A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
- Support for inter-word delays.
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects.
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlx9WtETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DfrB/92O47HJfHg1xIgOp4BLzT8lA5zQEsy
a8ApcLVLvY6mSfbB/G7RosfoPwTc1eZP5Q2BqzQOBIO+507ao4AcASARmkTwjwkC
eRUJ/THkGyGurs8POtnc5YJlHsT1t743QpqlUNekt+NqognlkPccgc5bNgixfuPD
eVSwVC85SKP3gCpAjVb6FFFmlWr8AKdlgx+41h9QpMNG/85H6xgo4C4Wlajt42/E
wNx+WXzlPyzB5Lc3IGPeF/I/Hu/Ta3hUZLTVpWi5ubM8p4SYGmMZ9l8sURPCz1pK
UMZFpJxx8DWwkj2F/FkoLasfiRqUHIP9K7NfKF0u2xdNbhEk1GA3NAG0
=ctKG
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
Summary:
- Support for inter-word delays
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum"
* tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (104 commits)
spi: sh-msiof: Restrict bits per word to 8/16/24/32 on R-Car Gen2/3
spi: sifive: Remove redundant dev_err call in sifive_spi_probe()
spi: sifive: Remove spi_master_put in sifive_spi_remove()
spi: spi-gpio: fix SPI_CS_HIGH capability
spi: pxa2xx: Setup maximum supported DMA transfer length
spi: sifive: Add driver for the SiFive SPI controller
spi: sifive: Add DT documentation for SiFive SPI controller
spi: sprd: Add a prefix for SPI DMA channel macros
spi: sprd: spi: sprd: Add DMA mode support
dt-bindings: spi: Add the DMA properties for the SPI dma mode
spi: sprd: Add the SPI irq function for the SPI DMA mode
dt-bindings: spi: imx: Add an entry for the i.MX8QM compatible
spi: use gpio[d]_set_value_cansleep for setting chipselect GPIO
spi: gpio: Advertise support for SPI_CS_HIGH
spi: sh-msiof: Replace spi_master by spi_controller
spi: sh-hspi: Replace spi_master by spi_controller
spi: rspi: Replace spi_master by spi_controller
spi: atmel-quadspi: add support for sam9x60 qspi controller
dt-bindings: spi: atmel-quadspi: QuadSPI driver for Microchip SAM9X60
spi: atmel-quadspi: add support for named peripheral clock
...
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAlxwE4kACgkQJWrqGEe9
VoRQVQf+OOkScM6ZbsO2GbMRe0ybMOCOyBXfojPEGtVv80gHHrAPRocLqWMB1Xdb
MSfm7j+lyZU1I8eYVvdYXby7s5FlVWbrh8NSnnwox1QusdmyBm7vcxc6st15Poy/
/WtjE+Cry49eIx5L/pmmNH3AIqMdvSRTJD7NgOYjo/SIq4GLR+KQEgt1VLp/KyO0
TGeMDIT3Q3+MXVwvUh3YlHUwNJ2jOpjpPW94QxD0mef/b9doUlkvrOdHs3JeGQzX
aiiqWI1nRBmjNs34wp7Dyf3G/feplKyi+IS/ghTiijAgwbWdRI7KxrPtyCUYiint
3XqVgZAF/sfFaKFMIiJBMzoLQB15dQ==
=VbaE
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.1' of git://git.infradead.org/linux-mtd into mtd/next
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
AM654 SoC has Cadence Octal SPI controller, which is similar to Cadence
QSPI controller but supports Octal IO(x8 data lines) and Double Data
Rate(DDR) mode. Add new compatible to support OSPI controller on TI's
AM654 SoCs.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Add Amlogic NAND controller dt-bindings for Meson SoC,
Current this driver support GXBB/GXL/AXG platform.
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This updates bindings for the MT7629 SPI-NOR controller.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
This patch adds the documentation of the device tree bindings for the STM32
FMC2 NAND controller.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Move the documentation of the old SPI NOR driver to the place of the new
SPI memory interface based driver.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The main thing this release has been a lot of work on the integration
with SPI NOR flashes, there's been some specific support for a while for
controller features designed to make them perform better but it's not
worked out as well as hoped so the interface has been redesigned in a
way that will hopefully do better - it's already been adopted by a
number of additional controllers so things are looking good. Otherwise
most of the work has been driver specific:
- Support for better integration with NOR flashes from Boris Brezillon
and Yogesh Narayan Gaur plus usage of it in several drivers.
