This patch converts the ar7_wdt driver to become
a platform driver. The AR7 SoC specific identification
and base register calculation is performed by the board
code, therefore we no longer need to have access to
ar7_chip_id. We also remove the reboot notifier code to
use the platform shutdown method as Wim suggested.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WDIOC_SETTIMEOUT argument is supposed to be a "seconds" value.
However, the book E wdt currently treats it as a "period" which is
interpreted in a board-specific way.
This patch allows the user to pass in a "seconds" value and the driver
will set the smallest timeout that is at least as large as specified
by the user. It's been tested on e500 hardware and works as
expected.
The patch only modifies the CONFIG_FSL_BOOKE case, the CONFIG_4xx case
is left unmodified as I don't have any hardware to test it on.
Signed-off-by: Chris Friesen <cfriesen@nortel.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove use of CLOCK_TICK_RATE in favor of using clock framework
for getting timer frequency.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
I saw Julia Lawalls various commits fixing up the use of rounding
macros and since my already submitted patch was not caught in this
I took it upon myself to fix it up for this driver as well.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WM831x series of devices provide a watchdog with configurable
behaviour on timer expiry.
Currently this driver support refreshes via a register or GPIO line and
autonomous refreshes from a hardware source (eg, a clock).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add watchdog device driver for the Nuvoton NUC900 series SoCs.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add support for watchdog found on SBC-FITPC2 board.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
AR7 is currently being resubmitted for mainline inclusion
and we changed the path to the ar7-specific headers
from ar7 to mach-ar7 to reflect the other MIPS-based
boards header hierarchy. This patch will avoid any future
compilation failure due to missing headers.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Stop referencing CLOCK_TICK_RATE in the KS8695 drivers, rather refer
to a KS8695_CLOCK_RATE.
Issue pointed out by Russell King on arm-linux-kernel mailing list.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the COH 901 327 found in U300 is clocked at 32 kHz we need
to wait for the interrupt clearing flag to propagate through
hardware in order not to accidentally fire off any interrupts
when we enable them.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix a number of build errors in the ep93xx watchdog driver due
to missing io.h
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the W83627EHF/EF and W83627EHG/EG chipsets.
Signed-off-by: Slobodan Tomić <stomic@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch replaces the hardcoded 255 seconds limit for a real limit based on
oscr_freq.
Also, the 'firmware_version' field is changed to '1' to allow the user
space application to easily detect that this driver supports a higher
maximum timeout.
Signed-off-by: Raphael Assenat <raph@8D.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Don't forget to unlock io_lock when w83697ug_select_wd_register fails in
wdt_ctrl.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Using the RTAS watchdog driver to read out the temperature crashes
on a PXCAB:
Unable to handle kernel paging request for data at address 0xfe347b50
Faulting instruction address: 0xc00000000001af64
Oops: Kernel access of bad area, sig: 11 [#1]
The wrong usage of "(void *)__pa(&temperature)" in rtas_call() is
removed by using the function rtas_get_sensor() which does the
right thing.
Signed-off-by: Adrian Reber <adrian@lisas.de>
Acked-by: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change the wdt_pci.c watchdog driver so that the code is the same for
both the PCI-WDT500 as the PCI-WDT501 card. The selection of the card
is now being done via the module parameter: 'type' instead of the
config option CONFIG_WDT_501_PCI.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a priority option so that the user can choose if we do the NMI
first or last.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch contains two fixes:
1)In omap_wdt_probe() the watchdog is reset and disabled. This
requires register access and the clks needs to be enabled temporarily
2)In omap_wdt_open() the timer register needs to be reloaded
to trigger a new timer value (the default of 60s)
Tested on OMAP34xx platform (Zoom1)
Reviewed-by: Kevin Hilman <khilman@ti.deeprootsystems.com>
Signed-off-by: Ulrik Bech Hald <ubh@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This add watchdog driver for broadcom 47xx device.
It uses the ssb subsytem to access embeded watchdog device.
Because the watchdog timeout is very short (about 2s), a soft timer is used
to increase the watchdog period.
