_cpus so this won't work very well. The nmi watchdogs on cpus
that are not BSP will never be reprogrammed and no NMIs.
Why was this check added? How does an offlined cpu receive an NMI?
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Cc: <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
turn many #if $undefined_string into #ifdef $undefined_string to fix some
warnings after -Wno-def was added to global CFLAGS
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixes boot up lockups on some machines where CPU apic ids don't start with
0
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 machine_power_off was disabling the local apic
and all of it's users wanted to be on the boot cpu.
So call machine_shutdown which places us on the boot
cpu and disables the apics. This keeps us in sync
and reduces the number of cases we need to worry about in
the power management code.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is not safe to call set_cpus_allowed() in interrupt
context and disabling the apics is complicated code.
So unconditionally skip machine_shutdown in machine_emergency_reboot
on x86_64.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We only want to shutdown the apics if reboot_force
is not specified. Be we are doing this both
in machine_shutdown which is called unconditionally
and if (!reboot_force). So simply call machine_shutdown
if (!reboot_force). It looks like something
went weird with merging some of the kexec patches for
x86_64, and caused this.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
machine_restart, machine_halt and machine_power_off are machine
specific hooks deep into the reboot logic, that modules
have no business messing with. Usually code should be calling
kernel_restart, kernel_halt, kernel_power_off, or
emergency_restart. So don't export machine_restart,
machine_halt, and machine_power_off so we can catch buggy users.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add inotify syscall entries to x86-64.
Signed-off-by: Robert Love <rml@novell.com>
Signed-off-by: John McCutchan <ttb@tentacle.dhs.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