- A big cleanup of the Rockchip driver from Emil Renner Berthing.
- Lots of performance improvements for bcm2835 from Lukas Wunner.
- Slave mode support for pxa2xx from Lubomir Rintel.
- Support for Macronix MXIC, Mediatek MT7629 and MT8183, NPCM PSPI,
and Renesas r8a77470.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlwhLBsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0AGvB/9odNqLjVJiG6v0EIKqLyYXMzCYgmrZ
RyBZoqTKoNmXxv0b/Fdsi8VaiJ8x2WIcqLzhpQlg3twOCvXQbgoA+JzQNyHZlZ1u
8cxfFGebVS6r0k14bkmAVR8LSvGlReOZQLC2MvccVc/UAwN0/p5ncN0xUADHvIOW
/Pmx0/e2uCMx1+OMAudlUXQ5IIbnb5/OjvDfR/7tlVo5YKSgkHBJeunOYSaPSNuO
QNf9+kZxvQ8djYbpYqqHWovPF7JSlQAj0WkMJPB/g3R09E/vatSBlCMnETBJWn/L
wogHquLK/vwRaS+MqTSrGsi0ylpqgxmZrbGKcXKF51fim0EvBg7cMqe6
=ZnI3
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The main thing this release has been a lot of work on the integration
with SPI NOR flashes, there's been some specific support for a while
for controller features designed to make them perform better but it's
not worked out as well as hoped so the interface has been redesigned
in a way that will hopefully do better - it's already been adopted by
a number of additional controllers so things are looking good.
Otherwise most of the work has been driver specific:
- Support for better integration with NOR flashes from Boris
Brezillon and Yogesh Narayan Gaur plus usage of it in several
drivers.
- A big cleanup of the Rockchip driver from Emil Renner Berthing.
- Lots of performance improvements for bcm2835 from Lukas Wunner.
- Slave mode support for pxa2xx from Lubomir Rintel.
- Support for Macronix MXIC, Mediatek MT7629 and MT8183, NPCM PSPI,
and Renesas r8a77470"
* tag 'spi-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (90 commits)
spi: sh-msiof: Reduce the number of times write to and perform the transmission from FIFO
spi: sh-msiof: Add r8a774c0 support
doc: lpspi: Document DT bindings for LPSPI slave mode
spi: lpspi: Let watermark change with send data length
spi: lpspi: Add slave mode support
spi: lpspi: Replace all "master" with "controller"
spi: imx: drop useless member speed_hz from driver data struct
spi: imx: rename config callback and add useful parameters
spi: imx: style fixes
spi: imx: mx51-ecspi: Move some initialisation to prepare_message hook.
spi: imx: add a device specific prepare_message callback
mtd: atmel-quadspi: disallow building on ebsa110
spi: Update NPCM PSPI controller documentation
spi: npcm: Modify pspi send function
spi: Use of_node_name_eq for node name comparisons
spi: dw-mmio: add ACPI support
spi: bcm2835: Synchronize with callback on DMA termination
spi: bcm2835: Speed up FIFO access if fill level is known
spi: bcm2835: Polish transfer of DMA prologue
spi: spi-mem: add support for octal mode I/O data transfer
...
This adds device tree bindings for the RedBoot FIS partition
format.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Atmel SAMA5D2 QuadSPI driver was moved from mtd to spi subsystem,
this change is just moving DT-binding documentation.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Piotr Bugalski <bugalski.piotr@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add documentation for the addr-gpios. This extension to the physmap
binding allow creating flash devices that are paged using GPIOs.