Note : A patch for exporting the ssb_watchdog_timer_set will
be submitted on next linux-mips merge. Without this patch it can't
be build as a module.
Signed-off-by: Aleksandar Radovanovic <biblbroks@sezampro.rs>
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Tested-by: Florian Fainelli <florian@openwrt.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Implementation of twl4030 watchdog driver.
Signed-off-by: Timo Kokkonen <timo.t.kokkonen@nokia.com>
Signed-off-by: Atal Shargorodsky <ext-atal.shargorodsky@nokia.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds support for the U300 COH 901 327 watchdog for the
U300 platform recently added to RMK:s ARM tree.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add NMI sourcing functionality (Can only be active if nmi_watchdog is
inactive).
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Bugzilla: 9868 & 10195.
There seems to be a bug into the SMM code that handles TCO Timeout SMI.
Andriy Gapon found that the code on his DG33TL system does the following:
> The handler is quite simple - it tests value in TCO1_CNT against 0x800, i.e.
> checks TCO_TMR_HLT. If the bit is set the handler goes into an infinite loop,
> apparently to allow the second timeout and reboot. Otherwise it simply clears
> TIMEOUT bit in TCO1_STS and that's it.
> So the logic seems to be reversed, because it is hard to see how TIMEOUT can
> get set to 1 and SMI generated when TCO_TMR_HLT is set (other than a
> transitional effect).
The only trick we have is to bypass the SMM code by turning of the generation
of the SMI#. The trick can only be enabled by setting the vendorsupport module
parameter to 911. This trick doesn't work well on laptop's.
Note: this is a dirty hack. Please handle with care. The only real fix is that
the bug in the SMM bios code get's fixed.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
According to 9.1.33 on p.343 of ICH8.pdf RCBA can be disabled by
hardware if bit 0 of RCBA register is not set.
Perform correct check for this to prevent memory corruption under
some virtual machines where this feature is disabled.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Vasily Averin <vvs@openvz.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
A pointer to probe and remove functions is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
So far, MPC512x used mpc512x_find_ips_freq() to get the bus frequency,
while MPC52xx used mpc52xx_find_ipb_freq(). Despite the different
clock names (IPS vs. IPB) the code was identical.
Use common code for both processor families.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Orion watchdog driver is also used on Kirkwood.
Convention is to use orion5x for stuff specific to 88F5xxx Orion chips
and simply "orion" for shared stuff across SoCs including Kirkwood.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The Kirkwood architecture uses the same watchdog device as the Orion
architecture. This patch adds orion5x_wdt as a platform device for
Kirkwood.
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The name of the define for the Reset-Out-Mask register as well as its
bit for the watchdog reset are changed to match the names used for
Kirkwood (which in turn match the processor specification more
closely). There is no functional change.
This patch prepares for adding orion5x_wdt as a platform device to
Kirkwood.
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Symbols like SOFT_RESET are way too generic to be exported at large.
To avoid this, let's move the mbus bridge register defines into a
separate file and include it where needed. This affects mach-kirkwood,
mach-loki, mach-mv78xx0 and mach-orion5x simultaneously as they all
share code in plat-orion which relies on those defines.
Some other defines have been moved to narrower scopes, or simply deleted
when they had no user.
This fixes compilation problem with mpt2sas on the above listed
platforms.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A pointer to omap_wdt_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alan Cox <alan@redhat.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: George G. Davis <gdavis@mvista.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A pointer to ks8695wdt_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alan Cox <alan@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A pointer to at91wdt_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ilpo Jarvinen <ilpo.jarvinen@helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Removes ARM26 sections from Kconfig and Makefile, because
ARM26 is long gone.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* Added a callback to disable the watchdog on shutdown.
* Use a separate ping function to reduce the number of register accesses
if the watchdog is already enabled and just needs to be reloaded.
* Minor cleanup of function names.
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The i6300ESB watchdog should be stopped before userspace has access to the
watchdog. So fix this and restructure the initialization sequence into:
* See if we have a i6300 device
* make sure that we have valid module parameters
* Initialize the device
* register the /dev/watchdog device so that userspace has access
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>