Cc: devicetree@vger.kernel.org
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
- Remove an obsolete hack for PPC32 longtrail systems
- Make of_io_request_and_map() "name" arg optional
- Add vendor prefixes for bitmain, Asus, and Y Soft
- Remove 'interrupt-parent' from bindings as it is implicit
- New properties for wm8994 audio codec
- Add 'clocks' property support to SRAM binding
- Add binding for ASPEED coprocessor interrupt controller
- Various binding spelling and link fixes
-----BEGIN PGP SIGNATURE-----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=AV4E
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- Remove an obsolete hack for PPC32 longtrail systems
- Make of_io_request_and_map() "name" arg optional
- Add vendor prefixes for bitmain, Asus, and Y Soft
- Remove 'interrupt-parent' from bindings as it is implicit
- New properties for wm8994 audio codec
- Add 'clocks' property support to SRAM binding
- Add binding for ASPEED coprocessor interrupt controller
- Various binding spelling and link fixes
* tag 'devicetree-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
Documentation: remove dynamic-resolution-notes reference to non-existent file
dt-bindings: Add Y Soft Corporation vendor prefix
of/fdt: Remove PPC32 longtrail hack in memory scan
dt-bindings: remove 'interrupt-parent' from bindings
pinctrl: tegra: fix spelling in devicetree binding document
usb: dwc3: rockchip: Fix PHY documentation links.
dt-bindings: sound: wm8994: document wlf,csnaddr-pd property
dt-bindings: sound: wm8994: document wlf,spkmode-pu property
dt-bindings: sram: Add 'clocks' as an optional property
dt-bindings: Add vendor prefix for AsusTek Computer Inc.
dt-bindings: misc: ASPEED coprocessor interrupt controller
dt-bindings: gpio: pca953x: Document interrupts, update example
drivers/of: Make of_io_request_and_map() "name" argument optional
dt-bindings: Add bitmain vendor prefix
Documentation: devicetree: tilcdc: fix spelling mistake "suppors" -> "supports"
- Apply reset hacks only when reset is explicitly marked as broken in
the DT
Driver changes:
- Minor cleanup/fixes in the m25p80 driver
- Release flash_np in the nxp-spifi driver
- Add suspend/resume hooks to the atmel-quadspi driver
- Include gpio/consumer.h instead of gpio.h in the atmel-quadspi driver
- Use %pK instead of %p in the stm32-quadspi driver
- Improve timeout handling in the cadence-quadspi driver
- Use mtd_device_register() instead of mtd_device_parse_register() in
the intel-spi driver
-----BEGIN PGP SIGNATURE-----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=uNJl
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.19' of git://git.infradead.org/linux-mtd into mtd/next
Pull SPI NOR updates from Boris Brezillon:
"
Core changes:
- Apply reset hacks only when reset is explicitly marked as broken in
the DT
Driver changes:
- Minor cleanup/fixes in the m25p80 driver
- Release flash_np in the nxp-spifi driver
- Add suspend/resume hooks to the atmel-quadspi driver
- Include gpio/consumer.h instead of gpio.h in the atmel-quadspi driver
- Use %pK instead of %p in the stm32-quadspi driver
- Improve timeout handling in the cadence-quadspi driver
- Use mtd_device_register() instead of mtd_device_parse_register() in
the intel-spi driver
"
- Add the SPI-NAND framework.
- Create a helper to find the best ECC configuration.
- Create NAND controller operations.
- Allocate dynamically ONFI parameters structure.
- Add defines for ONFI version bits.
- Add manufacturer fixup for ONFI parameter page.
- Add an option to specify NAND chip as a boot device.
- Add Reed-Solomon error correction algorithm.
- Better name for the controller structure.
- Remove unused caller_is_module() definition.
- Make subop helpers return unsigned values.
- Expose _notsupp() helpers for raw page accessors.
- Add default values for dynamic timings.
- Kill the chip->scan_bbt() hook.
- Rename nand_default_bbt() into nand_create_bbt().
- Start to clean the nand_chip structure.
- Remove stale prototype from rawnand.h.
Raw NAND controllers drivers changes:
- Qcom: structuring cleanup.
- Denali: use core helper to find the best ECC configuration.
- Possible build of almost all drivers by adding a dependency on
COMPILE_TEST for almost all of them in Kconfig, implies various
fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even
changes in sparc64 and ia64 architectures.
- Clean the ->probe() functions error path of a lot of drivers.
- Migrate all drivers to use nand_scan() instead of
nand_scan_ident()/nand_scan_tail() pair.
- Use mtd_device_register() where applicable to simplify the code.
- Marvell:
* Handle on-die ECC.
* Better clocks handling.
* Remove bogus comment.
* Add suspend and resume support.
- Tegra: add NAND controller driver.
- Atmel:
* Add module param to avoid using dma.
* Drop Wenyou Yang from MAINTAINERS.
- Denali: optimize timings handling.
- FSMC: Stop using chip->read_buf().
- FSL:
* Switch to SPDX license tag identifiers.
* Fix qualifiers in MXC init functions.
Raw NAND chip drivers changes:
- Micron:
* Add fixup for ONFI revision.
* Update ecc_stats.corrected.
* Make ECC activation stateful.
* Avoid enabling/disabling ECC when it can't be disabled.
* Get the actual number of bitflips.
* Allow forced on-die ECC.
* Support 8/512 on-die ECC.
* Fix on-die ECC detection logic.
- Hynix:
* Fix decoding the OOB size on H27UCG8T2BTR.
* Use ->exec_op() in hynix_nand_reg_write_op().
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJbYYGVAAoJECVq6hhHvVaE0poIAJy+VpZl0jTPQ/oO8TQui9hE
IZbc8LwohCvegYYhiY1cNESyMYamDfoK6M93i/0zTJF2AJAxPl25ldT8N5Wr16DO
5Vfsdjv75V8l0JEY2SvWYmC6glOAYs0UEDdcFNJRMPqUnQz+VvBIafJOCQqzo4ZH
SDnLx3XzOxO4PAPnztWEg50WvaqMPt7ThcqoxThHMcQaLrNjgJUsV0mN+vNEv16Q
6gH6hl1C019k+Kj2Zu0vAifHw1K7gIYT4HvqKwstQ6HYUX2IzIzuEpRIcIze0S5z
XKzZ57USItb3l+Y3YwFBLjgP4N+VTT5X59LxdtCOXJ+YvzgxwtKElRvalNcryYI=
=zkEf
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.19' of git://git.infradead.org/linux-mtd into mtd/next
Pull NAND updates from Miquel Raynal:
"
NAND core changes:
- Add the SPI-NAND framework.
- Create a helper to find the best ECC configuration.
- Create NAND controller operations.
- Allocate dynamically ONFI parameters structure.
- Add defines for ONFI version bits.
- Add manufacturer fixup for ONFI parameter page.
- Add an option to specify NAND chip as a boot device.
- Add Reed-Solomon error correction algorithm.
- Better name for the controller structure.
- Remove unused caller_is_module() definition.
- Make subop helpers return unsigned values.
- Expose _notsupp() helpers for raw page accessors.
- Add default values for dynamic timings.
- Kill the chip->scan_bbt() hook.
- Rename nand_default_bbt() into nand_create_bbt().
- Start to clean the nand_chip structure.
- Remove stale prototype from rawnand.h.
Raw NAND controllers drivers changes:
- Qcom: structuring cleanup.
- Denali: use core helper to find the best ECC configuration.
- Possible build of almost all drivers by adding a dependency on
COMPILE_TEST for almost all of them in Kconfig, implies various
fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even
changes in sparc64 and ia64 architectures.
- Clean the ->probe() functions error path of a lot of drivers.
- Migrate all drivers to use nand_scan() instead of
nand_scan_ident()/nand_scan_tail() pair.
- Use mtd_device_register() where applicable to simplify the code.
- Marvell:
* Handle on-die ECC.
* Better clocks handling.
* Remove bogus comment.
* Add suspend and resume support.
- Tegra: add NAND controller driver.
- Atmel:
* Add module param to avoid using dma.
* Drop Wenyou Yang from MAINTAINERS.
- Denali: optimize timings handling.
- FSMC: Stop using chip->read_buf().
- FSL:
* Switch to SPDX license tag identifiers.
* Fix qualifiers in MXC init functions.
Raw NAND chip drivers changes:
- Micron:
* Add fixup for ONFI revision.
* Update ecc_stats.corrected.
* Make ECC activation stateful.
* Avoid enabling/disabling ECC when it can't be disabled.
* Get the actual number of bitflips.
* Allow forced on-die ECC.
* Support 8/512 on-die ECC.
* Fix on-die ECC detection logic.
- Hynix:
* Fix decoding the OOB size on H27UCG8T2BTR.
* Use ->exec_op() in hynix_nand_reg_write_op().
"
Commit 59b356ffd0 ("mtd: m25p80: restore the status of SPI flash when
exiting") is the latest from a long history of attempts to add reboot
handling to handle stateful addressing modes on SPI flash. Some prior
mostly-related discussions:
http://lists.infradead.org/pipermail/linux-mtd/2013-March/046343.html
[PATCH 1/3] mtd: m25p80: utilize dedicated 4-byte addressing commands
http://lists.infradead.org/pipermail/barebox/2014-September/020682.html
[RFC] MTD m25p80 3-byte addressing and boot problem
http://lists.infradead.org/pipermail/linux-mtd/2015-February/057683.html
[PATCH 2/2] m25p80: if supported put chip to deep power down if not used
Previously, attempts to add reboot-time software reset handling were
rejected, but the latest attempt was not.
Quick summary of the problem:
Some systems (e.g., boot ROM or bootloader) assume that they can read
initial boot code from their SPI flash using 3-byte addressing. If the
flash is left in 4-byte mode after reset, these systems won't boot. The
above patch provided a shutdown/remove hook to attempt to reset the
addressing mode before we reboot. Notably, this patch misses out on
huge classes of unexpected reboots (e.g., crashes, watchdog resets).
Unfortunately, it is essentially impossible to solve this problem 100%:
if your system doesn't know how to reset the SPI flash to power-on
defaults at initialization time, no amount of software can really rescue
you -- there will always be a chance of some unexpected reset that
leaves your flash in an addressing mode that your boot sequence didn't
expect.
While it is not directly harmful to perform hacks like the
aforementioned commit on all 4-byte addressing flash, a
properly-designed system should not need the hack -- and in fact,
providing this hack may mask the fact that a given system is indeed
broken. So this patch attempts to apply this unsound hack more narrowly,
providing a strong suggestion to developers and system designers that
this is truly a hack. With luck, system designers can catch their errors
early on in their development cycle, rather than applying this hack long
term. But apparently enough systems are out in the wild that we still
have to provide this hack.
Document a new device tree property to denote systems that do not have a
proper hardware (or software) reset mechanism, and apply the hack (with
a loud warning) only in this case.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
'interrupt-parent' is often documented as part of define bindings, but
it is really outside the scope of a device binding. It's never required
in a given node as it is often inherited from a parent node. Or it can
be implicit if a parent node is an 'interrupt-controller' node. So
remove it from all the binding files.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Documentation was already saying that fixed and dynamic partitioning can
be mixed but was missing a clear description and examples. This commit
adds a proper documentation of how descriptions can be nested and how
layouts can be mixed.
This addition is important for partitions that contain subpartitions.
In such cases partitions have to be properly described in order to let
system handle them correctly.
Depending on situation, nesting descriptions may provide more accurate
logic/structure and/or allow mixing partitioning types (various
"compatible" values).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Commit 30f9f2fb7b ("mtd: denali: add a DT driver") supported the
clock enablement, but did not document it in the DT binding.
In addition to the existing clock, this commit adds more clocks based
on the IP specification.
According to the Denali User's Guide, this IP needs three clocks:
- clk: controller core clock
- clk_x: bus interface clock
- ecc_clk: clock at which ECC circuitry is run
The driver should accept the current single clock for the backward
compatibility, but the DT binding should represent the real hardware,
and future platforms must follow this.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
1. If nand-ecc-strength specified in DT, then controller will use
this ECC strength otherwise ECC strength will be calculated
according to chip requirement and available OOB size.
2. QCOM NAND controller supports only one step size (512 bytes) but
nand-ecc-step-size is required property in DT. This DT property
can be removed and ecc step size can be assigned in driver with
512 bytes value.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Broadcom based home router devices use TRX firmware format. It's a
container that can hold few partitions. If operating system is expected
to access them it has to understand that format and parse flash data
accordingly.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This adds the devicetree binding for the Tegra 2 NAND flash
controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Allow to define a NAND chip as a boot device. This can be helpful
for the selection of the ECC algorithm and strength in case the boot
ROM supports only a subset of controller provided options.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add Reed-Solomon (RS) to the enumeration of ECC algorithms.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND changes:
Core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
* Cleanup/simplification of a few aspects in the driver
* Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
* Use of_device_get_match_data() instead of of_match_device()
* Add an entry in MAINTAINERS for this driver
* Fix nand-ecc-step-size and nand-ecc-strength description in the DT
bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR changes:
Core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
* Mark the driver as "dangerous" in Kconfig
* Fix atomic sequence handling
* Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
* fix a typo in a function name
* add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line
-----BEGIN PGP SIGNATURE-----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=cHjU
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
+ Cleanup/simplification of a few aspects in the driver
+ Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
+ Use of_device_get_match_data() instead of of_match_device()
+ Add an entry in MAINTAINERS for this driver
+ Fix nand-ecc-step-size and nand-ecc-strength description in the
DT bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
+ Mark the driver as "dangerous" in Kconfig
+ Fix atomic sequence handling
+ Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
+ fix a typo in a function name
+ add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line"
* tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd: (66 commits)
mtd: nand: Pass mode information to nand_page_io_req
mtd: cfi_cmdset_0002: Change erase one block to enable XIP once
mtd: cfi_cmdset_0002: Change erase functions to check chip good only
mtd: cfi_cmdset_0002: Change erase functions to retry for error
mtd: cfi_cmdset_0002: Change definition naming to retry write operation
mtd: cfi_cmdset_0002: Change write buffer to check correct value
mtd: cmdlinepart: Update comment for introduction of OFFSET_CONTINUOUS
mtd: bcm47xxpart: add of_match_table with a new DT binding
dt-bindings: mtd: document Broadcom's BCM47xx partitions
mtd: spi-nor: Add support for EN25QH32
mtd: spi-nor: Add support for is25wp series chips
mtd: spi-nor: Add Winbond w25q32jv support
mtd: spi-nor: fsl-quadspi: add support for ls2080a/ls1080a
mtd: spi-nor: stm32-quadspi: explicitly request exclusive reset control
mtd: spi-nor: intel: provide a range for poll_timout
mtd: spi-nor: fsl-quadspi: fix api naming typo _init_ahb_read
mtd: spi-nor: intel-spi: Explicitly mark the driver as dangerous in Kconfig
mtd: spi-nor: intel-spi: Fix atomic sequence handling
mtd: rawnand: Do not check FAIL bit when executing a SET_FEATURES op
mtd: rawnand: use bit-wise majority to recover the ONFI param page
...
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
* Cleanup/simplification of a few aspects in the driver
* Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
* Use of_device_get_match_data() instead of of_match_device()
* Add an entry in MAINTAINERS for this driver
* Fix nand-ecc-step-size and nand-ecc-strength description in the DT
bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
-----BEGIN PGP SIGNATURE-----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=MzWF
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.18' of git://git.infradead.org/linux-mtd into mtd/next
Core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
* Cleanup/simplification of a few aspects in the driver
* Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
* Use of_device_get_match_data() instead of of_match_device()
* Add an entry in MAINTAINERS for this driver
* Fix nand-ecc-step-size and nand-ecc-strength description in the DT
bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
Broadcom based home router devices use partitions which have to be
discovered in a specific way. They are not fixed and there is not any
standard partition table. This commit adds and describes a new custom
binding for such devices.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Update ecc step size, ecc strength, and parity bits supported on
each MTK NAND controller.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
None of the existing platforms connect the R/B pin to a GPIO (they all
use one of the dedicated R/B pin).
Anyway, if we ever get short of native R/B pins, it's probably better
to fallback to STATUS reg polling than trying to poll a GPIO.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Document newly supported device tree properties nand-ecc-strength/
nand-ecc-step-size to specify ECC strength/size.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Bindings are supposed to be organized by device class/function. Move a
couple of powerpc 4xx bindings to the correct binding directory.
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
* Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Driver changes:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
-----BEGIN PGP SIGNATURE-----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=uvio
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.17' of git://git.infradead.org/linux-mtd into mtd/next
Core changes:
* Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Driver changes:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
to the same QSPI controller
* Remove an unneeded driver.bus assigned in the fsl-qspi driver
-----BEGIN PGP SIGNATURE-----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=Wrxi
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.17' of git://git.infradead.org/linux-mtd into mtd/next
* Make fsl-quaspi assign different names to MTD devices connected
to the same QSPI controller
* Remove an unneeded driver.bus assigned in the fsl-qspi driver
Improve the bindings example by adding an example of how to represent
two SPI NOR devices.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This mode is not used by any existing setup and should not be used
because it overwrites the BBMs. Let's just remove it before someone
starts using it.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
On Armada 7K/8K we need to explicitly enable the register clock. This
clock is optional because not all the SoCs using this IP need it but at
least for Armada 7K/8K it is actually mandatory.
The binding documentation is updated accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Provide a way to specify the endianness to use when accessing a
memory-mapped flash.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The deprecated pxa3xx_nand.c driver does not exist anymore, it has been
replaced by marvell_nand.c which has its own up-to-date documentation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
- Convert to use memblock_virt_alloc in DT code which supports bootmem
arches. With this we can remove the arch specific
early_init_dt_alloc_memory_arch() functions.
- Enable running the DT unittests on UML
- Use SPDX license tags on DT files
- Fix early FDT kconfig ifdef logic
- Clean-up unittest Makefile
- Fix function comment for of_irq_parse_raw
- Add missing documentation for linux,initrd-{start,end} properties
- Clean-up of binding examples using uppercase hex
- Add trivial devices W83773G and Infineon TLV493D-A1B6
- Add missing STM32 SoC bindings
- Various small binding doc fixes
-----BEGIN PGP SIGNATURE-----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=v6gj
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- Convert to use memblock_virt_alloc in DT code which supports
bootmem arches. With this we can remove the arch specific
early_init_dt_alloc_memory_arch() functions.
- Enable running the DT unittests on UML
- Use SPDX license tags on DT files
- Fix early FDT kconfig ifdef logic
- Clean-up unittest Makefile
- Fix function comment for of_irq_parse_raw
- Add missing documentation for linux,initrd-{start,end} properties
- Clean-up of binding examples using uppercase hex
- Add trivial devices W83773G and Infineon TLV493D-A1B6
- Add missing STM32 SoC bindings
- Various small binding doc fixes
* tag 'devicetree-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (23 commits)
xtensa: remove arch specific early DT functions
x86: remove arch specific early_init_dt_alloc_memory_arch
nios2: remove arch specific early_init_dt_alloc_memory_arch
mips: remove arch specific early_init_dt_alloc_memory_arch
metag: remove arch specific early DT functions
cris: remove arch specific early DT functions
libfdt: remove unnecessary include directive from <linux/libfdt.h>
of: unittest: refactor Makefile
of/fdt: use memblock_virt_alloc for early alloc
of: Use SPDX license tag for DT files
of/fdt: Fix #ifdef dependency of early flattree declarations
dt-bindings: h8300 clocksource: correct spelling of pulse
dt-bindings: imx6q-pcie: Add required property for i.MX6SX
mmc: Don't reference Linux-specific OF_GPIO_ACTIVE_LOW flag in DT binding
dt-bindings: Use lower case hex in unit-addresses
dt-bindings: display: panel: Fix compatible string for Toshiba LT089AC29000
dt-bindings: Add Infineon TLV493D-A1B6
dt-bindings: mailbox: ti,message-manager: Fix interrupt name error
dt-bindings: chosen: Document linux,initrd-{start,end}
dt-bindings: arm: document supported STM32 SoC family
...
Core changes:
* Rework core functions to avoid duplicating generic checks in
NAND/OneNAND sub-layers
* Update the MAINTAINERS entry to reflect the fact that MTD
maintainers now use a single git tree
Driver changes:
* CFI: use macros instead of inline functions to limit stack
usage and make KASAN happy
NAND changes:
Core changes:
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
SPI NOR changes:
Core changes:
* Add support to new ISSI and Cypress/Spansion memory parts.
* Fix support of Micron memories by checking error bits in the FSR.
* Fix update of block-protection bits by reading back the SR.
* Restore the internal state of the SPI flash memory when removing the
device.
Driver changes:
* Maintenance for Freescale, Intel and Metiatek drivers.
* Add support of the direct access mode for the Cadence QSPI controller.
-----BEGIN PGP SIGNATURE-----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=Mxo2
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"MTD core changes:
- Rework core functions to avoid duplicating generic checks in
NAND/OneNAND sub-layers
- Update the MAINTAINERS entry to reflect the fact that MTD
maintainers now use a single git tree
MTD driver changes:
- CFI: use macros instead of inline functions to limit stack usage
and make KASAN happy
NAND core changes:
- Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
- Introduce the ->exec_op() infrastructure
- Rework NAND buffers handling
- Fix ECC requirements for K9F4G08U0D
- Fix nand_do_read_oob() to return the number of bitflips
- Mark K9F1G08U0E as not supporting subpage writes
NAND driver changes:
- MTK: Rework the driver to support new IP versions
- OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and
fix DT support
- Marvell: Add a new driver to replace the pxa3xx one
SPI NOR core changes:
- Add support to new ISSI and Cypress/Spansion memory parts.
- Fix support of Micron memories by checking error bits in the FSR.
- Fix update of block-protection bits by reading back the SR.
- Restore the internal state of the SPI flash memory when removing
the device.
SPI NOR driver changes:
- Maintenance for Freescale, Intel and Metiatek drivers.
- Add support of the direct access mode for the Cadence QSPI
controller"
* tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd: (93 commits)
mtd: nand: sunxi: Fix ECC strength choice
mtd: nand: gpmi: Fix subpage reads
mtd: nand: Fix build issues due to an anonymous union
mtd: nand: marvell: Fix missing memory allocation modifier
mtd: nand: marvell: remove redundant variable 'oob_len'
mtd: nand: marvell: fix spelling mistake: "suceed"-> "succeed"
mtd: onenand: omap2: Remove redundant dev_err call in omap2_onenand_probe()
mtd: Remove duplicate checks on mtd_oob_ops parameter
mtd: Fallback to ->_read/write_oob() when ->_read/write() is missing
mtd: mtdpart: Make ECC stat handling consistent
mtd: onenand: omap2: print resource using %pR format string
mtd: mtk-nor: modify functions' name more generally
mtd: onenand: samsung: remove incorrect __iomem annotation
MAINTAINERS: Add entry for Marvell NAND controller driver
ARM: OMAP2+: Remove gpmc-onenand
mtd: onenand: omap2: Configure driver from DT
mtd: onenand: omap2: Decouple DMA enabling from INT pin availability
mtd: onenand: omap2: Do not make delay for GPIO OMAP3 specific
mtd: onenand: omap2: Convert to use dmaengine for memcpy
mtd: onenand: omap2: Unify OMAP2 and OMAP3 DMA implementation
...
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
-----BEGIN PGP SIGNATURE-----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=TXIU
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.16' of git://git.infradead.org/linux-mtd into mtd/next
Pull NAND changes from Boris Brezillon:
"
Core changes:
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
"
Compatible property is required for OMAP2+ mtd driver. Also
add INT pin gpio description and delete unused dma-channel
property.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Document the legacy and the new bindings for Marvell NAND controller.
The pxa3xx_nand.c driver does only support legacy bindings, which are
incomplete and inaccurate. A rework of this controller (called
marvell_nand.c) does support both.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There are already an atmel,rb and an allwinner,rb properties, let's not
make other ones and instead use a generic term: nand-rb to define NAND
chips Ready/Busy lines.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
DT unit addresses should be lower case hex. Fix all the
binding examples.
Converted with the following command from Krzysztof Kozlowski:
sed -e 's/@\([a-fA-F0-9_-]*\) {/@\L\1 {/' -i $(find Documentation/devicetree/bindings -name '*.txt')
Signed-off-by: Rob Herring <robh@kernel.org>
In order to improve the bindings documentation, explicitly pass the name
of the clocks: "qspi_en" and "qspi", which are mandatory.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
This reverts commit b07815d4ea.
The reverted commit was merged into v4-15-rc1 by mistake: it was taken
from the IMX tree but the patch has never been sent to linux-mtd nor
reviewed by any spi-nor maintainers.
Actually, it would have been rejected since we add new values for the
'compatible' DT property only for SPI NOR memories that don't support
the JEDEC READ ID op code (0x9F).
Both en25s64 and sst25wf040b support the JEDEC READ ID op code, hence
should use the "jedec,spi-nor" string alone as 'compatible' value.
See the following link for more details:
http://lists.infradead.org/pipermail/linux-mtd/2017-November/077425.html
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Improve the binding example by removing all the leading 0x to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
Converted using the following command:
find Documentation/devicetree/bindings -name "*.txt" -exec sed -i -e 's/([^ ])\@0x([0-9a-f])/$1\@$2/g' {} +
This is a follow up to commit 48c926cd34
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Rob Herring <robh@kernel.org>
